The HG520v is currently not supported!

You must set your TCP/IP v4 protocol to:

1. IP: 192.168.1.2
2. Netmask: 255.255.255.0
3. Gateway: 192.168.1.1
4. DNS: (optional, can be blank).

Then:

1. Power off the router.
2. Press reset button near the antenna.
3. Keep it pressed while powering up during ~20+ seconds.
4. Acces to http://192.168.1.1 and upload binary file.
5. Wait until router reboots.

→ port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Photo of PCB with markings

Read: System configuration: Leds to configure the leds

→ hardware.button on howto use and configure the hardware button(s).

CFE version cfe.d060.5002 for BCM96358 (32bit,SP,BE) Build Date: Èý 10ÔÂ 18 13:16:46 CST 2006 (yuyouqing42304) Copyright (C) 2006 Huawei Technologies Co. Ltd. Boot Address 0xbfc00000 Initializing Arena. Initializing Devices. Parallel flash device: name AM29LV320MT, id 0x2201, size 4096KB setBoardIdName is forced HW6358GW_B. CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz Total memory: 33554432 bytes (32MB) Total memory used by CFE: 0x80401000 - 0x80528770 (1210224) Initialized Data: 0x8041DA90 - 0x8041FE30 (9120) BSS Area: 0x8041FE30 - 0x80426770 (26944) Local Heap: 0x80426770 - 0x80526770 (1048576) Stack Area: 0x80526770 - 0x80528770 (8192) Text (code) segment: 0x80401000 - 0x8041DA90 (117392) Boot area (physical): 0x00529000 - 0x00569000 Relocation Factor: I:00000000 - D:00000000 Board IP address : 192.168.1.1 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id Name : HW6358GW_B Psi size in KB : 64 Number of MAC Addresses (1-32) : 11 Base MAC Address : XX:XX:XX:XX:XX:XX Ethernet PHY Type : Internal Memory size in MB : 32 CMT Thread Number : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Code Address: 0x80010000, Entry Address: 0x801bf018 Decompression OK! Entry at 0x801bf018 Starting program at 0x801bf018 Linux version 2.6.8.1 (root@localhost) (gcc version 3.4.2) #1 Fri Nov 21 15:49:4 3 CST 2008 Parallel flash device: name AM29LV320MT, id 0x2201, size 4096KB Total Flash size: 4096K with 71 sectors Board id is set HW6358GW_B HW6358GW_B prom init CPU revision is: 0002a010 mpi: No Card is in the PCMCIA slot Determined physical RAM map: memory: 01ff1920 @ 00000000 (usable) On node 0 totalpages: 8177 DMA zone: 8177 pages, LIFO batch:1 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=31:0 ro noinitrd brcm mips: enabling icache and dcache... Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 16kB 2-way, linesize 16 bytes. PID hash table entries: 128 (order 7: 1024 bytes) Using 150.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 30340k/32708k available (1503k kernel code, 2348k reserved, 217k data, 7 2k init, 0k highmem) Calibrating delay loop... 299.00 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Checking for 'wait' instruction... unavailable. NET: Registered protocol family 16 Can't analyze prologue code at 8018647c Initializing Cryptographic API PPP generic driver version 2.4.2 NET: Registered protocol family 24 Using noop io scheduler bcm963xx_mtd driver v1.0 brcmboard: brcm_board_init entry SES: Button Interrupt 0x3 is enabled bcm963xx_serial driver v2.0 u32 classifier NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered NET: Registered protocol family 8 NET: Registered protocol family 20 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 72k freed init started: BusyBox v1.00 (2008.11.21-07:54+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.00 (2008.11.21-07:54+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... atmapi: module license 'Proprietary' taints kernel. blaadd: blaa_detect entry Broadcom BCMPROCFS v1.0 initialized Broadcom BCM6358A1 Ethernet Network Device v0.3 Nov 21 2008 15:48:15 Config Ethernet Switch Through MDIO Pseudo