User Tools

Site Tools


toh:netis:wf-2881

Netis WF-2881 (WF2881)

A gateway manufactured by Netis Korea aimed for the South Korean market and is currently only sold via the auction site GMarket (available in english)

The router was also available on eBay, but is temporarily unavailable:

eBay (US) with OpenWrt pre-installed.

eBay (UK) with OpenWrt pre-installed.

It's similar to other platforms based on the Mediatek MT7621A SoC with the exception that it comes with 128Mbyte of flash memory.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
WF-2881MediaTek MT7621AT2x 880128NAND128MediaTek MT7602EN (onboard), MT7612EN (onboard)b/g/na/n/ac5No1x 3.0

Installation

Flashing

Flashing openwrt void your warranty.
Use your own risk!

Currently you can only install OpenWRT by using stock webshell or U-Boot
Sysupgrade is supported by device and is the recommended way of upgrading.

M1200AC only can use U-Boot method.

OEM installation using the stock web shell

If device is bricked,
The only way to debrick is via UART

Before you start, setup tftp server, prepare sysupgrade.bin for WF-2881 and rename it to fw.bin

  1. upgrade router to version 1.8.0 (since 1.8.1 secret password seems to be changed, just downgrade to 1.8.0)
  2. login router admin page (default address http://192.168.1.1)
  3. go to stock web shell /syscmd.htm
  4. type secret password 'netis-yun' in input box
  5. type 'cd /tmp && tftp -g -r fw.bin <your tftp server ip>'
  6. check your firmware downloaded completely with 'ls -all /tmp/fw.bin' (file size check)
  7. 'mtd_write write /tmp/fw.bin mtd4 && reboot'

OEM installation using the TFTP method

The device can be flashed via bootloader (U-Boot), serial connection is needed.
Settings: 57600, 8N1

  1. Select option 2
  2. If you see warning, Press 'Y'
  3. Set your desired tftp client ip, server ip, file name (openwrt-ramips-mt7621-WF-2881-squashfs-sysupgrade.bin)

Debricking

only serial method is possible
generic.debrick

Failsafe mode

Doesn't currently work on this device.
generic.failsafe

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Buttons

The Netis WF-2881 has only one button

BUTTON GPIO Event Active in
WPS 12 reset Low

Hardware

Info

General
Brand Netis
Model WF-2881
Versions
Device Type WiFi Router
Availability Available
Comments - general
OpenWrt Support
Supported Since Revision https://dev.openwrt.org/changeset/47619
Supported Since Release -
Supported Current Release DD trunk
Unsupported
Hardware
Instruction set MIPS32
Sub Instruction Set MIPS32 1004K series
Bootloader U-Boot
Target ramips
System-On-Chip MediaTek MT7621AT
CPU MHz 2x 880
Flash MB 128NAND
RAM MB 128
Network
Ethernet 100M ports
Ethernet Gbit ports 5
Switch MediaTek MT7530
Modem No
VLAN ¿
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware
Detachable Antennas -
Comments - WLAN 2x 2x2:2 MIMO
Interfaces
USB ports 1x 3.0
SATA ports -
Serial Yes
JTAG No
Comments - USB & SATA ports
Misc
LED count 10
Button count 1
Power supply 12 VDC, 2.0 A
Links
Forum Topic URL
WikiDevi URL
OEM device homepage URL http://netiskorea.co.kr/product.php?uid=50&model=WF2881
Firmware OEM Stock URL http://netiskorea.co.kr/atboard.php?grp1=support&grp2=download
Firmware OpenWrt Install URL
Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/snapshots/trunk/ramips/mt7621/openwrt-ramips-mt7621-wf-2881-squashfs-sysupgrade.bin
Edit the underlying data View/Edit data

Photos

Serial

port.serial general information about the serial port, serial port cable, etc.

