User Tools

Site Tools


toh:linksys:ag241

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
toh:linksys:ag241 [2014/08/15 21:54]
m3m3nt0 added Flash Layout
toh:linksys:ag241 [2015/12/14 20:11] (current)
tmomas New bootlog formatting applied
Line 1: Line 1:
 +====== Linksys AG241 ======
  
 +The Linksys AG241 is an ADSL gateway without wireless acccess point. See [[oldwiki/​openwrtdocs/​hardware/​linksys/​ag241]]
 +
 +{{page>​meta:​infobox:​construction&​noheader&​nofooter&​noeditbtn}}
 +
 +====== Supported Versions ======
 +^ Version/​Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^
 +| AG241 v1  |  :?:  |  -  |  Supported ​ | - |
 +| AG241 v2  |  :?:  |  -  |  Kamikaze 8.09.2 ​ | - |
 +| ::: | ::: | ::: |  Backfire 10.03.1 ​ | LAN switch is not correctly recognized |
 +| ::: | ::: | ::: |  Attitude Adjustment 12.09  | LAN switch is not correctly recognized |
 +| AG241 v2b  |  :?:  |  -  |  Supported ​ | - |
 +
 +**NOTE:** Actually on //Backfire 10.03.1//, //Attitude Adjustment 12.09// and //trunk (r39422)// the default network configuration won't work. [[https://​forum.openwrt.org/​viewtopic.php?​id=48631|forum topic]]
 +
 +OEM source code available at: [[http://​support.linksys.com/​en-eu/​gplcodecenter]]
 +
 +===== Hardware Highlights =====
 +^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
 +| Texas Instruments TNETD7200ZDW@ 211.97 MHz | 16MiB | 4MiB | 4 x 1 | No | Yes | :?: |
 +
 +Manufacturer'​s site: [[http://​support.linksys.com/​en-eu/​support/​gateways/​AG241]]
 +
 +Forum: [[https://​forum.openwrt.org/​viewtopic.php?​id=48631]]
 +
 +===== Installation =====
 +  - → [[doc:​howto:​obtain.firmware]] **AG241v1** for AG241 v1, **AG241v2** for v2 and **AG241v2b** for AG241 v2 Annex B
 +  - → [[doc:​howto:​generic.flashing|Install OpenWrt]]
 +  - → [[about/​latest|Latest OpenWrt release]]
 +
 +FIXME
 +
 +==== Flash Layout ====
 +Please check out the article [[doc:​techref:​Flash.Layout]]. It contains an example and a couple of explanations.
 +
 +^ partition ^ start ^ end ^ Name ^
 +| mtd0 | 0x900e0000 | 0x903d0000 | mtd0 |
 +| mtd1 | 0x90020000 | 0x903d0000 | mtd1 |
 +| mtd2 | 0x90000000 | 0x90020000 | mtd2 |
 +| mtd3 | 0x903f0000 | 0x90400000 | mtd3 |
 +| mtd4 | 0x903d0000 | 0x903f0000 | mtd4 |
 +
 +==== OEM installation using the TFTP method ====
 +
 +  * → [[doc:​howto:​generic.flashing.tftp]]
 +  * → [[doc:​techref:​bootloader:​pspboot#​tftp.flashing]]
 +
 +=== Specific values you need ===
 +
 +| Bootloader tftp server IPv4 address | 192.168.1.1 |
 +| Firmware tftp image | [[about/​latest|Latest OpenWrt release]] named //​upgrade_code.bin//​ |
 +| TFTP Transfer Window | 1 seconds |
 +| TFTP Window Start | approximately 2 seconds after power on; just after LAN leds lights up all together |
 +
 +===== Basic configuration =====
 +-> [[doc:​howto:​basic.config|Basic configuration]] After flashing, proceed with this.\\
 +
 +==== Failsafe mode ====
 +-> [[doc:​howto:​generic.failsafe]]
 +
 +Press ''​f''​ and hit ''​Enter''​ when asked during boot. (you will need a [[#Serial]] console to see it)
 +
 +===== Hardware ======
 +
 +==== Info ====
 +AG241 v2
 +
 +| **[[wp>​Instruction set]]:​** ​              | [[wp>​MIPS architecture|MIPS]] |
 +| **Vendor:​** ​                              | [[wp>​Texas Instruments]] |