PHY Interface dgasp: kerSysRegisterDyingGaspHandler: eth0 registered ======oh oh dev name is eth0.0 ======oh oh dev name is eth0.1 eth0: MAC Address: XX:XX:XX:XX:XX:XX PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:01.0 (0004 -> 0006) wl: srom not detected, using main memory mapped srom info (wombo board) wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board) wl0 MAC Address: XX:XX:XX:XX:XX:XX wl0: Broadcom BCM4318 802.11 Wireless Controller 3.131.35.0.cpe2.3 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered wlctl: xmlGetMxpktAttr(attrName maxpacket, attrValue 0) ip is 192.168.1.1mask is 255.255.255.0, ipbegin is 192.168.1.33, ipend is 19 2.168.1.254 wlctl: xmlGetMxpktAttr(attrName maxpacket, attrValue 0) bcmSetAtmConfigMode Current mode is:atmctl configmode ptmprotocol adslctl: not found adslctl: not found ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (255 buckets, 0 max) - 368 bytes per conntrack ip_conntrack_pptp version 2.1 loaded ip_nat_pptp version 2.0 loaded ip_nat_irc: Unknown symbol needs_ip_conntrack_irc insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_irc .ko': Success (2): Success VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_transfer.c,42: BCM6505 reset and ADSL/VDSL mode selection. =========pchr is:atmctl traffic atm atmctl intf --settype 0 utopia level2 VDSLCTL FAILURE at bcm_socket.c,177: could not connect. RELAY INFO at bcm_socket.c,199: Try socket connection for 90 seconds. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_transfer.c,47: hpi_Init. HSTMGR INFO at bcm_transfer.c,51: utopia_Init. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_boot.c,95: Booting the BCM17f7 device 0. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. VDSLCTL FAILURE at bcm_socket.c,177: could not connect. HSTMGR INFO at bcm_transfer.c,168: Setting PLL speed. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[3] = 0x8a. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[2] = 0x3e. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[VDSLCTL FAILURE at bcm_soc ket.c,177: could not connect. 1] = 0x21. HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[0] = 0x13. HSTMGR INFO at bcm_transfer.c,186: Wait for PLL lock. HSTMGR INFO at bcm_transfer.c,197: PLL locked OK. HSTMGR INFO at bcm_transfer.c,204: Select PLL. HSTMGR INFO at bcm_transfer.c,212: PLL Active (assumed). HSTMGR INFO at bcm_transfer.c,132: 6510 Magic Register = 0x03. Loading image .. done HSTMGR INFO at bcm_boot.c,245: Boot firmware release: 4.0.0. HSTMGR INFO at bcm_boot.c,248: HMI download protocol: 1.0. Loading target image through HMI: 0%  0% VDSLCTL FAILURE at bcm_socket.c,177: could not connect. 0%  0%  0%  0%  0%  0%  1%  1%  1%  1%  1%  1%  1%  2%  2%  2%  2%  2%  2%  2%  3%  3%  3%  3%  3%  3%  3%  4%  4%  4%  4%  4%  4%  5%  5%  5%  5%  5%  5%  5%  6%  6%  6%  6%  6%  6%  6%  7%  7%  7%  7%  7%  7%  7%  8%  8%  8%  8%  8%  8%  8%  9%  9%  9%  9%  9%  9% 10% 10% 10% 10% 10% 10% 10% 11% 11% 11% 11% 11% 11% 11% 12% 12% 12% 12% 12% 12% 12% 13% 13% 13% 13% 13% 13% 14% 14% 14% 14% 14% 14% 14% 15% 15% 15% 15% 15% 15% 15% 16% 16% 16% 16% 16% 16% 16% 17% 17% 17% 17% 17% 17% 17% 18% 18% 18% 18% 18% 18% 19% 19% 19% 19% 19% 19% 19% 20% 20% 20% 20% 20% 20% 20% 21% 21% 21% 21% 21% 21% 21% 22% 22% 22% 22% 22% 22% 22% 23% 23% 23% 23% 23% 23% 24% 24% 24% 24% 24% 24% 24% 25% 25% 25% 25% 25% 25% 25% 26% 26% 26% 26% 26% 26% 26% 27% 27% 27% 27% 27% 27% 28% 28% 28% 28% 28% 28% 28% 29% 29% 29% 29% 29% 29% 29% 30% 30% 30% 30% 30% 30% 30% 31% 31% 31% 31% 31% 31% 31% 32% 32% 32% 32% 32% 32% 33% 33% 33% 33% 33% 33% 33% 34% 34% 34% 34% 34% 34% 34% 35% 35% 35% 35% 35% 35% 35% 36% 36% 36% 36% 36% 36% 36% 37% 37% 37% 37% 37% 37% 38% 38% 38% 38% 38% VDSLCTL FAILURE at bcm_socket.c,177: could not connect. 