This device is currently completely unsupported in OpenWrt

The Netgear DGN220 v2 is an BCM63281-based ADSL router with 802.11g/n wireless and ADSL2+ support. It has a 4-port switch, and two built-in wireless antennas.

The (originally unpopulated) 6-pin header J401 is a serial port on 3.3V level operating at 115200 8n1.

Note: MAC addresses have been substituted by: XX:XX:XX:XX:XX:XX!

HELO CPUI L1CI DRAM ---- PHYS ZQDN PHYE DINT LSYN USYN MSYN LMBE PASS ---- ZBSS CODE DATA L12F MAIN NAN0 BT00 NAN9 ERR0 NAN9 NAN3 RFS1 NAN5 CFE version 2.0.3 for DGN2200v2 (32bit,SP,BE) Build Date: Wed Dec 1 17:29:52 CST 2010 (silver@dev3) Copyright (C) 2000-2009 Broadcom Corporation. NAND flash device: name , id 0x2075 block 16KB size 32768KB Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Main Thread: TP0 Memory Test Passed Total Memory: 33554432 bytes (32MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-3) : 963281TAN Number of MAC Addresses (1-32) : 10 Base MAC Address : xx:xx:xx:xx:xx:xx PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 111 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 111 CFE> web info: Waiting for connection on socket 0. CFE> CFE> CFE> help Available commands: tftpd Start TFTP server checkmem Check memory. fr read data from flash. nmrp start memory or registers. sm Set memory or registers. dm Dump memory or registers. chw Write chkw image start from beginning of the flash w Write the whole image start from beginning of the flash e Erase NAND flash r Run program from flash image or from host depend on [f/h] flag p Print boot line and board parameter info c Change booline parameters i Erase persistent storage data a Change board AFE ID b Change board parameters reset Reset the board bid write board id to nand flash. flashimage Flashes a compressed image after the bootloader. ping Ping a remote IP host. arp Display or modify the ARP Table ifconfig Configure the Ethernet interface help Obtain help for CFE commands For more information about a command, enter 'help command-name' *** command status = 0

Note: MAC addresses have been substituted by: XX:XX:XX:XX:XX:XX!

