Boot of original Netgear DGN3500 firmware

Copy from Serail Flash to RAM... done
## Starting application at 0x80200000 ...
setenv kernel_addr=0x50000
setenv kernel_addr=0x50000

PID=YP5726

Will check KFS integrality. read KFS first
EEPROM @0x0 read: addr 0x80500000  off 0x50000  count 16384000
..........................................................................................................................................................................................................................................................done
sercomm_trap: done
check_checksum start

image=27, image+1=5, image+2=19

image-2=4D, image-1=6D, image=34

PID_Offset=0x85C000, checksum_in_file=0x4A84, checksum_calculat=0x4A84, checksum_data_string=4A84
## Application terminated, rc = 0x0
## Booting image at 00050000 ...
*** eeprom_read
*** eeprom_read

addr = 50000
CFG_LOAD_ADDR = 80100000
..................addr = 80500000

   Image Name:   MIPS Linux-2.6.20
   Created:      2011-02-24   8:48:05 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1225873 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  8039d000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

 **** do_bootm_linux
   commandline=root=/dev/mtdblock0 ip=192.168.1.1:192.168.1.15::::eth0:on console=ttyS1,115200 ethaddr=aa:bb:cc:dd:ee:ff phym=64M mem=64M panic=1
   argc=2
   argv[0]=bootm
   argv[1]=0x50000

Starting kernel ...

Infineon Amazon_S
mips_hpt_frequency:166666666, counter_resolution = :
Linux version 2.6.20-Amazon_S (root@build-server) (gcc version 3.4.4 20050119 (MIPS SDE)) #73 Thu Feb 24 16:47:59 CST 2011
phym = 04000000, memsz = 04000000, max_pfn = 00004000
CPU revision is: 0001954c
Determined physical RAM map:
User-defined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
  DMA zone: 128 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 16256 pages, LIFO batch:3
  Normal zone: 0 pages used for memmap
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/mtdblock0 ip=192.168.1.1:192.168.1.15::::eth0:on console=ttyS1,115200 ethaddr=aa:bb:cc:dd:ee:ff phym=64M mem=64M panic=1 
1 MIPSR2 register sets available
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
Setting up vectored interrupts
vec_vi[0]:0x803de200: 0x8000eb88
vec_vi[1]:0x803de400: 0x8000eb88
vec_vi[2]:0x803de600: 0x80003df4
vec_vi[3]:0x803de800: 0x80003ea4
vec_vi[4]:0x803dea00: 0x80003f38
vec_vi[5]:0x803dec00: 0x80003fd8
vec_vi[6]:0x803dee00: 0x8000406c
vec_vi[7]:0x803df000: 0x80004100
PID hash table entries: 256 (order: 8, 1024 bytes)
Using 166.667 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60908k/65536k available (2576k kernel code, 4564k reserved, 1112k data, 136k init, 0k highmem)
Calibrating delay loop... 222.00 BogoMIPS (lpj=1110016)
Mount-cache hash table entries: 512
cpu_wait is r4k_wait
NET: Registered protocol family 16
PCI: Probing PCI hardware on host bus 0.
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Infineon Technologies PCI driver version 1.0.0 
Infineon Technologies PCI driver version 1.0.0 
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
Infineon Technologies DMA driver version 1.0.0 
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
dev 0000:00:00.0: interrupt pin 1
dev 0000:00:0e.0: interrupt pin 1
Infineon Technologies GPTU driver version 1.0.0 
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
Infineon Technologies port driver version 1.0.2 
Infineon Technologies CGU driver version 1.0.0 
cgu: misc_register on minor = 62
Infineon Technologies PMU driver version 0.0.1 
Infineon Technologies WDT driver version 1.0.0 
IFX MEI Version 4.00.01

Lantiq CPE API Driver version: DSL CPE API V4.8.0

Predefined debug level: 3
ttyS0 at MMIO 0xbe100400 (irq = 98) is a IFX_ASC
ttyS1 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC
Infineon Technologies ASC driver version 1.0.0 
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 3 devices...
IMQ driver loaded successfully.
	Hooking IMQ after NAT on PREROUTING.
	Hooking IMQ after NAT on POSTROUTING.
IFX SWAPI v1 - IFX Common Ethernet Switch API, version 1.0.1.1
(c) Copyright 2008, Infineon Technologies AG
Switch Driver Version: 1.0.4
 External Switch ID :0x0000ffff