There is J4 connector for UART

Information!
The serial header(J4) has plated through holes which are solder filled.
The solder needs to be removed prior to fitting and soldering the new header pins

JTAG

R70 JTMS
R65 JTMS (1k PULL UP)
R66 JTDO
R65 JTDO (1k PULL UP)
R67 JTDI (1k PULL UP)
R68 JTRST_N (1k PULL DOWN)
R64 JTCLK (1k PULL DOWN)

Bootloader Mods

Bootlogs

OEM bootlog

=================================================================== MT7621 stage1 code 10:40:45 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11000000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL4 FB_DL: 0x7, 1/0 = 519/505 1D000000 PLL3 FB_DL: 0xd, 1/0 = 585/439 35000000 PLL2 FB_DL: 0xf, 1/0 = 581/443 3D000000 do DDR setting..[00320381] Apply DDR3 Setting...(use default AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 opt_dle value:11 DRAMC_R0DELDLY[018]=00001F20 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 9 13 13 11 11 11 10 8 10 10 | 11 11 10 13 10 12 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =32 DQS1 = 31 ================================================================== bit DQS0 bit DQS1 0 (1~62)31 8 (1~59)30 1 (0~59)29 9 (1~59)30 2 (1~61)31 10 (1~61)31 3 (1~62)31 11 (1~60)30 4 (1~63)32 12 (1~61)31 5 (1~63)32 13 (1~60)30 6 (1~60)30 14 (1~61)31 7 (1~64)32 15 (1~61)31 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 14 12 14 14 11 11 13 10 9 11 10 | 11 12 10 14 10 12 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff008a dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0080 DQ loop=13, cmp_err_1 = ffff0080 DQ loop=12, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=12, finish count=2 byte:0, (DQS,DQ)=(9,8) byte:1, (DQS,DQ)=(8,8) 20,data:89 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Mar 13 2015 - 13:09:18) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb0000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 87fe1c30 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 1D C2] Device found in MTK table, ID: c2f1, EXT_ID: 801dc2 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ..============================================ Ralink UBoot Version: 4.2.0.6 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Mar 13 2015 Time:13:09:18 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN LLLLW Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. 3: System Boot system code via Flash. ## Booting image at 80a00000 ... Image Name: WF2881_1.8.0_retail Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 12235048 Bytes = 11.7 MB Load Address: 80001000 Entry Point: 8000f500 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000f500) ... ## Giving linux memsize in MB, 128 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #2748 SMP Fri Sep 11 11:39:15 KST 2015 The CPU feqenuce set to 880 MHz GCMP present CPU revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 Detected 3 available secondary CPU(s) PERCPU: Embedded 7 pages/cpu @81152000 s6464 r8192 d14016 u65536 pcpu-alloc: s6464 r8192 d14016 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS1,57600 root=/dev/ram0 rootfstype=squashfs,jffs2 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Writing ErrCtl register=000004b0 Readback ErrCtl register=000004b0 Memory: 113124k/131072k available (5011k kernel code, 17948k reserved, 1798k data, 9636k init, 0k highmem) Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Trying to install interrupt handler for IRQ24 Trying to install interrupt handler for IRQ25 Trying to install interrupt handler for IRQ22 Trying to install interrupt handler for IRQ9 Trying to install interrupt handler for IRQ10 Trying to install interrupt handler for IRQ11 Trying to install interrupt handler for IRQ12 Trying to install interrupt handler for IRQ13 Trying to install interrupt handler for IRQ14 Trying to install interrupt handler for IRQ16 Trying to install interrupt handler for IRQ17 Trying to install interrupt handler for IRQ18 Trying to install interrupt handler for IRQ19 Trying to install interrupt handler for IRQ20 Trying to install interrupt handler for IRQ21 Trying to install interrupt handler for IRQ23 Trying to install interrupt handler for IRQ26 Trying to install interrupt handler for