User Tools

Site Tools


toh:huawei:hg630

Huawei HG630

Huawei HG630-52

Huawei HG630b

Not supported.

Not much info about these routers, but they have some interesting features:

  • HG630 and HG630-52 have a BCM63168 SoC and an SPI flash chip, most BCM63168 based boards use NAND flash chips.
  • HG630-52 and HG630b are identical boards, but the HG630b uses a NAND flash chip whereas HG630-52 uses an SPI flash chip. HG630b has more components soldered, like the WAN port.
  • The board Id is the same used by the HG658c, therefore the firmwares might be interchangeable.

Installation

Flashing ANY Firmware

You must set your TCP/IP v4 protocol to:

  1. IP: 192.168.1.2
  2. Netmask: 255.255.255.0
  3. Gateway: 192.168.1.1
  4. DNS: (optional, can be blank).

Then:

  1. Power off the router.
  2. Press reset button.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Acces to http://192.168.1.1 and upload binary file.
  5. Wait until router reboots.

Hardware

Info

HG630, HG630-52 HG630b
Instruction set: MIPS
Vendor: Broadcom
Bootloader: CFE
Board ID: 963268_hg658b 963268_hg630b
System-On-Chip: Broadcom BCM63168
CPU/Speed BMIPS4350 v8.0 / 400 MHz
SPI flash: 16 MiB not soldered, pads exposed
NAND flash: not soldered, pads exposed 128 MiB
RAM 64 MiB / DDR2
Wireless BCM6362 802.11b/g/n (SoC)
Antenna 2x
Ethernet: Integrated BCM63168 w/ vlan support swconfig
USB Yes
Power adapter 12V DC 1A / HW-120100U6W
Serial: Yes
JTAG: ?