*** init rtl8366rb **
The 0x02=0x1C   (==0x1C ?)
***The 0x0=0x830    0
Logical CPU port is disabled
amazon_s_switch_set_headerstatus_pmactodma[528]: Enable PMAC to DMA
amazon_s_switch_set_headerstatus_dmatopmac[558]: Enable DMA to PMAC
SWAPI: Registered character device [ar9] with major no [244] and minor no [1]Successfully registered dev [AR9] with Genric Kernel APIinit_amazon_s_mtd: chip probing count 0
CFI: Found no Amazon_S Bank 0 device at location zero
Amazon_S: No support flash chips found!
Infineon Technologies Synchronous Serial Controller (SSC) driver version 1.1.2
amazon_s_sscAllocConnection: device amazon_s-sflash register sucessfully!
MTD driver for SPI flash.
Probing for Serial flash ...
Creating 10 MTD partitions on "amazon_s-sflash":
0x001a0000-0x00f50000 : "File-System"
0x00050000-0x00f50000 : "KFS"
0x00000000-0x00010000 : "U-Boot"
0x00030000-0x00040000 : "NVRAM"
0x00000000-0x00010000 : "U-Boot"
0x00020000-0x00030000 : "DPF"
0x00010000-0x00020000 : "BOOTENV"
0x00ff0000-0x01000000 : "POT"
0x00fd0000-0x00ff0000 : "TM"
0x00f50000-0x00fd0000 : "UILANG"
Infineon Technologies Synchronous SPI flash driver version 1.0.2 
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
Infineon Technologies LED driver version 1.0.0 
Infineon Technologies DEU driver version 1.0.0 
PAGE_SIZE = 4096
IFX DEU DES initialized (multiblock) (DMA).
IFX DEU AES initialized (multiblock) (DMA).
IFX DEU ARC4 initialized (multiblock) (DMA).
IFX DEU SHA1 initialized (DMA).
IFX DEU MD5 initialized (DMA).
IFX DEU SHA1_HMAC initialized (DMA).
IFX DEU MD5_HMAC initialized (DMA).
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
nf_ct_ftp: registering helper for pf: 2 port: 21
nf_ct_ftp: registering helper for pf: 10 port: 21
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
atmpvc_init() failed with -17
VFS: Mounted root (squashfs filesystem) readonly.
Time: MIPS clocksource has been installed.
Freeing unused kernel memory: 136k freed
init started:  BusyBox v1.00 (2011.02.24-08:49+0000) multi-call binary
init started:  BusyBox v1.00 (2011.02.24-08:49+0000) multi-call binary
Starting pid 137, console /dev/console: '/usr/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
mount: Mounting devpts on /dev/pts failed: No such file or directory
mknod: /dev/sc_led: File exists
led_pb_api: module license 'Sercomm' taints kernel.
led_init_module : set GPIO 3, 19 to output
insmod: cannot open module `/lib/modules/ipt_string.ko': No such file or directory
netfilter PSD loaded - (c) astaro AG
ipt_random match loaded
dwc_otg: version 2.40a 10-APR-2006 (ker:20614)
dwc_otg dwc_otg: base=0xbe101000
dwc_otg dwc_otg: dwc_otg_device=0x83fe2e80
DWC_otg: Using DMA mode
dwc_otg dwc_otg: DWC OTG Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
dwc_otg dwc_otg: new USB bus registered, assigned bus number 1
dwc_otg dwc_otg: irq 54, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
Enable USB0 power!!
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 2.6.20-Amazon_S dwc_otg_hcd
usb usb1: SerialNumber: dwc_otg
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
fuse init (API version 7.8)
klips_info:ipsec_init: KLIPS startup, Openswan KLIPS IPsec stack version: 2.4.6rc3
NET: Registered protocol family 15
klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=251)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0
KLIPS cryptoapi interface: alg_type=15 alg_id=12 name=cbc(aes) keyminbits=128 keymaxbits=256, found(0)
KLIPS: lookup for ciphername=cbc(twofish): not found 
KLIPS: lookup for ciphername=cbc(serpent): not found 
KLIPS: lookup for ciphername=cbc(cast5): not found 
KLIPS: lookup for ciphername=cbc(blowfish): not found 
KLIPS cryptoapi interface: alg_type=15 alg_id=3 name=cbc(des3_ede) keyminbits=192 keymaxbits=192, found(0)
KLIPS cryptoapi interface: alg_type=15 alg_id=2 name=cbc(des) keyminbits=64 keymaxbits=64, found(0)
device eth0 entered promiscuous mode
Infineon Technologies PPE driver version 1.0.0 
Logical CPU port is disabled
amazon_s_switch_set_headerstatus_pmactodma[528]: Enable PMAC to DMA
amazon_s_switch_set_headerstatus_dmatopmac[558]: Enable DMA to PMAC
Logical CPU port is enabled
Logical CPU port is disabled
amazon_s_switch_set_headerstatus_dmatopmac[558]: Enable DMA to PMAC
ppe: ATM init succeeded (drv 0.0.1, fw 5.1.0.2.1.0)
killall: dsl_cpe_control: no process killed
Modem is not ready!
[IFX_MEI_Ioctls 2680]: DSL_FIO_BSP_GET_CHIP_INFO: version 1
userspace registering PID
[IFX_MEI_DFEMemoryAlloc 1583]: image_size = 346368
[DSL_BSP_FWDownload 1752] -> IFX_MEI_BarUpdate()
wsc_det: pin=20172688
[IFX_MEI_RunAdslModem 1422] -> IFX_MEI_BarUpdate()
[IFX_MEI_IrqHandle 1936]: Got MODEM_READY_MSG
[IFX_MEI_IrqHandle 1936]: Got MODEM_READY_MSG
[IFX_MEI_RunAdslModem 1468]: Modem is ready.
ap_name=(null) action=start
vconfig: open /proc/net/vlan/config: No such file or directory
vconfig: open /proc/net/vlan/config: No such file or directory
vconfig: open /proc/net/vlan/config: No such file or directory
vconfig: open /proc/net/vlan/config: No such file or directory
device eth0 is already a member of a bridge; can't enslave it to bridge br0.
br0: port 1(eth0) entering learning state
/bin/echo GMT+8 > /etc/TZ
ap_name=firewall action=restart
 Uplink bandwidth enable
<rc> fw_qos_init: rate up=512, down=0

