Differences

This shows you the differences between two versions of the page.

toh:huawei:hg655d [2013/07/05 13:14]
toh:huawei:hg655d [2014/07/17 17:43] (current)
ned14 Confirmed the HG655m has serial
Line 1: Line 1:
-====== Huawei HG655d ====== +====== Huawei HG655b/d/m ====== 
-The HG655d is an adsl/vdsl wifi router distributed by Online/T-Mobile Netherlands to their customers.+The HG655d is an adsl/vdsl wifi router distributed by Online/T-Mobile Netherlands to their customers. It has 64Mb of RAM, 8Mb of Flash, 2.4Ghz 11n Wifi and a USB port. 
 + 
 +The HG655m is a reduced cost adsl/vdsl router common in Asia. There is a particularly cheap edition (US$40) available on eBay at the moment which is a Telekom Malaysia unit for their Unifi fibre broadband service. Aliexpress has the same model going for US$30. It has 32Mb of RAM, 32Mb of Flash, no Wifi and no USB port. 
 + 
 +===== Supported Versions ===== 
 + 
 +^ Router version ^ Board model ^ Supported ^ Notes ^ 
 +| HG556b | HG655**<color crimson>B</color>**RZ VER.A  |  WIP  | <color crimson>ADSL not supported</color> | 
 +| HG556d | HG655**<color crimson>D</color>**RZ VER.A  |  WIP  |  ::: | 
 +| HG655m | AV1HG655MM VER.B                            | not supported | not supported | 
 + 
 +Forum: [[https://forum.openwrt.org/viewtopic.php?id=50207]]
===== Hardware Highlights ===== ===== Hardware Highlights =====
-^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ +^ Model ^ SoC ^ Ram ^ Flash ^ Network ^ VoIP POTS ^ USB ^ Serial ^ JTag ^ 
-| Broadcom 6368 | 64MiB | 8MiB | 4 x 1| Yes | Yes | Yes |+| HG655b/d | Broadcom 6368 | 64MiB | 8MiB | 4 x 1| 2 | Yes | Yes     | Yes     | 
 +| HG655m  | Broadcom 6368 | 32MiB | 32MiB | 4 x 1| 2 | No  | Yes | unknown | 
 + 
 + 
 +===== Installation ===== 
 +  - → [[doc:howto:obtain.firmware]] 
 +  - → [[doc:howto:generic.flashing|Install OpenWrt]] 
 +  - → [[about/latest|Latest OpenWrt release]] 
 + 
 +==== Flash Layout ==== 
 +Please check out the article [[doc:techref:Flash Layout]]. It contains an example and a couple of explanations. 
 + 
 +For the HG655b version, with the vendor firmware, the flash chip is divided in several areas storing data for different purposes: 
 +^Phys.Addr ^Lenght ^Description ^ 
 +| 0x00000000 | 131072 | CFE | 
 +| 0x00020000 | 256 | BCM image tag | 
 +| 0x00020100 | 5062656 | rootfs partition | 
 +| 0x00439100 | 909932 | kernel partition | 
 +| 0x00790000 | 65536 | XML config  | 
 +| 0x007a0000 | 65536 | ATP_LOG | 
 +| 0x007b0000 | 65536 | Div tr069 conf? Env …. | 
 +| 0x007c0000 | 65536 | [[#wifi.calibration.data|wifi calibration data]] | 
 +| 0x007e0000 | 65536 | passwords? | 
 + 
 +==== OEM easy installation ==== 
 +This section deals with how you install OpenWrt from a device freshly opened.   
 +  *Unplug the power cord 
 +  *Press the button labeled as //RESET//, don't release it yet! 
 +  *Plug the power cord 
 +  *Wait 10 seconds 
 +  *Release the //RESET// button 
 +  *Browse to http://192.168.1.1 
 +  *Select the .bin firmware file 
 +  *Upgrade software 
 +  *Wait for it to reboot 
 +  *Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed. 
 + 
 +==== OEM installation using the TFTP method ==== 
 + 
 +->  [[doc:howto:generic.flashing.tftp]] 
 + 
 +FIXME 
 + 
 +==== Upgrading OpenWrt ==== 
 +->  [[doc:howto:generic.sysupgrade]] 
 + 
 +If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. 
 + 
 +=== LuCI Web Upgrade Process === 
 + 
 +  * Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL 
 +  * Upload image file for sysupgrade to LuCI 
 +  * Wait for reboot 
 + 
 +=== Terminal Upgrade Process === 
 + 
 +  * Login as root via SSH on 192.168.1.1 
 +  * Use the following commands to upgrade. 
 + 
 +<code> 
 +cd /tmp/ 
 +wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc 
 +sysupgrade /tmp/xxx.abc 
 +</code> 
 + 
 +  *If sysupgrade does not support this router, use the following commands. 
 + 
 +<code> 
 +cd /tmp/ 
 +wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc 
 +mtd write /tmp/xxx.abc linux && reboot</code> 
 + 
 + 
 +===== Basic configuration ===== 
 +-> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\ 
 +Set up your Internet connection, configure wireless, configure USB port, etc. 
 + 
 + 
 +===== Specific Configuration ===== 
 +==== Interfaces ==== 
 + 
 +The default network configuration is: 
 +^ Interface Name ^ Description ^ Default configuration ^ 
 +| br-lan | LAN & WiFi | 192.168.1.1/24 |  
 +| vlan0 (eth0.1) | LAN ports (1 to 4) | Bridged |  
 +| wlan0 | WiFi | Bridged, Disabled |  
 + 
 +==== Switch Ports (for VLANs) ==== 
 +Numbers 0-3 are Ports 1-4 as labeled on the unit, 8 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 0 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. 
 +^ Port label ^ Switch port ^ 
 +| LAN 1 | 0 |  
 +| LAN 2 | 1 |  
 +| LAN 3 | 2 |  
 +| LAN 4 | 3 |  
 +| n/a | 8t |  
 + 
 +==== Failsafe mode ==== 
 +-> [[doc:howto:generic.failsafe]] 
 + 
 +==== Buttons ==== 
 +-> [[doc:howto:hardware.button]] on howto use and configure the hardware button(s). 
 + 
 +^ BUTTON ^ Event ^ GPIO ^ 
 +| RESET | reset | 34 | 
 +| WPS |  | 12 | 
 +| WLAN |  | ?? | 
 + 
 +==== Leds ==== 
 +->[[doc:uci:system#leds|System configuration: Leds]] 
 +^ Label ^ GPIO ^ 
 +| POWER | 22 | 
 +| DSL | 2 | 
 +| INTERNET | 5 | 
 +| LAN1 | 6 | 
 +| LAN2 | 7 | 
 +| LAN3 | 8 | 
 +| LAN4 | 9 | 
 +| WLAN | n/a | 
 +| WPS | 27 | 
 +| VOIP | 25 | 
 +| USB | 14 | 
 + 
 +===== Hardware ===== 
 +==== Info ==== 
 +^                                          ^ HG655b/d ^^ HG655m ^^ 
 +| **[[wp>Instruction set]]:**              | [[wp>MIPS architecture|MIPS]] |||| 
 +| **Vendor:**                              | [[wp>Broadcom]] |||| 
 +| **[[doc:techref:Bootloader]]:**          | [[doc:techref:bootloader:CFE]] |||| 
 +| **Board Id:** | HW65x |||| 
 +| **[[doc:hardware:soc|System-On-Chip]]:**  | BCM6368 |||| 
 +| **[[doc:hardware:cpu|CPU]] @Frq**        | BMIPS4350 V3.1 @400 MHz [[doc:hardware:soc:soc.broadcom.bcm63xx:smp|BMIPS Dual Core]] |||| 
 +| **Flash size:**                | 8192 KiB || 32768 KiB || 
 +| **Flash Chip:**                | S29GL064N90TF104 | 8KB block size x 8 bottom boot blocks | M29EWH | 128KB block size x 64 blocks | 
 +| ::: | ::: | 64KB block size x 127 main blocks | ::: | ::: | 
 +| **RAM size:**                  | 64 MiB  || 32 MiB || 
 +| **RAM Chips:**                  | ESMT M13S2561616A-5T / DDR-400  || Nanya NT5DS8M16HS-5T / DDR-400 || 
 +| **Wireless:**              | Ralink RT3062F 2.4GHz 802.11b/g/n  || None || 
 +| **[[doc:hardware:Switch]]:**    | integragted BCM6368 (Fast-ethernet, VLAN)  |||| 
 +| **[[doc/hardware/internet.access.technologies|Modem]]:**  | xDSL  |||| 
 +| **USB:**                        | Yes 1 x 2.0  || None || 
 +| **[[doc:hardware:port.serial|Serial]]:**  | [[#Serial|Yes]] || [[#Serial|Yes]] || 
 +| **[[doc:hardware:port.jtag|JTAG]]:**      | [[#JTAG|Yes]]  || unsure || 
 + 
 +==== Photos ==== 
 +Model Number 
 + 
 +//Front:// 
 + 
 +**Photo of front of the casing** 
 + 
 +//Back:// 
 + 
 +**Photo of back of the casing** 
 + 
 +==== Opening the case ==== 
 +**Note:** This will void your warranty! 
 + 
 +  *To remove the cover do a/b/c 
 + 
 +===== HG655b ===== 
 +{{:media:toh:huawei:hg655b-board1.jpg?400x300|}} 
 +{{:media:toh:huawei:hg655b-board2.jpg?400x300|}} 
 + 
 +===== HG655m ===== 
 +{{:media:toh:huawei:hg655m_front.jpg?400x400|}} 
 +{{:media:toh:huawei:hg655m_back.jpg?400x400|}} 
 +{{:media:toh:huawei:hg655m_leds.jpg?200x400|}} 
 + 
 +==== Serial ==== 
 +-> [[doc:hardware:port.serial]] general information about the serial port, serial port cable, etc. 
 + 
 +How to connect to the Serial Port of this specific device: 
 +^ J4  ^ 
 +| TX  | 
 +| GND | 
 +| VCC | 
 +| nc  | 
 +| RX  | 
 +Serial works at 3.3V 115200N1, see pin assignments above 
 +|<code>Speed (baud)    - 115200 
 +Data bits        - 8 
 +Stop bits        - 1 
 +Parity          - None 
 +Flow control    - None</code>|
-==== pin headers ==== 
-^ J4  ^  J5 ^ 
-| TX  | TDI  | 
-| GND | TMS  | 
-| VCC | TDO  | 
-| nc  | TRST | 
-| RX  | TCK  | 
==== JTAG ==== ==== JTAG ====
 +-> [[doc:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +How to connect to the JTAG Port of this specific device:
 +
 +**Photo of PCB with markings**
 +
 +^  J5 ^
 +| TDI  |
 +| TMS  |
 +| TDO  |
 +| TRST |
 +| TCK  |
 +
 +=== URJTAG ===
Using the urJtag with an FT2232H I was able to read the flash chip. Using the urJtag with an FT2232H I was able to read the flash chip.
