User Tools

Site Tools


toh:netgear:wn802t

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
toh:netgear:wn802t [2013/11/03 12:32]
reichhart added tag for ap83 reference design to make comparing with other routers more easy
toh:netgear:wn802t [2015/12/14 19:11] (current)
tmomas New bootlog formatting applied
Line 1: Line 1:
 +====== Netgear WN802T ======
  
 +The WN802T is a b/g/n wireless access point, capable of running OpenWRT. ​
 +
 +===== Version 2.x =====
 +
 +
 +==== Features ====
 +  * Atheros AR9132 CPU
 +  * 8 MB Flash Memory
 +  * 32 MB DDR400B RAM (Hynix HY5DU561622FTP-D43) ​
 +  * Atheros AR9103 wireless chip
 +  * Atheros AR8021 Ethernet chip
 +
 +==== Serial console ====
 +
 +The serial console connector (JP1) has the usual Netgear pinout: GND - TX - RX - VCC
 +
 +It's 115200 8N1, software flow control. It's a TTL serial port, so don't plug it directly into a RS232 port. You have to build a TTL-RS232 adaptor to attach your WN802T to your computer. With that, you can now use a null modem cable to attach it to your PCs COM port. 
 +
 +To access the boot menu, press space bar when you see "Enter SPACE to drop into boot loader:"​ and countdown from 5 to zero.
 +
 +The ethernet port is enabled in the boot loader (cable must be plugged in on boot). TFTP can be used to transfer the firmware.
 +
 +==== BootLogs ====
 +
 +
 +=== Factory Bootlog ===
 +<WRAP bootlog>
 +<​nowiki>​U-Boot 1.1.4-WN802TV2-V1.1.2 (Sep  3 2009 - 10:09:11)
 +
 +AP83 (ar9100 with SPI flash)
 +DRAM:  32 MB
 +        Finding MXIC Flash. ID c22017
 +Flash: ​ 8 MB
 +In:    serial
 +Out:   ​serial
 +Err:   ​serial
 +Net:   ​ag7100_enet_initialize...
 +        Fetching MAC Address from 0xbf7f1000
 +        MAC_CFG1 0xf MAC_CFG2 0x7114
 +        PHY Setting up...
 +        VSCXXX Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
 +PHY:   ​Atheros AR8021
 +eth0:  00:​00:​00:​00:​00:​00
 +        eth0 up
 +
 +Manu data is valid!
 +Enter SPACE to drop into boot loader: ​ 0
 +## Booting image at bf6e0000 ...
 +   Image Name:   Linux Kernel Image
 +   ​Created: ​     2012-06-07 ​  ​6:​12:​17 UTC
 +   Image Type:   MIPS Linux Kernel Image (gzip compressed)
 +   Data Size:    913746 Bytes = 892.3 kB
 +   Load Address: 80060000
 +   Entry Point: ​ 8022d000
 +   ​Verifying Kernel Checksum ... OK
 +   ​Uncompressing Kernel Image ... OK
 +
 +Starting kernel @8022d000...
 +
 +Linux version 2.6.15--LSDK-7.1.3.29-WN802Tv2_V3.1.12 (root@localhost.localdomain) (gcc version 3.4.4) #200 Thu Jun 7 11:42:02 IST 2012
 +flash_size passed from bootloader = 8
 +arg 1: console=ttyS0,​115200
 +arg 2: rootfstype=jffs2
 +arg 3: root=31:02
 +init=/​sbin/​init
 +arg 4: mtdparts=ar7100-nor0:​256k(u-boot),​64k(u-boot-env),​6720k(rootfs),​1024k(uImage),​64k(manufacturing-data),​64k(ART)
 +arg 5: mem=32M
 +CPU revision is: 00019374
 +Determined physical RAM map:
 + ​memory:​ 02000000 @ 00000000 (usable)
 +User-defined physical RAM map:
 + ​memory:​ 02000000 @ 00000000 (usable)
 +Built 1 zonelists
 +Kernel command line: console=ttyS0,​115200 rootfstype=jffs2 root=31:02
 +init=/​sbin/​init mtdparts=ar7100-nor0:​256k(u-boot),​64k(u-boot-env),​6720k(rootfs),​1024k(uImage),​64k(manufacturing-data),​64k(ART) mem=32M
 +Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
 +Primary data cache 32kB, 4-way, linesize 32 bytes.
 +Synthesized TLB refill handler (20 instructions).
 +Synthesized TLB load handler fastpath (32 instructions).
 +Synthesized TLB store handler fastpath (32 instructions).
 +Synthesized TLB modify handler fastpath (31 instructions).
 +Cache parity protection disabled
 +PID hash table entries: 256 (order: 8, 4096 bytes)
 +Using 200.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 30020k/​32768k available (1520k kernel code, 2732k reserved, 319k data, 104k init, 0k highmem)
 +Mount-cache hash table entries: 512
 +Checking for '​wait'​ instruction... ​ available.