fw_pt 
===========================  fw_qos  =========================================
rules=,length=0
********************** end of qos_parse_port for apps
rules=,length=0
********************** end of qos_parse_port for game
********************** end of qos_parse_mac 
sh: cannot create /proc/sc_lan_prio: Directory nonexistent
/bin/echo "0000" > /proc/sc_lan_prio 
********************** end of qos_parse_LANport 
===========================  fw_qos end =====================================
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
/bin/echo GMT+8 > /etc/TZ
0:0
sh: cannot create /proc/net/ipt_condition/schedule: Directory nonexistent
parse_conf Error!!
Error Number=-2
PROJECT=DGN3500_NA_16M
killall: udhcpd: no process killed
killall: miniupnpd: no process killed
killall: dnrd: no process killed
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
dnrd -a 192.168.0.1 -m hosts -c off --timeout=0 -b 
rc: /bin/echo export ATH_countrycode=840 >> /etc/ath/sc_cfg <
rc: /bin/echo export WIFI0_MAC=AA:BB:CC:DD:EE:FF >> /etc/ath/sc_cfg <
#######################wlan_up######################
rc: /bin/echo export AP_PRIMARY_CH=11 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SECONDARY_CH=-1 >> /etc/ath/sc_cfg <
rc: /bin/echo export FORCE_11NG_HT40=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID=\"NETGEAR\" >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID_HIDE=0 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_ISO=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SECMODE=NONE >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SECMODE=WSC >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID_2=\"NETGEAR2\" >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID_HIDE_2=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_ISO_2=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SECMODE_2=NONE >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID_3=\"NETGEAR3\" >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID_HIDE_3=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_ISO_3=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SECMODE_3=NONE >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID_4=\"NETGEAR4\" >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SSID_HIDE_4=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_ISO_4=1 >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_SECMODE_4=NONE >> /etc/ath/sc_cfg <
rc: /bin/echo export AP_STARTMODE=multi11n >> /etc/ath/sc_cfg <
VAPNUM=0
VAPNUM=
VAPNUM=
Args: 1
Creating ap for NETGEAR on on IFNUM 0
APNAME ath0 IFNUM 0 ap
Added ath0 mode master
APNAME ath0 CHMODE 11ng
/etc/ath/makeVAP: 399: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent
Created ath0 mode ap for NETGEAR
/etc/ath/makeVAP 11n ap NETGEAR 0:RF:11:-1:0:1 100
VAPNUM=1
Modules already loaded
Creating ap for NETGEAR2 on on IFNUM 0
APNAME ath1 IFNUM 0 ap
Added ath1 mode master
APNAME ath1 CHMODE 11ng
Created ath1 mode ap for NETGEAR2
/etc/ath/makeVAP 11n ap NETGEAR2 0::11:-1:1:1
VAPNUM=2
Modules already loaded
Creating ap for NETGEAR3 on on IFNUM 0
APNAME ath2 IFNUM 0 ap
Added ath2 mode master
APNAME ath2 CHMODE 11ng
Created ath2 mode ap for NETGEAR3
VAPNUM=3
Modules already loaded
Creating ap for NETGEAR4 on on IFNUM 0
APNAME ath3 IFNUM 0 ap
Added ath3 mode master
APNAME ath3 CHMODE 11ng
Created ath3 mode ap for NETGEAR4
VAPNUM=4
lo        no wireless extensions.