IRQ27 Trying to install interrupt handler for IRQ28 Trying to install interrupt handler for IRQ15 Trying to install interrupt handler for IRQ8 Trying to install interrupt handler for IRQ29 Trying to install interrupt handler for IRQ30 Trying to install interrupt handler for IRQ31 console [ttyS1] enabled Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu2 launch: cpu2 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. launch: starting cpu3 launch: cpu3 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Brought up 4 CPUs Synchronize counters across 4 CPUs: done. NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x60400000-0x6040ffff] (PCI address [0x60400000-0x6040ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] pci 0000:00:01.0: BAR 1: set to [mem 0x60410000-0x6041ffff] (PCI address [0x60410000-0x6041ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff 64bit] (PCI address [0x60200000-0x602fffff] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref] pci 0000:00:01.0: PCI bridge to [bus 02-02] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60400000 res[1]->end = 6040ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60410000 res[1]->end = 6041ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60200000 res[0]->end = 602fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 128 (order: 0, 4096 bytes) UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) NTFS driver 2.1.29 [Flags: R/W]. fuse init (API version 7.15) msgmni has been set to 220 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) ---------------------gpiomode: 0xa05a8------------------- Ralink gpio driver initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A brd: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 810335c0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 1D C2, 00801dc2] Device found in MTK table, ID: c2f1, EXT_ID: 801dc2 Support this Device in MTK table! c2f1 NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit) [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Creating 6 MTD partitions on "MT7621-NAND": 0x000000000000-0x000007f80000 : "ALL" 0x000000000000-0x000000080000 : "Bootloader" 0x000000080000-0x000000100000 : "Config" 0x000000100000-0x000000140000 : "Factory" 0x000000140000-0x000008000000 : "Kernel" mtd: partition "Kernel" extends beyond the end of device "MT7621-NAND" -- size truncated to 0x7e40000 0x000007f80000-0xfffffffffff80000 : "FLAT" mtd: partition "FLAT" is out of reach -- disabled [mtk_nand] probe successfully! rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000048d GMAC1_MAC_ADRL -- : 0x38b4981e Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000048d GMAC1_MAC_ADRL -- : 0x38b4981e PROC INIT OK! PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered MPPE/MPPC encryption/compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 IMQ driver loaded successfully. Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. usbcore: registered new interface driver catc catc: v2.8:CATC EL1210A NetMate USB Ethernet driver usbcore: registered new interface driver asix usbcore: registered new interface driver ax88179_178a usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus register rt2860 === pAd = c0282000, size = 2096728 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0180000, csr_addr=0xc0180000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap.dat Open file "/etc/Wireless/iNIC/iNIC_ap.dat" failed! ########################################### ########################################### Read Parameters from default_profile_buffer ########################################### ########################################### cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is efuse and the information is too less to bring up the interface Force to use Flash mode NVM is FLASH mode (pAd->flash_offset = 0x48000) get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai === pAd = c0602000, size = 2096728 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0500000, csr_addr=0xc0500000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860.dat Open file "/etc/Wireless/RT2860/RT2860.dat" failed! ########################################### ########################################### Read