Differences

This shows you the differences between two versions of the page.

toh:huawei:hg520v [2013/01/11 15:11] (current)
Line 1: Line 1:
 +====== Huawei HG520v ======
 +**<color red>The HG520v is currently not supported!</color>**
 +===== Installation =====
 +==== Flashing ANY Firmware ====
 +You must set your TCP/IP v4 protocol to:
 +  - IP: 192.168.1.2
 +  - Netmask: 255.255.255.0
 +  - Gateway: 192.168.1.1
 +  - DNS: (optional, can be blank).
 +Then:
 +  - Power off the router.
 +  - Press reset button near the antenna.
 +  - Keep it pressed while powering up during ~20+ seconds.
 +  - Acces to http://192.168.1.1 and upload binary file.
 +  - Wait until router reboots.
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] |
 +| **Vendor:**          | [[wp>Broadcom]] |
 +| **[[doc:techref:Bootloader]]:**    | [[doc:techref:bootloader:CFE]] |
 +| Bootloader version | vd060.5002 |
 +| **[[doc:hardware:soc|System-On-Chip]]:**  | Broadcom BCM6359 |
 +| **vDSL AFE:**  | Broadcom BCM6505 |
 +| **vDSL Tranceiver:**  | Broadcom BCM6314 |
 +| **[[doc:hardware:cpu|CPU]]/Speed**        | BMIPS32 / 300 MHz |
 +| **Board ID:**      | HW6358GW_B  |
 +| **Flash-Chip:**      | AM29LV320MT |
 +| Flash size | 4 MiB |
 +| RAM | 32 MiB |
 +| Wireless | BCM4318 (14e4:4318) 802.11b/g |
 +| Wireless power | ? mW |
 +| **Ethernet:**        | Broadcom  {{:toh:bcm5325_datasheet.pdf|BCM5325}} w/ vlan support [[doc:uci:network#swconfig]] |
 +| USB | ? |
 +| Power adapter | ? |
 +| Power margin | ? |
 +| Antenna | 2x |
 +| Antenna gain | ? dBi |
 +| **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] |
 +| **[[doc:hardware:port.jtag|JTAG]]:**            | [[#JTAG|?]]  |
 +
 +==== Photos ====
 +=== Router ===
 +{{:toh:huawei:hg520v_router.jpg?500x300|}}
 +
 +=== Board Front ===
 +{{:toh:huawei:hg520v_board_up.jpg?500x300|}}
 +
 +=== vDSL Chips ===
 +{{:toh:huawei:hg520v_vdsl_chips.jpg?500x300|}}
 +
 +==== JTAG ====
 +-> [[doc:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +N/A
 +
 +==== Serial ====
 +-> [[doc:hardware:port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:
 +
 +{{:toh:huawei:hg520v_board_serial.jpg?500x300|}}
 +
 +**Photo of PCB with markings**
 +
 +===== GPIO =====
 +==== LEDs ====
 +Read: [[doc:uci:system#leds|System configuration: Leds]] to configure the leds
 +^ Pin ^ Event ^ Active ^
 +| ? | power (green) | ? |
 +| ? | dsl (green) | ? |
 +| 32 | inet (green) | Low |
 +
 +==== Buttons ====
 +-> [[doc:howto:hardware.button]] on howto use and configure the hardware button(s).
 +^ Pin ^ Event ^ Active ^
 +| ? | Reset | ? |
 +
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +<HTML>
 +<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
 +<code>CFE version cfe.d060.5002 for BCM96358 (32bit,SP,BE)
 +Build Date: Èý 10ÔÂ 18 13:16:46 CST 2006 (yuyouqing42304)
 +Copyright (C) 2006 Huawei Technologies Co. Ltd.
 +
 +Boot Address 0xbfc00000
 +
 +Initializing Arena.
 +Initializing Devices.
 +Parallel flash device: name AM29LV320MT, id 0x2201, size 4096KB
 +setBoardIdName is forced HW6358GW_B.
