Differences

This shows you the differences between two versions of the page.

toh:linksys:wrt160n [2012/11/14 06:08]
xyopqqrt The wrt610n does not have usb ports
toh:linksys:wrt160n [2014/05/07 15:56] (current)
danitool
Line 2: Line 2:
===== Supported Versions ===== ===== Supported Versions =====
-^ Model ^ CPU ^ Wireless ^ Flash ^ RAM ^ S/N ^ FCC ID ^ OpenWrt Kamikaze ^ OpenWrt Backfire ^ 
-| WRT160N v1.0 |  BCM4704| BCM4321? | 4MB | 32MB | CSE01? |  |  X | ? | 
-| WRT160N v1.1 |  BCM4703| BCM4321 | 4MB | 16MB | CSE01 | Q87WRT160N |  X (See Below)| ? | 
-| WRT160N v2.0 |  RT2880F| Ralink |  4MB | 16MB | CSE11 | Q87WRT160NV2 |  not supported | ? | 
-| WRT160N v3.0 |  BCM4716| ?  |  4MB | 32MB | CSE41/CSE51 | Q87WRT160NV3 |  WIP (not supported yet) | ? |  
-  * For v1.1: Try an image from [[http://snipes420.googlepages.com/|Here]]. +According to [[wp>Linksys_WRT300N_series#WRT160N]] there is more than one version of this device. Please see what version you have and add information to the wiki or post in this [[http://forum.openwrt.org/viewtopic.php?id=15321|forum thread]]. 
- * For v3.0: Has the same hardware as [[.:E1000|the Linksys E1000]]. + 
- * Please see what version you have and add information to the wiki or post in this [[http://forum.openwrt.org/viewtopic.php?id=15321|forum thread]]. +^ Model ^ CPU ^ Wireless ^ Flash ^ RAM ^ S/N ^ FCC ID ^ OpenWrt Kamikaze ^ OpenWrt Backfire ^ OpenWrt trunk (Barrier Breaker) ^ 
-  * According to [[wp>Linksys_WRT300N_series#WRT160N]] there is more than one version of this device. +| WRT160N v1.0 |  BCM4704| BCM4321? | 4MB | 32MB | CSE01? |  |  X | ? | ? | 
 +| WRT160N v1.1 |  BCM4703| BCM4321 | 4MB | 16MB | CSE01 | Q87WRT160N |  X (See Below)| ? | ? | 
 +| WRT160N v2.0 |  RT2880F| Ralink |  4MB | 16MB | CSE11 | Q87WRT160NV2 |  not supported | ? | ? | 
 +| WRT160N v3.0 |  BCM4716| ?  |  4MB | 32MB | CSE41/CSE51 | Q87WRT160NV3 |  WIP (not supported yet, see below) | ? | WIP | 
 + 
 +==== V1.1 ==== 
 + 
 +For v1.1, try an image from [[http://snipes420.googlepages.com/|Here]]. 
 + 
 +==== V3.0 ==== 
 + 
 +V3.0 has the same hardware as [[.:E1000|the Linksys E1000 v1]]; see the information for it, which may be helpful
 + 
 +As of 2013-08-27, trunk snapshots support the WRT160Nv3: http://downloads.openwrt.org/snapshots/trunk/brcm47xx/openwrt-wrt160n_v3-squashfs.bin 
 + 
 +Please see also the following forum topics: 
 +  * https://forum.openwrt.org/viewtopic.php?id=44045 
 +  * https://forum.openwrt.org/viewtopic.php?id=39581 
===== Installation ===== ===== Installation =====
Line 30: Line 43:
</code> </code>
-  - go to 'Memory Technology Devices (MTD) --->' +  - enable "Support 8-bit buswidth"<code>  Location: 
-   - then 'RAM/ROM/Flash chip drivers --->' +    -> Device Drivers  
-     - and enable &quot;Support  8-bit buswidth&quot;+      -> Memory Technology Device (MTD) support (MTD [=y]) 
 +         -> RAM/ROM/Flash chip drivers 
 +          -> Flash chip driver advanced configuration options (MTD_CFI_ADV_OPTIONS [=y]) 
 +             -&gt; Specific CFI Flash geometry selection 
