User Tools

Site Tools


toh:edimax:edimax_br-6478ac_v2

Edimax BR-6478AC V2

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.

Generic Router

OpenWrt support

Supported.

Hardware highlights

CPU Ram Flash Network WLAN USB Serial JTag
MT7620A @ 580 MHz 64 MiB 8 MiB 5x 1000 abgnac 1x 2.0 Yes ?

Hardware

Info

Architecture: modified MIPS (Lexra RLX5281 cpu cores)
Vendor: RealTek
Bootloader: Same bootloader as the RTL8651c
System-On-Chip: Realtek RTL8197D
CPU/Speed 660 MHz
Flash-Chip: Macronix MX25L3206E
Flash size: 4MB
RAM: Nanya NT5TU32M16DG 64MB
Wireless: 2.4GHz: Realtek RTL8192CE 2T2R 802.11bgn
Wireless: 5GHz: Realtek RTL8812AR 2T2R 802.11ac
Ethernet: Realtek RTL8367RB GbE
USB: USB 2.0 (unpopulated,unsoldered)
Serial: Yes
JTAG: Yes

Flash Layout

Address Layout:

0x0 Bootloader
0x6000 Flash Hardware settings
0x8000 Flash Default Settings
0x10000 Linux image flash offset start
0x40000 Linux image flash offset end
0xE0000 Root image offset start
0x150000 Root image offset end
0x400000 End of 4096KB flash

Photos

Front Casing:

Rear Casing:

Insert photo of backside label

PCB:

Opening the case

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for Edimax BR-6478AC V2 v1.0
EXAMPLE 115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