 +CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
 +Total memory: 33554432 bytes (32MB)
 +
 +Total memory used by CFE:  0x80401000 - 0x80528770 (1210224)
 +Initialized Data:          0x8041DA90 - 0x8041FE30 (9120)
 +BSS Area:                  0x8041FE30 - 0x80426770 (26944)
 +Local Heap:                0x80426770 - 0x80526770 (1048576)
 +Stack Area:                0x80526770 - 0x80528770 (8192)
 +Text (code) segment:      0x80401000 - 0x8041DA90 (117392)
 +Boot area (physical):      0x00529000 - 0x00569000
 +Relocation Factor:        I:00000000 - D:00000000
 +
 +Board IP address                  : 192.168.1.1 
 +Host IP address                  : 192.168.1.100 
 +Gateway IP address                : 
 +Run from flash/host (f/h)        : f 
 +Default host run file name        : vmlinux 
 +Default host flash file name      : bcm963xx_fs_kernel 
 +Boot delay (0-9 seconds)          : 1 
 +Board Id Name                    : HW6358GW_B 
 +Psi size in KB                    : 64
 +Number of MAC Addresses (1-32)    : 11 
 +Base MAC Address                  : XX:XX:XX:XX:XX:XX
 +Ethernet PHY Type                : Internal
 +Memory size in MB                : 32
 +CMT Thread Number                : 0
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 110
 +Code Address: 0x80010000, Entry Address: 0x801bf018
 +Decompression OK!
 +Entry at 0x801bf018
 +Starting program at 0x801bf018
 +Linux version 2.6.8.1 (root@localhost) (gcc version 3.4.2) #1 Fri Nov 21 15:49:4
 +3 CST 2008
 +Parallel flash device: name AM29LV320MT, id 0x2201, size 4096KB
 +Total Flash size: 4096K with 71 sectors
 +
 + Board id is set HW6358GW_B
 +HW6358GW_B prom init
 +CPU revision is: 0002a010
 +mpi: No Card is in the PCMCIA slot
 +Determined physical RAM map:
 + memory: 01ff1920 @ 00000000 (usable)
 +On node 0 totalpages: 8177
 +  DMA zone: 8177 pages, LIFO batch:1
 +  Normal zone: 0 pages, LIFO batch:1
 +  HighMem zone: 0 pages, LIFO batch:1
 +Built 1 zonelists
 +Kernel command line: root=31:0 ro noinitrd
 +brcm mips: enabling icache and dcache...
 +Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
 +Primary data cache 16kB 2-way, linesize 16 bytes.
 +PID hash table entries: 128 (order 7: 1024 bytes)
 +Using 150.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 30340k/32708k available (1503k kernel code, 2348k reserved, 217k data, 7
 +2k init, 0k highmem)
 +Calibrating delay loop... 299.00 BogoMIPS
 +Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
 +Checking for 'wait' instruction...  unavailable.
 +NET: Registered protocol family 16
 +Can't analyze prologue code at 8018647c
 +Initializing Cryptographic API
 +PPP generic driver version 2.4.2
 +NET: Registered protocol family 24
 +Using noop io scheduler
 +bcm963xx_mtd driver v1.0
 +brcmboard: brcm_board_init entry
 +SES: Button Interrupt 0x3 is enabled
 +bcm963xx_serial driver v2.0
 +u32 classifier
 +NET: Registered protocol family 2
 +IP: routing cache hash table of 512 buckets, 4Kbytes
 +TCP: Hash tables configured (established 2048 bind 4096)
 +Initializing IPsec netlink socket
 +NET: Registered protocol family 1
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +Ebtables v2.0 registered
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing unused kernel memory: 72k freed
 +init started:  BusyBox v1.00 (2008.11.21-07:54+0000) multi-call binary
 +Algorithmics/MIPS FPU Emulator v1.5
 +
 +
 +BusyBox v1.00 (2008.11.21-07:54+0000) Built-in shell (msh)
 +Enter 'help' for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules...
 +
 +atmapi: module license 'Proprietary' taints kernel.
