Differences
This shows you the differences between two versions of the page.
|
toh:gigaset:sl2-141-i [2012/09/30 21:49] doc_i |
toh:gigaset:sl2-141-i [2012/11/18 22:51] (current) habee |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Siemens SL2-141-i ====== | ====== Siemens SL2-141-i ====== | ||
| - | Siemens SL2-141-i ADSL2+ Router with Wi-Fi 802.11g 54Mbps. It is most similar to the [[toh:netcomm:nb6plus4w|RTA1025W]] from Dynalink | + | Siemens SL2-141-i ADSL2+ Router with Wi-Fi 802.11g 54Mbps. It is most similar to the [[toh:netcomm:nb6plus4w|RTA1025W]] from Dynalink After changing the Board ID you can use these firmwares. |
| ==== Supported Versions ==== | ==== Supported Versions ==== | ||
| Line 6: | Line 6: | ||
| See also https://dev.openwrt.org/ticket/6920 | See also https://dev.openwrt.org/ticket/6920 | ||
| + | |||
| + | But you can change the Board-ID using cfe-environment and serial console, then you can use the RTA1025W-Builds. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| ==== Hardware Highlights ==== | ==== Hardware Highlights ==== | ||
| Line 67: | Line 74: | ||
| </code> | </code> | ||
| + | |||
| + | === Changing the Board-ID to use Dynalink RTA1025W-Firmwares === | ||
| + | |||
| + | Connect to the board using a serial console cable, boot the device and | ||
| + | stop it booting by pressing space to get on the cfe-prompt: | ||
| + | |||
| + | <code>CFE version 1.0.37-6.8.5 for BCM96348 (32bit,SP,BE) | ||
| + | Build Date: Tue Jan 2 19:42:28 CST 2007 (michaelc) | ||
| + | |||
| + | Boot Address 0xbfc00000 | ||
| + | |||
| + | Flash Config: CS0(1fc00009,1f),Base(bfc00000),Size(4MB) | ||
| + | Ethernet Switch Mode 00000000 | ||
| + | found@block 8 | ||
| + | |||
| + | Board IP address : 192.168.1.1 | ||
| + | Host IP address : 192.168.1.2 | ||
| + | Gateway IP address : | ||
| + | Run from flash/host (f/h) : f | ||
| + | Default host run file name : | ||
| + | Default host flash file name : bcmModelName_fs_kernel | ||
| + | Boot delay (0-9 seconds) : 1 | ||
| + | Board Id Name : RTA1025BW_16 | ||
| + | Psi size in KB : 24 | ||
| + | Number of MAC Addresses (1-32) : 4 | ||
| + | Ethernet MAC Address : 00:16:e3:xx:xx:xx | ||
| + | Serial Number : | ||
| + | Memory size in MB : 16 | ||
| + | CMT Thread Number : 0 | ||
| + | |||
| + | ==== Press space key to stop auto run (1 seconds) ==== | ||
| + | Auto run second count down(before hit space key):</code> | ||
| + | |||
| + | At cfe-prompt type 'b' followed by enter: | ||
| + | |||
| + | <code>CFE> b | ||
| + | Press: <enter> to use current value | ||
| + | |||
| + | Board Id Name (A-Q) | ||
| + | RTA1046VW -------- A | ||
| + | RTA1046BVW -------- B | ||
| + | RTA1052VW -------- C | ||
| + | RTA1052BVW -------- D | ||
| + | RTA1052V -------- E | ||
| + | RTA1052BV -------- F | ||
| + | V2091_BB -------- G | ||
| + | V2091 -------- H | ||
| + | V2090 -------- I | ||
| + | V2110 -------- J | ||
| + | V2500V_BB -------- K | ||
| + | RTA1025W_16 -------- L | ||
| + | RTA1025BW_16 -------- M | ||
| + | RTA1505W_16 -------- N | ||
| + | RTA1505BW_16 -------- O | ||
| + | RTA1046VW_32M -------- P | ||
| + | RTA1046BVW_32M -------- Q :[M]: L | ||
| + | Number of MAC Addresses (1-32) :[4]: | ||
| + | Ethernet MAC Address :[00:16:e3:xx:xx:xx]: | ||
| + | Serial Number :[]: | ||
| + | |||
| + | Save and Exit (y/n):y | ||
| + | |||
| + | Save your new configuration to nvram........done | ||
| + | |||
| + | Press any key to reset the board: </code> | ||
| + | |||
| + | You have to choose 'L' instead of the predefined 'M' to switch to Board-ID RTA1025W_16! | ||
| + | |||
| + | After saving and reboot you can flash any RTA1025W_16-based openwrt-Firmware. | ||
| + | |||
| === Original Source Code === | === Original Source Code === | ||
toh/gigaset/sl2-141-i.1349034544.txt.bz2 · Last modified: 2012/09/30 21:49 by doc_i