 +| **[[doc:​techref:​Bootloader]]:​** ​          | [[doc:​techref:​bootloader:​PSPBoot]] |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | [[http://​focus.ti.com/​lit/​ml/​spat013a/​spat013a.pdf|TNETD7200ZDW]] |
 +| **[[doc:​hardware:​cpu|CPU]] @Frq** ​        | MIPS 4KEc V4.8 @ 211.97 MHz |
 +| **Flash size:​** ​                | 4 MB |
 +| **Flash Chip:​** ​                | {{:​media:​datasheets:​flash:​mx29lv320ct-b-1.0.pdf|}} |
 +| **RAM size:​** ​                  | 16 MB   |
 +| **RAM Chip:​** ​                  | [[http://​openwag200.sourceforge.net/​pdf/​p2v28s_0btp11_07024.pdf|MIRA P2V28S40BTP]] |
 +| **[[doc:​hardware:​Switch]]:​** ​   | [[http://​www.datasheetarchive.com/​dl/​Datasheets-IS17/​DSA00321375.pdf|Infineon ADM6996LC]] |
 +| **[[doc/​hardware/​internet.access.technologies|Modem]]:​** ​  | xDSL |
 +| **USB:​** ​                       | No |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​ | [[#​Serial|Yes]] |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​     | :?: |
 +
 +==== Photos ====
 +AG241 v2
 +
 +//Front://
 +
 +FIXME
 +
 +//Back://
 +
 +FIXME
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +  *Remove two screws under the front rubber feet
 +  *Press the two sides of the router and pull the blue part to release the plastic hooks 
 +
 +//Main PCB//
 +
 +{{:​oldwiki:​openwrtdocs:​hardware:​linksys:​ag241-eu.jpg?​250}}
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +Serial console can be plugged to JP4: connector lacks, it has to be soldered on the board.
 +
 +Since your router is working at 3.3V ([[wp>​Transistor–transistor logic|TTL]] level voltage), you'll need [[doc:​hardware:​port.serial#​usb.to.rs232.ttl.converter.module|USB to RS232 TTL converter]] or a level shifter such as a Maxim MAX232 to change the level from 3.3V to your computer level which is usually at 12V.
 +You cannot plug directly those pins to your pc serial port (or serial adapter): you will certainly fry the serial circuit or even the whole board :!:
 +
 +How to connect to the Serial Port of this specific device:
 +
 +{{:​oldwiki:​openwrtdocs:​hardware:​linksys:​serial_console_pins_ttl.jpg?​250}}
 +
 +^ Pin   ^ Signal ​  ^
 +| 1     | GND      |
 +| 2     | n/a      |
 +| 3     | RxD      |
 +| 4     | TxD      |
 +| 5     | VCC      |
 +
 +The settings for terminal are: 38400 bauds, 8 bits, no parity, 1 stop bit (**38400 8N1**)
 +
 +^ terminal configuration ​  ^^
 +| Bits per second ​         | 38400|
 +| Data bits                | 8|
 +| Parity ​                  | None|
 +| Stop bits                | 1|
 +| Flow control ​            | None|
 +
 +===== Debricking =====
 +  * → [[doc:​howto:​generic.debrick]]
 +  * → [[doc:​techref:​bootloader:​pspboot#​tftp.flashing]]
 +
 +You can //debrick// your device using a TFTP client to upload the firmware image to the router during the booting process (also without a serial console!! -> see below)
 +
 +You will need:
 +
 +  * [[wp>​TFTP]] client (probably preinstalled in your Linux distro)
 +  * terminal emulation program (like [[wp>​minicom]])
 +
 +The method is based on pausing the booting process and send the firmware //.bin// image to the router through tftp: it will receive it, install and reboot.