Parameters from default_profile_buffer ########################################### ########################################### cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is efuse and the information is too less to bring up the interface Force to use Flash mode NVM is FLASH mode (pAd->flash_offset = 0x40000) get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1 xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Linux video capture interface: v2.00 usbcore: registered new interface driver uvcvideo USB Video Class driver (v0.1.0) mt_msdc_init: !!!!! SDXC Module Initialize Fail !!!!! GACT probability on Mirror/redirect action on Simple TC action Loaded netem: version 1.2 u32 classifier Performance counters on input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1767 buckets, 7068 max) matchsize=264 xt_time: kernel timezone is -0000 GRE over IPv4 demultiplexor driver gre: can't add protocol ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 L2TP core driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> Warning: unable to open an initial console. Freeing unused kernel memory: 9636k freed Algorithmics/MIPS FPU Emulator v1.5 # # ###### ##### # #### ## # # # # # # # # ##### # # #### # # # # # # # # ## # # # # # # # ###### # # #### # # ####### ##### ##### ##### # # ###### # # # # # # # # # # ## # # # # # # # # # # # # # # # # # # # # # # ##### ##### ##### ##### # # # ###### # # # # # # # # # # ####### # # # # # # # # # # # # # # ## ## # ####### ##### ##### ##### # # # For further information check: http://www.netiskorea.com led=14, on=4000, off=1, blinks=1, reset=1, time=1 led=10, on=10, off=10, blinks=4000, reset=1, time=4000 led=6, on=1, off=4000, blinks=1, reset=1, time=1 led=16, on=1, off=4000, blinks=1, reset=1, time=1 led=0, on=1, off=4000, blinks=1, reset=1, time=1 tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel. Disabling lock debugging due to kernel taint Tuxera NTFS driver 3015.1.29.1 [Flags: R/W MODULE]. usbcore: registered new interface driver usblp build time = 20141115060606a rom patch for E3 IC platform = ALPS hw/sw version = ▒▒ patch version = FW Version:0.0.00 Build:1 Build Time:201411280941____ fw for E3 IC RX[0] DESC a4db0000 size = 4096 RX[1] DESC a4db1000 size = 4096 E2pAccessMode=2 cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key3Str is Invalid key length(0) or Type(1) Key4Str is Invalid key length(0) or Type(1) 1. Phy Mode = 14 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2840 assert (ad->TxPower[choffset].Channel == 42)failed Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0x0, ALNAGain2=0x0 2. Phy Mode = 14 3. Phy Mode = 14 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 r-cal result = 0 mt76x2_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=7, HT-CentCh=9, VHT-CentCh=0 APStartUp(): AP Set CentralFreq at 9(Prim=7, HT-CentCh=9, VHT-CentCh=0, BBP_BW=1) mt76x2_calibration(channel = 9) Main bssid = 04:8d:38:b4:98:20 mt76x2_reinit_agc_gain:original agc_vga0 = 0x44, agc_vga1 = 0x44 mt76x2_reinit_agc_gain:updated agc_vga0 = 0x44, agc_vga1 = 0x44 mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33 original vga value(chain0) = 44 original vga value(chain1) = 44 <==== rt28xx_init, Status=0 get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=apcli RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! build time = 20141115060606a rom patch for E3 IC platform = ALPS hw/sw version = ▒▒ patch version = FW Version:0.0.00 Build:1 Build Time:201411280941____ fw for E3 IC RX[0] DESC a5358000 size = 4096 RX[1] DESC a5359000 size = 4096 E2pAccessMode=2 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key3Str is Invalid key length(0) or Type(1) Key4Str is Invalid key length(0) or Type(1) 1. Phy Mode = 49 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2840 assert (ad->TxPower[choffset].Channel == 42)failed Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0x0, ALNAGain0=0xffffff8b, ALNAGain1=0xffffff8a, ALNAGain2=0xffffff8b 2. Phy Mode = 49 3. Phy Mode = 49 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 r-cal result = 0 mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155 APStartUp(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) mt76x2_calibration(channel = 155) Main bssid = 04:8d:38:b4:98:28 mt76x2_reinit_agc_gain:original agc_vga0 = 0x4a, agc_vga1 = 0x4a mt76x2_reinit_agc_gain:updated agc_vga0 = 0x4a, agc_vga1 = 0x4a mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x32, hi_lna1 = 0x32 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x32, hi_lna1 = 0x32 original vga value(chain0) = 4a original vga value(chain1) = 4a <==== rt28xx_init, Status=0 get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! Raeth v3.1 (Tasklet) phy_free_head is 0x4604000!!! phy_free_tail_phy is 0x4605ff0!!! txd_pool=a4606000 phy_txd_pool=04606000 ei_local->skb_free start address is 0x87d31494. free_txd: a4606010, ei_local->cpu_ptr: 04606000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa4606000 0x04606000 0x04606000 phy_qrx_ring = 0x04600000, qrx_ring = 0xa4600000 phy_rx_ring0 = 0x04608000, rx_ring0 = 0xa4608000 change HW-TRAP to 0x17c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000048d GMAC1_MAC_ADRL -- : 0x38b4981e GDMA2_MAC_ADRH -- : 0x0000048d GDMA2_MAC_ADRL -- : 0x38b4981f eth3: ===> VirtualIF_open MT7621 GE2 link rate to 10M/1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 eth3: ===> VirtualIF_open ESW: Link Status Changed - Port4 Link UP ESW: Link Status Changed - Port3 Link UP device ra0 entered promiscuous mode device eth2 entered promiscuous mode device rai0 entered promiscuous mode nf_nat_ftp: kernel >= 2.6.10 only uses 'ports' for conntrack modules Jan 1 00:00:34 miniupnpd[5861]: [truncated] m Jan 1 00:00:34 miniupnpd[5872]: [truncated] m Jan 1 00:00:34 miniupnpd[5861]: Failed to add multicast membership for interface 192.168.1.1 Jan 1 00:00:34 miniupnpd[5872]: Failed to add multicast membership for interface 192.168.1.1 Jan 1 00:00:34 miniupnpd[5861]: [truncated] m Jan 1 00:00:34 miniupnpd[5872]: [truncated] m Jan 1 00:00:34 miniupnpd[5861]: Failed to open sockets for sending SSDP notify messages. EXITING Jan 1 00:00:34 miniupnpd[5872]: Failed to open sockets for sending SSDP notify messages. EXITING ESW: Link Status Changed - Port3 Link Down br0: port 3(rai0) entering learning state br0: port 3(rai0) entering learning state br0: port 2(eth2) entering learning state br0: port 2(eth2) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state br0: port 3(rai0) entering forwarding state br0: port 2(eth2) entering forwarding state br0: port 1(ra0) entering forwarding state ESW: Link Status Changed - Port3 Link UP nf_nat_ftp: kernel >= 2.6.10 only uses 'ports' for conntrack modules br0: port 3(rai0) entering forwarding state br0: port 2(eth2) entering forwarding state br0: port 1(ra0) entering forwarding state br0: port 3(rai0) entering learning state br0: port 3(rai0) entering learning state br0: port 2(eth2) entering learning state br0: port 2(eth2) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state Ralink HW NAT Module Enabled br0: port 3(rai0) entering forwarding state br0: port 2(eth2) entering forwarding state br0: port 1(ra0) entering forwarding state ESW: Link Status Changed - Port3 Link Down nf_nat_ftp: kernel >= 2.6.10 only uses 'ports' for conntrack modules ADDRCONF(NETDEV_UP): imq0: link is not ready ADDRCONF(NETDEV_UP): imq1: link is not ready ADDRCONF(NETDEV_UP): teql0: link is not ready ADDRCONF(NETDEV_UP): sit0: link is not ready ADDRCONF(NETDEV_UP): ip6tnl0: link is not ready ADDRCONF(NETDEV_UP): apcli0: link is not ready ADDRCONF(NETDEV_UP): apclii0: link is not ready Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. br0: port 3(rai0) entering forwarding state br0: port 2(eth2) entering forwarding state br0: port 1(ra0) entering forwarding state br0: port 3(rai0) entering learning state br0: port 3(rai0) entering learning state br0: port 2(eth2) entering learning state br0: port 2(eth2) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state br0: port 3(rai0) entering forwarding state br0: port 2(eth2) entering forwarding state br0: port 1(ra0) entering forwarding state Ralink HW NAT Module Disabled Ralink HW NAT Module Enabled ESW: Link Status Changed - Port3 Link UP nf_nat_ftp: kernel >= 2.6.10 only uses 'ports' for conntrack modules led=10, on=10, off=10, blinks=4000, reset=1, time=4000