 +                [*]    Support  8-bit buswidth&lt;/code>;
  - Exit the configuration menu and save the settings.   - Exit the configuration menu and save the settings.
  - build the whole thing again with the new config. (This time wont take as long)   - build the whole thing again with the new config. (This time wont take as long)
Line 45: Line 62:
| **Vendor:** | Broadcom  | Ralink | Broadcom | | **Vendor:** | Broadcom  | Ralink | Broadcom |
| **Bootloader:** | CFE | [[doc:techref:bootloader:uboot]] | CFE | | **Bootloader:** | CFE | [[doc:techref:bootloader:uboot]] | CFE |
-| **System-On-Chip:** | Broadcom 4703KFBG  | RT2880F  (MIPS xyK V?.?) | Broadcom 4716B0KFBG (MIPS xyK V?.?) | +| **System-On-Chip:** | Broadcom 4703KFBG  | RT2880F  (MIPS 4KEc V?.?) | Broadcom 4716B0KFBG (MIPS 74Kc V?.?) |
| **CPU/Speed** | BCM4703 266 MHz | 266 MHz | BCM4716 300 MHz | | **CPU/Speed** | BCM4703 266 MHz | 266 MHz | BCM4716 300 MHz |
| **Flash-Chip:** | [[http://www.eonsdi.com/pdf/EN29LV320.pdf|EN29LV320AB]] | ??  | ?? | | **Flash-Chip:** | [[http://www.eonsdi.com/pdf/EN29LV320.pdf|EN29LV320AB]] | ??  | ?? |
Line 86: Line 103:
==== V2.0 ==== ==== V2.0 ====
-J10 is an empty 5-pin header, and is likely a serial port (console)+J10 is a serial port and it works if you use a 3.3v TTL to RS-232.
J11 is an empty 14-pin header and is likely a JTAG port to the CPU. J11 is an empty 14-pin header and is likely a JTAG port to the CPU.
Line 92: Line 109:
**J10** **J10**
-^ Pin 1 ^ ? ^ Pin 2 ^ ? ^ Pin 3 ^ ? ^ Pin 4 ^ ? ^ Pin 5 ^ ? | +| Near WAN port ^ Pin 1 ^ 3.3v ^ Pin 2 ^ TX ^ Pin 3 ^ RX ^ Pin 4 ^ NC ^ Pin 5 ^ GND |
**J11** **J11**
Line 105: Line 122:
=== Serial === === Serial ===
->[doc:hardware:port.serial]] ->[doc:hardware:port.serial]]
-JP2 is a 3.3v serial port.  Boot messages can be seen if you connect a 3.3v level shifter here and monitor with a serial port.+JP2/J10 is a 3.3v serial port.  Boot messages can be seen if you connect a 3.3v level shifter here and monitor with a serial port.
DO NOT CONNECT DIRECTLY TO A PC SERIAL PORT. Use a 3.3v TTL level shifter. DO NOT CONNECT DIRECTLY TO A PC SERIAL PORT. Use a 3.3v TTL level shifter.
Line 123: Line 140:
===== Recovery ===== ===== Recovery =====
-===== V1.1 =====+==== V1.1 ====
If the device becomes bricked, (and this can happen very easily with this device) you should attach a serial port to it to view the console and see why it has stopped booting. If the device becomes bricked, (and this can happen very easily with this device) you should attach a serial port to it to view the console and see why it has stopped booting.
  * Boot_wait does not seem to work on this device.   * Boot_wait does not seem to work on this device.
Line 134: Line 151:
</code> </code>
-===== V3.0 =====+==== V3.0 ====
To recover it, do the following procedure: To recover it, do the following procedure:
  * Turned on, press the Reset button for 30 seconds   * Turned on, press the Reset button for 30 seconds

Back to top

toh/linksys/wrt160n.1352869709.txt.bz2 · Last modified: 2012/11/14 06:08 by xyopqqrt