imq0      no wireless extensions.

imq1      no wireless extensions.

imq2      no wireless extensions.

Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...

ipsec0    no wireless extensions.

ipsec1    no wireless extensions.

ipsec2    no wireless extensions.

ipsec3    no wireless extensions.

br0       no wireless extensions.

wifi0     no wireless extensions.

insmod: cannot insert `/lib/modules//wlan_scan_ap.ko': Success (17): Success

******************************************************
Wi-Fi Simple Config Application - Atheros Communcations
*********************************************************
../../common/MasterControl/Info.cpp(188):Read WSC Config File:/etc/ath/default/base_wsc_cfg.txt
../../common/MasterControl/Info.cpp(1557):Use eth0 address aa:bb:cc:dd:ee:ff
../../common/MasterControl/Info.cpp(188):Read WSC Config File:/etc/ath/wsc_config.txt
../../common/MasterControl/Info.cpp(1557):Use eth0 address aa:bb:cc:dd:ee:ff
../../common/WscCmd/WscCmd.cpp(1572):WscCmd::AP tmp file =cp /etc/ath/hostapd.open
../../common/WscCmd/WscCmd.cpp(1578):WscCmd::AP Config file copied: cmd=cp /etc/ath/hostapd.open /etc/ath/hostapd.conf
ssid=NETGEAR
../../common/WscCmd/WscCmd.cpp(1764):WscCmd::Params added to AP config file
../../common/MasterControl/Info.cpp(278):Info::Fail to Open /etc/ath/wsc_reset
../../common/WscCmd/WscCmd.cpp(594):WscCmd::cmd: /sbin/hostapd -B /etc/ath/hostapd.conf
Configuration file: /etc/ath/hostapd.conf
Using interface ath0 with hwaddr aa:bb:cc:dd:ee:ff and ssid 'NETGEAR'
../../common/InbWlan/InbWlan.cpp(244):UDP recv m_recvPort[0]= 32769
Flushing old station entries
Deauthenticate all stations
l2_packet_receive - recvfrom: Network is down
l2_packet_receive - recvfrom: Network is down
VAPNUM=4
lo        no wireless extensions.

imq0      no wireless extensions.

imq1      no wireless extensions.

imq2      no wireless extensions.

Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...

ipsec0    no wireless extensions.

ipsec1    no wireless extensions.

ipsec2    no wireless extensions.

ipsec3    no wireless extensions.

br0       no wireless extensions.

wifi0     no wireless extensions.

insmod: cannot insert `/lib/modules//wlan_scan_ap.ko': Success (17): Success
VAPNUM=4
lo        no wireless extensions.

imq0      no wireless extensions.

imq1      no wireless extensions.

imq2      no wireless extensions.

Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...

ipsec0    no wireless extensions.

ipsec1    no wireless extensions.

ipsec2    no wireless extensions.

ipsec3    no wireless extensions.

br0       no wireless extensions.

wifi0     no wireless extensions.

insmod: cannot insert `/lib/modules//wlan_scan_ap.ko': Success (17): Success
VAPNUM=4
lo        no wireless extensions.

imq0      no wireless extensions.

imq1      no wireless extensions.

imq2      no wireless extensions.

Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...

ipsec0    no wireless extensions.

ipsec1    no wireless extensions.

ipsec2    no wireless extensions.

ipsec3    no wireless extensions.

br0       no wireless extensions.

wifi0     no wireless extensions.

insmod: cannot insert `/lib/modules//wlan_scan_ap.ko': Success (17): Success
rc: wps->unconfig
wsc_det: send unconfig
rc: wps->unconfig
wsc_det: send unconfig
killall: smbd: no process killed
killall: nmbd: no process killed
killall: bftpd: no process killed
killall: smbd: no process killed
killall: nmbd: no process killed
killall: bftpd: no process killed
killall: provisioning_ap: no process killed
sh: /usr/sbin/provisioning_ap: not found
route: SIOC[ADD|DEL]RT: File exists
/usr/etc/rcS: 169: /usr/s
Please press Enter to activate this console. 

Boot of original Netgear DGN3500B firmware

Copy from Serail Flash to RAM... done
## Starting application at 0x80200000 ...
setenv kernel_addr=0x50000
setenv kernel_addr=0x50000
  
PID=YP5724

Will check KFS integrality. read KFS first
EEPROM @0x0 read: addr 0x80500000  off 0x50000  count 16384000
.....................................................................................................................................................................................e
sercomm_trap: done
check_checksum start

image=27, image+1=5, image+2=19

image-2=4D, image-1=6D, image=37

PID_Offset=0x802000, checksum_in_file=0x7017, checksum_calculat=0x7017, checksum_data_string=7017
## Application terminated, rc = 0x0
## Booting image at 00050000 ...
*** eeprom_read
*** eeprom_read

addr = 50000
CFG_LOAD_ADDR = 80100000
..................addr = 80500000

   Image Name:   MIPS Linux-2.6.20
   Created:      2010-10-04   5:41:11 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1217368 Bytes =  1.2 MB
   Load Address: 80002000
   Entry Point:  8039b000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

 **** do_bootm_linux
   commandline=root=/dev/mtdblock0 ip=192.168.1.1:192.168.1.15::::eth0:on console=ttyS1,115200 ethaddr=aa:bb:cc:dd:ee:ff phym=64M mem=64M panic=1
   argc=2
   argv[0]=bootm
   argv[1]=0x50000

Starting kernel ...

Infineon Amazon_S
mips_hpt_frequency:166666666, counter_resolution = :
Linux version 2.6.20-Amazon_S (root@build-server) (gcc version 3.4.4 20050119 (MIPS SDE)) #74 Mon Oct 4 13:41:05 CST 2010
phym = 04000000, memsz = 04000000, max_pfn = 00004000
CPU revision is: 0001954c
Determined physical RAM map:
User-defined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
  DMA zone: 128 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 16256 pages, LIFO batch:3
  Normal zone: 0 pages used for memmap
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/mtdblock0 ip=192.168.1.1:192.168.1.15::::eth0:on console=ttyS1,115200 ethaddr=aa:bb:cc:dd:ee:ff phym=64M mem=64M panic=1 
1 MIPSR2 register sets available
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
Setting up vectored interrupts
vec_vi[0]:0x803dc200: 0x8000eb88
vec_vi[1]:0x803dc400: 0x8000eb88
vec_vi[2]:0x803dc600: 0x80003df4
vec_vi[3]:0x803dc800: 0x80003ea4
vec_vi[4]:0x803dca00: 0x80003f38
vec_vi[5]:0x803dcc00: 0x80003fd8
vec_vi[6]:0x803dce00: 0x8000406c
vec_vi[7]:0x803dd000: 0x80004100
PID hash table entries: 256 (order: 8, 1024 bytes)
Using 166.667 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60920k/65536k available (2572k kernel code, 4556k reserved, 1109k data, 136k init, 0k highmem)
Calibrating delay loop... 222.00 BogoMIPS (lpj=1110016)
Mount-cache hash table entries: 512
cpu_wait is r4k_wait
NET: Registered protocol family 16
PCI: Probing PCI hardware on host bus 0.
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Infineon Technologies PCI driver version 1.0.0 
Infineon Technologies PCI driver version 1.0.0 
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
Infineon Technologies DMA driver version 1.0.0 
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
dev 0000:00:00.0: interrupt pin 1
dev 0000:00:0e.0: interrupt pin 1
Infineon Technologies GPTU driver version 1.0.0 
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
Infineon Technologies port driver version 1.0.2 
Infineon Technologies CGU driver version 1.0.0 
cgu: misc_register on minor = 62
Infineon Technologies PMU driver version 0.0.1 
Infineon Technologies WDT driver version 1.0.0 
IFX MEI Version 4.00.01