OpenWrt bootlog

=================================================================== MT7621 stage1 code 10:40:45 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11000000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL4 FB_DL: 0x8, 1/0 = 538/486 21000000 PLL3 FB_DL: 0xd, 1/0 = 633/391 35000000 PLL2 FB_DL: 0xf, 1/0 = 624/400 3D000000 do DDR setting..[00320381] Apply DDR3 Setting...(use default AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 opt_dle value:11 DRAMC_R0DELDLY[018]=00001F20 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 9 13 13 11 11 11 10 8 10 10 | 11 11 10 13 10 12 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =32 DQS1 = 31 ================================================================== bit DQS0 bit DQS1 0 (1~61)31 8 (1~60)30 1 (1~59)30 9 (1~59)30 2 (1~62)31 10 (1~62)31 3 (1~63)32 11 (1~60)30 4 (1~63)32 12 (1~62)31 5 (1~63)32 13 (1~60)30 6 (1~61)31 14 (1~62)31 7 (1~64)32 15 (1~62)31 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 14 11 14 13 11 11 12 10 9 11 10 | 11 12 10 14 10 12 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0082 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0080 DQ loop=13, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=13, finish count=2 byte:0, (DQS,DQ)=(9,8) byte:1, (DQS,DQ)=(8,8) 20,data:89 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Mar 13 2015 - 13:09:18) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb0000 Config XHCI 40M PLL Allocate 16 byte aligned buffer: 87fe1c30 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 1D C2] Device found in MTK table, ID: c2f1, EXT_ID: 801dc2 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ..============================================ Ralink UBoot Version: 4.2.0.6 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Mar 13 2015 Time:13:09:18 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN LLLLW Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bfd40000 ... Image Name: MIPS OpenWrt Linux-3.18.23 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1442425 Bytes = 1.4 MB Load Address: 80001000 Entry Point: 80001000 ...................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 128 Starting kernel ... [ 0.000000] Linux version 3.18.23 (woody@woody) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r47603) ) #2 SMP Mon Nov 23 21:43:47 KST 2015 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is NETIS WF-2881 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff] [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 9 pages/cpu @8110a000 s5824 r8192 d22848 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=000044b0 [ 0.000000] Readback ErrCtl register=000044b0 [ 0.000000] Memory: 125108K/131072K available (3302K kernel code, 172K rwdata, 636K rodata, 228K init, 252K bss, 5964K reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:256 [ 0.000000] gic: revision 3.0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] Calibrating delay loop... 577.53 BogoMIPS (lpj=2887680) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.090000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.090000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.090000] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.180000] Synchronize counters for CPU 1: done. [ 0.190000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.190000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.190000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.200000] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.290000] Synchronize counters for CPU 2: done. [ 0.300000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.300000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.300000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.300000] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.390000] Synchronize counters for CPU 3: done. [ 0.400000] Brought up 4 CPUs [ 0.410000] pinctrl core: initialized pinctrl subsystem [ 0.420000] NET: Registered protocol family 16 [ 0.430000] pull PCIe RST: RALINK_RSTCTRL = 0 [ 0.730000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.740000] ***** Xtal 40MHz ***** [ 0.740000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.750000] Port 0 N_FTS = 1b102800 [ 0.750000] Port 1 N_FTS = 1b102800 [ 0.760000] Port 2 N_FTS = 1b102800 [ 1.890000] PCIE2 no card, disable it(RST&CLK) [ 1.900000] -> 21007f2 [ 1.900000] PCIE0 enabled [ 1.910000] PCIE1 enabled [ 1.910000] PCI host bridge /pcie@1e140000 ranges: [ 1.920000] MEM 0x0000000060000000..0x000000006fffffff [ 1.930000] IO 0x000000001e160000..0x000000001e16ffff [ 1.970000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.980000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.990000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 2.000000] PCI host bridge to bus 0000:00 [ 2.000000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 2.010000] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 2.020000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 2.030000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.040000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.050000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 2.060000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.070000] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 