 +blaadd: blaa_detect entry
 +Broadcom BCMPROCFS v1.0 initialized
 +Broadcom BCM6358A1 Ethernet Network Device v0.3 Nov 21 2008 15:48:15
 +Config Ethernet Switch Through MDIO Pseudo PHY Interface
 +dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
 +======oh oh dev name is eth0.0
 +======oh oh dev name is eth0.1
 +eth0: MAC Address: XX:XX:XX:XX:XX:XX
 +PCI: Setting latency timer of device 0000:00:01.0 to 64
 +PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
 +wl: srom not detected, using main memory mapped srom info (wombo board)
 +wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board)
 +wl0 MAC Address: XX:XX:XX:XX:XX:XX
 +wl0: Broadcom BCM4318 802.11 Wireless Controller 3.131.35.0.cpe2.3
 +dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
 +wlctl: xmlGetMxpktAttr(attrName maxpacket, attrValue 0)
 +ip is  192.168.1.1mask is  255.255.255.0, ipbegin is  192.168.1.33, ipend is  19
 +2.168.1.254
 +wlctl: xmlGetMxpktAttr(attrName maxpacket, attrValue 0)
 +bcmSetAtmConfigMode Current mode is:atmctl configmode ptmprotocol
 +adslctl: not found
 +adslctl: not found
 +ip_tables: (C) 2000-2002 Netfilter core team
 +ip_conntrack version 2.1 (255 buckets, 0 max) - 368 bytes per conntrack
 +ip_conntrack_pptp version 2.1 loaded
 +ip_nat_pptp version 2.0 loaded
 +ip_nat_irc: Unknown symbol needs_ip_conntrack_irc
 +insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_irc
 +.ko': Success (2): Success
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +HSTMGR INFO at bcm_transfer.c,42: BCM6505 reset and ADSL/VDSL mode selection.
 +=========pchr is:atmctl traffic atm
 +atmctl intf --settype 0 utopia level2
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +RELAY INFO at bcm_socket.c,199: Try socket connection for 90 seconds.
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +HSTMGR INFO at bcm_transfer.c,47: hpi_Init.
 +HSTMGR INFO at bcm_transfer.c,51: utopia_Init.
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +HSTMGR INFO at bcm_boot.c,95: Booting the BCM17f7 device 0.
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +HSTMGR INFO at bcm_transfer.c,168: Setting PLL speed.
 +HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[3] = 0x8a.
 +HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[2] = 0x3e.
 +HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[VDSLCTL FAILURE at bcm_soc
 +ket.c,177: could not connect.
 +1] = 0x21.
 +HSTMGR INFO at bcm_transfer.c,180: Written pll_Config[0] = 0x13.
 +HSTMGR INFO at bcm_transfer.c,186: Wait for PLL lock.
 +HSTMGR INFO at bcm_transfer.c,197: PLL locked OK.
 +HSTMGR INFO at bcm_transfer.c,204: Select PLL.
 +HSTMGR INFO at bcm_transfer.c,212: PLL Active (assumed).
 +HSTMGR INFO at bcm_transfer.c,132: 6510 Magic Register = 0x03.
 +Loading image .. done
 +HSTMGR INFO at bcm_boot.c,245: Boot firmware release: 4.0.0.
 +HSTMGR INFO at bcm_boot.c,248: HMI download protocol: 1.0.
 +Loading target image through HMI:  0%  0% VDSLCTL FAILURE at bcm_socket.c,177: could
 + not connect.