OEM bootlog

U-Boot 1.1.3 (Feb 24 2015 - 13:04:02) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. spi_wait_nsec: 29 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.1.2.0 -------------------------------------------- ASIC 7620_MP (Port5<->GigaSW) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Feb 24 2015 Time:13:04:02 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes #Reset_MT7530 Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 5: Load ucos code to SDRAM via TFTP Client. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 3 0 3: System Boot system code via Flash. ## Booting image at bc070000 ... raspi_read: from:70000 len:40 Magic number at 0xBC070000 raspi_read: from:70014 len:40 Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 6836140 Bytes = 6.5 MB Load Address: 80000000 Entry Point: 8000c2f0 raspi_read: from:70054 len:684fac Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c2f0) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (root@localhost.localdomain) (gcc version 3.4.2) #1 Thu Sep 10 14:51:59 CST 2015 The CPU feqenuce set to 580 MHz PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe CPU revision is: 00019650 (MIPS 24Kc) Software DMA cache coherency Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=1f05 console=ttyS0 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=000626cc Readback ErrCtl register=000626cc Memory: 61244k/65536k available (2599k kernel code, 4292k reserved, 654k data, 180k init, 0k highmem) Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Console: colour dummy device 80x25 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_GPIOMODE = 1a301d RALINK_GPIOMODE = 18301d PPLL_CFG1=0xe64000 MT7620 PPLL lock PPLL_DRV =0x80080504 start PCIe register access RALINK_RSTCTRL = 2400000 RALINK_CLKCFG1 = 75afffc0 *************** MT7620 PCIe RC mode ************* PCIE0 enabled init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 20200000 res[1]->end = 2020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20000000 res[0]->end = 200fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Load Kernel WDG Timer Module Load Ralink Timer0 Module RT3xxx EHCI/OHCI init. squashfs: version 4.0 (2009/01/31) Phillip Lougher fuse init (API version 7.15) msgmni has been set to 119 io scheduler noop registered (default) Init GPIO Interrupt ***********Init LED Driver Finishing***************** Ralink_gpio_init_irq LED & GPIO & LAN Status Driver LED_VERSION Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A brd: module loaded deice id : c2 20 17 c2 20 (2017c220) MX25L6405D(c2 2017c220) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536 Creating 8 MTD partitions on "raspi": 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000070000 : "Cimage" 0x000000070000-0x000000190000 : "Kernel" 0x000000190000-0x0000007e0000 : "RootFS" 0x000000070000-0x0000007e0000 : "Uimage" 0x0000007e0000-0x000000800000 : "FreeSpace" rdm_major = 240 SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x43762077 Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x43762077 PROC INIT OK! PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected i8042.c: i8042 controller self test timeout. Trying to free nonexistent resource <0000000000000060-000000000000006f> mice: PS/2 mouse device common for all mice Ralink APSoC Hardware Watchdog Timer u32 classifier Performance counters on Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (956 buckets, 3824 max) ctnetlink v0.93: registering with nfnetlink. matchsize=264 xt_time: kernel timezone is -0000 GRE over IPv4 demultiplexor driver gre: can't add protocol ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux TCP cubic registered NET: Registered protocol family 17 @@@@@@@@@@@@@@@@@@@@@ Begin creat a_g_isolation proc @@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@ End of creat a_g_isolation proc @@@@@@@@@@@@@@@@ dnshijack L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 L2TP IP encapsulation support (L2TPv3) L2TP netlink interface L2TP ethernet pseudowire support (L2TPv3) 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:5. Freeing unused kernel memory: 180k freed init started: BusyBox v1.15.2 (2015-09-10 14:24:40 CST) starting pid 24, tty '': '/etc/rc.sh' cannot run '/etc/rc.sh': No such file or directory starting pid 25, tty '': '-/bin/sh' console. Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.15.2 (2015-09-10 14:24:40 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Thu Sep 10 14:42:49 UTC 2015 Set: phy[0].reg[0] = 3900 flash default ********************************************************************** * OpenVPN Key Default. * ********************************************************************** 16384 bytes (0 MB) copied,0.515 seconds,0.000 MB/s 32768 bytes (0 MB) copied,0.523 seconds,0.000 MB/s 16384 bytes (0 MB) copied,0.018 seconds,0.000 MB/s gzip: invalid magic 32768 bytes (0 MB) copied,0.041 seconds,0.000 MB/s gzip: invalid magic / Started WatchDog Timer. Started WatchDog Timer. watchdog: ioctl 0xc00457Raeth v3.0 (06Tasklet f,SkbRecycleai) led: phy_tx_ring = 0x034e8000, tx_ring = 0xa34e8000 phy_rx_ring0 = 0x034e9000, rx_ring0 = 0xa34e9000 SMACCR1 -- : 0x000074da SMACCR0 -- : 0x386845c6 InESW: Link Status Changed - Port5 Link UP apCDMA_CSG_CFG = 81000000 