User Tools

Site Tools


toh:mikrotik:mikrotik_rb750p-pbr2_powerbox

MikroTik RB750P-PBr2 (PowerBox)

Supported Versions

FIXME Please add a link where to download the external firmware image. — tmomas 2017/10/04 23:21

Hardware Highlights

Installation

Enable TFTP

OEM easy installation

Method 1 (using Winbox)

Download Winbox from Mikrotik webpage https://download2.mikrotik.com/routeros/winbox/3.11/winbox.exe

Boot up the RB750P r2, connect your DHCP client to any of the ports 2 to 5 but not the Internet labeled port (Port 1)

Open up Winbox, IP Address 192.168.88.1, If a password has been set put this in if not the Default is just Blank

Also, while we are in Winbox lets backup the license so returning to RouterOS is later possible. Go to:

  System → Routerboard → Settings → License → Export key

Go to:

  System → Routerboard → Settings → Boot device: Try ethernet once then NAND
  System → Routerboard → Settings → Boot protocol: DHCP
  System → Routerboard → Settings → Force Backup Booter: Checked (if supported by your routerboard - !IMPORTANT)
  System → Shutdown

Connect the LAN port on Internet labled port and reboot the RB750P r2, Connect the computers LAN port on Internet

Method 2 (TFTP with Telnet)

Please note that the aforementioned mechanism is not properly working on some boards. Don't worry, boot up the mikrotik board, connect your DHCP client to port 1. An address from 192.168.88.0/24 must be obtained. You can now telnet to the board, and configure it for TFTPboot.

Telnet user is admin, leave the password empty.

telnet 192.168.88.1
system routerboard settings set boot-device=try-ethernet-once-then-nand 
system routerboard settings set boot-protocol=dhcp 

Now reboot the board, it should boot from the labled "Internet" port now.

Install Firmware

For Windows 10 x64 (7/XP/Vista should be ok)

Download http://tftpd32.jounin.net/tftpd32_download.html (i used tftpd64 portable edition) and the mikrotik-rb-nor-flash-16M-initramfs-kernel.bin and mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin from Downloads above and then save them in the same tftpd32 folder IMPORTANT

Extract the tftpd32 folder and make sure ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin is there and open up tftp32 config file and match theses settings I have (worked for me)

[DHCP]

 4C:5E:0C:XX:XX:XX=192.168.1.250  (Should be the same ETH1 MAC Address)
 BootFile=lede-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin
 Lease_NumLeases=2
 IP_Pool=192.168.1.2
 PoolSize=4
 Mask=255.255.255.0
 Gateway=192.168.1.1
 Lease (minutes)=90

Save!

Open up tftpd64.exe and the go to Settings > GLOBAL and make sure, TFTP server and DHCP are ticked, everything else unticked, Save and Exit and then reopen tftpd64.exe for the saved changes!

Set a static IP on your Windows computer LAN port with the following

 192.168.1.2  (Keep this to 192.168.1.2 or tftpd wont work **IMPORTANT**)
 255.255.255.0 (**IMPORTANT**)
 192.168.1.1 (**IMPORTANT**)

Follow method 1 to enable TFTP, Once done keep the LAN on port 1 (internet port) and then you should see something transferring and then the RB750r2 will boot into LEDE, Unplug the LAN port from Internet port 1 and set a DHCP on your Windows machine and then plug in the LAN port into any port 2-5 and the Internet port for a Cable Modem? Switch? Router? something that has internet access to it if you want to keep the LEDE on as this is in RAM mode and won't save any changes!

Now, If you want to erase you RouterOS then follow theses steps;

Log into SSH 192.168.1.1 with just root and password been blank (press enter)

cd /tmp
wget http://downloads.lede-project.org/snapshots/targets/ar71xx/mikrotik/lede-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin
mtd write -r lede-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin firmware

The device will reboot after flashing and will boot LEDE.

Upgrade

  1. Go to System > Backup/Flash Firmware
  2. Untick Keep settings
  3. Click the Browse button and select the upgrade lede-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin image
  4. Click the Flash Image button

Or use sysupgrade over SSH

Debricking

Load initframs like using TFTP like in step 1.

Failsafe mode

Only built in LEDE failsafe

Returning to RouterOS

  1. Install the "rbcfg" package on in LEDE.
  2. By terminal:
  • root@LEDE:~#rbcfg set boot_protocol bootp
  • root@LEDE:~#rbcfg set boot_device ethnand
  • root@LEDE:~#rbcfg apply
  1. Open Netinstall and reboot routerboard. Now netinstall sees routerboard and you can install RouterOS.

If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again

In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall

Switch Ports (for VLANs)

Ports 2-5 directly correspond to ports 2-5 as labeled on the unit, port 1 is the Internet (WAN) on the unit, 0 is the internal connection to the CPU.

Port Switch port
CPU 0
Internet (WAN) 1
LAN 1 2
LAN 2 3
LAN 3 4
LAN 4 5

Buttons

The MikroTik RB750P-PBr2 (PowerBox) has the following buttons:

BUTTON Event
Reset reset

Hardware

Info

Nothing.

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Opening the case

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …

  • To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for MikroTik RB750P-PBr2 (PowerBox) @@Version@@
EXAMPLE 115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Notes

  • the bootloader is not initializing the serial PINs so the serial console wont work (until bootloader reflash)
  • LEDE enables serial output from point of kernel loading

Tags

FIXME Add tags below, then remove this fixme.

How to add tags

toh/mikrotik/mikrotik_rb750p-pbr2_powerbox.txt · Last modified: 2017/10/11 15:59 by robimarko