2.080000] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 2.090000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 2.100000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 2.110000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 2.120000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 2.130000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 2.140000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 2.150000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 2.160000] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] [ 2.170000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.170000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.180000] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 2.190000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] [ 2.200000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref] [ 2.210000] pci 0000:00:01.0: PCI bridge to [bus 02] [ 2.210000] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 2.220000] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 2.230000] BAR0 at slot 0 = 0 [ 2.230000] bus=0x0, slot = 0x0 [ 2.240000] BAR0 at slot 1 = 0 [ 2.240000] bus=0x0, slot = 0x1 [ 2.250000] bus=0x1, slot = 0x0, irq=0xff [ 2.250000] bus=0x2, slot = 0x1, irq=0xff [ 2.260000] Switched to clocksource MIPS [ 2.270000] NET: Registered protocol family 2 [ 2.270000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 2.290000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 2.300000] TCP: Hash tables configured (established 1024 bind 1024) [ 2.310000] TCP: reno registered [ 2.320000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.330000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.340000] NET: Registered protocol family 1 [ 2.350000] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 2.370000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.390000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.410000] msgmni has been set to 244 [ 2.410000] io scheduler noop registered [ 2.420000] io scheduler deadline registered (default) [ 2.430000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.450000] console [ttyS0] disabled [ 2.450000] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 34, base_baud = 3125000) is a 16550A [ 2.470000] console [ttyS0] enabled [ 2.470000] console [ttyS0] enabled [ 2.490000] bootconsole [early0] disabled [ 2.490000] bootconsole [early0] disabled [ 2.500000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 2.520000] Allocate 16 byte aligned buffer: 804743b0 [ 2.530000] Enable NFI Clock [ 2.530000] # MTK NAND # : Use HW ECC [ 2.540000] Device found in MTK table, ID: c2f1, EXT_ID: 801dc2 [ 2.550000] Support this Device in MTK table! c2f1 [ 2.560000] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 2.570000] nand: Macronix NAND 128MiB 3,3V 8-bit [ 2.580000] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 2.590000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 [ 2.610000] Scanning device for bad blocks [ 2.890000] 7 ofpart partitions found on MTD device MT7621-NAND [ 2.900000] Creating 7 MTD partitions on "MT7621-NAND": [ 2.910000] 0x000000000000-0x000000030000 : "u-boot" [ 2.920000] 0x000000080000-0x000000100000 : "config" [ 2.930000] 0x000000100000-0x000000140000 : "factory" [ 2.940000] 0x000000140000-0x000000340000 : "kernel" [ 2.950000] 0x000000030000-0x000000031000 : "u-boot-env" [ 2.960000] 0x000000140000-0x000007000000 : "firmware" [ 5.000000] 0x000000340000-0x000007000000 : "ubi" [ 5.010000] [mtk_nand] probe successfully! [ 5.020000] Signature matched and data read! [ 5.030000] load_fact_bbt success 1023 [ 5.040000] netif_napi_add() called with weight 128 on device eth%d [ 5.060000] change HW-TRAP to 0x17ccf [ 5.070000] libphy: mdio: probed [ 5.090000] ralink_soc_eth 1e100000.ethernet: loaded mt7530 driver [ 5.100000] ralink_soc_eth 1e100000.ethernet eth0: ralink at 0xbe100000, irq 11 [ 5.120000] mt7621_wdt 1e000100.wdt: Initialized [ 5.130000] TCP: cubic registered [ 5.130000] NET: Registered protocol family 10 [ 5.140000] NET: Registered protocol family 17 [ 5.150000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 5.180000] 8021q: 802.1Q VLAN Support v1.8 [ 5.190000] UBI: auto-attach mtd6 [ 5.200000] UBI: attaching mtd6 to ubi0 [ 6.220000] UBI: scanning is finished [ 6.240000] UBI: attached mtd6 (name "ubi", size 108 MiB) to ubi0 [ 6.260000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 6.270000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 6.280000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 6.300000] UBI: good PEBs: 870, bad PEBs: 0, corrupted PEBs: 0 [ 6.310000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 6.320000] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1578198545 [ 6.340000] UBI: available PEBs: 0, total reserved PEBs: 870, PEBs reserved for bad PEB handling: 20 [ 6.360000] UBI: background thread "ubi_bgt0d" started, PID 294 [ 6.360000] UBI: ubiblock0_0 created from ubi0:0(rootfs) [ 6.360000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 6.360000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 6.410000] UBIFS error (pid 1): init_constants_early: too few LEBs (16), min. is 17 [ 6.430000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 6.440000] Freeing unused kernel memory: 228K (80407000 - 