 + 0%  0%  0%  0%  0%  0%  1%  1%  1%  1%  1%  1%  1%  2%  2%  2%  2%  2%  2%  2%  3%  3%  3%  3%  3%  3%  3%  4%  4%  4%  4%  4%  4%  5%  5%  5%  5%  5%  5%  5%  6%  6%  6%  6%  6%  6%  6%  7%  7%  7%  7%  7%  7%  7%  8%  8%  8%  8%  8%  8%  8%  9%  9%  9%  9%  9%  9% 10% 10% 10% 10% 10% 10% 10% 11% 11% 11% 11% 11% 11% 11% 12% 12% 12% 12% 12% 12% 12% 13% 13% 13% 13% 13% 13% 14% 14% 14% 14% 14% 14% 14% 15% 15% 15% 15% 15% 15% 15% 16% 16% 16% 16% 16% 16% 16% 17% 17% 17% 17% 17% 17% 17% 18% 18% 18% 18% 18% 18% 19% 19% 19% 19% 19% 19% 19% 20% 20% 20% 20% 20% 20% 20% 21% 21% 21% 21% 21% 21% 21% 22% 22% 22% 22% 22% 22% 22% 23% 23% 23% 23% 23% 23% 24% 24% 24% 24% 24% 24% 24% 25% 25% 25% 25% 25% 25% 25% 26% 26% 26% 26% 26% 26% 26% 27% 27% 27% 27% 27% 27% 28% 28% 28% 28% 28% 28% 28% 29% 29% 29% 29% 29% 29% 29% 30% 30% 30% 30% 30% 30% 30% 31% 31% 31% 31% 31% 31% 31% 32% 32% 32% 32% 32% 32% 33% 33% 33% 33% 33% 33% 33% 34% 34% 34% 34% 34% 34% 34% 35% 35% 35% 35% 35% 35% 35% 36% 36% 36% 36% 36% 36% 36% 37% 37% 37% 37% 37% 37% 38% 38% 38% 38% 38% VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +38% 38% 39% 39% 39% 39% 39% 39% 39% 40% 40% 40% 40% 40% 40% 40% 41% 41% 41% 41% 41% 41% 42% 42% 42% 42% 42% 42% 42% 43% 43% 43% 43% 43% 43% 43% 44% 44% 44% 44% 44% 44% 44% 45% 45% 45% 45% 45% 45% 45% 46% 46% 46% 46% 46% 46% 47% 47% 47% 47% 47% 47% 47% 48% 48% 48% 48% 48% 48% 48% 49% 49% 49% 49% 49% 49% 49% 50% 50% 50% 50% 50% 50% 51% 51% 51% 51% 51% 51% 51% 52% 52% 52% 52% 52% 52% 52% 53% 53% 53% 53% 53% 53% 53% 54% 54% 54% 54% 54% 54% 54% 55% 55% 55% 55% 55% 55% 56% 56% 56% 56% 56% 56% 56% 57% 57% 57% 57% 57% 57% 57% 58% 58% 58% 58% 58% 58% 58% 59% 59% 59% 59% 59% 59% 59% 60% 60% 60% 60% 60% 60% 61% 61% 61% 61% 61% 61% 61% 62% 62% 62% 62% 62% 62% 62% 63% 63% 63% 63% 63% 63% 63% 64% 64% 64% 64% 64% 64% 65% 65% 65% 65% 65% 65% 65% 66% 66% 66% 66% 66% 66% 66% 67% 67% 67% 67% 67% 67% 67% 68% 68% 68% 68% 68% 68% 68% 69% 69% 69% 69% 69% 69% 70% 70% 70% 70% 70% 70% 70% 71% 71% 71% 71% 71% 71% 71% 72% 72% 72% 72% 72% 72% 72% 73% 73% 73% 73% 73% 73% 73% 74% 74% 74% 74% 74% 74% 75% 75% 75% 75% 75% 75% 75% 76% 76% 76% 76% 76% 76% 76% 77% 77% VDSLCTL FAILURE at bcm_socket.c,177: could not connect.
 +77% 77% 77% 77% 77% 78% 78% 78% 78% 78% 78% 79% 79% 79% 79% 79% 79% 79% 80% 80% 80% 80% 80% 80% 80% 81% 81% 81% 81% 81% 81% 81% 82% 82% 82% 82% 82% 82% 82% 83% 83% 83% 83% 83% 83% 84% 84% 84% 84% 84% 84% 84% 85% 85% 85% 85% 85% 85% 85% 86% 86% 86% 86% 86% 86% 86% 87% 87% 87% 87% 87% 87% 88% 88% 88% 88% 88% 88% 88% 89% 89% 89% 89% 89% 89% 89% 90% 90% 90% 90% 90% 90% 90% 91% 91% 91% 91% 91% 91% 91% 92% 92% 92% 92% 92% 92% 93% 93% 93% 93% 93% 93% 93% 94% 94% 94% 94% 94% 94% 94% 95% 95% 95% 95% 95% 95% 95% 96% 96% 96% 96% 96% 96% 96% 97% 97% 97% 97% 97% 97% 98% 98% 98% 98% 98% 98% 98% 99% 99% 99% 99% 99% 99% 99% done
 +HSTMGR INFO at bcm_hostMgr.c,94: Interrupt polling enabled.
 +bind now the file descriptor from IP 0.0.0.0, my port 57665.
 +vdslctl: Started successfully
 +RELAY INFO at bcm_socket.c,224: Connected successfully (fd: 6).