Line 54: Line 255:
readmem 0x38000000 0x020000 hg655d-CFE.bin'' readmem 0x38000000 0x020000 hg655d-CFE.bin''
-==== Flash layout ====+=== ZJTAG ===
-The flash chip has two regions:+and using zjtag(i used version 1.5)
-''Region 0:   8 x  8 KB +''zjtag -probeonly /window:18000000 /nompi - to detect flash chip 
-Region 1: 127 x 64 KB''+zjtag -backup:custom /window:18000000 /start:18000000 /length:800000 /nompi - to backup all flash''
-^Phys.Addr ^Lenght ^Description ^ 
-| 0x38000000 | 66616 | CFE | 
-| 0x38020000 | 256 | BCM image tag | 
-| 0x38020100 | 4296704 | rootfs partition | 
-| 0x38439000 | 65536 | upnp config XML | 
-| 0x3843A000 | 65536 | ATP_LOG | 
-| 0x3843B000 |  | Div tr96 conf? Env …. | 
-| 0x38440000 |  |  | 
-==== BCM tag ====+===== Debricking ===== 
 +-> [[doc:howto:generic.debrick]]
-''FW_BCM.start = 0x0 +===== Bootloader Mods ===== 
-FW_BCM.vendor = Broadcom Corporatio +  - you could read about [[doc:techref:bootloader]] in general
-FW_BCM.version = ver. 2.0 +
-FW_BCM.chipid = 6368 +
-FW_BCM.model = HW65x +
-FW_BCM._unknown = +
-FW_BCM.image_size = 0x506e92 +
-FW_BCM.loader_addr = 0xbfc00000 +
-FW_BCM.loader_size = 0x10438 +
-FW_BCM.root_fs_addr = 0xbfc20100 +
-FW_BCM.root_fs_size = 0x419000 (4296704) +
-FW_BCM.kernel_addr = 0xc0039100 +
-FW_BCM.kernel_size = 0xdda5a (907866) +
-FW_BCM.base = 0xbfc0fbc8 +
-FW_BCM.rootfs offset 0x10538 +
-FW_BCM.kernel_load_addr = 0x80010000 +
-FW_BCM.kernel_start_addr = 0x80292000 +
-FW_BCM.payload_checksum = 0x0 +
-FW_BCM.data_crc = 0x72c3fcc5 +
-FW_BCM.header_crc = 0xe600ab66''+
-==== Serial ====+===== Hardware mods ===== 
 +  - as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience!
-Serial works at 3.3V 115200N1, see pin assignments above+==== 128MiB RAM Mod ====
-Login: admin+===== Bootlogs ===== 
 +==== OEM bootlog ==== 
 +<HTML> 
 +<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF"> 
 +<code>CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE) 
 +Build Date: Wed Mar 23 22:59:09 CST 2011 (lihua@IBM_x3500) 
 +Copyright (C) 2000-2008 Broadcom Corporation.
-Password: admin+Parallel flash device: name AM29LV320MB, id 0x2200, size 8192KB 
 +CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz 
 +CPU running TP0 
 +Total memory: 67108864 bytes (64MB) 
 +Boot Address 0xb8000000
-You are now in the ATP command window. **shell** will get you a regular prompt 
 +Board IP address                  : 192.168.1.1:ffffff00 
 +Host IP address                  : 192.168.1.100 
 +Gateway IP address                : 
 +Run from flash/host (f/h)        : f 
 +Default host run file name        : vmlinux 
 +Default host flash file name      : bcm963xx_fs_kernel 
 +Boot delay (0-9 seconds)          : 1 
 +Boot image (0=latest, 1=previous) : 0 
 +Board Id (0-6)                    : HW65x 
 +Number of MAC Addresses (1-32)    : 11 
 +Base MAC Address                  : 02:10:18:01:00:01 
 +PSI Size (1-64) KBytes            : 64 
 +Main Thread Number [0|1]          : 0 
-''# cat /proc/modules                                                             +*** Press any key to stop auto run (2 seconds) *** 
-rt3062ap 954736 0 - Live 0xc00ee000 (P)                                          +Auto run second count down: 221
-option 7296 0 - Live 0xc0013000                                                 +Decompression OK! 
-endpointdd 1792704 0 - Live 0xc0209000 (P)                                       +Entry at 0x80294000 
-dspdd 1573728 1 endpointdd, Live 0x8108c700 (P)                                 +Closing network. 
-bcm_enet 88576 0 - Live 0xc0022000 (P)                                           +Disabling Switch ports. 
-adsldd 268992 0 - Live 0xc00ab000 (P)                                           +Flushing Receive Buffers... 
-bcmxtmcfg 43472 1 adsldd, Live 0xc0055000 (P)                                   +0 buffers found. 
-pktcmf 99088 2 bcm_enet,bcmxtmcfg, Live 0xc003b000 (P)                          +Closing DMA Channels. 
-pktflow 39168 1 pktcmf, Live 0xc0017000 (P) +Starting program at 0x80294000 
-''+Linux version 2.6.21.5 (dongpeiying@IBM_x3500) (gcc version 4.2.3) #567 Thu Sep 1 17:40:41 CST 2011
-''# cat /proc/cpuinfo                                                             +Pri Table Addr = 0040
-system type            : CHIP96368                                             +
-processor              : 0                                                     +
-cpu model              : BMIPS 4350 V3.1                                       +
-BogoMIPS                : 398.33                                                 +
-wait instruction        : yes                                                   +
-microsecond timers      : yes                                                   +
-tlb_entries            : 32                                                     +
-extra interrupt vector  : no                                                     +
-hardware watchpoint    : no                                                     +
-ASEs implemented        :                                                       +
-VCED exceptions        : not available                                         +
-VCEI exceptions        : not available                                         +
-                                                                                 +
-unaligned exceptions            : 265  ''                                        +
-==== Useful external links ====+ulBootFlag = 0002 
 + 
 +Flash 0 at 0xb8000000 
 + 
 +  Size : 8 MB 
 + 
 +  Regions : 2 
 + 
 +    0 : 0x00000000 - 0x00002000 *  8 
 + 
 +    1 : 0x00010000 - 0x00010000 * 127 
 + 
 +CPU revision is: 0002a031 
 + 
 +Determined physical RAM map: 
 + 
 + memory: 03f00000 @ 00000000 (usable) 
 + 
 +On node 0 totalpages: 16128 
 + 
 +  DMA zone: 32 pages used for memmap 
 + 
 +  DMA zone: 0 pages reserved 
 + 
 +  DMA zone: 4064 pages, LIFO batch:0 
 + 
 +  Normal zone: 94 pages used for memmap 
 + 
 +  Normal zone: 11938 pages, LIFO batch:1 
 + 
 +Built 1 zonelists.  Total pages: 16002 
 + 
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 
 + 
 +brcm mips: enabling icache and dcache... 
 + 
 +Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes. 
 + 
 +Primary data cache 32kB, 2-way, linesize 16 bytes. 
 + 
 +Synthesized TLB refill handler (21 instructions). 
 + 
 +Synthesized TLB load handler fastpath (33 instructions). 
 + 
 +Synthesized TLB store handler fastpath (33 instructions). 
 + 
 +Synthesized TLB modify handler fastpath (32 instructions). 
 + 
 +PID hash table entries: 256 (order: 8, 1024 bytes) 
 + 
 +Using 200.000 MHz high precision timer. 
 + 
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) 
 + 
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) 
 + 
 +Memory: 59484k/64512k available (2081k kernel code, 5012k reserved, 490k data, 104k init, 0k highmem) 
 + 
 +KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000> 
 + 
 +Calibrating delay loop... 398.33 BogoMIPS (lpj=199168) 
 + 
 +Mount-cache hash table entries: 512 
 + 
 +wait instruction: enabled 
 + 
 +bhal: bhalInit entry 
 + 
 +NET: Registered protocol family 16 
 + 
 +registering PCI controller with io_map_base unset 
 + 
 +SCSI subsystem initialized 
 + 
 +usbcore: registered new interface driver usbfs 
 + 
 +usbcore: registered new interface driver hub 
 + 
 +usbcore: registered new device driver usb 
 + 
 +NET: Registered protocol family 8 
 + 
 +NET: Registered protocol family 20 
 + 
 +Time: MIPS clocksource has been installed. 
 + 
 +NET: Registered protocol family 2 
 + 
 +IP route cache hash table entries: 128 (order: -3, 512 bytes) 
 + 
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes) 
 + 
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes) 
 + 
 +TCP: Hash tables configured (established 2048 bind 2048) 
 + 
 +TCP reno registered 
 + 
 +squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher 
 + 
 +squashfs: LZMA suppport for slax.org by jro 
 + 
 +fuse init (API version 7.8) 
 + 
 +io scheduler noop registered (default) 
 + 
 +PPP generic driver version 2.4.2 
 + 
 +NET: Registered protocol family 24 
 + 
 +IMQ starting with 3 devices... 
 + 
 +IMQ driver loaded successfully. 
 + 
 + Hooking IMQ before NAT on PREROUTING. 
 + 
 + Hooking IMQ after NAT on POSTROUTING. 
 + 
 + 
 +==boot from main kernel== 
 + 
 +Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8020100,5062656] 
 + 
 +PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) 
 + 
 +PCI: Setting latency timer of device 0000:00:0a.0 to 64 
 + 
 +ehci_hcd 0000:00:0a.0: EHCI Host Controller 
 + 
 +ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 
 + 
 +ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500 
 + 
 +ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004 
 + 
 +usb usb1: configuration #1 chosen from 1 choice 
 + 
 +hub 1-0:1.0: USB hub found 
 + 
 +hub 1-0:1.0: 2 ports detected 
 + 
 +ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver 
 + 
 +PCI: Enabling device 0000:00:09.0 (0000 -> 0002) 
 + 
 +PCI: Setting latency timer of device 0000:00:09.0 to 64 
 + 
 +ohci_hcd 0000:00:09.0: OHCI Host Controller 
 + 
 +ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 
 + 
 +ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600 
 + 
 +usb usb2: configuration #1 chosen from 1 choice 
 + 
 +hub 2-0:1.0: USB hub found 
 + 
 +hub 2-0:1.0: 2 ports detected 
 + 
 +usbcore: registered new interface driver usblp 
 + 
 +drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver 
 + 
 +Initializing USB Mass Storage driver... 
