Netgear WNCE2001

Supported Versions

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Notes
? - - Barrier Breaker r36289 -

Hardware Highlights

Rev CPU Ram Flash WiFi Network USB Serial JTag
? Ralink RT3052F@384MHz 32MiB 4MiB 2x2 2.4Ghz 802.11n 300MiBit/s 1 x 10/100MiBit/s No Yes Possibly on testpads

The device has two non-detachable internal antennas.

Manufacturer's site: http://www.netgear.com/landing/wnce2001.aspx

Hardware

Info

Rev ?

Architecture: MIPS
Vendor: Ralink
Bootloader: U-Boot
System-On-Chip: RT3052 (MIPS 24K V4.12)
CPU/Speed 384 Mhz
Flash-Chip: Macronix MX29LV320
Flash size: 4096 KiB
RAM: 32 MiB
Wireless: RT3052 2x2 802.11n 2.4GHz
Ethernet: 1x 10/100MiBit/s
USB: No
Serial: Yes
JTAG: Maybe on testpads

U-Boot recovery mode

If the checksum check fails, u-boot enters tftp recovery mode. It will listen on IP 192.168.1.251 and accept new factory images via tftp (don't forget to set binary mode). Recovery mode is indicated by the power led lighting up briefly in red, followed by about 1-second interval green blinking. This can be used to go back to the stock firmware, by deliberately erasing the checksum partition.

Stock firmware

The stock firmware is running a tftpd, which allows you to get files without authentication, e.g. "get /bin/busybox" or "get /dev/mtdblock1".

The u-boot on this device does a simple checksum check of kernel+rootfs against the 'checksum' partition. If it fails, it enters tftp recovery mode (power led blinking green), waiting for a stock image (including headers) on ip 192.168.1.251:

U-Boot 1.1.3 (Jul 2 2010 - 09:49:13) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb4000 spi_wait_nsec: 3e spi deice id: c2 20 16 c2 20 (2016c220) find flash: mx25l3205d raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 3.3 -------------------------------------------- ASIC 3052_MP2 (Port5<->None) DRAM component: 256 Mbits SDR DRAM bus: 16 bit Total memory: 32 MBytes Flash component: SPI Flash Date:Jul 2 2010 Time:09:49:13 Cameo Version: v1.00 Build:07 Module Name: Netgear WNCE-2001 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 384 MHZ #### SDRAM bus set to 16 bit SDRAM size =32 Mbytes Please choose the operation: 0: Don't check the image's checksum. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. 0 raspi_read: from:a0000 len:50 raspi_read: from:b0000 len:240004 NetTxPacket = 0x81FE5900 KSEG1ADDR(NetTxPacket) = 0xA1FE5900 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done Header Payload scatter function is Disable !! ETH_STATE_ACTIVE!! The Router is in TFTP Server Firmware Recovery mode NOW! Listening on Port : 69, IP Address: 192.168.1.251... checksum bad

Serial

port.serial general information about the serial port, serial port cable, etc.

Netgear WNCE2001 serial pinout

VLAN config

Hardware supports full VLAN capabilities including trunking. Supported sincer33299

Multi-BSS operation

The hardware and the driver should support running up to 8 APs simultaneously, but currently it doesn't work, see https://patchwork.kernel.org/patch/1277291/ .

