User Tools

Site Tools


toh:linksys:e1000

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
toh:linksys:e1000 [2014/02/24 09:13]
hhm
toh:linksys:e1000 [2015/03/17 14:09] (current)
zajec [Installation] 14.07 was released, update description
Line 2: Line 2:
  
 ^ Version/​Model ^ CPU ^ RAM ^ Flash ^ Network ^ USB ^ Serial ^ JTAG ^ Bootloader ^ OpenWrt Version Supported ^  ^ Version/​Model ^ CPU ^ RAM ^ Flash ^ Network ^ USB ^ Serial ^ JTAG ^ Bootloader ^ OpenWrt Version Supported ^ 
-| v1   ​| ​ Broadcom ​47162@300MHz ​| 32MB | 4MB | 4x1 | No | Yes | | CFE | Barrier Breaker ​trunk (WIP[[#fine.print|*]]) | +| v1   | Broadcom ​BCM4716B0 (300 MHz) | 32MB | 4MB | 4x1 | No | Yes | Yes | CFE | Barrier Breaker ​14.07 (WiFi untested) | 
-| v2   | +| v2   ​| ​Broadcom BCM5357B0 ​(300 MHz) | 32MB | 4MB | 4x1 | No | Yes | Yes | CFE | Probably 14.07, without LEDs/buttons ​(no failsfe| 
-== Fine print == +| v2.Broadcom BCM5357B0 ​(300 MHz| 32MB | 4MB | 4x1 | No | Yes | Yes | CFE | Barrier Breaker 14.07 (No WiFi) |
-  * At time of writing this (2013/jana firmware image needs to be built from scratch with an option enabled and a patch in order for networking to function properly; see [[https://​forum.openwrt.org/​viewtopic.php?​pid=188754#​p188754|this forum post]] for instructions. +
-  * update (2013/feb) now the wired drivers work out of the box, but enabling wireless currently ​ disables the wired networking until the wireless is disabled once again, so locking oneself out of the wireless can BRICK the device ([[doc:​howto:​generic.failsafe|failsafe]] may work, but I do not know if it is working ​(yeton this device)! +
-  * update (2013/jun) see [[https://​forum.openwrt.org/​viewtopic.php?​pid=201025#​p201025|this]] for more info +
-  * update ​(2013/sepworking, use at your own risk, not enough room on device to install Luci +
-  * update ​(2014/febsee [[https://​forum.openwrt.org/​viewtopic.php?​pid=226138#​p226138|this]] for more info +
- +
  
 ===== V1 ===== ===== V1 =====
Line 16: Line 10:
  
 ==== Installation ==== ==== Installation ====
-The version below does not load LuCi, you can still get a DHCP address and SSH in. +Use the brcm47xx ​''​openwrt-e1000_v1_v2-squashfs.bin'' ​firware image from http://​downloads.openwrt.org/​barrier_breaker/14.07/brcm47xx/mips74k/
- +
-Do this at YOUR OWN RISK, the current snapshot of trunk may be broken! It may be better to wait until the next stable release. +
- +
-Use the brcm47xx ​generic ​.trx firware image, or see if the BIN image works. See details below. +
- +
-The most recent trunk WIP snapshot builds can be found at [[http://​downloads.openwrt.org/​snapshots/trunk/brcm47xx/]] +
- +
-OEM easy installation (aka via original firmware): Not yet (since the wired networking drivers are not included in the stock firmware builds at time of writing this, and wireless is locked by default in the regular builds as far as I know.) +
- +
-  * Update (2013/feb): The firmware can be flashed by updating to DD-WRT first, and then uploading with the DD-WRT firmware update feature (Reason: The stock firmware currently requires [[doc:​techref:​header|a BIN image, not a TRX]].) See [[#​fine.print|fine print]] for notices. +
-  * Update (2013/sep): There is now a BIN formatted image, to be used for OEM easy installation,​ called "​openwrt-e1000_v1_v2-squashfs.bin"​. However, I am not sure if it works (correctly, or at all).+
  
 OEM installation using the TFTP method: Does not work, because of some kind of misconfiguration in the bootloader; use serial-initiated TFTP flashing instead (REQUIRES TTL SERIAL ACCESS). OEM installation using the TFTP method: Does not work, because of some kind of misconfiguration in the bootloader; use serial-initiated TFTP flashing instead (REQUIRES TTL SERIAL ACCESS).
toh/linksys/e1000.1393229590.txt.bz2 · Last modified: 2014/02/24 09:13 by hhm