 + 
 +usbcore: registered new interface driver usb-storage 
 + 
 +USB Mass Storage support registered. 
 + 
 +MoniterInit entry 
 + 
 +Serial: BCM63XX driver $Revision: 3.00 $ 
 + 
 +ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX 
 + 
 +ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX 
 + 
 +bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Sep  1 2011 17:39:10 
 + 
 +GACT probability on 
 + 
 +Mirror/redirect action on 
 + 
 +u32 classifier 
 + 
 +    input device check on  
 + 
 +    Actions configured  
 + 
 +Netfilter messages via NETLINK v0.30. 
 + 
 +ip_tables: (C) 2000-2006 Netfilter Core Team 
 + 
 +TCP cubic registered 
 + 
 +Initializing XFRM netlink socket 
 + 
 +NET: Registered protocol family 1 
 + 
 +NET: Registered protocol family 17 
 + 
 +NET: Registered protocol family 15 
 + 
 +Ebtables v2.0 registered 
 + 
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> 
 + 
 +All bugs added by David S. Miller <davem@redhat.com> 
 + 
 +VFS: Mounted root (squashfs filesystem) readonly. 
 + 
 +Freeing unused kernel memory: 104k freed 
 + 
 + 
 +init started: BusyBox vv1.9.1 (2011-09-01 17:42:00 CST) 
 + 
 +starting pid 104, tty '': '/etc/init.d/rcS' 
 +RCS DONE 
 + 
 +starting pid 106, tty '': '/bin/sh' 
 + 
 + 
 +BusyBox vv1.9.1 (2011-09-01 17:42:00 CST) built-in shell (ash) 
 +Enter 'help' for a list of built-in commands. 
 + 
 +-/bin/sh: atserver: not found 
 +-/bin/sh: usbdiagd: not found 
 +Loading drivers and kernel modules...  
 +pktflow: module license 'Proprietary' taints kernel. 
 + 
 +Broadcom Packet Flow Cache  Char Driver v2.2 Aug  6 2010 11:03:27 Registered<242> 
 + 
 +NBUFF v1.0 Initialized 
 + 
 +Broadcom Packet Flow Cache learning via BLOG enabled. 
 + 
 +Created Proc FS /procfs/fcache 
 + 
 +Broadcom Packet Flow Cache registered with netdev chain 
 + 
 +Constructed Broadcom Packet Flow Cache v2.2 Aug  6 2010 11:03:26 
 + 
 +Broadcom Packet CMF (Experimental) Char Driver v0.1 Jul 23 2010 17:43:15 Registered<232> 
 + 
 +Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jul 23 2010 17:43:15 Loaded 
 + 
 +bcmxtmcfg: bcmxtmcfg_init entry 
 + 
 +adsl: adsl_init entry 
 + 
 +KLOB extended to 2 pools 
 + 
 +KLOB extended to 3 pools 
 + 
 +KLOB extended to 4 pools 
 + 
 +KLOB extended to 5 pools 
 + 
 +KLOB extended to 6 pools 
 + 
 +KLOB extended to 7 pools 
 + 
 +KLOB extended to 8 pools 
 + 
 +Broadcom Packet CMF (Experimental) SWC RESET. 
 + 
 +Broadcom Packet CMF (Experimental) SWC INITIALIZED. 
 + 
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 23 2010 17:43:16 Registered 
 + 
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 23 2010 17:43:16 Registered 
 + 
 +Broadcom Packet CMF (Experimental) ENABLED. 
 + 
 +eth0.5: MAC Address: C8:D1:5E:0D:AD:6C 
 + 
 +eth0.4: MAC Address: C8:D1:5E:0D:AD:6C 
 + 
 +eth0.3: MAC Address: C8:D1:5E:0D:AD:6C 
 + 
 +eth0.2: MAC Address: C8:D1:5E:0D:AD:6C 
 + 
 +DSP Driver: DSP init stub 
 + 
 +Endpoint: endpoint_init entry 
 + 
 +PROV(ts: 4 s 740ms):ALLOC item = 0000 location = 0x83C96A80 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 747ms):ALLOC item = 0001 location = 0x83C96A00 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 755ms):ALLOC item = 0002 location = 0x83C96980 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 762ms):ALLOC item = 0003 location = 0x83C96900 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 769ms):ALLOC item = 0004 location = 0x83C96880 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 776ms):ALLOC item = 0005 location = 0x83C96800 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 783ms):ALLOC item = 0006 location = 0x83C96780 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 790ms):ALLOC item = 0007 location = 0x83C96700 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 798ms):ALLOC item = 0008 location = 0x83C96680 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 805ms):ALLOC item = 0009 location = 0x83C96600 size = 40 line = 0 
 + 
 +PROV(ts: 4 s 812ms):ALLOC item = 0011 location = 0x83CE2600 size = 4 line = 0 
 + 
 +PROV(ts: 4 s 819ms):ALLOC item = 0200 location = 0x81317E80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 826ms):ALLOC item = 0201 location = 0x81317D80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 833ms):ALLOC item = 0202 location = 0x81317C80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 841ms):ALLOC item = 0203 location = 0x81317B80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 848ms):ALLOC item = 0204 location = 0x81317A80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 855ms):ALLOC item = 0205 location = 0x81317980 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 863ms):ALLOC item = 0206 location = 0x81317880 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 870ms):ALLOC item = 0207 location = 0x81317780 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 877ms):ALLOC item = 0208 location = 0x81317680 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 884ms):ALLOC item = 0209 location = 0x81317580 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 892ms):ALLOC item = 0210 location = 0x81317480 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 899ms):ALLOC item = 0211 location = 0x81317380 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 906ms):ALLOC item = 0212 location = 0x81317280 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 913ms):ALLOC item = 0213 location = 0x81317180 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 921ms):ALLOC item = 0218 location = 0x81317080 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 928ms):ALLOC item = 0219 location = 0x8376FE80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 935ms):ALLOC item = 0220 location = 0x8376FD80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 942ms):ALLOC item = 0221 location = 0x8376FC80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 950ms):ALLOC item = 0222 location = 0x8376FB80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 957ms):ALLOC item = 0223 location = 0x8376FA80 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 964ms):ALLOC item = 0224 location = 0x8376F980 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 971ms):ALLOC item = 0225 location = 0x8376F880 size = 248 line = 0 
 + 
 +PROV(ts: 4 s 979ms):ALLOC item = 0400 location = 0x83CE2580 size = 4 line = 0 
 + 
 +PROV(ts: 4 s 986ms):ALLOC item = 0401 location = 0x83CE2500 size = 4 line = 0 
 + 
 +PROV(ts: 4 s 993ms):ALLOC item = 0402 location = 0x83CE2480 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 0  ms):ALLOC item = 0403 location = 0x83CE2400 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 7  ms):ALLOC item = 0404 location = 0x83CE2380 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 14 ms):ALLOC item = 0405 location = 0x83CE2300 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 21 ms):ALLOC item = 0406 location = 0x83CE2280 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 28 ms):ALLOC item = 0407 location = 0x83CE2200 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 35 ms):ALLOC item = 0408 location = 0x83CE2180 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 42 ms):ALLOC item = 0409 location = 0x83CE2100 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 49 ms):ALLOC item = 0410 location = 0x83122F80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 56 ms):ALLOC item = 0411 location = 0x83122F00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 64 ms):ALLOC item = 0412 location = 0x83122E80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 71 ms):ALLOC item = 0413 location = 0x83122E00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 78 ms):ALLOC item = 0423 location = 0x83122D80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 85 ms):ALLOC item = 0424 location = 0x83122D00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 92 ms):ALLOC item = 0414 location = 0x83122C80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 99 ms):ALLOC item = 0416 location = 0x83122C00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 106ms):ALLOC item = 0417 location = 0x83122B80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 113ms):ALLOC item = 0418 location = 0x83122B00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 120ms):ALLOC item = 0600 location = 0x83122A80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 127ms):ALLOC item = 0608 location = 0x83122A00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 134ms):ALLOC item = 0609 location = 0x83122980 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 141ms):ALLOC item = 0610 location = 0x83122900 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 149ms):ALLOC item = 0611 location = 0x83122880 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 156ms):ALLOC item = 0612 location = 0x83122800 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 163ms):ALLOC item = 0613 location = 0x83122780 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 170ms):ALLOC item = 0617 location = 0x83122700 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 177ms):ALLOC item = 0618 location = 0x83122680 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 184ms):ALLOC item = 0619 location = 0x83122600 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 191ms):ALLOC item = 0620 location = 0x83122580 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 198ms):ALLOC item = 2000 location = 0x83122500 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 205ms):ALLOC item = 0805 location = 0x83122480 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 212ms):ALLOC item = 2200 location = 0x83122400 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 219ms):ALLOC item = 2201 location = 0x83122380 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 226ms):ALLOC item = 2202 location = 0x83122300 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 233ms):ALLOC item = 2203 location = 0x83122280 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 241ms):ALLOC item = 0616 location = 0x83122200 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 248ms):ALLOC item = 2204 location = 0x83122180 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 255ms):ALLOC item = 2600 location = 0x83122100 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 262ms):ALLOC item = 2601 location = 0x8376EF80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 269ms):ALLOC item = 2602 location = 0x8376EF00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 276ms):ALLOC item = 2603 location = 0x8376EE80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 283ms):ALLOC item = 2604 location = 0x8376EE00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 290ms):ALLOC item = 2605 location = 0x8376ED80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 297ms):ALLOC item = 2606 location = 0x8376ED00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 304ms):ALLOC item = 2800 location = 0x8376EC80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 311ms):ALLOC item = 2801 location = 0x8376EC00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 318ms):ALLOC item = 2802 location = 0x83CF0C00 size = 1024 line = 0 
 + 
 +PROV(ts: 5 s 326ms):ALLOC item = 2803 location = 0x8376EB80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 333ms):ALLOC item = 0428 location = 0x8376EB00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 340ms):ALLOC item = 0429 location = 0x8376EA80 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 347ms):ALLOC item = 0430 location = 0x8376EA00 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 354ms):ALLOC item = 0415 location = 0x8376E980 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 361ms):ALLOC item = 0427 location = 0x8376E900 size = 4 line = 0 
 + 
 +PROV(ts: 5 s 368ms):ALLOC item = 0000 location = 0x83C96580 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 375ms):ALLOC item = 0001 location = 0x83C96500 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 383ms):ALLOC item = 0002 location = 0x83C96480 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 390ms):ALLOC item = 0003 location = 0x83C96400 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 397ms):ALLOC item = 0004 location = 0x83C96380 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 404ms):ALLOC item = 0005 location = 0x83C96300 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 411ms):ALLOC item = 0006 location = 0x83C96280 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 418ms):ALLOC item = 0007 location = 0x83C96200 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 426ms):ALLOC item = 0008 location = 0x83C96180 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 433ms):ALLOC item = 0009 location = 0x83C96100 size = 40 line = 1 