 +
 +  - Setup your ethernet network adapter with a static/​fixed IP address (the router will respond on 192.168.1.1)
 +  - Connect your PC to one of the router'​s LAN ports
 +  - Start your terminal emulation program and configure it as described in section [[#​Serial|Serial]]
 +  - Turn on the router
 +  - When you see the line <​file>​Press ESC for monitor...</​file>​ press ESC key: this will stop the booting process and enter //debug mode//
 +  - Start your tftp client and connect to the router
 +  - Send the firmware image in **binary mode** (octet) and named as **upgrade_code.bin** ​
 +
 +
 +
 +
 +This little //how to// is based on [[http://​cyberstorm.altervista.org/​wag354g/​guides/​howto_unbricking_wag354g_en.txt|this guide]] written by Marco Vedovati and released under [[http://​creativecommons.org/​licenses/​by-nc-sa/​2.5/​|Creative Commons Attribution-NonCommercial-ShareAlike 2.5]]
 +
 +
 +===== Bootlogs =====
 +==== OEM bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​free space start: 0xb0010000
 +free space end: 0xb0400000
 +
 +Basic POST completed... ​    ​Success.
 +Last reset cause: Software reset (memory controller also reset)
 +
 +PSPBoot1.3 rev: 0.22.19.5
 +CyberTAN rev: 0.22.19
 +(c) Copyright 2002-2005 Texas Instruments,​ Inc. All Rights Reserved.
 +
 +FlashType:
 +
 +mac_init(): Find mac [00:​18:​F8:​61:​8E:​44] in location 0
 +Find mac [00:​18:​F8:​61:​8E:​44] in location 0
 +mac_value: 00:​18:​F8:​61:​8E:​44
 +Press ESC for monitor... 321
 +
 +(psbl) ​
 +
 +Booting...
 +Launching kernel decompressor.
 +Starting LZMA Uncompression Algorithm.
 +Copyright (C) 2003 Texas Instruments Incorporated;​ Copyright (C) 1999-2003 Igor Pavlov.
 +Compressed file is LZMA format.
 +Kernel decompressor was successful ... launching kernel.
 +
 +LINUX started...
 +Config serial console: ttyS0,38400
 +Auto Detection OHIO chip
 +This SOC has MDIX cababilities on chip.
 +WLAN 1350 chip configured.
 +CONFIG_AVALANCHE_VLYNQ_POLARITY_LOW
 +Failed to initialize the vlynq @ 0xa8611800.
 +The error msg: Error in configuring clocks..
 +CPU revision is: 00018448
 +Primary instruction cache 16kb, linesize 16 bytes (4 ways)
 +Primary data cache 8kb, linesize 16 bytes (4 ways)
 +Number of TLB entries 16.
 +Linux version 2.4.17_mvl21-malta-mips_fp_le (root@localhost.localdomain) (gcc version 2.95.3 20010315 (release/​MontaVista)) #31 Thu Jul 12 20:29:16 CST 2007
 +Determined physical RAM map:
 + ​memory:​ 14000000 @ 00000000 (reserved)
 + ​memory:​ 00020000 @ 14000000 (ROM data)
 + ​memory:​ 00fe0000 @ 14020000 (usable)
 +On node 0 totalpages: 4096
 +zone(0): 4096 pages.
 +zone(1): 0 pages.
 +zone(2): 0 pages.
 +Kernel command line: 
 +calculating r4koff... 00102c00(1059840)
 +CPU frequency 211.97 MHz
 +Calibrating delay loop... 211.35 BogoMIPS
 +Freeing Adam2 reserved memory [0x14001000,​0x0001f000]
 +Memory: 13880k/​16384k available (1882k kernel code, 2504k reserved, 139k data, 64k init)
 +Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
 +Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
 +Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
 +Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Checking for '​wait'​ instruction... ​ unavailable.
 +POSIX conformance testing by UNIFIX
 +Linux NET4.0 for Linux 2.4
 +Based upon Swansea University Computer Society NET3.039
 +TI Optimizations:​ Allocating TI-Cached Memory Pool.
 +Warning: Number of buffers is not configured.Setting default to 512
 +Using 512 Buffers for TI-Cached Memory Pool.
 +DEBUG: Using Hybrid Mode.
 +NSP Optimizations:​ Succesfully allocated TI-Cached Memory Pool.