Booting from only image (0xb8004000) ... Decompression OK! Entry at 0x80014230 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80014230 Linux version 2.6.30 (bobguo@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Fri Jan 21 09:06:59 CST 2011 BCM Flash API. Flash device is not found. 963281TAN prom init CPU revision is: 0002a075 (Broadcom4350) Determined physical RAM map: memory: 01f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00001f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00001f00 On node 0 totalpages: 7936 free_area_init_node: node 0, pgdat 8035d2d0, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 30 pages used for memmap Normal zone: 3810 pages, LIFO batch:0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7874 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes RCU-based detection of stalled CPUs is enabled. NR_IRQS:128 PID hash table entries: 128 (order: 7, 512 bytes) console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 27656k/31744k available (2691k kernel code, 4088k reserved, 694k data, 124k init, 0k highmem) Calibrating delay loop... 319.48 BogoMIPS (lpj=159744) Mount-cache hash table entries: 512 net_namespace: 768 bytes NET: Registered protocol family 16 Total Flash size: 0K with -1 sectors registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:02:00.0: supports D1 D2 pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 54 io scheduler noop registered (default) pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 Failed to read image tag from flash Broadcom DSL NAND controller (BrcmNand Controller) i=0, CS[0] = 0 brcmnand_probe: CS0: dev_id=20752075 NAND Config: Reg=03032200, chipSize=32 MB, blockSize=16K, erase_shift=e busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff timing1 not adjusted: 5363444f timing2 not adjusted: 00000fc6 BrcmNAND mfg 20 75 ST ST_NAND256W3A 32MB Found NAND: ACC=f3000000, cfg=03032200, flashId=20752075, tim1=5363444f, tim2=00000fc6 BrcmNAND version = 0x0202 32MB @(null) brcmnand_probe: CS0: dev_id=20752075 1. Found NAND chip on Chip Select 0, chipSize=32MB, usable size=32MB, base=0x00000000 brcmnand_scan: B4 nand_select = 40000002 brcmnand_scan: After nand_select = 40000002 page_shift=9, bbt_erase_shift=14, chip_shift=25, phys_erase_shift=14 Brcm NAND controller version = 2.2 NAND flash size 32MB @00000000 brcmnand_scan: mtd->oobsize=16 brcmnand_scan: oobavail=12, eccsize=512, writesize=512 brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3 brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table found at page 65504, version 0xFF Bad block table found at page 65472, version 0xFF numchips=1, size=2000000 Creating 4 MTD partitions on "bcm63xx-nand.0": 0x000000004000-0x000000f00000 : "rootfs" 0x000000f00000-0x000001dfc000 : "rootfs_update" 0x000001e00000-0x000001f00000 : "data" 0x000000000000-0x000000004000 : "nvram" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Jan 21 2011 09:05:12 Broadcom Logger v0.1 Jan 21 2011 09:04:51 BCM63XX_USB USB Device not present Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00c2c000: 0x14a5 instead VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 124k freed init started: BusyBox v1.00 (2011.01.21-01:15+0000) multi-call binary jffs2_scan_inode_node(): CRC failed on node at 0x000209dc: Read 0xffffffff, calculated 0x1afe7415 Empty flash at 0x00020a50 ends at 0x00020c00 BusyBox v1.00 (2011.01.21-01:15+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... bcmxtmcfg: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint bcmxtmcfg: bcmxtmcfg_init entry JFFS2 notice: (175) check_node_data: wrong data CRC in data node at 0x0007ebb8: read 0x6f11f0d, calculated 0x2697fdb7. adsl: adsl_init entry Broadcom BCMPROCFS v1.0 initialized Broadcom BCM6328B0 Ethernet Network Device v0.1 Jan 21 2011 09:04:58 ETH Init: 90 tx BDs at 0xa19cc000 ETH Init: 200 rx BDs at 0xa1aee800 ETH Init: 200 rx BDs at 0xa1aee000 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth0: MAC Address: xx:xx:xx:xx:xx:xx eth1: MAC Address: xx:xx:xx:xx:xx:xx eth2: MAC Address: xx:xx:xx:xx:xx:xx eth3: MAC Address: xx:xx:xx:xx:xx:xx PCI: Enabling device 0000:02:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:02:00.0 to 64 wl:srom strapped wl:(srom strapped) probe/present=0 wl:srom not detected,using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43225_map.bin wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.11.cpe4.06L03.8 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered p8021ag: p8021ag_init entry Broadcom 802.1Q VLAN Interface, v0.1 : not found jffs2_scan_inode_node(): CRC failed on node at 0x000209dc: Read 0xffffffff, calculated 0x1afe7415 Empty flash at 0x00020a50 ends at 0x00020c00 start parsing board_data !! start parsing nvram JFFS2 notice: (254) check_node_data: wrong data CRC in data node at 0x0007ebb8: read 0x6f11f0d, calculated 0x2697fdb7. /proc/sys/net/ipv4/neigh/br0/base_reachable_time: cannot create Reading board data... WSC UUID: 0xaf0795cf1cbb8861319592e843fd2c5a device eth0 entered promiscuous mode device eth1 entered promiscuous mode device eth2 entered promiscuous mode device eth3 entered promiscuous mode arping: not found mkdir: Cannot create directory `wl0': Read-only file system /var/lan/eth0: cannot create DSL mode command is xdslctl start --bitswap on --sra off --lpair i --mod dlt2pe --up BcmAdsl_Initialize=0xC00E6110, g_pFnNotifyCallback=0xC0117D14 pSdramPHY=0xA1FFFFF8, 0x2E1C2E9C 0x2E0C2A9C AdslCoreSharedMemInit: shareMemAvailable=491424 AdslCoreHwReset: AdslOemDataAddr = 0xA1F69564 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered XTM Init: 400 rx BDs at 0xa0d0d000 XTM Init: 100 rx BDs at 0xa1546400 bcmxtmrt: MAC address: 4c 60 de 4e a4 da [DoCreateDeviceReq.2619]: register_netdev [DoCreateDeviceReq.2621]: register_netdev done Setting SSID: "Bezeq-n_A4D8" Setting SSID: "NETGEAR-2" wl0.1 (): not using net_device_ops yet Setting SSID: "NEwl0.2 (): not using net_device_ops yet TGEAR-3" Setting SSID: "NETGEAR-4" wl0.3 (): not using net_device_ops yet Info: No FWPT default policies. Chanspec set to 0x2b06 httpd: socket bound in 0.0.0.0:80. WinkDbg: agApi_seWinkDbg: agDoIoctl(1919): port[8], port_num[443], enable[0] tDeviceListenPort(4263): port_idx[8], port_num[443], enable[0] WinkDbg: agApi_setDeviceListenPort(4279): ret_val = [0] WinkDbg: agApi_seWinkDbg: agDoIoctl(1919): port[9], port_num[21], enable[0] tDeviceListenPort(4263): port_idx[9], port_num[21], enable[0] WinkDbg: agApi_seWinkDbg: agDoIoctl(1919): port[10], port_num[30001], enable[0] tDeviceListenPort(4279): ret_val = [0] WinkDbg: agApi_setDeviceListenPort(4263): port_idx[10], port_num[30001], enable[0] WinkDbg: agApi_setDeviceListenPort(4279): ret_val = [0] info, udhcp server (v0.9.8) started error, unable to parse 'option wins ' error, unable to parse 'option domain ' info, udhcp server (v0.9.8) started info, udhcp server (v0.9.8) started info, udhcp server (v0.9.8) started killall: zebra: no process killed killall: ripd: no process killed WinkDbg: agApi_seWinkDbg: agDoIoctl(1919): port[0], port_num[520], enable[1] tDeviceListenPortWinkDbg: agDoIoctl(1975): 002 port[0], port_num[520] (4263): port_idxWinkDbg: agDoIoctl(1979): 002 Wins_01[0], Wins_02[0], Wins_03[0] [0], port_num[520], enable[1] WinkDbg: agApi_setDeviceListenPort(4279): ret_val = [0] zebra: No such file or directory ripd: No such file or directory POT integrity check OK. /usr/sbin/acl_logd: not found a.b.c.d a00008a Warning - changing ownership '//var/spool' to 0/0 Warning - changing ownership '//var/spool' to 0/0 Warning - changing ownership '//var/spool/lpd' to 0/0 Warning - changing ownership '//var/spool/lpd' to 0/0 Warning - changing ownership '//var/spool/lpd/printer' to 0/0 Warning - changing ownership '//var/spool/lpd/printer' to 0/0 Warning - printer: cannot open lp device '/dev/printer0' - No such device device wl0 entered promiscuous mode br0: port 5(wl0) entering learning state Reaped 722 # br0: port 5(wl0) entering forwarding state Start WPS !! UPnP daemon is ready to run gpio_drv_ioctl: usb_led_state = 0x0 killall: cwmpCPE: no process killed read_from_wps() failure set_wps_env: SET wps_method=1 wps_action=2 wps_config_command=1 wps_pbc_method=2 wps_ifname=wl0 ftpRestart: killall: bftpd: no process killed http_d: got signal killall: bftpd: no process killed WinkDbg: agApi_seWinkDbg: agDoIoctl(1919): port[9], port_num[21], enable[0] tDeviceListenPortWinkDbg: agDoIoctl(1919): port[10], port_num[30001], enable[0] (4263): port_idx[9], port_num[21], enable[0] WinkDbg: agApi_setDeviceListenPort(4279): ret_val = [0] WinkDbg: agApi_setDeviceListenPort(4263): port_idx[10], port_num[30001], enable[0] WinkDbg: agApi_setDeviceListenPort(4279): ret_val = [0]

For some Help with the Tags, please have a look here: tags