Stock firmware bootlog

U-Boot 1.1.3 (Jul 2 2010 - 09:49:13) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb4000 spi_wait_nsec: 3e spi deice id: c2 20 16 c2 20 (2016c220) find flash: mx25l3205d raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 3.3 -------------------------------------------- ASIC 3052_MP2 (Port5<->None) DRAM component: 256 Mbits SDR DRAM bus: 16 bit Total memory: 32 MBytes Flash component: SPI Flash Date:Jul 2 2010 Time:09:49:13 Cameo Version: v1.00 Build:07 Module Name: Netgear WNCE-2001 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 384 MHZ #### SDRAM bus set to 16 bit SDRAM size =32 Mbytes Please choose the operation: 0: Don't check the image's checksum. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 3 ^H^H^H 0 raspi_read: from:a0000 len:50 raspi_read: from:b0000 len:2c0000 3: System Boot system code via Flash. ## Booting image at bf0b0000 ... raspi_read: from:b0000 len:40 Image Name: Linux Kernel Image Created: 2010-11-09 10:28:43 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 762113 Bytes = 744.3 kB Load Address: 80000000 Entry Point: 8022b000 raspi_read: from:b0040 len:ba101 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8022b000) ... ## Giving linux memsize in MB, 32 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.21 (root@minlee-linux) (gcc version 3.4.2) #395 Tue Nov 9 18:25:43 CST 2010 The CPU feqenuce set to 384 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console=ttyS1,115200 root=/dev/mtdblock7 init=/sbin/init Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = 80800008, status = 1100ff00 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4koff... 00177000(1536000) CPU frequency 384.00 MHz Using 192.000 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 30068k/32768k available (1869k kernel code, 2700k reserved, 347k data, 100k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered Load RT2880 Timer Module(Wdg/Soft) squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro io scheduler noop registered (default) Ralink gpio driver initialized HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A rdm_major = 254 block2mtd: version $Revision: 1.1.1.1 $ deice id : c2 20 16 c2 20 (2016c220) mx25l3205d(c2 20160000) (4096 Kbytes) mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 8 MTD partitions on "raspi": 0x00000000-0x00030000 : "Bootloader" 0x00030000-0x00040000 : "Factory" 0x00040000-0x00060000 : "Config" 0x00060000-0x00090000 : "Language" 0x00090000-0x000a0000 : "POT" 0x000a0000-0x000b0000 : "CheckSum" 0x000b0000-0x00170000 : "Kernel" 0x00170000-0x00400000 : "RootFS" TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 100k freed init started: BusyBox v1.01 (2010.11.09-10:28+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 Init System... Start Tftpd... TFTP main standard_tftp_server launched on port 69. module info: clear_dev_counters init - debug mode is disabled Please press Enter to activate this console. GDMA1_MAC_ADRH -- : 0x00000000 GDMA1_MAC_ADRL -- : 0x00000000 Ralink APSoC Ethernet Driver Initilization. v2.00 256 rx/tx descriptors allocated, mtu = 1500! GDMA1_MAC_ADRH -- : 0x0000000c GDMA1_MAC_ADRL -- : 0x43288005 PROC INIT OK! 256+0 records in 256+0 records out Start RT3052 Switch daemon... Start Reset GPIO... Start WPS GPIO... Start Mode GPIO... rt2860v2_sta: module license 'unspecified' taints kernel. === pAd = c0025000, size = 494128 === <-- RTMPAllocAdapterBlock, Status=0 RX DESC a1cdc000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 Read EEPROM, EthCloneMac is [redacted]! 3. Phy Mode = 9 MCS Set = ff ff 00 00 01 <==== rt28xx_init, Status=0 0x1300 = 00064300 killall: wsc_notifier: no process killed phy_tx_ring = 0x01940000, tx_ring = 0xa1940000 phy_rx_ring = 0x00000000, rx_ring = 0x00000000 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 10000 device ra0 entered promiscuous mode ra2880stop()...Done Free TX/RX Ring Memory! GDMA1_MAC_ADRH -- : 0x0000e046 GDMA1_MAC_ADRL -- : 0x9a336266 phy_tx_ring = 0x01d4d000, tx_ring = 0xa1d4d000 phy_rx_ring = 0x01941000, rx_ring = 0xa1941000 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 10000 device eth2 entered promiscuous mode ##### config RT3052 no vlan partition ##### switch reg write offset=14, value=5555 switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1001 switch reg write offset=4c, value=1 switch reg write offset=50, value=2001 switch reg write offset=70, value=ffffffff switch reg write offset=98, value=7f7f switch reg write offset=e4, value=0 Start Lighttpd... 384+0 records in 384+0 records out tar: Invalid tar magic killall: netbios_checker: no process killed killall: udhcpd: no process killed killall: udhcpc: no process killed DHCP client start. Jan 1 00:00:16 udhcpc[184]: DHCP client start. killall: check_conn_status: no process killed br0: port 2(eth2) entering learning state br0: port 1(ra0) entering learning state Sending discover... Jan 1 00:00:16 udhcpc[184]: Sending discover... killall: klogd: no process killed killall: syslogd: no process killed br0: topology change detected, propagating br0: port 2(eth2) entering forwarding state br0: topology change detected, propagating br0: port 1(ra0) entering forwarding state Sending discover... DHCPC get gateway = 192.168.x.y Sending select for 192.168.x.z... Lease of 192.168.x.z obtained, lease time 3600 deleting routers route: SIOC[ADD|DEL]RT: No such process adding dns 192.168.x.y adding dns 8.8.8.8 Rcv Wcid(1) AddBAReq Start Seq = 00000003 the POT value reaches to the max value. tar: Removing leading '/' from member names 81+0 records in 81+0 records out Set: phy[0].reg[0] = 3900 Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Set: phy[4].reg[0] = 3900 switch reg write offset=a4, value=9 Set: phy[0].reg[0] = 3100 switch reg write offset=a4, value=9 killall: wlan_cli_notifier: no process killed