Photos

HG630

HG630-52

HG630b

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

FIXME

Photo of PCB with markings

Bootlogs

OEM HG630 Bootlog

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 SIZ1 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 1.0.38-112.70 for BCM963268 (32bit,SP,BE) Build Date: Thu Jan 24 11:03:24 CST 2013 (zhanghuaxiang@X3755-vhg) Copyright (C) 2000-2011 Broadcom Corporation. HS Serial flash device: name S25FL128, id 0x0118 size 16384KB Total Flash size: 16384K with 256 sectors Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-0) : 963268_hg658b Number of MAC Addresses (1-32) : 10 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-64) KBytes : 0 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Boot :e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f f=vmlinux i=bcm963xx_fs_kernel d=1 p=0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 autoRun boot from main Booting from kernel offset (0xb85a2100) ... Booting from image main (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x800146c0 Decompression OK! Entry at 0x800146c0 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x800146c0 Linux version 2.6.30 (zhanghuaxiang@X3755-vhg) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #31 SMP PREEMPT Fri Jan 25 18:22:19 CST 2013 HS Serial flash device: name S25FL128, id 0x0118 size 16384KB 63268hg622b prom init CPU revision is: 0002a080 (Broadcom4350) DSL SDRAM reserved: 0x132000 Determined physical RAM map: memory: 03ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003ece On node 0 totalpages: 16078 free_area_init_node: node 0, pgdat 804991f0, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11888 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 58460k/64312k available (3666k kernel code, 5832k reserved, 995k data, 168k init, 0k highmem) Calibrating delay loop... 398.33 BogoMIPS (lpj=199168) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Jan 24 2013 10:48:12 CPU revision is: 0002a080 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 1152 bytes bhal: bhalInit entry NET: Registered protocol family 16 Internal 1P2 VREG is forced to remain enabled registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: disabled pci 0000:01:00.0: PREFETCH window: disabled PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Jan 24 2013 10:53:32 initialized Broadcom GBPM v0.1 Jan 24 2013 10:53:33 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM JFFS2 version 2.2. © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 114 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 NET: Registered protocol family 24 IMQ driver loaded successfully. Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. bcm963xx_mtd driver v2.1 ==boot from main kernel== rootfs_addr=0xb8010100 kernel_addr=0xb85a2100 BOOT_OFFSET:0xf8400000 Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8010100] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core usbcore: registered new interface driver usbtest MoniterInit entry Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX adsl: adsl_init entry bcmxtmcfg: bcmxtmcfg_init entry bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Jan 25 2013 18:19:29 bcmPktDma_init: Broadcom Packet DMA Library initialized Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1004 buckets, 4016 max) xt_time: kernel timezone is -0000 nf_nat_pt: no ports specified ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 168k freed =file:drivers/usb/core/hub.c,line:3274,func:hub_events=eventCounts=1= init started: BusyBox vv1.9.1 (2013-01-24 10:59:58 CST) starting pid 258, tty '': '/etc/init.d/rcS' RCS DONE starting pid 260, tty '': '/bin/sh' BusyBox vv1.9.1 (2013-01-24 10:59:58 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/startbsp: line 18: cannot create /dev/mtdblock2: No such device or address mount: mounting /dev/mtdblock2 on /config failed: No such file or directory -/bin/sh: usbdiagd: not found Loading drivers and kernel modules... bcm_ingqos: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Ingress QoS Module Char Driver v0.1 Jan 24 2013 10:51:57 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=6710886B (6MB), num of buffers=3201, buf size=2096 Broadcom BPM Module Char Driver v0.1 Jan 24 2013 10:51:56 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Jan 25 2013 18:19:24 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Jan 25 2013 18:19:24 chipId 0x631680D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jan 24 2013 10:51:59 Registered <241> FAP Debug values at 0x00000010 0x00000010 Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Allocated FAP0 GSO Buffers (0xA2A3D124) : 1048576 bytes @ 0xA2B00000 Allocated FAP1 GSO Buffers (0xA2A5D124) : 1048576 bytes @ 0xA2400000 [NTC fapProto] fapReset : Reset FAP Protocol layer [FAP0] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7096>, free <72>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7096>, free <72>, total<8192> [FAP0] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP1] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP0] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP1] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP0] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP1] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP0] GSO Buffer set to 0xA2B00000 [FAP1] GSO Buffer set to 0xA2400000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. bcmPktDma_bind: FAP Driver binding successfull Broadcom BCM63168D0 Ethernet Network Device v0.1 Jan 25 2013 18:19:21 fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b08206f0 bytes remaining 7008 ETH Init: Ch:0 - 200 tx BDs at 0xb08206f0 fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a206f0 bytes remaining 7008 ETH Init: Ch:1 - 200 tx BDs at 0xb0a206f0 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821690 bytes remaining 2192 ETH Init: Ch:0 - 600 rx BDs at 0xb0821690 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21690 bytes remaining 2192 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21690 eth0.3: MAC Address: 08:7A:4C:33:00:00 eth0.5: MAC Address: 08:7A:4C:33:00:00 eth0.4: MAC Address: 08:7A:4C:33:00:00 eth0.2: MAC Address: 08:7A:4C:33:00:00 =file:drivers/usb/core/hub.c,line:3274,func:hub_events=eventCounts=2= --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=2080 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=256 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_vars.bin Failed to open srom image from '/etc/wlan/bcm6362_vars.bin'. wl:loading /etc/wlan/bcm6362_map.bin wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.2001.cpe.L.3 p8021ag: p8021ag_init entry IRQ 8/BCM WATCHDOG: IRQF_DISABLED is not guaranteed on shared IRQs BCM Hardware Watchdog Timer for BCM96361 USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems Start mic now ... magic number is 3e 00 74 20. Read from flash ok. @.back up config file ok ! load cfm ok. start log proc... ifconfig: SIOCSIFNETMASK: Cannot assign requested address <6>br0: starting userspace STP failed, starting kernel STP add group failed: Operation not supported set group 0 mac learning disable in br0 failed: Operation not supported BcmAdsl_Initialize=0x8022496C, g_pFnNotifyCallback=0x8048CCC4 lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA3FFFFF8, 0x0 0x0 *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xD9E68 => 0x110570 *** AdslCoreSharedMemInit: shareMemAvailable=137840 AdslCoreHwReset: pLocSbSta=82630000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3F9AC2C fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22960 bytes remaining 592 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22960 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a22fa0 bytes remaining 464 XTM Init: Ch:1 - 16 rx BDs at 0xb0a22fa0 Success ARL table flush done Success atp: cur kernel version:[2.6.30] device eth0.3 entered promiscuous mode device eth0.4 entered promiscuous mode device eth0.5 entered promiscuous mode device eth0.2 entered promiscuous mode ADDRCONF(NETDEV_UP): eth0.2: link is not ready ADDRCONF(NETDEV_UP): eth0.3: link is not ready ADDRCONF(NETDEV_UP): eth0.4: link is not ready ADDRCONF(NETDEV_UP): eth0.5: link is not ready device eth0 is not a slave of br0 arp uses obsolete (PF_INET,SOCK_PACKET) wl: Unsupported device wl0 entered promiscuous mode br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state ------------------------------- -----Welcome to ATP Cli------ ------------------------------- Login: admin The console is prohibited!