Infineon CPE API Driver version: DSL CPE API V3.20.5.1

DSL_DRV: using proc fs
ttyS0 at MMIO 0xbe100400 (irq = 98) is a IFX_ASC
ttyS1 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC
Infineon Technologies ASC driver version 1.0.0 
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 3 devices...
IMQ driver loaded successfully.
        Hooking IMQ after NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
IFX SWAPI v1 - IFX Common Ethernet Switch API, version 1.0.1.1
(c) Copyright 2008, Infineon Technologies AG
Switch Driver Version: 1.0.4
 External Switch ID :0x0000ffff


*** init rtl8366rb **
The 0x02=0x1C   (==0x1C ?)
***The 0x0=0x830    0
Logical CPU port is disabled
amazon_s_switch_set_headerstatus_pmactodma[528]: Enable PMAC to DMA
amazon_s_switch_set_headerstatus_dmatopmac[558]: Enable DMA to PMAC
SWAPI: Registered character device [ar9] with major no [244] and minor no [1]Successfully registered dev [AR9] with Genric Kernel APIinit_amazon_s_mtd: chip probing count 0
CFI: Found no Amazon_S Bank 0 device at location zero
Amazon_S: No support flash chips found!
Infineon Technologies Synchronous Serial Controller (SSC) driver version 1.1.2
amazon_s_sscAllocConnection: device amazon_s-sflash register sucessfully!
MTD driver for SPI flash.
Probing for Serial flash ...
Creating 8 MTD partitions on "amazon_s-sflash":
0x00180000-0x01000000 : "File-System"
0x00050000-0x00ff0000 : "KFS"
0x00000000-0x00010000 : "U-Boot"
0x00030000-0x00040000 : "NVRAM"
0x00000000-0x00010000 : "U-Boot"
0x00020000-0x00030000 : "DPF"
0x00010000-0x00020000 : "BOOTENV"
0x00ff0000-0x01000000 : "POT"
Infineon Technologies Synchronous SPI flash driver version 1.0.2 
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
Infineon Technologies LED driver version 1.0.0 
Infineon Technologies DEU driver version 1.0.0 
PAGE_SIZE = 4096
IFX DEU DES initialized (multiblock) (DMA).
IFX DEU AES initialized (multiblock) (DMA).
IFX DEU ARC4 initialized (multiblock) (DMA).
IFX DEU SHA1 initialized (DMA).
IFX DEU MD5 initialized (DMA).
IFX DEU SHA1_HMAC initialized (DMA).
IFX DEU MD5_HMAC initialized (DMA).
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
nf_ct_ftp: registering helper for pf: 2 port: 21
nf_ct_ftp: registering helper for pf: 10 port: 21
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 8
atmpvc_init() failed with -17
Time: MIPS clocksource has been installed.
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 136k freed
init started:  BusyBox v1.00 (2010.10.04-05:30+0000) multi-call binary
init started:  BusyBox v1.00 (2010.10.04-05:30+0000) multi-call binary
Starting pid 131, console /dev/console: '/usr/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
mount: Mounting devpts on /dev/pts failed: No such file or directory
mknod: /dev/sc_led: File exists
led_pb_api: module license 'Sercomm' taints kernel.
led_init_module : set GPIO 3, 19 to output
insmod: cannot open module `/lib/modules/ipt_string.ko': No such file or directory
netfilter PSD loaded - (c) astaro AG
ipt_random match loaded
dwc_otg: version 2.40a 10-APR-2006 (ker:20614)
dwc_otg dwc_otg: base=0xbe101000
dwc_otg dwc_otg: dwc_otg_device=0x83cc3780
DWC_otg: Using DMA mode
dwc_otg dwc_otg: DWC OTG Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
dwc_otg dwc_otg: new USB bus registered, assigned bus number 1
dwc_otg dwc_otg: irq 54, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
Enable USB0 power!!
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 2.6.20-Amazon_S dwc_otg_hcd
usb usb1: SerialNumber: dwc_otg
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
fuse init (API version 7.8)
device eth0 entered promiscuous mode
Infineon Technologies PPE driver version 1.0.0 
Logical CPU port is disabled
amazon_s_switch_set_headerstatus_pmactodma[528]: Enable PMAC to DMA
amazon_s_switch_set_headerstatus_dmatopmac[558]: Enable DMA to PMAC
Logical CPU port is enabled
Logical CPU port is disabled
amazon_s_switch_set_headerstatus_dmatopmac[558]: Enable DMA to PMAC
ppe: ATM init succeeded (drv 0.0.1, fw 5.1.0.2.1.0)
killall: dsl_cpe_control: no process killed
DSL_CPE: Using ADSL Modem is not ready!autostart script file - /etc/cmv_batch
DSL_CPE: using script notification file - /etc/xdslrc.sh
DSL_CPE: using 1st firmware file - /firmware/modemhwe.bin
DSL_CPE: Device /dev/dsl_cpe_api opened successfully
<6>[IFX_MEI_Ioctls 2680]: DSL_FIO_BSP_GET_CHIP_INFO: version 1
userspace registering PID
[IFX_MEI_DFEMemoryAlloc 1583]: image_size = 325464
[DSL_BSP_FWDownload 1752] -> IFX_MEI_BarUpdate()
wsc_det: pin=37655266
[IFX_MEI_RunAdslModem 1422] -> IFX_MEI_BarUpdate()
[IFX_MEI_IrqHandle 1936]: Got MODEM_READY_MSG
[IFX_MEI_IrqHandle 1936]: Got MODEM_READY_MSG
[IFX_MEI_RunAdslModem 1468]: Modem is ready.
ap_name=(null) action=start
vconfig: open /proc/net/vlan/config: No such file or directory
vconfig: open /proc/net/vlan/config: No such file or directory
vconfig: open /proc/net/vlan/config: No such file or directory
vconfig: open /proc/net/vlan/config: No such file or directory
device eth0 is already a member of a bridge; can't enslave it to bridge br0.
br0: port 1(eth0) entering learning state
/bin/echo GMT-1 > /etc/TZ
ap_name=firewall action=restart