 + 
 +PROV(ts: 5 s 440ms):ALLOC item = 0011 location = 0x8376E880 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 447ms):ALLOC item = 0200 location = 0x8376F780 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 454ms):ALLOC item = 0201 location = 0x8376F680 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 461ms):ALLOC item = 0202 location = 0x8376F580 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 469ms):ALLOC item = 0203 location = 0x8376F480 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 476ms):ALLOC item = 0204 location = 0x8376F380 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 483ms):ALLOC item = 0205 location = 0x8376F280 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 491ms):ALLOC item = 0206 location = 0x8376F180 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 498ms):ALLOC item = 0207 location = 0x8376F080 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 505ms):ALLOC item = 0208 location = 0x8376DE80 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 512ms):ALLOC item = 0209 location = 0x8376DD80 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 520ms):ALLOC item = 0210 location = 0x8376DC80 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 527ms):ALLOC item = 0211 location = 0x8376DB80 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 534ms):ALLOC item = 0212 location = 0x8376DA80 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 541ms):ALLOC item = 0213 location = 0x8376D980 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 549ms):ALLOC item = 0218 location = 0x8376D880 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 556ms):ALLOC item = 0219 location = 0x8376D780 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 563ms):ALLOC item = 0220 location = 0x8376D680 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 570ms):ALLOC item = 0221 location = 0x8376D580 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 578ms):ALLOC item = 0222 location = 0x8376D480 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 585ms):ALLOC item = 0223 location = 0x8376D380 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 592ms):ALLOC item = 0224 location = 0x8376D280 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 599ms):ALLOC item = 0225 location = 0x8376D180 size = 248 line = 1 
 + 
 +PROV(ts: 5 s 607ms):ALLOC item = 0400 location = 0x8376E800 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 614ms):ALLOC item = 0401 location = 0x8376E780 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 621ms):ALLOC item = 0402 location = 0x8376E700 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 628ms):ALLOC item = 0403 location = 0x8376E680 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 635ms):ALLOC item = 0404 location = 0x8376E600 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 642ms):ALLOC item = 0405 location = 0x8376E580 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 649ms):ALLOC item = 0406 location = 0x8376E500 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 656ms):ALLOC item = 0407 location = 0x8376E480 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 663ms):ALLOC item = 0408 location = 0x8376E400 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 670ms):ALLOC item = 0409 location = 0x8376E380 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 677ms):ALLOC item = 0410 location = 0x8376E300 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 685ms):ALLOC item = 0411 location = 0x8376E280 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 692ms):ALLOC item = 0412 location = 0x8376E200 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 699ms):ALLOC item = 0413 location = 0x8376E180 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 706ms):ALLOC item = 0423 location = 0x8376E100 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 713ms):ALLOC item = 0424 location = 0x8376CF80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 720ms):ALLOC item = 0414 location = 0x8376CF00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 727ms):ALLOC item = 0416 location = 0x8376CE80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 734ms):ALLOC item = 0417 location = 0x8376CE00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 741ms):ALLOC item = 0418 location = 0x8376CD80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 748ms):ALLOC item = 0600 location = 0x8376CD00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 755ms):ALLOC item = 0608 location = 0x8376CC80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 762ms):ALLOC item = 0609 location = 0x8376CC00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 769ms):ALLOC item = 0610 location = 0x8376CB80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 777ms):ALLOC item = 0611 location = 0x8376CB00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 784ms):ALLOC item = 0612 location = 0x8376CA80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 791ms):ALLOC item = 0613 location = 0x8376CA00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 798ms):ALLOC item = 0617 location = 0x8376C980 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 805ms):ALLOC item = 0618 location = 0x8376C900 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 812ms):ALLOC item = 0619 location = 0x8376C880 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 819ms):ALLOC item = 0620 location = 0x8376C800 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 826ms):ALLOC item = 2000 location = 0x8376C780 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 833ms):ALLOC item = 0805 location = 0x8376C700 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 840ms):ALLOC item = 2200 location = 0x8376C680 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 847ms):ALLOC item = 2201 location = 0x8376C600 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 854ms):ALLOC item = 2202 location = 0x8376C580 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 861ms):ALLOC item = 2203 location = 0x8376C500 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 869ms):ALLOC item = 0616 location = 0x8376C480 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 876ms):ALLOC item = 2204 location = 0x8376C400 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 883ms):ALLOC item = 2600 location = 0x8376C380 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 890ms):ALLOC item = 2601 location = 0x8376C300 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 897ms):ALLOC item = 2602 location = 0x8376C280 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 904ms):ALLOC item = 2603 location = 0x8376C200 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 911ms):ALLOC item = 2604 location = 0x8376C180 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 918ms):ALLOC item = 2605 location = 0x8376C100 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 925ms):ALLOC item = 2606 location = 0x8376BF80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 932ms):ALLOC item = 2800 location = 0x8376BF00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 939ms):ALLOC item = 2801 location = 0x8376BE80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 946ms):ALLOC item = 2802 location = 0x83CF0800 size = 1024 line = 1 
 + 
 +PROV(ts: 5 s 954ms):ALLOC item = 2803 location = 0x8376BE00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 961ms):ALLOC item = 0428 location = 0x8376BD80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 968ms):ALLOC item = 0429 location = 0x8376BD00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 975ms):ALLOC item = 0430 location = 0x8376BC80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 982ms):ALLOC item = 0415 location = 0x8376BC00 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 989ms):ALLOC item = 0427 location = 0x8376BB80 size = 4 line = 1 
 + 
 +PROV(ts: 5 s 996ms):Allocated memory = 14200  
 + 
 +Endpoint: endpoint_init COMPLETED 
 + 
 +Start mic now ... 
 +load cfm ok. 
 +start log proc... 
 +************************Write flash to db now ..., ulCfgFileType = 0 
 +ifconfig: SIOCSIFNETMASK: Cannot assign requested address 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +wlancmd: wlan driver adapter not found 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +wlancmd: wlan driver adapter not found 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +wlancmd: wlan driver adapter not found 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +wlancmd: wlan driver adapter not found 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +PCI: Enabling device 0000:00:01.0 (0000 -> 0002) 
 + 
 +PCI: Setting latency timer of device 0000:00:01.0 to 64 
 + 
 + 
 + 
 +=== pAd = c03b5000, size = 448000 === 
 + 
 + 
 +<-- RTMPAllocAdapterBlock, Status=0 
 + 
 +pAd->CSRBaseAddress =0xb1000000, csr_addr=0xb1000000! 
 + 
 +sh: cannot kill pid 320: No such process 
 +device wl0 is not a slave of br0 
 +interface wl0.1 does not exist! 
 +interface wl0.2 does not exist! 
 +interface wl0.3 does not exist! 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +ifconfig: SIOCGIFFLAGS: No such device 
 +ifconfig: SIOCGIFFLAGS: No such device 
 + 
 + 
 + begin WlanUpInterfaces... 
 +RX DESC a335f000  size = 2048 
 + 
 +<-- RTMPAllocTxRxRingMemory, Status=0 
 + 
 +===Ralink RF DATA check ok==== 
 + 
 +1. Phy Mode = 9 
 + 
 +2. Phy Mode = 9 
 + 
 +3. Phy Mode = 9 
 + 
 +RTMPSetPhyMode: channel is out of range, use first channel=0  
 + 
 +MCS Set = ff ff 00 00 00 
 + 
 +RTMPFilterCalibration - can't find a valid value, loopcnt=102 stop calibratingSYNC - BBP R4 to 20MHz.l 
 + 
 +Main bssid = 72:d1:5e:0d:ad:6c 
 + 
 +<==== rt28xx_init, Status=0 
 + 
 +0x1300 = 00064320 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WEP-AD6C], LEN=[25] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WPA-AD6C], LEN=[25] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[CountryRegion=1], LEN=[16] 
 + 
 + 
 + 
 + wlan_mode set@@@RTPRIV_IOCTL_SET CMD=[WirelessMode=9], LEN=[15] 
 + 
 + come in , argv[2] = bgnmixed 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtOpMode=0], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[BasicRate=15], LEN=[13] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[FixedTxMode=HT], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtGi=0], LEN=[7] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtBw=1], LEN=[7] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtMcs=33], LEN=[9] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtAutoBa=1], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtRdg=1], LEN=[8] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtStbc=1], LEN=[9] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[BGProtection=0], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[ShortSlot=1], LEN=[12] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[HtOpMode=0], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[BasicRate=15], LEN=[13] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[FixedTxMode=HT], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[RTSThreshold=2347], LEN=[18] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[FragThreshold=2346], LEN=[19] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[DtimPeriod=1], LEN=[13] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[BeaconPeriod=100], LEN=[17] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[NoForwarding=0], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[MaxStaNum=32], LEN=[13] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[IgmpSnEnable=1], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[NoForwarding=0], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[MaxStaNum=32], LEN=[13] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[IgmpSnEnable=1], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[WmmCapable=1], LEN=[13] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[TxBurst=0], LEN=[10] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[TxPower=95], LEN=[11] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15] 
 + 
 + 
 + 
 + begin WlanSetupBridge... 
 +device wl0 entered promiscuous mode 
 + 
 +br0: port 1(wl0) entering learning state 
 + 
 +br0: topology change detected, propagating 
 + 
 +br0: port 1(wl0) entering forwarding state 
 + 
 +device wl0.1 entered promiscuous mode 
 + 
 +br0: port 2(wl0.1) entering learning state 
 + 
 +br0: topology change detected, propagating 
 + 
 +br0: port 2(wl0.1) entering forwarding state 
 + 
 + 
 + 
 + begin WlanStartServices... 