prGDMA1_FWD_CFG = 20710000 opriate ioctl for device ==> WAN MTU 1500 device eth2 entered promiscuous mode Initialize rai0 interface ****************Use External RADIUS****************** Initialize ra0 interface ****************Use External RADIUS****************** >>> wireless_driver() >>> Loading 2.4G Wireless Driver >>> Loading rt2860v2_ap rt2860v2_ap: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint === pAd = c07b7000, size = 926112 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.2.0 RX DESC a379f000 size = 2048 @@@ 7620 AdvContral=0 default ApCliAPSDCapable[0]=1 RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860AP/SingleSKU.dat --> Error opening /etc/Wireless/RT2860AP/SingleSKU.dat RTMPSetDefaultChannel() : default channel to 1 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff1c E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -2, D2 = 10, CalCode = 28 !!! RT6352_Temperature_Init : BBPR49 = 0xfffffffe RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff4 Current Temperature from BBP_R49=0xffffffee TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= d, phase=3e) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 3, phase=3a) TX IQ Calibration Done! MCS Set = ff ff 00 00 01 rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe SYNC - BBP R4 to 20MHz.l rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 74:da:38:68:45:c6 <==== rt28xx_init, Status=0 0x1300 = 00064300 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ APStop: go to ed_monitor_exit()!! @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== >>> wireless_driver() >>> Loading 5G Wireless Driver >>> Loading rlt_wifi register rt2860 === pAd = c0e02000, size = 1401480 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0d00000, csr_addr=0xc0d00000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is FLASH mode build time = 20140408060640a rom patch for E3 IC platform = ALPS hw/sw version = �� patch version =  FW Version:0.0.00 Build:1 Build Time:201406241830____ fw for E3 IC RX[0] DESC a2a04000 size = 4096 RX[1] DESC a2a05000 size = 4096 @@@ 7612 AdvContral=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! default ApCliAPSDCapable[0]=1 RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860AP/SingleSKU.dat --> Error opening /etc/Wireless/RT2860AP/SingleSKU.dat 1. Phy Mode = 49 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (173) get_chl_grp:illegal channel (173) Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 2. Phy Mode = 49 3. Phy Mode = 49 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 TX0 power compensation = 0x38 TX1 power compensation = 0x38 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) mt76x2_calibration(channel = 42) The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 74:da:38:68:45:c7 mt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 original vga value(chain0) = 5c original vga value(chain1) = 5c <==== rt28xx_init, Status=0 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ APStop: go to ed_monitor_exit()!! @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== andes_pci_erasefw ==>rlt_wlan_chip_onoff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0x20b, Reg-WlanFunCtrl=0x20b Setup BRIDGE interface ifconfig: ioctl 0x8913 failed: No such device bridge br0 doesn't exist; can't delete it [bridge] Setup bridge... device eth2.1 entered promiscuous mode route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x208, Reg-WlanFunCtrl=0x209 build time = 20140408060640a rom patch for E3 IC platform = ALPS hw/sw version = �� patch version =  FW Version:0.0.00 Build:1 Build Time:201406241830____ fw for E3 IC RX[0] DESC a2a04000 size = 4096 RX[1] DESC a2a05000 size = 4096 @@@ 7612 AdvContral=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! default ApCliAPSDCapable[0]=1 RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860AP/SingleSKU.dat --> Error opening /etc/Wireless/RT2860AP/SingleSKU.dat 1. Phy Mode = 49 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (173) get_chl_grp:illegal channel (173) Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 2. Phy Mode = 49 3. Phy Mode = 49 andes_pci_fw_init 0x1300 = 00064320 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 TX0 power compensation = 0x38 TX1 power compensation = 0x38 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 mt76x2_single_sku::DefaultTargetPwr = 26 mt76x2_single_sku::DefaultTargetPwr = 0x1a, delta_power = 0x0 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) mt76x2_calibration(channel = 42) The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 74:da:38:68:45:c7 mt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 original vga value(chain0) = 5c original vga value(chain1) = 5c <==== rt28xx_init, Status=0 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process device rai0 entered promiscuous mode RX DESC a379f000 size = 2048 @@@ 7620 AdvContral=0 default ApCliAPSDCapable[0]=1 RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860AP/SingleSKU.dat --> Error opening /etc/Wireless/RT2860AP/SingleSKU.dat RTMPSetDefaultChannel() : default channel to 1 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff1c E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -2, D2 = 11, CalCode = 30 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffff0 