 +Initializing RT netlink socket
 +Starting kswapd
 +Disabling the Out Of Memory Killer
 +devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
 +devfs: boot_options:​ 0x1
 +pty: 32 Unix98 ptys configured
 +Serial driver version 5.05c (2001-07-08) with no serial options enabled
 +ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
 +block: 64 slots per queue, batch=16
 +CPMAC Auto Detect Enabled: detected external PHY and external switch as well..
 +Error getting CPMAC Configuration params for instance:0
 +Environment Variable:​MACCFG_A not set in bootloader
 +Setting Default configuration params for CPMAC instance:0
 +Default Asymmetric MTU for eth0 1500
 +TI CPMAC Linux DDA version 1.8 - CPMAC DDC version 0.2
 +Cpmac: Installed 1 instances.
 +Cpmac driver is allocating buffer memory at init time.
 +PPP generic driver version 2.4.1
 +avalanche flash device: 0x400000 at 0x10000000.
 + ​Amd/​Fujitsu Extended Query Table v1.1 at 0x0040
 +Physically mapped flash: Swapping erase regions for broken CFI table.
 +number of CFI chips: 1
 +Looking for mtd device :mtd0:
 +Found a mtd0 image (0xe0000), with size (0x2f0000).
 +Looking for mtd device :mtd1:
 +Found a mtd1 image (0x20000), with size (0x3b0000).
 +Looking for mtd device :mtd2:
 +Found a mtd2 image (0x0), with size (0x20000).
 +Looking for mtd device :mtd3:
 +Found a mtd3 image (0x3f0000), with size (0x10000).
 +Looking for mtd device :mtd4:
 +Found a mtd4 image (0x3d0000), with size (0x20000).
 +Creating 5 MTD partitions on "​Physically mapped flash":​
 +0x000e0000-0x003d0000 : "​mtd0"​
 +0x00020000-0x003d0000 : "​mtd1"​
 +0x00000000-0x00020000 : "​mtd2"​
 +0x003f0000-0x00400000 : "​mtd3"​
 +0x003d0000-0x003f0000 : "​mtd4"​
 +NET4: Linux TCP/IP 1.0 for NET4.0
 +IP Protocols: ICMP, UDP, TCP, IGMP
 +IP: routing cache hash table of 512 buckets, 4Kbytes
 +TCP: Hash tables configured (established 1024 bind 1024)
 +IPv4 over IPv4 tunneling driver
 +Default Asymmetric MTU for tunl0 1480
 +GRE over IPv4 tunneling driver
 +Default Asymmetric MTU for gre0 1476
 +Linux IP multicast router 0.06 plus PIM-SM
 +klips_info:​ipsec_init:​ KLIPS startup, FreeS/WAN IPSec version: super-freeswan-1.99.8
 +Default Asymmetric MTU for ipsec0 0
 +Default Asymmetric MTU for ipsec1 0
 +Default Asymmetric MTU for ipsec2 0
 +Default Asymmetric MTU for ipsec3 0
 +Default Asymmetric MTU for ipsec4 0
 +klips_info:​ipsec_alg_init:​ KLIPS alg v=0.8.1-0 (EALG_MAX=255,​ AALG_MAX=15)
 +klips_info:​ipsec_alg_init:​ calling ipsec_alg_static_init()
 +ipsec_1des_init(alg_type=15 alg_id=2 name=1des): ret=0
 +You should NOT load 1DES support except for testing purposes !
 +ipsec_null_init(alg_type=15 alg_id=11 name=null): ret=0
 +ip_conntrack version 2.0 (128 buckets, 1024 max) - 392 bytes per conntrack
 +ip_tables: (c)2000 Netfilter core team
 +netfilter PSD loaded - (c) astaro AG
 +NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
 +NET4: Ethernet Bridge 008 for NET4.0
 +Initializing the WAN Bridge.
 +Please set the MAC Address for the WAN Bridge.
 +Set the Environment variable '​wan_br_mac'​. ​
 +MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
 +802.1Q VLAN Support v1.6  Ben Greear <​greearb@candelatech.com>​
 +vlan Initialization complete.