 +@@@RTPRIV_IOCTL_SET CMD=[AuthMode=OPEN], LEN=[14] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[EncrypType=wep], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[IEEE8021X=0], LEN=[12] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[Key1=34574B415A5254513653564344], LEN=[32] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[DefaultKeyID=1], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[Key2=32323232323232323232323232], LEN=[32] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[Key3=33333333333333333333333333], LEN=[32] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[Key4=34343434343434343434343434], LEN=[32] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[AuthMode=WPA2PSK], LEN=[17] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[EncrypType=AES], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[IEEE8021X=0], LEN=[12] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[WPAPSK=SWYTLEJR6ALQ3], LEN=[21] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[DefaultKeyID=1], LEN=[15] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WEP-AD6C], LEN=[25] 
 + 
 +@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WPA-AD6C], LEN=[25] 
 + 
 +ATP_WLAN_Init SUCCESS!! 
 +bcmxtmrt: MAC address: c8 d1 5e 0d ad 6d 
 + 
 +Use default bin /var/cwmp now ... 
 + 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully...bcmxtmrt: MAC address: c8 d1 5e 0d ad 6e 
 + 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully...bcmxtmrt: MAC address: c8 d1 5e 0d ad 6f 
 + 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully...BcmAdsl_Initialize=0xC00AE834, g_pFnNotifyCallback=0xC00D67C4 
 + 
 +Clocks for QPROC and AFE are being aligned with step through ...  
 + 
 +AFE is aligned, i = 052, PhaseValue = -050, PhaseCntl = 0x3FCC0000 
 + 
 +QPROC is aligned, i = 053, PhaseValue = -050, PhaseCntl = 0x3FCC3FCB 
 + 
 +Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70 
 + 
 +AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f 
 + 
 +QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f 
 + 
 +pSdramPHY=0xA3FFFFF8, 0xDBA5BEA5 0x73EDFE25 
 + 
 +*** XfaceOffset: 0x5FF90 => 0x5FF90 *** 
 + 
 +*** PhySdramSize got adjusted: 0xBE300 => 0xEBA20 *** 
 + 
 +AdslCoreSharedMemInit: shareMemAvailable=83392 
 + 
 +AdslCoreHwReset:  AdslOemDataAddr = 0xA3FB3C78 
 + 
 +insmod: can't open '/lib/extra/vnet.ko': No such file or directory 
 +device eth0.5 entered promiscuous mode 
 + 
 +device eth0.2 entered promiscuous mode 
 + 
 +device eth0.3 entered promiscuous mode 
 + 
 +device eth0.4 entered promiscuous mode 
 + 
 +device eth0 is not a slave of br0 
 +ifconfig: SIOCGIFFLAGS: No such device 
 + 
 + ERROR: set wan media error.  
 +atp: cur kernel version:[2.6.21.5]  
 + 
 +bridge: can't decode speed from nas_a2_1: 0 
 + 
 +device nas_a2_1 entered promiscuous mode 
 + 
 +br0: port 7(nas_a2_1) entering learning state 
 + 
 +br0: topology change detected, propagating 
 + 
 +br0: port 7(nas_a2_1) entering forwarding state 
 + 
 +br0: port 7(nas_a2_1) entering disabled state 
 + 
 +/var/wan/nas_a3_2/dial: line 1: 3: not found 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:wl0.2 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:wl0.2 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:wl0.3 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +port_no -1 not surported, br:br0, port:wl0.3 
 +port_no -1 not surported, br:br0, port:nas_a1_0 
 +Ritchie app, 0 
 +Cannot find device "nas0" 
 +Cannot find device "nas0" 
 +Action 4 device imq0 ifindex 2 
 +Cannot find device "nas0" 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +iptables: Bad rule (does a matching rule exist in that chain?) 
 +FILE:voicecfg.c,LINE:89,sizeof(TAPI)=884,sizeof(SVC)=31856,sizeof(STATE)=14152 
 + 
 + 
 +Current sntp process is 1119! 
 + 
 + 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction in disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 + 
 +Set Mirror direction out disabled to eth0.2 Successfully... 
 +Sean@All modules init return 0. 
 +DEBUG[tapi.c:L1252]TAPI_GetCfg 
 +BOS: Enter bosIniBOS: Enter bosInit  
 + 
 +t  
 +bosTimerInitEnter bosAppInit  
 + 
 + 
 +Enter bosAppInExit bosAppInit  
 + 
 +it  
 +Exit bosAppBOS: Exit bosInit  
 + 
 +Init  
 +BOS: Exitendpoint_open COMPLETED 
 + 
 + bosInit  
 +Created message queue "HDSP", depth 40, id 1 
 +00:00:21 CAEnter bosStartApp 
 + 
 +LLCLIENT: Initia 
 + 
 + 
 +bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)... 
 + 
 + 
 +lizing endpointsAppResetDetectionEnable() - Enabled reset detection. 
 + 
 + callSipClientMaExit bosStartApp 
 + 
 +in 
 +Error getting IP address 
 +sipConfig: sipzParamp=0x7f3ffa44 sipzParamp->regname=129.102.100.11 line 62 file  hsip.c 
 +sipConfig: sipzParamp=0x7f3ffa44line 72 file  hsip.c 
 +sipConfig: &mgscb=0x51cf74line 85 file  hsip.c 
 +00:00:21 CALLCLIENT: Initializing endpoints 
 +00:00:21 Endpoint will be initialized for country ETS (country code = 7) 
 + 
 +Endpoint Event task started with pid 1141... 
 +Endpoint Packet task started with pid 1142 ... 
 +br0: port 4(eth0.2) entering disabled state 
 + 
 +br0: port 5(eth0.3) entering disabled state 
 + 
 +br0: port 6(eth0.4) entering disabled state 
 + 
 +br0: port 3(eth0.5) entering disabled state 
 + 
 +ifconfig: SIOCSIFFLAGS: Cannot assign requested address 
 +bridge br0:9 doesn't exist; can't delete it 
 +Append upnp ssdp listener ok. 
 +Use default bin /var/upnp now ... 
 +Enable Got value: 1 
 +NATEnabled Got value: 1 
 + 
 +BHAL(ts: 22s 557ms):Initializing board HAL... 
 + 
 +Codec Support: PCMA/PCMU 
 + 
 +Codec Support: G722 
 + 
 +Codec Support: G729A 
 + 
 +Codec Support: G729B 
 + 
 +Codec Support: G723 
 + 
 +Codec Support: G726 
 + 
 +Codec Support: BV16 
 + 
 +Codec Support: BV32 
 + 
 +Codec Support: LINPCM128 
 + 
 +Codec Support: LINPCM256 
 + 
 +Codec Support: ILBC 
 + 
 +Codec Support: AMRNB 
 + 
 +Codec Support: AMRWB 
 + 
 +Codec Support: T.38 
 + 
 +PCM: Interrupt Masks 
 + 
 +--------------- 
 + 
 +IrqMask                    = 0x000007070000A0B4  
 + 
 +IrqMask1                  = 0x0000000000000000  
 + 
 +PCM_IUDMA->ctrl[0].intMask = 0x00000000  
 + 
 +PCM_IUDMA->ctrl[1].intMask = 0x00000000  
 + 
 + 
 +PCM: Interrupt Status 
 + 
 +----------------- 
 + 
 +IrqStatus                  = 0x0000000000000040  
 + 
 +IrqStatus1                = 0x0000000000000040  
 + 
 +PCM_IUDMA->ctrl[0].intStat = 0x00000000  
 + 
 +PCM_IUDMA->ctrl[1].intStat = 0x00000000  
 + 
 +PCM->pcm_pll_ctrl1        = 0xFC80287D  
 + 
 +PCM->pcm_pll_ctrl2        = 0xD0000000  
 + 
 +PCM->pcm_pll_ctrl3        = 0x380005C0  
 + 
 +PCM->pcm_pll_ctrl4        = 0x00000000  
 + 
 +PCM->pcm_int_pending      = 0x00000000  
 + 
 +PCM->pcm_int_mask          = 0x00000000  
 + 
 +PCM->pcm_ctrl              = 0x00000000  
 + 
 +PCM->pcm_chan_ctrl        = 0x00000000  
 + 
 +PCM_IUDMA->regs.ctrlConfig = 0x00000001  
 + 
 +PCM_IUDMA->ctrl[0].maxBurst                  = 0x00000008  
 + 
 +PCM_IUDMA->ctrl[0].config                    = 0x00000000  
 + 
 +PCM_IUDMA->stram[0].baseDescPointer          = 0x0220CCC2  
 + 
 +PCM_IUDMA->stram[0].stateBytesDoneRingOffset = 0xB3601008  
 + 
 +PCM_IUDMA->stram[0].flagsLengthStatus        = 0x400A5B08  
 + 
 +PCM_IUDMA->stram[0].currentBufferPointer    = 0xD68A0052  
 + 
 +PCM_IUDMA->ctrl[1].maxBurst                  = 0x00000008  
 + 
 +PCM_IUDMA->ctrl[1].config                    = 0x00000000  
 + 
 +PCM_IUDMA->stram[1].baseDescPointer          = 0x802A1582  
 + 
 +PCM_IUDMA->stram[1].stateBytesDoneRingOffset = 0x08128848  
 + 
 +PCM_IUDMA->stram[1].flagsLengthStatus        = 0x2BD74905  
 + 
 +PCM_IUDMA->stram[1].currentBufferPointer    = 0x2258A8EE  
 + 
 +PLL init completed. PLL registers set to: 
 + 
 +PCM->pcm_pll_ctrl1      = 0x0080147D  
 + 
 +PCM->pcm_pll_ctrl2      = 0x10000000  
 + 
 +PCM->pcm_pll_ctrl3      = 0x38000700  
 + 
 +PCM->pcm_pll_ctrl4      = 0x00000015  
 + 
 +Set up PCM registers 
 + 
 +XDRV:pcm6368_timeslotAlloc 0xB0004040: 0x80000000 
 + 
 + 
 +Channel 0 assigned to timeslot 0 
 + 
 +XDRV:pcm6368_timeslotAlloc 0xB0004040: 0x89000000 
 + 
 + 
 +Channel 1 assigned to timeslot 1 
 + 
 +XDRV:pcm6368_timeslotAlloc 0xB0004040: 0x89A00000 
 + 
 + 
 +Channel 2 assigned to timeslot 2 
 + 
 +rxDescriptorArea      = 24  
 + 
 +txDescriptorArea      = 24  
 + 
 +Unaligned dmaRxDesc_c  = 0xA02D7000  
 + 
 +Unaligned dmaTxDesc_c  = 0xA02AC000  
 + 
 +rxBufferArea          = 1312  
 + 
 +txBufferArea          = 1312  
 + 
 +Unaligned dmaRxData  = 0xA02AD000  
 + 
 +Unaligned dmaTxData  = 0xA02A8000  
 + 
 +Aligned Tx Desc (0xA02AC000): chan 0, buf 0, sts 0xe000, len 640, bufp 0x2a8000  
 + 
 +Aligned Tx Desc (0xA02AC008): chan 0, buf 1, sts 0x7000, len 640, bufp 0x2a8290  
 + 
 +Aligned Rx Desc (0xA02D7000): chan 0, buf 0, sts 0x8000, len 640, bufp 0x2ad000  
 + 
 +Aligned Rx Desc (0xA02D7008): chan 0, buf 1, sts 0x9000, len 640, bufp 0x2ad290  
 + 
 +initIudma: chan 0, descBase 0xa02d7000, descBaseIudma 0x2d7000 
 + 
 +initIudma: chan 1, descBase 0xa02ac000, descBaseIudma 0x2ac000 
 + 
 +Enter TaskCreate CMT_EXCEPTION_IST 
 + 
 +TaskCreate - spawn new task CMT_EXCEPTION_IST 
 + 
 +Exit TaskCreate  
 + 
 +BHAL(ts: 23s 17 ms):DSP build date: Fri_Nov_6_2009_15:10:14 
 + 
 + 
 +regStatus (reg 12 sel 0)    = 0x10008501  
 + 
 +regStatus (reg 12 sel 7)    = 0x00000101  
 + 
 +regCause  (reg 13 sel 0)    = 0x00000000  
 + 
 +regCause  (reg 13 sel 7)    = 0x00808000  
 + 
 +regCMT    (reg 22 sel 0)    = 0xe31e1406  
 + 
 +regCMT    (reg 22 sel 1)    = 0x10008001  
 + 
 +XDRV:Kicking off secondary thread processor at entry point 0x8108C740 ... 