DSL_CPE: Parsing script file (/etc/cmv_batch)...
WaitForConfiguration 
 Uplink bandwidth enable
<rc> fw_qos_init: rate up=512, down=0

DSL_CPE: Parsing script file (/etc/cmv_batch)...
WaitForLinkActivate 
*********** start of fw_pt ***********
===========================  fw_qos  =========================================
rules=,length=0
********************** end of qos_parse_port for apps
rules=,length=0
********************** end of qos_parse_port for game
********************** end of qos_parse_mac 
sh: cannot create /proc/sc_lan_prio: Directory nonexistent
/bin/echo "0000" > /proc/sc_lan_prio 
********************** end of qos_parse_LANport 
===========================  fw_qos end =====================================
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.2.8: host/network `(null)' not found
Try `iptables -h' or 'iptables --help' for more information.
/bin/echo GMT-1 > /etc/TZ
0:0
sh: cannot create /proc/net/ipt_condition/schedule: Directory nonexistent
PROJECT=DGN3500B_16M
killall: udhcpd: no process killed
killall: miniupnpd: no process killed
killall: dnrd: no process killed
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
dnrd -a 192.168.0.1 -m hosts -c off --timeout=0 -b 
Debug_Wsc:: wl0 is disable
killall: smbd: no process killed
killall: nmbd: no process killed
killall: bftpd: no process killed
killall: smbd: no process killed
killall: nmbd: no process killed
killall: bftpd: no process killed
killall: provisioning_ap: no process killed
sh: /usr/sbin/provisioning_ap: not found
route: SIOC[ADD|DEL]RT: File exists
/usr/etc/rcS: 132: cannot create /proc/sys/net/ipv4/ip_conntrack_max: Directory nonexistent
sh: cannot open /var/log/messages: No such file
/usr/etc/rcS: 146: cannot create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeout: Directory nonexistent
mount: Mounting /dev/mtdblock7 on /tmp/bundles failed: No such device
/usr/etc/rcS: 157: /usr/sbin/fake_utelnetd: not found

Please press Enter to activate this console. 

Back to top

toh/netgear/dgn3500b/stockboot.txt · Last modified: 2012/11/11 17:25 by danielg4