38% 38% 39% 39% 39% 39% 39% 39% 39% 40% 40% 40% 40% 40% 40% 40% 41% 41% 41% 41% 41% 41% 42% 42% 42% 42% 42% 42% 42% 43% 43% 43% 43% 43% 43% 43% 44% 44% 44% 44% 44% 44% 44% 45% 45% 45% 45% 45% 45% 45% 46% 46% 46% 46% 46% 46% 47% 47% 47% 47% 47% 47% 47% 48% 48% 48% 48% 48% 48% 48% 49% 49% 49% 49% 49% 49% 49% 50% 50% 50% 50% 50% 50% 51% 51% 51% 51% 51% 51% 51% 52% 52% 52% 52% 52% 52% 52% 53% 53% 53% 53% 53% 53% 53% 54% 54% 54% 54% 54% 54% 54% 55% 55% 55% 55% 55% 55% 56% 56% 56% 56% 56% 56% 56% 57% 57% 57% 57% 57% 57% 57% 58% 58% 58% 58% 58% 58% 58% 59% 59% 59% 59% 59% 59% 59% 60% 60% 60% 60% 60% 60% 61% 61% 61% 61% 61% 61% 61% 62% 62% 62% 62% 62% 62% 62% 63% 63% 63% 63% 63% 63% 63% 64% 64% 64% 64% 64% 64% 65% 65% 65% 65% 65% 65% 65% 66% 66% 66% 66% 66% 66% 66% 67% 67% 67% 67% 67% 67% 67% 68% 68% 68% 68% 68% 68% 68% 69% 69% 69% 69% 69% 69% 70% 70% 70% 70% 70% 70% 70% 71% 71% 71% 71% 71% 71% 71% 72% 72% 72% 72% 72% 72% 72% 73% 73% 73% 73% 73% 73% 73% 74% 74% 74% 74% 74% 74% 75% 75% 75% 75% 75% 75% 75% 76% 76% 76% 76% 76% 76% 76% 77% 77% VDSLCTL FAILURE at bcm_socket.c,177: could not connect. 77% 77% 77% 77% 77% 78% 78% 78% 78% 78% 78% 79% 79% 79% 79% 79% 79% 79% 80% 80% 80% 80% 80% 80% 80% 81% 81% 81% 81% 81% 81% 81% 82% 82% 82% 82% 82% 82% 82% 83% 83% 83% 83% 83% 83% 84% 84% 84% 84% 84% 84% 84% 85% 85% 85% 85% 85% 85% 85% 86% 86% 86% 86% 86% 86% 86% 87% 87% 87% 87% 87% 87% 88% 88% 88% 88% 88% 88% 88% 89% 89% 89% 89% 89% 89% 89% 90% 90% 90% 90% 90% 90% 90% 91% 91% 91% 91% 91% 91% 91% 92% 92% 92% 92% 92% 92% 93% 93% 93% 93% 93% 93% 93% 94% 94% 94% 94% 94% 94% 94% 95% 95% 95% 95% 95% 95% 95% 96% 96% 96% 96% 96% 96% 96% 97% 97% 97% 97% 97% 97% 98% 98% 98% 98% 98% 98% 98% 99% 99% 99% 99% 99% 99% 99% done HSTMGR INFO at bcm_hostMgr.c,94: Interrupt polling enabled. bind now the file descriptor from IP 0.0.0.0, my port 57665. vdslctl: Started successfully RELAY INFO at bcm_socket.c,224: Connected successfully (fd: 6). =========pchr is:atmctl traffic atm ==> Bcm963xx VDSL Software Version: 09.02.07, 2006-11-15 <== ==> Bcm963xx Software Version: V100R001C02B066_V_SP3 <== atmctl intf --settype 0 utopia level2 ========bcm63xx_enet_open dev->name is:eth0 device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state pvc2684ctl_main trafficmode:2 pvc2684d_main:2 setIndexName1 pvc2684d: Interface "nas_0_32_0" created sucessfully AttachVcc g_nPtmConfig:2 setIndexName1 pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC device nas_0_32_0 entered promiscuous mode br0: port 2(nas_0_32_0) entering learning state br0: topology change detected, propagating br0: port 2(nas_0_32_0) entering forwarding state device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state eth0.2: MAC Address: XX:XX:XX:XX:XX:XX eth0.3: MAC Address: XX:XX:XX:XX:XX:XX eth0.4: MAC Address: XX:XX:XX:XX:XX:XX eth0.5: MAC Address: XX:XX:XX:XX:XX:XX device eth0.2 entered promiscuous mode br0: port 1(eth0.2) entering learning state br0: topology change detected, propagating br0: port 1(eth0.2) entering forwarding state device eth0.3 entered promiscuous mode br0: port 3(eth0.3) entering learning state br0: topology change detected, propagating br0: port 3(eth0.3) entering forwarding state device eth0.4 entered promiscuous mode br0: port 4(eth0.4) entering learning state br0: topology change detected, propagating br0: port 4(eth0.4) entering forwarding state device eth0.5 entered promiscuous mode br0: port 5(eth0.5) entering learning state br0: topology change detected, propagating br0: port 5(eth0.5) entering forwarding state In webmain, setup wlan br0: port 1(eth0.2) entering disabled state br0: port 3(eth0.3) entering disabled state br0: port 4(eth0.4) entering disabled state br0: port 5(eth0.5) entering disabled state Login:

[ 0.000000] Linux version 3.6.11 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Wed Jan 9 20:07:04 CET 2013 [ 0.000000] Detected Broadcom 0x6358 CPU revision a1 [ 0.000000] CPU frequency is 300 MHz [ 0.000000] 32MB of RAM installed [ 0.000000] registering 40 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xbfc00000 [ 0.000000] board_bcm963xx: CFE version: 100.48.54-48.46 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: HW6358GW_B [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 802a8db0, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8128 pages, LIFO batch:0 [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 28356k/32768k available (2260k kernel code, 4412k reserved, 400k data, 1072k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.032000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 512 [ 0.048000] NET: Registered protocol family 16 [ 0.060000] registering PCI controller with io_map_base unset [ 0.080000] bio: create slab at 0 [ 0.088000] PCI host bridge to bus 0000:00 [ 0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.096000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.100000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.104000] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff] [ 0.104000] pci 0000:00:01.0: [14e4:4318] type 00 class 0x028000 [ 0.104000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00001fff] [ 0.116000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.116000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff] [ 0.120000] Switching to clocksource MIPS [ 0.132000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.136000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64 [ 0.160000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x00 [ 0.168000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243) [ 0.168000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243) [ 0.168000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243) [ 0.168000] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243) [ 0.208000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.216000] NET: Registered protocol family 2 [ 0.224000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.232000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.236000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.244000] TCP: reno registered [ 0.248000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.252000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] NET: Registered protocol family 1 [ 0.264000] PCI: CLS 0 bytes, default 16 [ 2.744000] audit: initializing netlink socket (disabled) [ 2.748000] type=2000 audit(2.748:1): initialized [ 2.756000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.760000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.772000] msgmni has been set to 55 [ 2.776000] io scheduler noop registered [ 2.780000] io scheduler deadline registered (default) [ 2.788000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart [ 2.796000] console [ttyS0] enabled, bootconsole disabled [ 2.812000] physmap platform flash device: 00400000 at 1fc00000 [ 2.816000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a01 [ 2.828000] Amd/Fujitsu Extended Query Table at 0x0040 [ 2.832000] Amd/Fujitsu Extended Query version 1.3. [ 2.840000] physmap-flash.0: Swapping erase regions for top-boot CFI table. [ 2.844000] number of CFI chips: 1 [ 2.848000] bcm63xxpart: CFE boot tag found with version 6 and board type HW6358GW_B [ 2.856000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 2.864000] bcm63xxpart: Partition 1 is rootfs offset 10100 and length 2bb000 [ 2.872000] bcm63xxpart: Partition 2 is kernel offset 2cb100 and length 8aac4 [ 2.880000] bcm63xxpart: Partition 3 is nvram offset 3f0000 and length 10000 [ 2.884000] bcm63xxpart: Partition 4 is linux offset 10000 and length 3e0000 [ 2.892000] bcm63xxpart: Spare partition is offset 360000 and length 90000 [ 2.900000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 [ 2.908000] Creating 5 MTD partitions on "physmap-flash.0": [ 2.912000] 0x000000000000-0x000000010000 : "CFE" [ 2.920000] 0x000000010100-0x0000002cb100 : "rootfs" [ 2.928000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 2.944000] mtd: partition "rootfs" set to be root filesystem [ 2.948000] split_squashfs: no squashfs found in "physmap-flash.0" [ 2.956000] 0x0000002cb100-0x000000355bc4 : "kernel" [ 2.960000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 2.976000] 0x0000003f0000-0x000000400000 : "nvram" [ 2.988000] 0x000000010000-0x0000003f0000 : "linux" [ 3.004000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 3.012000] TCP: cubic registered [ 3.016000] NET: Registered protocol family 17 [ 3.020000] 8021q: 802.1Q VLAN Support v1.8 [ 3.044000] Freeing unused kernel memory: 1072k freed [ 4.132000] roboswitch: Probing device 'eth0' [ 4.136000] roboswitch: found a 5325! It's a 5350. at eth0 [ 5.192000] There is already a switch registered on the device 'eth0' [ 10.164000] There is already a switch registered on the device 'eth0' [ 10.192000] Button Hotplug driver version 0.4.1 [ 10.240000] PPP generic driver version 2.4.2 [ 10.332000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.536000] NET: Registered protocol family 24 [ 10.568000] nf_conntrack version 0.5.0 (459 buckets, 1836 max) [ 10.924000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542) v0.1.2 [ 15.640000] eth0: link forced UP - 100/full - flow control off/off [ 62.056000] eth0: link forced UP - 100/full - flow control off/off [ 62.068000] device eth0 entered promiscuous mode [ 62.076000] br-lan: port 1(eth0) entered forwarding state [ 62.080000] br-lan: port 1(eth0) entered forwarding state [ 64.084000] br-lan: port 1(eth0) entered forwarding state