 + 
 + 
 +XDRV:Secondary thread processor entry point at 0x8108c740 
 + 
 + 
 +*** DSP TP: Entered main() *** 
 +XDRV:Thread processor handshake. Secondary app initialized properly. 
 + 
 + 
 +Enter TaskCreate HTSK 
 + 
 +TaskCreate - spawn new task HTSK 
 + 
 +Exit TaskCreate  
 + 
 +MSPI INITIALIZED 
 + 
 +SLIC reset pin: GPIO 32778  
 + 
 +SLIC reset pin: GPIO 32778  
 + 
 +SLIC chip select pin: GPIO 28  
 + 
 +Initializing 89116 device 0 ... 
 + 
 +--- 
 + 
 +SLIC: Starting 89116 device and line initializion... 
 + 
 +SLIC: Resetting device using GPIO 32778 ... 
 + 
 +SLIC: Reset applied on GPIO pin 32778SLIC: Initializing 89116 device 0 
 + 
 +BcmSpiReserveSlave <0,2,6250000>, spiStatus=0 
 + 
 +SLIC: Received VP_DEV_EVID_DEV_INIT_CMP event (i = 0) 
 + 
 +SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 1024  
 + 
 +SLIC: 89116 device 0 initialized OK 
 + 
 +SLIC: Initializing 89116 FXS line 
 + 
 +SLIC: Received VP_LINE_EVID_LINE_INIT_CMP event (i = 0) 
 + 
 +SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 2048  
 + 
 +SLIC: Received VP_EVID_CAL_CMP event (i= 120) 
 + 
 +SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 64  
 + 
 +SLIC: FXS line RX timeslot = 0  
 + 
 +SLIC: FXS line TX timeslot = 0  
 + 
 +SLIC: 89116 FXS line initialized OK 
 + 
 +SLIC: 89116 device 0 and FXS/FXO initializion COMPLETED OK ! 
 + 
 +--- 
 + 
 +Initializing 89316 device 0 ... 
 + 
 +--- 
 + 
 +SLICDAA: Starting 89316 device and line initializion... 
 + 
 +SLICDAA: Skipping SLIC chip reset 
 + 
 +SLICDAA: Initializing 89316 device 0 
 + 
 +SLIC: Received VP_DEV_EVID_DEV_INIT_CMP event (i = 0) 
 + 
 +SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 1024  
 + 
 +SLICDAA: 89316 device 0 initialized OK 
 + 
 +SLICDAA: Initializing 89316 FXS line 
 + 
 +SLIC: Received VP_LINE_EVID_LINE_INIT_CMP event (i = 0) 
 + 
 +SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 2048  
 + 
 +SLIC: Received VP_EVID_CAL_CMP event (i= 120) 
 + 
 +SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 64  
 + 
 +SLICDAA: FXS line RX timeslot = 2  
 + 
 +SLICDAA: FXS line TX timeslot = 2  
 + 
 +SLICDAA: 89316 FXS line initialized OK 
 + 
 +SLICDAA: Initializing 89316 FXO line 
 + 
 +SLICDAA: Locale 7 
 + 
 +SLICDAA: Locale 7 
 + 
 +SLICDAA: FXO line RX timeslot = 4  
 + 
 +SLICDAA: FXO line TX timeslot = 4  
 + 
 +SLICDAA: 89316 FXO line initialized OK 
 + 
 +SLICDAA: 89316 device 0 and FXS/FXO initializion COMPLETED OK ! 
 + 
 +--- 
 + 
 +BHAL(ts: 25s 845ms):COMPLETED Initializing board HAL 
 + 
 +boardHalInit completed 
 + 
 +Codec Support: PCMA/PCMU 
 + 
 +Codec Support: G722 
 + 
 +Codec Support: G729A 
 + 
 +Codec Support: G729B 
 + 
 +Codec Support: G723 
 + 
 +Codec Support: G726 
 + 
 +Codec Support: BV16 
 + 
 +Codec Support: BV32 
 + 
 +Codec Support: LINPCM128 
 + 
 +Codec Support: LINPCM256 
 + 
 +Codec Support: ILBC 
 + 
 +Codec Support: AMRNB 
 + 
 +Codec Support: AMRWB 
 + 
 +Codec Support: T.38 
 + 
 +Enter TaskCreate HRTBEAT 
 + 
 +TaskCreate - spawn new task HRTBEAT 
 + 
 +Exit TaskCreate  
 + 
 +HEARTBEAT: Initialized! 
 + 
 +Enter TaskCreate VRGEVPR 
 + 
 +TaskCreate - spawn new task VRGEVPR 
 + 
 +Exit TaskCreate  
 + 
 +Enter TaskCreate HCAS 
 + 
 +TaskCreate - spawn new task HCAS 
 + 
 +Exit TaskCreate  
 + 
 +gInterruptCounter    = 0x8115BEF4  
 +gInterruptErrors      = 0x811493F0  
 +gNextRxDesc          = 0x811493E4  
 +gNextTxDesc          = 0x811493E0  
 +32 ms ECAN tail-length 
 +*** gStartRxDesc[0] = 0xA02D7000  
 +*** gBufferSizeBytes = 640  
 +*** gStartTxDesc[0] = 0xA02AC000  
 +hal6368PcmInit 343 nextTxDesc = 0xA02AC000  
 +hal6368PcmInit 343 nextTxDesc = 0xA02AC008  
 +hal6368PcmInit 347 Ownership for TX desc not set. Use this buffer.  
 +DSP: Interrupt Masks 
 +--------------- 
 +IrqMask_high              = 0x00000707  
 +IrqMask                    = 0x0000A0B4  
 +IrqMask1_high              = 0x40000000  
 +IrqMask1                  = 0x00000000  
 +PCM_IUDMA->ctrl[0].intMask = 0x00000005  
 +PCM_IUDMA->ctrl[1].intMask = 0x00000005  
 + 
 +DSP: Interrupt Status 
 +----------------- 
 +IrqStatus_high            = 0x00000000  
 +IrqStatus                  = 0x00000040  
 +IrqStatus1_high            = 0x00000000  
 +IrqStatus1                = 0x00000040  
 +PCM_IUDMA->ctrl[0].intStat = 0x00000000  
 +PCM_IUDMA->ctrl[1].intStat = 0x00000000  
 +EPT(ts: 26s 185ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x50) of type: 0x0 
 + 
 +EPT(ts: 26s 313ms):Setting T.38 error correction mode for vhd 80 to 0x104 
 + 
 +EPT(ts: 26s 649ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x51) of type: 0x0 
 + 
 +EPT(ts: 26s 777ms):Setting T.38 error correction mode for vhd 81 to 0x104 
 + 
 +EPT(ts: 27s 112ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x52) of type: 0x0 
 + 
 +EPT(ts: 27s 240ms):Setting T.38 error correction mode for vhd 82 to 0x104 
 + 
 +EPT(ts: 27s 576ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x53) of type: 0x0 
 + 
 +EPT(ts: 27s 704ms):Setting T.38 error correction mode for vhd 83 to 0x104 
 + 
 +EndpointInit completed 
 + 
 + 
 +Enter vrgEndptCEPT(ts: 27s 872ms):endptConfigCIDModeParm classStmType = 2 
 + 
 + 
 +asTimeParamContrEPT(ts: 27s 879ms):ENDPT CREATE: Starting initialization for endpt 0 
 + 
 +ol... minHookFlaEPT(ts: 27s 886ms):EPTYPE_FXS 
 + 
 +sh = 300, maxHookFlash = 800. 