OEM HG630b bootlog

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 SIZ1 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 1.0.38-114.174 for BCM963268 (32bit,SP,BE) Build Date: Wed Apr 2 11:24:49 CST 2014 (sunhongyong@X3755-vhg) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name <not identified>, id 0x98d1 block 128KB size 131072KB Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-1) : 963268_hg630b Number of MAC Addresses (1-32) : 10 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-64) KBytes : 0 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Boot :e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f f=vmlinux i=bcm963xx_fs_kernel d=1 p=0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Boot from slave system! SIGN CHK ALWAYLYS. get bootflag = 2 check tag at block 6 crc ok Check Image Crc Success I have find vmlinux.lz at block 291 I have get vmlinux.lz size at block 304 Decompression OK! Entry at 0x800146c0 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x800146c0 Linux version 2.6.30 (sunhongyong@X3755-vhg) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #7 SMP PREEMPT Wed Apr 2 11:25:47 CST 2014 ======== nand_flash_init ======= NAND flash device id 98d1 is not supported. Init Flash Error iReturn = -1 63268hg622b prom init CPU revision is: 0002a080 (Broadcom4350) DSL SDRAM reserved: 0x132000 Determined physical RAM map: memory: 03ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003ece On node 0 totalpages: 16078 free_area_init_node: node 0, pgdat 804b2c70, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11888 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 58028k/64312k available (3735k kernel code, 6264k reserved, 1030k data, 168k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Apr 2 2014 11:00:39 CPU revision is: 0002a080 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 1152 bytes bhal: bhalInit entry NET: Registered protocol family 16 Internal 1P2 VREG is forced to remain enabled registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: disabled pci 0000:01:00.0: PREFETCH window: disabled PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Apr 2 2014 11:06:33 initialized Broadcom GBPM v0.1 Apr 2 2014 11:06:33 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 113 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 NET: Registered protocol family 24 IMQ driver loaded successfully. Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. Broadcom DSL NAND controller (128MB @00000000 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=1, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=83a5f190, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 brcmnandCET: Status -> Deferred brcmnand_scan 99 Boot from slave system! iBlkStart 123 =======iBlkStart:292======= Creating 3 MTD partitions on "brcmnand.0": 0x000002460000-0x000004760000 : "rootfs" 0x000000160000-0x000002460000 : "rootfsbak" 0x0000070a0000-0x000007dc0000 : "config" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core usbcore: registered new interface driver usbtest MoniterInit entry Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX adsl: adsl_init entry bcmxtmcfg: bcmxtmcfg_init entry bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Apr 2 2014 11:05:36 bcmPktDma_init: Broadcom Packet DMA Library initialized Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1004 buckets, 4016 max) xt_time: kernel timezone is -0000 nf_nat_pt: no ports specified ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 168k freed =file:drivers/usb/core/hub.c,line:3274,func:hub_events=eventCounts=1= init started: BusyBox vv1.9.1 (2014-04-02 11:18:48 CST) starting pid 265, tty '': '/etc/init.d/rcS' RCS DONE starting pid 267, tty '': '/bin/sh' BusyBox vv1.9.1 (2014-04-02 11:18:48 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. -/bin/sh: usbdiagd: not found Loading drivers and kernel modules... bcm_ingqos: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Ingress QoS Module Char Driver v0.1 Apr 2 2014 11:04:45 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=6710886B (6MB), num of buffers=3201, buf size=2096 Broadcom BPM Module Char Driver v0.1 Apr 2 2014 11:04:44 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Apr 2 2014 11:04:43 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Apr 2 2014 11:04:43 chipId 0x631680D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Apr 