Differences

This shows you the differences between two versions of the page.

toh:linksys:wrt160nl [2013/01/25 16:13]
gameboyrmh Added commands I used successfully for migrating from DD-WRT to OpenWRT.
toh:linksys:wrt160nl [2014/04/25 04:36] (current)
benm
Line 1: Line 1:
====== Linksys by Cisco WRT160NL ====== ====== Linksys by Cisco WRT160NL ======
-Atheros AP81 reference design with USB & 802.11 b/g/n WiFi.+Atheros AP81 reference [[http://moverslos-angeles.net/]] with USB & 802.11 b/g/n WiFi.
===== Supported versions ===== ===== Supported versions =====
Line 21: Line 21:
==== Using ready build ==== ==== Using ready build ====
 +Supported since 10.03.1
 +
You can download [[http://downloads.openwrt.org/backfire/10.03.1/ar71xx/|10.03.1]] build called openwrt-ar71xx-wrt160nl-squashfs-factory.bin. You can download [[http://downloads.openwrt.org/backfire/10.03.1/ar71xx/|10.03.1]] build called openwrt-ar71xx-wrt160nl-squashfs-factory.bin.
After using it you will have to install **kmod-ath9k** to [[doc:uci/wireless|get WiFi working]]... After using it you will have to install **kmod-ath9k** to [[doc:uci/wireless|get WiFi working]]...
Line 122: Line 124:
</code> </code>
-==== Migrate from DD-WRT to OpenWRT ====+===== Migrate from DD-WRT to OpenWrt =====
<code> <code>
Line 247: Line 249:
| 21| BTN_RESET | | 21| BTN_RESET |
 +As reported here
 +
 +http://barbara320.gotdns.com/alnis/computers/openwrt/17%20GPIO%20LEDs%20output%20and%20input%20for%20motion%20detector.txt
 +
 +and here (in Polish)
 +
 +http://openrouter.info/forum/viewtopic.php?f=19&t=554
 +
 +there are two easily accessible spare gpios. Gpio13 is the extra pin on the serial header, and gpio0 is at the bottom left of the board, where there are pads for a fourth LED which has not been soldered in.
 +The author of the first link above reported that gpio13 would only work as an output, not as an input. I did not have that problem.
===== Specific configuration ===== ===== Specific configuration =====
Line 267: Line 279:
|4        | 0 | |4        | 0 |
-Port 4 is the internal/cpu port. Port 5 is probably unconnected.+Port 4 is the internal/cpu port. Port 5 (tagged 'CPU' in LUCI) is probably unconnected
 + 
 +Note that, at least for 12.09, switch support seems to have issues: switch configuration changes don't "take" until a reboot, and when configuring tagged and untagged VLANs, outgoing traffic for the untagged VLAN is still tagged. This needs to be further investigated. 
 + 
 +If you don't need the switch, consider swapping the WAN and LAN ports as eth1 is directly connected.
==== Failsafe mode ==== ==== Failsafe mode ====
Line 317: Line 333:
===== Antenna ===== ===== Antenna =====
-The supplied short dipole antennas can be easily replaced with large omni or directional antenna.+The [[supplied]http://moverslos-angeles.net/] short dipole antennas can be easily replaced with large omni or directional antenna.
====== Other info ====== ====== Other info ======
Original exploration thread https://forum.openwrt.org/viewtopic.php?id=20298&p=1 Original exploration thread https://forum.openwrt.org/viewtopic.php?id=20298&p=1

Back to top

toh/linksys/wrt160nl.1359126828.txt.bz2 · Last modified: 2013/01/25 16:13 by gameboyrmh