OpenWRT bootlog

U-Boot 1.1.3 (Jul 2 2010 - 09:49:13) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb4000 spi_wait_nsec: 3e spi deice id: c2 20 16 c2 20 (2016c220) find flash: mx25l3205d raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 3.3 -------------------------------------------- ASIC 3052_MP2 (Port5<->None) DRAM component: 256 Mbits SDR DRAM bus: 16 bit Total memory: 32 MBytes Flash component: SPI Flash Date:Jul 2 2010 Time:09:49:13 Cameo Version: v1.00 Build:07 Module Name: Netgear WNCE-2001 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 384 MHZ #### SDRAM bus set to 16 bit SDRAM size =32 Mbytes Please choose the operation: 0: Don't check the image's checksum. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. ^H^H^H 0 raspi_read: from:a0000 len:50 raspi_read: from:b0000 len:0 3: System Boot system code via Flash. ## Booting image at bf0b0000 ... raspi_read: from:b0000 len:40 Image Name: MIPS OpenWrt Linux-3.10.24 Created: 2014-01-05 1:03:21 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 971238 Bytes = 948.5 kB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:b0040 len:ed1e6 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 32 Starting kernel ... [ 0.000000] Linux version 3.10.24 (ranma@nukunuku) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39202) ) #1 Sun Jan 5 02:01:29 CET 2014 [ 0.000000] SoC Type: Ralink RT3052 id:1 rev:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is Netgear WNCE2001 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 29416k/32768k available (2124k kernel code, 3352k reserved, 530k data, 160k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:128 [ 0.000000] CPU Clock: 384MHz [ 0.000000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] pinctrl core: initialized pinctrl subsystem [ 0.090000] NET: Registered protocol family 16 [ 0.130000] bio: create slab at 0 [ 0.130000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.140000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.150000] Switching to clocksource MIPS [ 0.160000] NET: Registered protocol family 2 [ 0.160000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.170000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.170000] TCP: Hash tables configured (established 512 bind 512) [ 0.180000] TCP: reno registered [ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.190000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.190000] NET: Registered protocol family 1 [ 0.200000] rt-timer 10000100.timer: maximum frequncy is 7812Hz [ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.250000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.260000] msgmni has been set to 57 [ 0.260000] io scheduler noop registered [ 0.270000] io scheduler deadline registered (default) [ 0.270000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.280000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.290000] console [ttyS0] enabled, bootconsole disabled [ 0.290000] console [ttyS0] enabled, bootconsole disabled [ 0.310000] m25p80 spi32766.0: mx25l3205d (4096 Kbytes) [ 0.320000] 7 ofpart partitions found on MTD device spi32766.0 [ 0.320000] Creating 7 MTD partitions on "spi32766.0": [ 0.330000] 0x000000000000-0x000000030000 : "u-boot" [ 0.340000] 0x000000030000-0x000000040000 : "factory" [ 0.350000] 0x000000040000-0x000000060000 : "config" [ 0.350000] 0x000000060000-0x000000090000 : "language" [ 0.360000] 0x000000090000-0x0000000a0000 : "pot" [ 0.370000] 0x0000000a0000-0x0000000b0000 : "checksum" [ 0.380000] 0x0000000b0000-0x000000400000 : "firmware" [ 0.390000] 0x00000019d226-0x000000400000 : "rootfs" [ 0.390000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.410000] mtd: device 7 (rootfs) set to be root filesystem [ 0.410000] mtd: partition "rootfs_data" created automatically, ofs=0x3a0000, len=0x60000 [ 0.420000] 0x0000003a0000-0x000000400000 : "rootfs_data" [ 0.440000] eth0: done loading [ 0.450000] rt2880_wdt 10000120.watchdog: Initialized [ 0.450000] TCP: cubic registered [ 0.460000] NET: Registered protocol family 17 [ 0.460000] 8021q: 802.1Q VLAN Support v1.8 [ 0.490000] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 0.500000] Freeing unused kernel memory: 160K (80298000 - 802c0000) procd: Console is alive procd: - watchdog - procd: - preinit - Board is WNCE2001, updating checksum partition... Checksum is set, zeroing. Unlocking checksum ... Writing from /tmp/wnce2001_checksum to checksum ... [ 7.130000] usbcore: registered new interface driver usbfs [ 7.130000] usbcore: registered new interface driver hub [ 7.160000] usbcore: registered new device driver usb [ 7.200000] dwc_otg: version 2.72a 24-JUN-2008 [ 7.210000] leds-gpio gpio-leds.3: pins are not configured from the driver Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level mount_root: jffs2 is not ready - EOF marker found procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 13.350000] NET: Registered protocol family 10 [ 13.370000] nf_conntrack version 0.5.0 (462 buckets, 1848 max) [ 13.390000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 13.430000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093 [ 13.430000] Backport generated by backports.git backports-20130802-0-gdb67a3f [ 13.450000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 13.520000] xt_time: kernel timezone is -0000 [ 13.560000] cfg80211: Calling CRDA to update world regulatory domain [ 13.570000] cfg80211: World regulatory domain updated: [ 13.570000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 13.580000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 13.590000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 13.590000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 13.600000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 13.610000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 13.620000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 13.720000] PPP generic driver version 2.4.2 [ 13.720000] NET: Registered protocol family 24 [ 13.780000] rt2800_wmac 10180000.wmac: failed to load eeprom property [ 13.790000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'. [ 13.970000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected [ 13.980000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected [ 21.870000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 21.900000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 21.900000] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 25.330000] device eth0 entered promiscuous mode [ 25.350000] br-lan: port 1(eth0) entered forwarding state [ 25.350000] br-lan: port 1(eth0) entered forwarding state done. [ 25.920000] jffs2: notice: (692) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. procd: - init complete - [ 27.350000] br-lan: port 1(eth0) entered forwarding state BusyBox v1.19.4 (2014-01-05 01:57:04 CET) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r39202) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#

Tags

For some Help with the Tags, please have a look here: tags

Back to top

toh/netgear/wnce2001.txt · Last modified: 2014/03/19 01:24 by danitool