 +=========pchr is:atmctl traffic atm
 +
 +==>  Bcm963xx VDSL Software Version: 09.02.07, 2006-11-15  <==
 +
 +
 +==>  Bcm963xx Software Version: V100R001C02B066_V_SP3  <==
 +
 +atmctl intf --settype 0 utopia level2
 +========bcm63xx_enet_open dev->name is:eth0
 +device eth0 entered promiscuous mode
 +br0: port 1(eth0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 1(eth0) entering forwarding state
 +pvc2684ctl_main trafficmode:2
 +pvc2684d_main:2
 +setIndexName1
 +pvc2684d: Interface "nas_0_32_0" created sucessfully
 +
 +AttachVcc g_nPtmConfig:2
 +setIndexName1
 +pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC
 +
 +device nas_0_32_0 entered promiscuous mode
 +br0: port 2(nas_0_32_0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 2(nas_0_32_0) entering forwarding state
 +device eth0 left promiscuous mode
 +br0: port 1(eth0) entering disabled state
 +eth0.2: MAC Address: XX:XX:XX:XX:XX:XX
 +eth0.3: MAC Address: XX:XX:XX:XX:XX:XX
 +eth0.4: MAC Address: XX:XX:XX:XX:XX:XX
 +eth0.5: MAC Address: XX:XX:XX:XX:XX:XX
 +device eth0.2 entered promiscuous mode
 +br0: port 1(eth0.2) entering learning state
 +br0: topology change detected, propagating
 +br0: port 1(eth0.2) entering forwarding state
 +device eth0.3 entered promiscuous mode
 +br0: port 3(eth0.3) entering learning state
 +br0: topology change detected, propagating
 +br0: port 3(eth0.3) entering forwarding state
 +device eth0.4 entered promiscuous mode
 +br0: port 4(eth0.4) entering learning state
 +br0: topology change detected, propagating
 +br0: port 4(eth0.4) entering forwarding state
 +device eth0.5 entered promiscuous mode
 +br0: port 5(eth0.5) entering learning state
 +br0: topology change detected, propagating
 +br0: port 5(eth0.5) entering forwarding state
 +In webmain, setup wlan
 +br0: port 1(eth0.2) entering disabled state
 +br0: port 3(eth0.3) entering disabled state
 +br0: port 4(eth0.4) entering disabled state
 +br0: port 5(eth0.5) entering disabled state
 +
 +Login:
 +</code>
 +</p>
 +</HTML>
 +
 +==== OpenWrt ====
 +<HTML>
 +<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
 +<code>[    0.000000] Linux version 3.6.11 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #4 Wed Jan 9 20:07:04 CET 2013
 +[    0.000000] Detected Broadcom 0x6358 CPU revision a1
 +[    0.000000] CPU frequency is 300 MHz
 +[    0.000000] 32MB of RAM installed
 +[    0.000000] registering 40 GPIOs
 +[    0.000000] board_bcm963xx: Boot address 0xbfc00000
 +[    0.000000] board_bcm963xx: CFE version: 100.48.54-48.46
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx: board name: HW6358GW_B
 +[    0.000000] Determined physical RAM map:
 +[    0.000000]  memory: 02000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000]  Normal  [mem 0x00000000-0x01ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]  node  0: [mem 0x00000000-0x01ffffff]
 +[    0.000000] On node 0 totalpages: 8192
 +[    0.000000] free_area_init_node: node 0, pgdat 802a8db0, node_mem_map 81000000
 +[    0.000000]  Normal zone: 64 pages used for memmap
 +[    0.000000]  Normal zone: 0 pages reserved
 +[    0.000000]  Normal zone: 8128 pages, LIFO batch:0
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
 +[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
 +[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
 +[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.000000] __ex_table already sorted, skipping sort
 +[    0.000000] Memory: 28356k/32768k available (2260k kernel code, 4412k reserved, 400k data, 1072k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.032000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 512
 +[    0.048000] NET: Registered protocol family 16
 +[    0.060000] registering PCI controller with io_map_base unset
 +[    0.080000] bio: create slab <bio-0> at 0
 +[    0.088000] PCI host bridge to bus 0000:00
 +[    0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
 +[    0.096000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
 +[    0.100000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 +[    0.104000] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff]
 +[    0.104000] pci 0000:00:01.0: [14e4:4318] type 00 class 0x028000
 +[    0.104000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00001fff]
 +[    0.116000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
 +[    0.116000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff]
 +[    0.120000] Switching to clocksource MIPS
 +[    0.132000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
 +[    0.136000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
 +[    0.160000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x00
 +[    0.168000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
 +[    0.168000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
 +[    0.168000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
 +[    0.168000] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
 +[    0.208000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
 +[    0.216000] NET: Registered protocol family 2
 +[    0.224000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +[    0.232000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.236000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.244000] TCP: reno registered
 +[    0.248000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.252000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.260000] NET: Registered protocol family 1
 +[    0.264000] PCI: CLS 0 bytes, default 16
 +[    2.744000] audit: initializing netlink socket (disabled)
 +[    2.748000] type=2000 audit(2.748:1): initialized
 +[    2.756000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    2.760000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    2.772000] msgmni has been set to 55
 +[    2.776000] io scheduler noop registered
 +[    2.780000] io scheduler deadline registered (default)
 +[    2.788000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
 +[    2.796000] console [ttyS0] enabled, bootconsole disabled
 +[    2.812000] physmap platform flash device: 00400000 at 1fc00000
 +[    2.816000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a01
 +[    2.828000] Amd/Fujitsu Extended Query Table at 0x0040
 +[    2.832000]  Amd/Fujitsu Extended Query version 1.3.