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= d, phase=3e) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 3, phase=3b) TX IQ Calibration Done! MCS Set = ff ff 00 00 01 rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe SYNC - BBP R4 to 20MHz.l rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 74:da:38:68:45:c6 <==== rt28xx_init, Status=0 0x1300 = 00064300 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process device ra0 entered promiscuous mode br0: port 3(ra0) entering forwarding state br0: port 3(ra0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 1(eth2.1) entering forwarding state br0: port 1(eth2.1) entering forwarding state route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process Static DHCP Leases disable! route: ioctl 0x890c failed: No such process route: ioctl 0x8br0: port 3(ra0) entering forwarding state 90br0: port 2(rai0) entering forwarding state c br0: port 1(eth2.1) entering forwarding state failed: No such process Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Set: phy[4].reg[0] = 3900 Set: phy[1].reg[0] = 3300 Set: phy[2].reg[0] = 3300 Set: phy[3].reg[0] = 3300 Set: phy[4].reg[0] = 3300 br0: port 3(ra0) entering forwarding state br0: port 3(ra0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 1(eth2.1) entering forwarding state br0: port 1(eth2.1) entering forwarding state Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Set: phy[4].reg[0] = 3900 Set: phy[1].reg[0] = 3300 Set: phy[2].reg[0] = 3300 Set: phy[3].reg[0] = 3300 Set: phy[4].reg[0] = 3300 Setup WAN interface kill: you need to specify whom to kill Close Wan(eth2.2) Interface!! device eth2 is not a slave of br0 device eth2.1 is already a member of a bridge; can't enslave it to bridge br0. =====config-vlan.sh Start 3 LLLLW====== Special Tag Disabled REG_ESW_WT_MAC_ATC is 0x7ff0002 done. Set: phy[0].reg[0] = 3300 ********************************************************************** * Enable WSC_UPnP * ********************************************************************** ********************************************************************** * Enable LLTD * ********************************************************************** killall: lld2d: no process killed libupnp: using UDP SSDP_PORT = 1900 libupnp: using UDP SSDP_PORT = 1900 killall: snmpd: no process killed udhcpc (v1.15.2) started into eth2.2.deconfig ------> 802.1x--------->Enter ------> 802.1x------>Exit killall: radiusd: no process killed RADIUS server disable !! kill: you need to specify whom to kill dns_hijack_enabled = 1 ********************************************************************** * FREE Page,Dentries and Inodes Cache * ********************************************************************** >>> Update system time every 30min killall: crond: no process killed killall: gpio: no process killed MemFree: 38024 kB Cached: 3456 kB ralink_gpio:ioctl GPIO REG info.irq = 2 >>> Run iQsetup kill: you need to specify whom to kill boa: server version Boa/0.94.14rc21 boa: server built Sep 10 2015 at 14:44:27. boa: starting server pid=1040, port 80 addcgiext .lua,.lp,.php axhttpd/1.4.9: listening on ports 80 (http) and 443 (https) iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. No dnrd daemon found. Exiting. cat: can't open '/etc/resolv.conf': No such file or directory Notice: caching turned off MAC:[74,da,38,68,45,c6] [7_,__,_8,__,__,c6] Change:[c4,da,36,68,45,78] DDNS UID:[64r8r6ghbo] ReInit APMIB excute flash gen-pin 3 bit RAND -> 173 4 bit MAC -> 45c6 32 bit md5sum -> b23eb4ec1fcc741fbd74cbd2007ad5b3 7 bit producestr -> 2341741 ReInit APMIB ReInit APMIB ##### Generated PIN 2.4G= 23417410 ###### 3 bit RAND -> 173 4 bit MAC -> 45c7 32 bit md5sum -> 402a887e3983f1ecc93a3834da63d8b9 7 bit producestr5G -> 4028873 ReInit APMIB ReInit APMIB ##### Generated PIN 5G= 40288734 ###### IQ Monitor Start! Channel_Number 2 ~ 10 Min_ChThe 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 annel_Number = 2 Min_Channel_C@@@ APStop: go to ed_monitor_exit()!! ou@@@ ed_monitor_exit : ===> nt@@@ ed_monitor_exit : <=== = 0 2.4G Auto Channel=2br0: port 3(ra0) entering forwarding state RX DESC a379f000 size = 2048 @@@ 7620 AdvContral=0 default ApCliAPSDCapable[0]=1 RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860AP/SingleSKU.dat --> Error opening /etc/Wireless/RT2860AP/SingleSKU.dat 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff1c E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -1, D2 = 10, CalCode = 26 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffff3 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= d, phase=3e) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 2, phase=3b) TX IQ Calibration Done! MCS Set = ff ff 00 00 01 rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe rt635x_tssi0_dc is 0x00000007 rt635x_tssi1_dc is 0xfffffffe The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 74:da:38:68:45:c6 <==== rt28xx_init, Status=0 0x1300 = 00064300 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== br0: port 3(ra0) entering forwarding state br0: port 3(ra0) entering forwarding state


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Tags

How to add tags

toh/edimax/edimax_br-6478ac_v2.txt · Last modified: 2017/01/12 06:39 by JMThomas