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Mounted devfs on /dev
 +Freeing unused kernel memory: 64k freed
 +Firmware Version: 2.01.03
 +ret = -1
 +www -> /www
 +mount: Invalid argument
 +Hit enter to continue...killall:​ httpd: no process killed
 +
 + ​Configured 19 states ​
 +now insmod tiatm
 +Using /​lib/​modules/​2.4.17_mvl21-malta-mips_fp_le/​kernel/​drivers/​atm/​tiatm.o
 +name=[eth0] lan_ifname=[br0]
 +=====> set br0 hwaddr to eth0
 +wlconf: No such file or directory
 +Lan Ipaddr: 255.255.255.0 Netmask: 255.255.255.0................
 +255.255.255.0 255.255.255.0
 +.............list ​ ..............
 +antsel: No such file or directory
 +[HTTPD Starting on /www]
 +The boot is UNKNOWN
 +tftp server started
 +tftpd: standalone socket
 +HTTPD start, ​ port 80
 +dhcpd:​auto_search_ip=0,​firstsetlanip=1
 +.............list ​ ..............
 +info, udhcp server (v0.9.8) started
 +log_ipaddr=255
 +killall: leijun--upnpd-igd ver 0.83 2004-0329: no process killed
 +Now Start syslog.........................!!zebra disabled
 +killall: adslpolling:​ no process killed
 +IDLE
 +Hit enter to continue...wan def hwaddr 00:​18:​F8:​61:​8E:​45
 +polling now .......
 +upnpd-igd:​current select wan connection:​0
 +upnp_content_num_0 = 14
 +killall: begin_now: no process killed</​nowiki>​
 +</​WRAP>​\\
 +
 +==== OpenWrt bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​Linux version 2.6.26.8 (agb@arrakis) (gcc version 4.1.2) #1 Wed Dec 2 15:14:35 UTC 2009
 +console [early0] enabled
 +CPU revision is: 00018448 (MIPS 4KEc)
 +Clocks: Async mode
 +Clocks: Setting DSP clock
 +Clocks: prediv: 1, postdiv: 1, mul: 5
 +Clocks: base = 25000000, frequency = 125000000, prediv = 1, postdiv = 2, postdiv2 = 1, mul = 10
 +Clocks: Setting CPU clock
 +Adjusted requested frequency 211000000 to 211968000
 +Clocks: prediv: 1, postdiv: 1, mul: 6
 +Clocks: base = 35328000, frequency = 211968000, prediv = 1, postdiv = 1, postdiv2 = -1, mul = 6
 +Clocks: Setting USB clock
 +Adjusted requested frequency 48000000 to 48076920
 +Clocks: prediv: 13, postdiv: 1, mul: 5
 +Clocks: base = 125000000, frequency = 48000000, prediv = 13, postdiv = 1, postdiv2 = -1, mul = 5
 +TI AR7 (TNETD7200),​ ID: 0x002b, Revision: 0x10
 +Determined physical RAM map:
 + ​memory:​ 01000000 @ 14000000 (usable)
 +Entering add_active_range(0,​ 81920, 86016) 0 entries of 256 used
 +Initrd not found or empty - disabling initrd
 +Zone PFN ranges:
 +  Normal ​     81920 ->    86016
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0:    81920 ->    86016
 +On node 0 totalpages: 4096
 +  Normal zone: 32 pages used for memmap
 +  Normal zone: 0 pages reserved
 +  Normal zone: 4064 pages, LIFO batch:0
 +  Movable zone: 0 pages used for memmap
 +Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
 +Kernel command line: init=/​etc/​preinit rootfstype=squashfs,​jffs2,​ console=ttyS0,​38400n8
 +Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
 +PID hash table entries: 64 (order: 6, 256 bytes)
 +Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
 +Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +Memory: 12560k/​16384k available (2001k kernel code, 3824k reserved, 417k data, 124k init, 0k highmem)
 +SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0,​ CPUs=1, Nodes=1
 +Calibrating delay loop... 211.35 BogoMIPS (lpj=1056768)
 +Mount-cache hash table entries: 512
 +net_namespace:​ 644 bytes
 +NET: Registered protocol family 16
 +Switched to high resolution mode on CPU 0
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 512 (order: 0, 4096 bytes)
 +TCP bind hash table entries: 512 (order: -1, 2048 bytes)
 +TCP: Hash tables configured (established 512 bind 512)
 +TCP reno registered
 +NET: Registered protocol family 1
 +squashfs: version 3.0 (2006/​03/​15) Phillip Lougher
 +Registering mini_fo version $Id$
 +JFFS2 version 2.2. (NAND) (SUMMARY) ​ © 2001-2006 Red Hat, Inc.