 +Codec Support: PCMA/PCMU 
 + 
 +Codec Support: G722 
 + 
 +Codec Support: G729A 
 + 
 +Codec Support: G729B 
 + 
 +Codec Support: G723 
 + 
 +Codec Support: G726 
 + 
 +Codec Support: BV16 
 + 
 +Codec Support: BV32 
 + 
 +Codec Support: LINPCM128 
 + 
 +Codec Support: LINPCM256 
 + 
 +Codec Support: ILBC 
 + 
 +Codec Support: AMRNB 
 + 
 +Codec Support: AMRWB 
 + 
 +Codec Support: T.38 
 + 
 +EPT(ts: 28s 45 ms):hdspVhdOpen Line VHD success. DSP 0, VHD (0x54) of type: 0x7 
 + 
 +HDSP(ts: 28s 63 ms):VHD 0x54: Frame size = 40, Mode = Narrowband 
 + 
 +HDSP(ts: 28s 88 ms):Switchboard ON (type Duplex): VHD 0x54/1 with VHD 0x0/0 
 + 
 +EPT(ts: 28s 95 ms):Default value for provItemId '608' did not exist 
 + 
 +EPT(ts: 28s 101ms):Default value for provItemId '600' did not exist 
 + 
 +SLIC: Mode for FXS channel changed to 1  
 + 
 +SLIC: Mode for FXS channel changed to 1  
 + 
 +EPT(ts: 28s 150ms):COMPLETED successful initialization for endpt 0 
 + 
 +00:00:28 SIGNAL: EPT(ts: 28s 156ms):SIGNAL: ept:0 cnx:-1 s:79 v:0 d:-1 p:-1 r:-1  
 + 
 +endpt 0, cnx -1,EPT(ts: 28s 163ms):COMPLETED SIGNAL 79 
 + 
 + evt 111 (TxGainEPT(ts: 28s 169ms):SIGNAL: ept:0 cnx:-1 s:80 v:0 d:-1 p:-1 r:-1  
 + 
 +), value 0 
 +00:0EPT(ts: 28s 176ms):COMPLETED SIGNAL 80 
 + 
 +0:28 SIGNAL: endEPT(ts: 28s 181ms):ENDPT CREATE: Starting initialization for endpt 1 
 + 
 +pt 0, cnx -1, evEPT(ts: 28s 188ms):EPTYPE_FXS 
 + 
 +t 112 (RxGain), value 0 
 +Codec Support: PCMA/PCMU 
 + 
 +Codec Support: G722 
 + 
 +Codec Support: G729A 
 + 
 +Codec Support: G729B 
 + 
 +Codec Support: G723 
 + 
 +Codec Support: G726 
 + 
 +Codec Support: BV16 
 + 
 +Codec Support: BV32 
 + 
 +Codec Support: LINPCM128 
 + 
 +Codec Support: LINPCM256 
 + 
 +Codec Support: ILBC 
 + 
 +Codec Support: AMRNB 
 + 
 +Codec Support: AMRWB 
 + 
 +Codec Support: T.38 
 + 
 +EPT(ts: 28s 344ms):hdspVhdOpen Line VHD success. DSP 0, VHD (0x55) of type: 0x7 
 + 
 +HDSP(ts: 28s 361ms):VHD 0x55: Frame size = 40, Mode = Narrowband 
 + 
 +HDSP(ts: 28s 386ms):Switchboard ON (type Duplex): VHD 0x55/1 with VHD 0x1/0 
 + 
 +EPT(ts: 28s 393ms):Default value for provItemId '608' did not exist 
 + 
 +EPT(ts: 28s 399ms):Default value for provItemId '600' did not exist 
 + 
 +SLICDAA: Mode for FXS channel changed to 1  
 + 
 +SLICDAA: Mode for FXS channel changed to 1  
 + 
 +EPT(ts: 28s 449ms):COMPLETED successful initialization for endpt 1 
 + 
 +00:00:28 SIGNAL: EPT(ts: 28s 457ms):SIGNAL: ept:1 cnx:-1 s:79 v:0 d:-1 p:-1 r:-1  
 + 
 +endpt 1, cnx -1,EPT(ts: 28s 464ms):COMPLETED SIGNAL 79 
 + 
 + evt 111 (TxGainEPT(ts: 28s 469ms):SIGNAL: ept:1 cnx:-1 s:80 v:0 d:-1 p:-1 r:-1  
 + 
 +), value 0 
 +00:0EPT(ts: 28s 477ms):COMPLETED SIGNAL 80 
 + 
 +0:28 SIGNAL: endpt 1, cnx -1, evt 112 (RxGain), value 0 
 + RTCP thread started with pid 1191  
 +00:00:28 rtpInit: RTCP task created, taskId = 10251 
 +00:00:28 CALLCLIENT: Initialization complete callSipClientMain 
 + 
 +Use default bin /var/console now ... 
 +------------------------------- 
 + 
 +-----Welcome to ATP Cli------ 
 + 
 +------------------------------- 
 + 
 + 
 + 
 +Login: admin 
 + 
 +Password:  
 + 
 +ATP> 
 +</code> 
 +</p> 
 +</HTML> 
 + 
 +==== OpenWrt bootlog ==== 
 +<HTML> 
 +<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF"> 
 +<code>[    0.000000] Linux version 3.10.34 (dani@tool) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40396) ) #18 SMP Wed Apr 30 19:58:28 CEST 2014 
 +[    0.000000] Detected Broadcom 0x6368 CPU revision b2 
 +[    0.000000] CPU frequency is 400 MHz 
 +[    0.000000] 64MB of RAM installed 
 +[    0.000000] registering 38 GPIOs 
 +[    0.000000] board_bcm963xx: Boot address 0xb8000000 
 +[    0.000000] board_bcm963xx: CFE version: 1.0.37-102.6 
 +[    0.000000] bootconsole [early0] enabled 
 +[    0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350) 
 +[    0.000000] board_bcm963xx: board name: HW65x 
 +[    0.000000] Determined physical RAM map: 
 +[    0.000000]  memory: 04000000 @ 00000000 (usable) 
 +[    0.000000] Initrd not found or empty - disabling initrd 
 +[    0.000000] Zone ranges: 
 +[    0.000000]  Normal  [mem 0x00000000-0x03ffffff] 
 +[    0.000000] Movable zone start for each node 
 +[    0.000000] Early memory node ranges 
 +[    0.000000]  node  0: [mem 0x00000000-0x03ffffff] 
 +[    0.000000] On node 0 totalpages: 16384 
 +[    0.000000] free_area_init_node: node 0, pgdat 802ffa00, node_mem_map 81000000 
 +[    0.000000]  Normal zone: 128 pages used for memmap 
 +[    0.000000]  Normal zone: 0 pages reserved 
 +[    0.000000]  Normal zone: 16384 pages, LIFO batch:3 
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. 
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes 
 +[    0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6592 r8192 d13888 u32768 
 +[    0.000000] pcpu-alloc: s6592 r8192 d13888 u32768 alloc=8*4096 
 +[    0.000000] pcpu-alloc: [0] 0 [0] 1  
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256 
 +[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) 
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) 
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) 
 +[    0.000000] Memory: 61268k/65536k available (2455k kernel code, 4268k reserved, 620k data, 248k init, 0k highmem) 
 +[    0.000000] Hierarchical RCU implementation. 
 +[    0.000000] NR_IRQS:256 
 +[    0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) 
 +[    0.032000] pid_max: default: 32768 minimum: 301 
 +[    0.036000] Mount-cache hash table entries: 512 
 +[    0.044000] SMP: Booting CPU1... 
 +[    0.048000] CPU revision is: 0002a031 (Broadcom BMIPS4350) 
 +[    0.048000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. 
 +[    0.048000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes 
 +[    0.080000] Synchronize counters for CPU 1: done. 
 +[    0.080000] SMP: CPU1 is running 
 +[    0.084000] Brought up 2 CPUs 
 +[    0.108000] NET: Registered protocol family 16 
 +[    0.116000] registering PCI controller with io_map_base unset 
 +[    0.132000] bio: create slab <bio-0> at 0 
 +[    0.136000] PCI host bridge to bus 0000:00 
 +[    0.140000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] 
 +[    0.144000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff] 
 +[    0.148000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] 
 +[    0.152000] pci 0000:00:01.0: [1814:3592] type 00 class 0x028000 
 +[    0.152000] pci 0000:00:01.0: reg 10: [mem 0xffff0000-0xffffffff] 
 +[    0.164000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold 
 +[    0.164000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 
 +[    0.164000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff] 
 +[    0.168000] Switching to clocksource MIPS 
 +[    0.176000] NET: Registered protocol family 2 
 +[    0.184000] TCP established hash table entries: 512 (order: 0, 4096 bytes) 
 +[    0.188000] TCP bind hash table entries: 512 (order: 0, 4096 bytes) 
 +[    0.196000] TCP: Hash tables configured (established 512 bind 512) 
 +[    0.204000] TCP: reno registered 
 +[    0.204000] UDP hash table entries: 256 (order: 1, 8192 bytes) 
 +[    0.212000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) 
 +[    0.220000] NET: Registered protocol family 1 
 +[    0.224000] PCI: CLS 0 bytes, default 16 
 +[    0.228000] squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +[    0.232000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
 +[    0.244000] msgmni has been set to 119 
 +[    0.248000] io scheduler noop registered 
 +[    0.252000] io scheduler deadline registered (default) 
 +[    0.260000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart 
 +[    0.268000] console [ttyS0] enabled, bootconsole disabled 
 +[    0.280000] bcm63xx-rng bcm63xx-rng: registered RNG driver 
 +[    0.288000] physmap platform flash device: 08000000 at 18000000 
 +[    0.296000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000 
 +[    0.304000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0 
 +[    0.304000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0 
 +[    0.304000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0 
 +[    0.304000] Amd/Fujitsu Extended Query Table at 0x0040 
 +[    0.312000]  Amd/Fujitsu Extended Query version 1.3. 
 +[    0.316000] number of CFI chips: 1 
 +[    0.320000] bcm63xxpart: CFE boot tag found with version 7 and board type HW65x 
 +[    0.328000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000 
 +[    0.336000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 10ff00 
 +[    0.340000] bcm63xxpart: Partition 2 is rootfs offset 130000 and length 690000 
 +[    0.348000] bcm63xxpart: Partition 3 is cal_data offset 7c0000 and length 10000 
 +[    0.356000] bcm63xxpart: Partition 4 is nvram offset 7f0000 and length 10000 
 +[    0.364000] bcm63xxpart: Partition 5 is linux offset 20000 and length 7a0000 
 +[    0.372000] bcm63xxpart: Spare partition is offset 700004 and length bfffc 
 +[    0.376000] 6 bcm63xxpart partitions found on MTD device physmap-flash.0 
 +[    0.384000] Creating 6 MTD partitions on "physmap-flash.0": 
 +[    0.392000] 0x000000000000-0x000000020000 : "CFE" 
 +[    0.396000] 0x000000020100-0x000000130000 : "kernel" 
 +[    0.404000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only 
 +[    0.420000] 0x000000130000-0x0000007c0000 : "rootfs" 
 +[    0.424000] mtd: device 2 (rootfs) set to be root filesystem 
 +[    0.432000] mtd: partition "rootfs_data" created automatically, ofs=0x700000, len=0xc0000 
 +[    0.440000] 0x000000700000-0x0000007c0000 : "rootfs_data" 
 +[    0.448000] 0x0000007c0000-0x0000007d0000 : "cal_data" 
 +[    0.456000] 0x0000007f0000-0x000000800000 : "nvram" 
 +[    0.464000] 0x000000020000-0x0000007c0000 : "linux" 
 +[    0.472000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) 
 +[    0.520000] b53_common: found switch: BCM63xx, rev 0 
 +[    0.524000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec 
 +[    0.540000] TCP: cubic registered 
 +[    0.540000] NET: Registered protocol family 17 
 +[    0.548000] 8021q: 802.1Q VLAN Support v1.8 
 +[    0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. 