 +NET: Registered protocol family 16
 +reset dev success
 +SCSI subsystem initialized
 +AR7100 GPIOC major 0
 +JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
 +Initializing Cryptographic API
 +io scheduler noop registered
 +io scheduler deadline registered
 +Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled
 +serial8250.0:​ ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
 +6 cmdlinepart partitions found on MTD device ar7100-nor0
 +Creating 6 MTD partitions on "​ar7100-nor0":​
 +0x00000000-0x00040000 : "​u-boot"​
 +0x00040000-0x00050000 : "​u-boot-env"​
 +0x00050000-0x006e0000 : "​rootfs"​
 +0x006e0000-0x007e0000 : "​uImage"​
 +0x007e0000-0x007f0000 : "​manufacturing-data"​
 +0x007f0000-0x00800000 : "​ART"​
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 512 (order: -1, 2048 bytes)
 +TCP established hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +TCP bic registered
 +NET: Registered protocol family 1
 +NET: Registered protocol family 17
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +ar7100wdt_init:​ Registering WDT success
 +VFS: Mounted root (jffs2 filesystem) readonly.
 +Freeing unused kernel memory: 104k freed
 +init started: ​ BusyBox v1.01 (2012.06.07-06:​08+0000) multi-call binary
 +ag7100_mod: module license '​unspecified'​ taints kernel.
 +AG7100: Length per segment 1536
 +AG7100: Max segments per packet 1
 +AG7100: Max tx descriptor count    100
 +AG7100: Max rx descriptor count    252
 +AG7100: fifo cfg 3 00780008
 +AG7100CHH: Mac address for unit 0
 +AG7100CHH: e0:​91:​f5:​cd:​31:​90
 +*** Loading wlandriver
 +*** Country code is 840
 +*** Base MAC address is 00:​00:​00:​00:​00:​00
 +ath_hal: 0.9.17.1 ( AR5416,​DEBUG,​REGOPS_FUNC,​DFS)
 +asc: no version for "​ath_hal_tx_txpc"​ found: kernel tainted.
 +arada_softchip:​ 0.1.0.0
 +ath ratectrl: ath_rate_atherosCopyright (c) 2001-2005 Atheros Communications,​ Inc, All Rights Reserved
 +wlan: mac acl policy registered
 +ath_ahb: 1.0 (Atheros/​multi-bss)
 + In asc_attach , enable_pktlog = 0
 +ath ratectrl: ath_rate_atherosCopyright (c) 2001-2005 Atheros Communications,​ Inc, All Rights Reserved
 +mac 20.0 phy 10.2 radio 13.0
 +wifi0: Atheros AR9100 WiSoC: mem=0xb80c0000,​ irq=2
 +Creating AP mode
 +Creating wds vaps
 +*** Starting configd
 +*** Starting watchdog
 +*** Starting reset_detect
 +wn802t_reset_open:​ called
 +wn302t_sys_ioctl:​ cmd issued is  1015
 +*** Starting httpd server
 +1999-12-31 16:00:05: (server.c.918) WARNING: unknown config-key: accesslog.filename (ignored)
 +*** Creating soft link for syslog binary
 +ln: /​bin/​syslogd:​ File exists
 +*** Creating softlink for syslog messages
 +killall: syslogd: no process killed
 +passwd: Unknown user admin
 +
 +kill: Could not kill pid '​129':​ No such process
 +time-b.netgear.com:​ Unknown host
 +device eth0 entered promiscuous mode
 +ag7100_ring_alloc Allocated 1200 at 0x81ee6000
 +ag7100_ring_alloc Allocated 3024 at 0x818f4000
 +AG7100: cfg1 0xf cfg2 0x7014
 +VSC8601: Found 0  unit 0:0  phy_addr: 1  id: 004dd04e
 +VSC8601: PHY is an Atheros F1E
 +VSC8601: unit 0  phy_addr 1
 +VSC8601: unit 0  phy_addr 1
 +AG7100: unit 0: phy not up carrier 1
 +Writing 4
 +never heard of command [brtrunk]
 +Usage: brctl [commands]
 +commands:
 +        addbr           <​bridge> ​               add bridge
 +        delbr           <​bridge> ​               delete bridge
 +        addif           <​bridge>​ <​device> ​      add idevice wifi0vap0 entered promiscuous mode
 +nterface to bridge
 +        delif           <​bridge>​ <​device> ​      ​delete interface from bridge
 +        setageing ​      <​bridge>​ <​time> ​        set ageing time
 +        setbridgeprio ​  <​bridge>​ <​prio> ​        set bridge prioritdevice wifi0wds0 entered promiscuous mode
 +y
 +        setfd           <​bridge>​ <​time> ​        set bridge forward delay
 +        sethello ​       <​bridge>​ <​time> ​        set hello time
 +        setmaxage ​      <​bridge>​ <​time> ​        set max message age
 +        setpathcost ​    <​bridge>​ <device wifi0wds1 entered promiscuous mode
 +port> <​cost> ​   set path cost
 +        setportprio ​    <​bridge>​ <​port>​ <​prio> ​ set port priority
 +        show                                    show a list of bridges
 +        showmacs ​       <​bridge> ​               show a list of mac addrs
 +        showsdevice wifi0wds2 entered promiscuous mode
 +tp      <​bridge> ​               show bridge stp info
 +        stp             <​bridge>​ {on|off} ​      turn stp on/off
 +device wifi0wds3 entered promiscuous mode
 +device wifi0wds4 entered promiscuous mode
 +device wifi0wds5 entered promiscuous mode
 +route: SIOC[ADD|DEL]RT:​ Invalid argument
 +no /​usr/​sbin/​nmbd found; none killed.
