User Tools

Site Tools


toh:linksys:e1000

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
toh:linksys:e1000 [2013/01/16 08:35]
hhm updates chu
toh:linksys:e1000 [2014/02/24 09:13] (current)
hhm
Line 2: Line 2:
  
 ^ Version/​Model ^ CPU ^ RAM ^ Flash ^ Network ^ USB ^ Serial ^ JTAG ^ Bootloader ^ OpenWrt Version Supported ^  ^ Version/​Model ^ CPU ^ RAM ^ Flash ^ Network ^ USB ^ Serial ^ JTAG ^ Bootloader ^ OpenWrt Version Supported ^ 
-| v1   ​| ​ Broadcom 47162@300MHz | 32MB | 4MB | 4x1 | No | Yes | ? | CFE | Trunk (WIP[[#​fine.print|*]]) |+| v1   ​| ​ Broadcom 47162@300MHz | 32MB | 4MB | 4x1 | No | Yes | ? | CFE | Barrier Breaker trunk (WIP[[#​fine.print|*]]) |
 | v2   | | v2   |
 == Fine print == == Fine print ==
-* At time of writing this (2013/jan) a firmware image needs to be built from scratch with an option enabled and a patch in order for networking to function properly; see [[https://​forum.openwrt.org/​viewtopic.php?​pid=188754#​p188754|this forum post]] for instructions.+  ​* At time of writing this (2013/jan) a firmware image needs to be built from scratch with an option enabled and a patch in order for networking to function properly; see [[https://​forum.openwrt.org/​viewtopic.php?​pid=188754#​p188754|this forum post]] for instructions. 
 +  * update (2013/feb) now the wired drivers work out of the box, but enabling wireless currently ​ disables the wired networking until the wireless is disabled once again, so locking oneself out of the wireless can BRICK the device ([[doc:​howto:​generic.failsafe|failsafe]] may work, but I do not know if it is working (yet) on this device)! 
 +  * update (2013/jun) see [[https://​forum.openwrt.org/​viewtopic.php?​pid=201025#​p201025|this]] for more info 
 +  * update (2013/sep) working, use at your own risk, not enough room on device to install Luci 
 +  * update (2014/feb) see [[https://​forum.openwrt.org/​viewtopic.php?​pid=226138#​p226138|this]] for more info
    
- 
  
 ===== V1 ===== ===== V1 =====
-An 802.11n router; has same hardware as [[.:​WRT160N|Linksys WRT160Nv3]] and [[..:​cisco:​M10|Cisco Valet M10 v1]].+The first version is an 802.11n router; has same hardware as [[.:​WRT160N|Linksys WRT160Nv3]] and [[..:​cisco:​M10|Cisco Valet M10 v1]].
  
 ==== Installation ==== ==== Installation ====
-Uses the brcm47xx generic .trx firware image.+The version below does not load LuCi, you can still get a DHCP address and SSH in. 
 + 
 +Do this at YOUR OWN RISK, the current snapshot of trunk may be broken! It may be better to wait until the next stable release. 
 + 
 +Use the brcm47xx generic .trx firware image, or see if the BIN image worksSee details below. 
 + 
 +The most recent trunk WIP snapshot builds can be found at [[http://​downloads.openwrt.org/​snapshots/​trunk/​brcm47xx/​]]
  
-TFTP flashing initiated ​via serial works, "flash -noheader ​flash1.trx" ​at CFE prompt.+OEM easy installation (aka via original firmware)Not yet (since the wired networking drivers are not included in the stock firmware builds ​at time of writing this, and wireless is locked by default in the regular builds as far as I know.)
  
-OEM easy installation:​ Not yet (since the wired networking drivers are not included in the stock firmware ​builds at time of writing thisand wireless ​is locked by default in the regular builds as far as I know.)+  * Update ​(2013/feb): The firmware can be flashed by updating to DD-WRT first, and then uploading with the DD-WRT firmware update feature (Reason: The stock firmware ​currently requires [[doc:​techref:​header|a BIN imagenot a TRX]].) See [[#​fine.print|fine print]] for notices. 
 +  * Update (2013/sep): There is now a BIN formatted image, to be used for OEM easy installation,​ called "​openwrt-e1000_v1_v2-squashfs.bin". However, I am not sure if it works (correctly, or at all).
  
-OEM installation using the TFTP method: Does not work, because of some kind of misconfiguration in the bootloader; use serial-initiated TFTP flashing instead.+OEM installation using the TFTP method: Does not work, because of some kind of misconfiguration in the bootloader; use serial-initiated TFTP flashing instead ​(REQUIRES TTL SERIAL ACCESS).
  
 +TFTP flashing initiated via serial: works; <​code>​flash -noheader : flash1.trx</​code>​ at CFE prompt.
  
 ==== Bootlogs ==== ==== Bootlogs ====
Line 282: Line 293:
 See [[https://​forum.openwrt.org/​viewtopic.php?​pid=179199|this forum thread]] for more information. See [[https://​forum.openwrt.org/​viewtopic.php?​pid=179199|this forum thread]] for more information.
  
 +
 +===== V2 =====
 +
 +===== Etc. =====
 ==== Tags ==== ==== Tags ====
  
-{{tag>​FastEthernet 5Port InternalAntenna 32RAM 8Flash ​MIPS 74Kc 802.11n Serial}}+{{tag>​FastEthernet 5Port InternalAntenna 32RAM 4Flash bcm47xx bcm47162 ​MIPS 74Kc 802.11n Serial}}
toh/linksys/e1000.1358321742.txt.bz2 · Last modified: 2013/01/16 08:35 by hhm