This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
toh:netgear:wg602 [2013/03/24 15:56] hauke |
toh:netgear:wg602 [2015/11/30 22:14] (current) tmomas [[meta:tags]] -> [[meta:tags|How to add tags]] |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Netgear WG602v3/4 ====== | ||
+ | **Note:** This device is not being worked on due to its low size of flash memory. | ||
+ | ===== Hardware Highlights ===== | ||
+ | ^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ | ||
+ | | Broadcom BCM5354KFBG@240 MHz | 8MiB | 2MiB | 1 x 1| No | Yes | Yes | | ||
+ | |||
+ | ===== Installation ===== | ||
+ | WIP | ||
+ | |||
+ | ==== Flash Layout ==== | ||
+ | WIP | ||
+ | |||
+ | ==== OEM easy installation ==== | ||
+ | WIP | ||
+ | |||
+ | ==== OEM installation using the TFTP method ==== | ||
+ | |||
+ | WIP | ||
+ | |||
+ | ==== Upgrading OpenWrt ==== | ||
+ | WIP | ||
+ | |||
+ | === LuCI Web Upgrade Process === | ||
+ | WIP | ||
+ | |||
+ | === Terminal Upgrade Process === | ||
+ | |||
+ | WIP | ||
+ | |||
+ | ===== Basic configuration ===== | ||
+ | |||
+ | WIP | ||
+ | |||
+ | ===== Specific Configuration ===== | ||
+ | |||
+ | ==== Failsafe mode ==== | ||
+ | -> [[doc:howto:generic.failsafe]] | ||
+ | |||
+ | ==== Buttons ==== | ||
+ | -> [[doc:howto:hardware.button]] on howto use and configure the hardware button(s). | ||
+ | |||
+ | The Netgear WG602 has only one reset button. | ||
+ | |||
+ | |||
+ | ===== Hardware ===== | ||
+ | ==== Info ==== | ||
+ | | **[[wp>Instruction set|Architecture]]:** | [[wp>MIPS architecture|MIPS]] | | ||
+ | | **Vendor:** | [[wp>Broadcam]] | | ||
+ | | **[[doc:techref:Bootloader]]:** | [[doc:techref:bootloader:cfe|CFE]] | | ||
+ | | **[[doc:hardware:soc|System-On-Chip]]:** | BCM5354KFBG | | ||
+ | | **[[doc:hardware:cpu|CPU]]/Speed** | 240MHz | | ||
+ | | **Flash-Chip:** | M12l64164A (www.esmt.com.tw/DB/manager/upload/M12L64164A.pdf) | | ||
+ | | **Flash size:** | 2 MiB | | ||
+ | | **RAM:** | 8 MiB | | ||
+ | | **Wireless:** | ? | | ||
+ | | **Ethernet:** | 1x Broadcom BCM47xx 10/100 Mbps Ethernet | | ||
+ | | **Internet:** | PPPoX DHCP | | ||
+ | | **USB:** | No | | ||
+ | | **[[doc:hardware:port.serial|Serial]]:** | [[#serial.jtag|Yes]] | | ||
+ | | **[[doc:hardware:port.jtag|JTAG]]:** | [[#serial.jtag|Yes]] | | ||
+ | |||
+ | ==== Photos ==== | ||
+ | WG602 v4 | ||
+ | |||
+ | //Front:// | ||
+ | |||
+ | {{http://kbserver.netgear.com/images/wg602v3.gif}} | ||
+ | |||
+ | //Back:// | ||
+ | |||
+ | **Photo of back of the casing** | ||
+ | |||
+ | ==== Opening the case ==== | ||
+ | **Note:** This will void your warranty! | ||
+ | |||
+ | *To remove the cover do a/b/c | ||
+ | |||
+ | //Main PCB// | ||
+ | |||
+ | **Photo of PCB** | ||
+ | |||
+ | ==== Serial & JTAG==== | ||
+ | -> [[doc:hardware:port.serial]] general information about the serial port, serial port cable, etc. | ||
+ | |||
+ | How to connect to the Serial Port of this specific device: | ||
+ | |||
+ | {{http://www.icysilence.org/wp-content/uploads/Serial-Jtag_Netgear_blog_small.png}} | ||
+ | |||
+ | |||
+ | ===== Debricking ===== | ||
+ | -> [[doc:howto:generic.debrick]] | ||
+ | |||
+ | ===== Bootloader Mods ===== | ||
+ | - you could read about [[doc:techref:bootloader:cfe]] in general | ||
+ | |||
+ | ===== Hardware mods ===== | ||
+ | - as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience! | ||
+ | |||
+ | ==== 128MiB RAM Mod ==== | ||
+ | ==== I²C GPIO Mod ==== | ||
+ | ==== I²C Tiny-USB Mod ==== | ||
+ | |||
+ | ===== Notes ===== | ||
+ | |||
+ | |||
+ | ===== Tags ===== | ||
+ | [[meta:tags|How to add tags]] | ||
+ | |||
+ | {{tag> FastEthernet DetachableAntenna bcm47xx BCM5354 MIPS MIPS32}} |