 +brtrunk: port 2(wifi0vap0) entering learning state
 +brtrunk: port 2(wifi0vap0) entering disabled state
 +brtrunk: port 2(wifi0vap0) entering learning state
 +VSC8601: unit 0  phy_addr 1
 +AG7100: unit 0 phy is up...RGMii 1000Mbps full duplex
 +AG7100: pll reg 0x18050014: 0x13000a44 ​ AG7100: cfg_1: 0x7ff0000
 +AG7100: cfg_2: 0xfff
 +AG7100: cfg_3: 0x780008
 +AG7100: cfg_4: 0xffff
 +AG7100: cfg_5: 0x7ffef
 +AG7100: done cfg2 0x7115 ifctl 0x10000 miictrl 0x12
 +brtrunk: port 1(eth0) entering learning state
 +
 + ​netgearCD3190 mips #200 Thu Jun 7 11:42:02 IST 2012 (none)
 +netgearCD3190 login: Value = 3
 +brtrunk: topology change detected, propagating
 +brtrunk: port 2(wifi0vap0) entering forwarding state
 +brtrunk: topology change detected, propagating
 +brtrunk: port 1(eth0) entering forwarding state
 +
 + ​netgearCD3190 mips #200 Thu Jun 7 11:42:02 IST 2012 (none)
 +netgearCD3190 login: root
 +Password:
 +
 +
 +BusyBox v1.01 (2012.06.07-06:​08+0000) Built-in shell (ash)
 +Enter '​help'​ for a list of built-in commands.
 +
 +~ # cat /​proc/​cpuinfo
 +system type             : Atheros AR9100
 +processor ​              : 0
 +cpu model               : MIPS 24K V7.4
 +BogoMIPS ​               : 265.21
 +wait instruction ​       : yes
 +microsecond timers ​     : yes
 +tlb_entries ​            : 16
 +extra interrupt vector ​ : yes
 +hardware watchpoint ​    : yes
 +ASEs implemented ​       : mips16
 +VCED exceptions ​        : not available
 +VCEI exceptions ​        : not available
 +~ # cat /​proc/​meminfo
 +MemTotal: ​       30140 kB
 +MemFree: ​        19860 kB
 +Buffers: ​            0 kB
 +Cached: ​          2624 kB
 +SwapCached: ​         0 kB
 +Active: ​          1860 kB
 +Inactive: ​        1504 kB
 +HighTotal: ​          0 kB
 +HighFree: ​           0 kB
 +LowTotal: ​       30140 kB
 +LowFree: ​        19860 kB
 +SwapTotal: ​          0 kB
 +SwapFree: ​           0 kB
 +Dirty: ​              0 kB
 +Writeback: ​          0 kB
 +Mapped: ​          2188 kB
 +Slab:             5056 kB
 +CommitLimit: ​    15068 kB
 +Committed_AS: ​    7664 kB
 +PageTables: ​       180 kB
 +VmallocTotal: ​ 1048560 kB
 +VmallocUsed: ​     1504 kB
 +VmallocChunk: ​ 1046772 kB
 +~ # cat /proc/mtd
 +dev:    size   ​erasesize ​ name
 +mtd0: 00040000 00010000 "​u-boot"​
 +mtd1: 00010000 00010000 "​u-boot-env"​
 +mtd2: 00690000 00010000 "​rootfs"​
 +mtd3: 00100000 00010000 "​uImage"​
 +mtd4: 00010000 00010000 "​manufacturing-data"​
 +mtd5: 00010000 00010000 "​ART"​
 +~ # cat /​proc/​partitions
 +major minor  #​blocks ​ name
 +
 +  31     ​0 ​       256 mtdblock0
 +  31     ​1 ​        64 mtdblock1
 +  31     ​2 ​      6720 mtdblock2
 +  31     ​3 ​      1024 mtdblock3
 +  31     ​4 ​        64 mtdblock4
 +  31     ​5 ​        64 mtdblock5
 +~ # cat /​proc/​version
 +Linux version 2.6.15--LSDK-7.1.3.29-WN802Tv2_V3.1.12 (root@localhost.localdomain) (gcc version 3.4.4) #200 Thu Jun 7 11:42:02 IST 2012
 +~ #</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​atheros-ap83}}