User Tools

Site Tools


toh:engenius:engenius_esr9753

EnGenius ESR9753

The ESR9753 and the ESR9752 are very similar devices and there are many branded version of this device. Even other devices (ESR6600) look very similar. It is based on the RT3052 chipset, has 4MB of flash and 32MB of ram. It is at least known as the Sitecom WL-611.

Supported Versions

Hardware Highlights

Installation

At least 15.05 works on the ESR9752.

I installed the firmware using a serial cable and a TFTP server. The TX, RX and GND pins are clearly marked on my device.

In the bootloader I used option 2 to download from the TFTP server and write the file to flash.

I used the initramfs version (NOT the sysupgrade). https://downloads.openwrt.org/chaos_calmer/15.05/ramips/rt305x/openwrt-15.05-ramips-rt305x-esr-9753-initramfs-uImage.bin

Once openwrt booted I upload the sysupgrade through the web interface.

Flash Layout

Engenius ESR 9753 Flash Layout
Layer0 Parallel NOR device 4096KiB
Layer1 mtd0 u-boot 192KiB mtd1 art 64KiB mtd3 firmware 3776KiB
Layer2 mtd4 kernel 1026KiB mtd5 rootfs 2749KiB
mountpoint /
filesystem mini_fo/overlayfs
Layer3 mtd6 rootfs_data 576KiB
Size in KiB 192KiB 64Kib 1026KiB 2749KiB 576KiB
Name u-boot art kernel rootfs_data
mountpoint none none none /rom /overlay
filesystem none none none SquashFS JFFS2

OEM easy installation

There is no easy installation. Perhaps installing dd-wrt allows to upgrade to OpenWrt but I have not tried this.

OEM installation using the TFTP method

Upgrading OpenWrt

The normal upgrading procedure works

generic.sysupgrade

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The EnGenius ESR9753 has the following buttons:

BUTTON Event
Reset reset
WPS wps

Hardware

Info

General
Brand EnGenius
Model ESR-9753
Versions
Device Type WiFi Router
Availability Discontinued
Comments - general
OpenWrt Support
Supported Since Revision https://dev.openwrt.org/changeset/29824
Supported Since Release 12.09
Supported Current Release 15.05
Unsupported
Hardware
Instruction set MIPS32
Sub Instruction Set MIPS32 24K/E series
Bootloader U-Boot
Target ramips
System-On-Chip Ralink RT3052
CPU MHz 384
Flash MB 4
RAM MB 32
Network
Ethernet 100M ports 5
Ethernet Gbit ports -
Switch
Modem No
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz -
WLAN Hardware
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports -
SATA ports -
Serial Yes
JTAG Yes
Comments - USB & SATA ports
Misc
LED count
Button count
Power supply
Links
Forum Topic URL
WikiDevi URL https://wikidevi.com/wiki/EnGenius_ESR-9753
OEM device homepage URL http://www.engeniustech.com/products/discontinued-eol/consumer/150-mbps-wireless-router.html
Firmware OEM Stock URL
Firmware OpenWrt Install URL https://downloads.openwrt.org/chaos_calmer/15.05/ramips/rt305x/openwrt-15.05-ramips-rt305x-esr-9753-initramfs-uImage.bin
Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/chaos_calmer/15.05/ramips/rt305x/openwrt-15.05-ramips-rt305x-esr-9753-squashfs-sysupgrade.bin
Edit the underlying data View/Edit data

Serial

port.serial general information about the serial port, serial port cable, etc.