2 2014 11:04:47 Registered <241> FAP Debug values at 0x00000010 0x00000010 Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Allocated FAP0 GSO Buffers (0xA2F1D124) : 1048576 bytes @ 0xA2800000 Allocated FAP1 GSO Buffers (0xA2F9D124) : 1048576 bytes @ 0xA2900000 [NTC fapProto] fapReset : Reset FAP Protocol layer [FAP0] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7096>, free <72>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1024>, global <0x80000400><7096>, free <72>, total<8192> [FAP0] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP1] PSM : addr<0x80002000>, used <24560>, free <16>, total <24576> [FAP0] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP1] Flows supported: 237 (dsp 60, psm 75, qsm 102) [FAP0] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP1] DQM : availableMemory 14188 bytes, nextByteAddress 0xE0010894 [FAP0] GSO Buffer set to 0xA2800000 [FAP1] GSO Buffer set to 0xA2900000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. bcmPktDma_bind: FAP Driver binding successfull Broadcom BCM63168D0 Ethernet Network Device v0.1 Apr 2 2014 11:04:36 fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b08206f0 bytes remaining 7008 ETH Init: Ch:0 - 200 tx BDs at 0xb08206f0 fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a206f0 bytes remaining 7008 ETH Init: Ch:1 - 200 tx BDs at 0xb0a206f0 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821690 bytes remaining 2192 ETH Init: Ch:0 - 600 rx BDs at 0xb0821690 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21690 bytes remaining 2192 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21690 eth0.3: MAC Address: FF:FF:FF:FF:FF:FF {Changed to protect the innocent} eth0.5: MAC Address: FF:FF:FF:FF:FF:FF {Changed to protect the innocent} eth0.4: MAC Address: FF:FF:FF:FF:FF:FF {Changed to protect the innocent} eth0.2: MAC Address: FF:FF:FF:FF:FF:FF {Changed to protect the innocent} nas0: MAC Address: FF:FF:FF:FF:FF:FF {Changed to protect the innocent} =file:drivers/usb/core/hub.c,line:3274,func:hub_events=eventCounts=2= --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=2080 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=512 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_vars.bin Failed to open srom image from '/etc/wlan/bcm6362_vars.bin'. wl:loading /etc/wlan/bcm6362_map.bin wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.2001.cpe.L.3 p8021ag: p8021ag_init entry IRQ 8/BCM WATCHDOG: IRQF_DISABLED is not guaranteed on shared IRQs BCM Hardware Watchdog Timer for BCM96361 USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems Start mic now ... magic number is 3e 00 65 b0. Read from flash ok. *****Start cfmUpgradeUpdateCfg()!***** *****No need update config[2]***** load cfm ok. start log proc... ifconfig: SIOCSIFNETMASK: Cannot assign requested address br0: starting userspace STP failed, starting kernel STP add group failed: Operation not supported set group 0 mac learning disable in br0 failed: Operation not supported BcmAdsl_Initialize=0x80232A70, g_pFnNotifyCallback=0x804A6694 lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA3FFFFF8, 0x6FECFDAF 0x65BBFE4D *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xD9E68 => 0x110570 *** AdslCoreSharedMemInit: shareMemAvailable=137840 AdslCoreHwReset: pLocSbSta=82b88000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3F9AC2C fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22960 bytes remaining 592 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22960 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a22fa0 bytes remaining 464 XTM Init: Ch:1 - 16 rx BDs at 0xb0a22fa0 Success ARL table flush done Success Read Prsite on! atp: cur kernel version:[2.6.30] device eth0.2 entered promiscuous mode device eth0.3 entered promiscuous mode device eth0.4 entered promiscuous mode device eth0.5 entered promiscuous mode ADDRCONF(NETDEV_UP): eth0.2: link is not ready ADDRCONF(NETDEV_UP): eth0.3: link is not ready ADDRCONF(NETDEV_UP): eth0.4: link is not ready ADDRCONF(NETDEV_UP): eth0.5: link is not ready device eth0 is not a slave of br0 arp uses obsolete (PF_INET,SOCK_PACKET) bcmPktDma_init: Broadcom Packet DMA Library initialized ------------------------------- -----Welcome to ATP Cli------ ------------------------------- Login:


Tags

toh/huawei/hg630.txt · Last modified: 2016/02/08 02:24 by tmomas