 +[    0.568000] Freeing unused kernel memory: 248K (80312000 - 80350000) 
 +[    2.916000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex 
 +[    4.408000] usbcore: registered new interface driver usbfs 
 +[    4.416000] usbcore: registered new interface driver hub 
 +[    4.420000] usbcore: registered new device driver usb 
 +[    4.432000] Button Hotplug driver version 0.4.1 
 +[    4.500000] SCSI subsystem initialized 
 +[    4.516000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 
 +[    4.524000] ehci-platform: EHCI generic platform driver 
 +[    4.636000] ehci-platform ehci-platform: EHCI Host Controller 
 +[    4.640000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 
 +[    4.648000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500 
 +[    4.668000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored 
 +[    4.676000] hub 1-0:1.0: USB hub found 
 +[    4.680000] hub 1-0:1.0: 2 ports detected 
 +[    4.688000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver 
 +[    4.696000] ohci-platform ohci-platform: Generic Platform OHCI Controller 
 +[    4.704000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 
 +[    4.712000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600 
 +[    4.776000] hub 2-0:1.0: USB hub found 
 +[    4.780000] hub 2-0:1.0: 2 ports detected 
 +[    4.796000] usbcore: registered new interface driver usb-storage 
 +[    4.804000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0 
 +[    6.292000] jffs2: notice: (265) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 39 of xref (0 dead, 25 orphan) found. 
 +[    9.868000] NET: Registered protocol family 10 
 +[    9.900000] nf_conntrack version 0.5.0 (961 buckets, 3844 max) 
 +[    9.912000] ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +[    9.952000] fuse init (API version 7.22) 
 +[    9.964000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2 
 +[    9.972000] Backport generated by backports.git backports-20140221-0-g8e94650 
 +[    9.984000] ip_tables: (C) 2000-2006 Netfilter Core Team 
 +[  10.052000] usbcore: registered new interface driver ums-alauda 
 +[  10.060000] usbcore: registered new interface driver ums-cypress 
 +[  10.068000] usbcore: registered new interface driver ums-datafab 
 +[  10.080000] usbcore: registered new interface driver ums-freecom 
 +[  10.088000] usbcore: registered new interface driver ums-isd200 
 +[  10.096000] usbcore: registered new interface driver ums-jumpshot 
 +[  10.108000] usbcore: registered new interface driver ums-karma 
 +[  10.116000] usbcore: registered new interface driver ums-sddr09 
 +[  10.128000] usbcore: registered new interface driver ums-sddr55 
 +[  10.136000] usbcore: registered new interface driver ums-usbat 
 +[  10.168000] xt_time: kernel timezone is -0000 
 +[  10.212000] cfg80211: Calling CRDA to update world regulatory domain 
 +[  10.220000] cfg80211: World regulatory domain updated: 
 +[  10.224000] cfg80211:  DFS Master region: unset 
 +[  10.228000] cfg80211:  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) 
 +[  10.240000] cfg80211:  (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  10.248000] cfg80211:  (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  10.256000] cfg80211:  (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  10.264000] cfg80211:  (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  10.272000] cfg80211:  (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  10.280000] cfg80211:  (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) 
 +[  10.352000] PPP generic driver version 2.4.2 
 +[  10.360000] NET: Registered protocol family 24 
 +[  10.400000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) 
 +[  10.408000] rt2800pci 0000:00:01.0: setting latency timer to 64 
 +[  10.408000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00.eeprom'. 
 +[  10.420000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected 
 +[  10.428000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected 
 +[  10.436000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' 
 +[  14.032000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex 
 +[  17.588000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex 
 +[  17.600000] device eth0.1 entered promiscuous mode 
 +[  17.604000] device eth0 entered promiscuous mode 
 +[  17.612000] br-lan: port 1(eth0.1) entered forwarding state 
 +[  17.616000] br-lan: port 1(eth0.1) entered forwarding state 
 +[  18.612000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready 
 +[  18.812000] cfg80211: Calling CRDA for country: RO 
 +[  18.824000] cfg80211: Regulatory domain changed to country: RO 
 +[  18.828000] cfg80211:  DFS Master region: ETSI 
 +[  18.832000] cfg80211:  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) 
 +[  18.844000] cfg80211:  (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  18.852000] cfg80211:  (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  18.860000] cfg80211:  (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s) 
 +[  18.868000] cfg80211:  (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s) 
 +[  18.876000] cfg80211:  (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) 
 +[  19.620000] br-lan: port 1(eth0.1) entered forwarding state 
 +[  20.996000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin' 
 +[  21.172000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34 
 +[  21.272000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready 
 +[  21.280000] device wlan0-1 entered promiscuous mode 
 +[  21.532000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 
 +[  23.052000] wlan0: authenticate with b0:48:7a:d1:3d:a4 
 +[  23.080000] wlan0: send auth to b0:48:7a:d1:3d:a4 (try 1/3) 
 +[  23.088000] wlan0: authenticated 
 +[  23.096000] wlan0: associate with b0:48:7a:d1:3d:a4 (try 1/3) 
 +[  23.104000] wlan0: RX AssocResp from b0:48:7a:d1:3d:a4 (capab=0x431 status=0 aid=5) 
 +[  23.116000] wlan0: associated 
 +[  23.272000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready 
 +[  24.120000] br-lan: port 2(wlan0-1) entered forwarding state 
 +[  24.124000] br-lan: port 2(wlan0-1) entered forwarding state 
 +[  24.132000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready 
 +[  26.128000] br-lan: port 2(wlan0-1) entered forwarding state 
 +</code> 
 +</p> 
 +</HTML> 
 + 
 + 
 +===== Notes =====
[[http://huaweihg612hacking.wordpress.com]] Very nice collection of info, the hg612 is very similar [[http://huaweihg612hacking.wordpress.com]] Very nice collection of info, the hg612 is very similar
Line 140: Line 2132:
Datasheet [[http://huaweiservis.net/dosya/HUAWEI-HG655d-datasheet.pdf]] Datasheet [[http://huaweiservis.net/dosya/HUAWEI-HG655d-datasheet.pdf]]
 +
 +==== BCM tag ====
 +
 +''Tag Version -----------> : 7
 +Signature 1 -----------> : Broadcom Corporatio
 +Signature 2 -----------> : ver. 2.0
 +Chip ID ---------------> : 6368
 +Board ID --------------> : HW65x
 +Bigendian -------------> : true
 +Image size ------------> : 005b226c, 5972588
 +CFE Address -----------> : 00000000, 0
 +CFE Length ------------> : 00000000, 0
 +Flash Root Address ----> : bfc20100, 3217162496
 +Flash Root Length -----> : 004d4000, 5062656
 +Flash Kernel Address --> : c00f4100, 3222225152
 +Flash Kernel Length ---> : 000de26c, 909932
 +Vendor information ----> :
 +Compile Information ---> : HG655bV100R001C02B0
 +Image CRC -------------> : f9c4cb2a  [Computed Value: f9c4cb2a]
 +Header CRC ------------> : ed34bdfb  [Computed Value: ed34bdfb]
 +Kernel CRC ------------> : 4d04fb6f  [Computed Value: 4d04fb6f]
 +Rootfs CRC ------------> : 80e314ce  [Computed Value: 80e314ce]''
 +
 +==== Wifi calibration data ====
 +<code>007C:0000 | 62 30 01 00  72 D1 5E 0D  AD 6C 62 30  14 18 01 80 | b0..rÑ^.­lb0....
 +007C:0010 | 00 00 62 30  14 18 00 00  01 00 6A FF  0C 00 FF FF | ..b0......jÿ..ÿÿ
 +007C:0020 | FF FF FF FF  B0 92 FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿ°.ÿÿÿÿÿÿÿÿÿÿ
 +007C:0030 | FF FF FF FF  22 08 24 00  FF FF 16 01  FF FF D9 FA | ÿÿÿÿ".$.ÿÿ..ÿÿÙú
 +007C:0040 | CC 88 FF FF  0D FF 00 00  03 00 00 00  00 00 FF FF | Ì.ÿÿ.ÿ........ÿÿ
 +007C:0050 | FF FF 0E 0F  0F 0F 10 10  10 10 10 0F  0F 0F 0F 0F | ÿÿ..............
 +007C:0060 | 0C 0C 0C 0C  0C 0C 0C 0C  0C 0B 0B 0B  0B 0B FF FF | ..............ÿÿ
 +007C:0070 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0080 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0090 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:00A0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:00B0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:00C0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:00D0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF 55 55 | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿUU
 +007C:00E0 | 88 88 77 77  66 66 66 66  66 66 66 66  66 66 66 66 | ..wwffffffffffff
 +007C:00F0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0100 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0110 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0120 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0130 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0140 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0150 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0160 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0170 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0180 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:0190 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:01A0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:01B0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:01C0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:01D0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:01E0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF | ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
 +007C:01F0 | FF FF FF FF  FF FF FF FF  FF FF FF FF  FF 06 86 93 | ÿÿÿÿÿÿÿÿÿÿÿÿÿ...
 +</code>
===== Tags ===== ===== Tags =====
For some Help with the Tags, please have a look here: [[meta/tags]] For some Help with the Tags, please have a look here: [[meta/tags]]
-{{tag>bcm63xx bcm6368 FastEthernet 4Port 1USB ADSL2+ VDSL2 64RAM 8Flash fxo MIPS MIPS32}}+{{tag>bcm63xx bcm6368 FastEthernet 4Port hwVLAN 1USB 1WNIC 802.11bgn 64RAM 8Flash MIPS MIPS32 TRNG}} 
 + 

Back to top

toh/huawei/hg655d.1373022898.txt.bz2 · Last modified: 2013/07/05 13:14 (external edit)