 +msgmni has been set to 24
 +io scheduler noop registered
 +io scheduler deadline registered (default)
 +Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
 +serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a TI-AR7
 +console handover: boot [early0] -> real [ttyS0]
 +Fixed MDIO Bus: probed
 +cpmac-mii: probed
 +cpmac: device eth0 (regs: 08610000, irq: 27, phy: , mac: 00:​18:​f8:​61:​8e:​44)
 +physmap platform flash device: 00800000 at 10000000
 +physmap-flash.0:​ Found 1 x16 devices at 0x0 in 16-bit bank
 +physmap-flash.0:​ Found an alias at 0x400000 for the chip at 0x0
 + ​Amd/​Fujitsu Extended Query Table at 0x0040
 +physmap-flash.0:​ Swapping erase regions for broken CFI table.
 +number of CFI chips: 1
 +cfi_cmdset_0002:​ Disabling erase-suspend-program due to code brokenness.
 +cmdlinepart partition parsing not available
 +RedBoot partition parsing not available
 +4 ar7part partitions found on MTD device physmap-flash.0
 +Creating 4 MTD partitions on "​physmap-flash.0":​
 +0x00000000-0x00010000 : "​loader"​
 +0x00010000-0x00020000 : "​config"​
 +0x00020000-0x00400000 : "​linux"​
 +0x000f0000-0x00400000 : "​rootfs"​
 +mtd: partition "​rootfs"​ set to be root filesystem
 +mtd: partition "​rootfs_data"​ created automatically,​ ofs=290000, len=170000 ​
 +0x00290000-0x00400000 : "​rootfs_data"​
 +ar7_wdt: disabling watchdog timer
 +ar7_wdt: timer margin 59 seconds (prescale 65535, change 57180, freq 62500000)
 +Registered led device: status
 +vlynq0: regs 0x08611800, irq 29, mem 0x04000000
 +TCP vegas registered
 +NET: Registered protocol family 17
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing unused kernel memory: 124k freed
 +Please be patient, while OpenWrt loads ...
 +Algorithmics/​MIPS FPU Emulator v1.5
 +mini_fo: using base directory: /
 +mini_fo: using storage directory: /tmp/root
 +br-lan: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
 +device eth0 entered promiscuous mode
 +br-lan: port 1(eth0) entering learning state
 +br-lan: topology change detected, propagating
 +br-lan: port 1(eth0) entering forwarding state
 +PHY: 0:1f - Link is Down
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +PPP generic driver version 2.4.2
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
 +acx: this driver is still EXPERIMENTAL
 +acx: reading README file and/or Craig'​s HOWTO is recommended,​ visit http://​acx100.sf.net in case of further questions/​discussion
 +acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
 +acx: running on a little-endian CPU
 +acx: PCI/VLYNQ module v0.3.37 initialized,​ waiting for cards to probe...
 +Not using the 00000009 VLYNQ device'​s driver for VLYNQ device: 00000000
 +Not using the 00000029 VLYNQ device'​s driver for VLYNQ device: 00000000
 +registered device TI Avalanche SAR
 +Ohio250(7200/​7100A2) detected
 +requesting firmware image "​ar0700xx.bin"​
 +firmware: requesting ar0700xx.bin
 +avsar firmware released
 +tn7dsl_set_modulation : Setting mode to 0x1
 +Creating new root folder avalanche in the proc for the driver stats 
 +Texas Instruments ATM driver: version:​[7.03.01.00]
 +jffs2_scan_eraseblock():​ End of filesystem marker found at 0x0
 +jffs2_build_filesystem():​ unlocking the mtd device... done.
 +jffs2_build_filesystem():​ erasing all blocks after the end marker... done.
 +mini_fo: using base directory: /
 +mini_fo: using storage directory: /jffs
 +ar7_wdt: enabling watchdog timer</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Notes =====
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​infineon ADM6996LC ar7 adsl2+}}