 +[    2.840000] physmap-flash.0: Swapping erase regions for top-boot CFI table.
 +[    2.844000] number of CFI chips: 1
 +[    2.848000] bcm63xxpart: CFE boot tag found with version 6 and board type HW6358GW_B
 +[    2.856000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
 +[    2.864000] bcm63xxpart: Partition 1 is rootfs offset 10100 and length 2bb000
 +[    2.872000] bcm63xxpart: Partition 2 is kernel offset 2cb100 and length 8aac4
 +[    2.880000] bcm63xxpart: Partition 3 is nvram offset 3f0000 and length 10000
 +[    2.884000] bcm63xxpart: Partition 4 is linux offset 10000 and length 3e0000
 +[    2.892000] bcm63xxpart: Spare partition is offset 360000 and length 90000
 +[    2.900000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
 +[    2.908000] Creating 5 MTD partitions on "physmap-flash.0":
 +[    2.912000] 0x000000000000-0x000000010000 : "CFE"
 +[    2.920000] 0x000000010100-0x0000002cb100 : "rootfs"
 +[    2.928000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    2.944000] mtd: partition "rootfs" set to be root filesystem
 +[    2.948000] split_squashfs: no squashfs found in "physmap-flash.0"
 +[    2.956000] 0x0000002cb100-0x000000355bc4 : "kernel"
 +[    2.960000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    2.976000] 0x0000003f0000-0x000000400000 : "nvram"
 +[    2.988000] 0x000000010000-0x0000003f0000 : "linux"
 +[    3.004000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
 +[    3.012000] TCP: cubic registered
 +[    3.016000] NET: Registered protocol family 17
 +[    3.020000] 8021q: 802.1Q VLAN Support v1.8
 +[    3.044000] Freeing unused kernel memory: 1072k freed
 +[    4.132000] roboswitch: Probing device 'eth0'
 +[    4.136000] roboswitch: found a 5325! It's a 5350. at eth0
 +[    5.192000] There is already a switch registered on the device 'eth0'
 +[  10.164000] There is already a switch registered on the device 'eth0'
 +[  10.192000] Button Hotplug driver version 0.4.1
 +[  10.240000] PPP generic driver version 2.4.2
 +[  10.332000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[  10.536000] NET: Registered protocol family 24
 +[  10.568000] nf_conntrack version 0.5.0 (459 buckets, 1836 max)
 +[  10.924000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542) v0.1.2
 +[  15.640000] eth0: link forced UP - 100/full - flow control off/off
 +[  62.056000] eth0: link forced UP - 100/full - flow control off/off
 +[  62.068000] device eth0 entered promiscuous mode
 +[  62.076000] br-lan: port 1(eth0) entered forwarding state
 +[  62.080000] br-lan: port 1(eth0) entered forwarding state
 +[  64.084000] br-lan: port 1(eth0) entered forwarding state
 +</code>
 +</p>
 +</HTML>
 +
 +===== Tags =====
 +{{tag>bcm63xx bcm6358 bcm6359}}

Back to top

toh/huawei/hg520v.txt · Last modified: 2013/01/11 15:11 (external edit)