Serial connection parameters 57600, 8N1

OpenWrt bootlog

[ 0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 Fri Sep 4 19:34:21 CEST 2015 [ 0.000000] SoC Type: Ralink RT3052 id:1 rev:2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is Senao / EnGenius ESR-9753 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff] [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 802d22b0, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8192 pages, LIFO batch:0 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=0000142f [ 0.000000] Readback ErrCtl register=0000142f [ 0.000000] Memory: 29080K/32768K available (2543K kernel code, 120K rwdata, 312K rodata, 152K init, 186K bss, 3688K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 384MHz [ 0.000000] clocksource_of_init: no matching clocksources found [ 0.070000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100000] pinctrl core: initialized pinctrl subsystem [ 0.110000] NET: Registered protocol family 16 [ 0.120000] rt2880-pinmux pinctrl: try to register 52 pins ... [ 0.120000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux [ 0.120000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux [ 0.120000] pinctrl core: add 7 pinmux maps [ 0.120000] rt2880-pinmux pinctrl: found group selector 7 for sdram [ 0.120000] rt2880-pinmux pinctrl: found group selector 1 for spi [ 0.120000] rt2880-pinmux pinctrl: found group selector 0 for i2c [ 0.120000] rt2880-pinmux pinctrl: found group selector 4 for jtag [ 0.120000] rt2880-pinmux pinctrl: found group selector 6 for rgmii [ 0.120000] rt2880-pinmux pinctrl: found group selector 5 for mdio [ 0.120000] rt2880-pinmux pinctrl: found group selector 2 for uartf [ 0.120000] rt2880-pinmux pinctrl: request pin 24 (io24) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 25 (io25) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 26 (io26) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 27 (io27) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 28 (io28) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 29 (io29) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 30 (io30) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 31 (io31) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 32 (io32) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 33 (io33) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 34 (io34) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 35 (io35) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 36 (io36) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 37 (io37) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 38 (io38) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 39 (io39) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 3 (io3) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 4 (io4) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 5 (io5) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 6 (io6) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 1 (io1) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 2 (io2) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 17 (io17) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 18 (io18) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 19 (io19) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 20 (io20) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 21 (io21) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 40 (io40) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 41 (io41) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 42 (io42) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 43 (io43) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 44 (io44) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 45 (io45) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 46 (io46) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 47 (io47) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 48 (io48) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 49 (io49) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 50 (io50) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 51 (io51) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 22 (io22) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 23 (io23) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 7 (io7) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 8 (io8) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 9 (io9) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 10 (io10) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 11 (io11) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 12 (io12) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 13 (io13) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl [ 0.120000] rt2880-pinmux pinctrl: failed to lookup the sleep state [ 0.130000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.140000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.150000] Switched to clocksource MIPS [ 0.160000] NET: Registered protocol family 2 [ 0.170000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.180000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.190000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.210000] TCP: reno registered [ 0.210000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.220000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.240000] NET: Registered protocol family 1 [ 0.250000] rt-timer 10000100.timer: maximum frequency is 7812Hz [ 0.260000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT [ 0.260000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.370000] msgmni has been set to 56 [ 0.380000] io scheduler noop registered [ 0.380000] io scheduler deadline registered (default) [ 0.390000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.410000] serial8250 serial8250: no of_node; not parsing pinctrl DT [ 0.410000] pinctrl core: add 1 pinmux maps [ 0.410000] rt2880-pinmux pinctrl: found group selector 3 for uartlite [ 0.410000] rt2880-pinmux pinctrl: request pin 15 (io15) for 10000c00.uartlite [ 0.410000] rt2880-pinmux pinctrl: request pin 16 (io16) for 10000c00.uartlite [ 0.410000] console [ttyS0] disabled [ 0.420000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 8000000) is a 16550A [ 0.440000] console [ttyS0] enabled [ 0.450000] bootconsole [early0] disabled [ 0.470000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a7 [ 0.490000] 1f000000.cfi: Found an alias at 0x400000 for the chip at 0x0 [ 0.490000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.500000] Amd/Fujitsu Extended Query version 1.1. [ 0.510000] 1f000000.cfi: Swapping erase regions for top-boot CFI table. [ 0.530000] number of CFI chips: 1 [ 0.550000] 4 ofpart partitions found on MTD device 1f000000.cfi [ 0.560000] Creating 4 MTD partitions on "1f000000.cfi": [ 0.570000] 0x000000000000-0x000000030000 : "u-boot" [ 0.580000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.590000] 0x000000040000-0x000000050000 : "factory" [ 0.610000] 0x000000050000-0x000000400000 : "firmware" [ 0.620000] 2 uimage-fw partitions found on MTD device firmware [ 0.630000] 0x000000050000-0x0000001508bf : "kernel" [ 0.640000] 0x0000001508bf-0x000000400000 : "rootfs" [ 0.650000] mtd: device 5 (rootfs) set to be root filesystem [ 0.670000] 1 squashfs-split partitions found on MTD device rootfs [ 0.680000] 0x000000370000-0x000000400000 : "rootfs_data" [ 0.700000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.710000] rt2880_wdt 10000120.watchdog: Initialized [ 0.720000] TCP: cubic registered [ 0.730000] NET: Registered protocol family 17 [ 0.740000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.770000] Bridge firewalling registered [ 0.770000] 8021q: 802.1Q VLAN Support v1.8 [ 0.810000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 0.820000] Freeing unused kernel memory: 152K (802ea000 - 80310000) [ 0.930000] rt305x-esw 10110000.esw: link changed 0x04 [ 2.010000] init: Console is alive [ 2.020000] init: - watchdog - [ 3.390000] usbcore: registered new interface driver usbfs [ 3.400000] usbcore: registered new interface driver hub [ 3.410000] usbcore: registered new device driver usb [ 3.430000] rt2880-pinmux pinctrl: request pin 10 (io10) for pio:10 [ 3.430000] rt2880-pinmux pinctrl: request pin 0 (io0) for pio:0 [ 3.430000] rt2880-pinmux pinctrl: request pin 8 (io8) for pio:8 [ 3.430000] rt2880-pinmux pinctrl: request pin 14 (io14) for pio:14 [ 4.030000] init: - preinit - [ 4.990000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 5.150000] random: procd urandom read with 7 bits of entropy available [ 8.580000] jffs2: notice: (291) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 8.610000] mount_root: switching to jffs2 overlay [ 8.660000] procd: - early - [ 8.670000] procd: - watchdog - [ 9.580000] procd: - ubus - [ 10.590000] procd: - init - [ 11.790000] NET: Registered protocol family 10 [ 11.810000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.850000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 11.860000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 11.880000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.910000] nf_conntrack version 0.5.0 (456 buckets, 1824 max) [ 11.980000] xt_time: kernel timezone is -0000 [ 12.030000] cfg80211: Calling CRDA to update world regulatory domain [ 12.060000] cfg80211: World regulatory domain updated: [ 12.070000] cfg80211: DFS Master region: unset [ 12.080000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 12.090000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 12.110000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 12.130000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 12.140000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 12.160000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 12.180000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 12.190000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 12.210000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 12.320000] PPP generic driver version 2.4.2 [ 12.340000] NET: Registered protocol family 24 [ 12.390000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected [ 12.400000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected [ 12.420000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 22.450000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 22.490000] device eth0.1 entered promiscuous mode [ 22.500000] device eth0 entered promiscuous mode


Tags

toh/engenius/engenius_esr9753.txt · Last modified: 2015/12/14 19:50 by tmomas