80440000) [ 7.230000] init: Console is alive [ 7.240000] init: - watchdog - [ 7.820000] usbcore: registered new interface driver usbfs [ 7.840000] usbcore: registered new interface driver hub [ 7.850000] usbcore: registered new device driver usb [ 7.880000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.900000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.920000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.940000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.960000] FM_OUT value: u4FmOut = 0(0x00000000) [ 7.980000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.000000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.020000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.040000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.060000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.070000] ralink_soc_eth 1e100000.ethernet eth0: port 4 link up [ 8.130000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.150000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.170000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.190000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.210000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.230000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.250000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.270000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.290000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.310000] FM_OUT value: u4FmOut = 0(0x00000000) [ 8.460000] xhci-hcd xhci-hcd: xHCI Host Controller [ 8.470000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 [ 8.480000] xhci-hcd xhci-hcd: irq 30, io mem 0x1e1c0000 [ 8.490000] hub 1-0:1.0: USB hub found [ 8.500000] hub 1-0:1.0: 2 ports detected [ 8.510000] xhci-hcd xhci-hcd: xHCI Host Controller [ 8.520000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 [ 8.530000] hub 2-0:1.0: USB hub found [ 8.540000] hub 2-0:1.0: 1 port detected [ 9.250000] init: - preinit - [ 9.610000] random: procd urandom read with 123 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.170000] random: nonblocking pool is initialized [ 12.700000] UBIFS: background thread "ubifs_bgt0_1" started, PID 368 [ 12.770000] UBIFS: recovery needed [ 13.560000] UBIFS: recovery completed [ 13.560000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 13.580000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 13.590000] UBIFS: FS size: 103993344 bytes (99 MiB, 819 LEBs), journal size 5206016 bytes (4 MiB, 41 LEBs) [ 13.610000] UBIFS: reserved for root: 4911862 bytes (4796 KiB) [ 13.630000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E0252E0D-8BBF-4A79-B987-6DF1923EC9B3, small LPT model [ 13.660000] mount_root: switching to jffs2 overlay [ 13.740000] procd: - early - [ 13.750000] procd: - watchdog - [ 14.480000] procd: - ubus - [ 15.490000] procd: - init - Please press Enter to activate this console. [ 16.010000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 16.020000] Loading modules backported from Linux version master-2015-10-26-0-g28c26cb [ 16.040000] Backport generated by backports.git backports-20150903-4-g12cf266 [ 16.070000] cfg80211: World regulatory domain updated: [ 16.080000] cfg80211: DFS Master region: unset [ 16.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 16.110000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 16.120000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 16.140000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 16.150000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 16.170000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 16.190000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 16.210000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 16.220000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 16.240000] mt76pci 0000:01:00.0: ASIC revision: 76120044 [ 16.270000] ROM patch build: 20141115060606a [ 16.280000] Firmware Version: 0.0.00 [ 16.290000] Build: 1 [ 16.290000] Build Time: 201410061140____ [ 16.320000] Firmware running! [ 16.320000] mt76pci 0000:02:00.0: ASIC revision: 76020044 [ 16.360000] ROM patch already applied [ 16.360000] Firmware Version: 0.0.00 [ 16.370000] Build: 1 [ 16.380000] Build Time: 201410061140____ [ 16.410000] Firmware running! [ 16.420000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.440000] nf_conntrack version 0.5.0 (1958 buckets, 7832 max) [ 16.550000] xt_time: kernel timezone is -0000 [ 16.560000] PPP generic driver version 2.4.2 [ 16.570000] NET: Registered protocol family 24 [ 20.340000] device eth0.1 entered promiscuous mode [ 20.350000] device eth0 entered promiscuous mode [ 20.360000] br-lan: port 1(eth0.1) entered forwarding state [ 20.380000] br-lan: port 1(eth0.1) entered forwarding state [ 22.380000] br-lan: port 1(eth0.1) entered forwarding state BusyBox v1.24.1 (2015-11-23 21:08:53 KST) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- DESIGNATED DRIVER (Bleeding Edge, r47603) ----------------------------------------------------- * 2 oz. Orange Juice Combine all juices in a * 2 oz. Pineapple Juice tall glass filled with * 2 oz. Grapefruit Juice ice, stir well. * 2 oz. Cranberry Juice ----------------------------------------------------- root@OpenWrt:/#


Tags

toh/netis/wf-2881.txt · Last modified: 2017/05/30 12:29 by tmomas