Olimex A10-OLinuXino-LIME

For further Allwinner-based boards, please refer to soc.allwinner.sunxi

Hardware highlights

Model Ports
Cubieboard μSD, 2x USB2, 10/100 Mbps ethernet, SATA, UEXT, HDMI

Serial

You can use your usual serial levelshifter. Pinout is:

[ HDMI ]                          [ USB ]

                             [ ethernet ]
[ μSD ]                       o  o  o
                             TX RX GND

Status

Installation process

Please refer to soc.allwinner.sunxi.

dmesg

U-Boot SPL 2014.04 (Sep 28 2014 - 17:49:15)                                     
Board: A10-OLinuXino-Lime                                                       
DRAM: 512 MiB                                                                   
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2                                           
spl: not an uImage at 1600                                                      
                                                                                
                                                                                
U-Boot 2014.04 (Sep 28 2014 - 17:49:15) Allwinner Technology                    
                                                                                
CPU:   Allwinner A10 (SUN4I)                                                    
Board: A10-OLinuXino-Lime                                                       
I2C:   ready                                                                    
DRAM:  512 MiB                                                                  
MMC:   SUNXI SD/MMC: 0                                                          
*** Warning - bad CRC, using default environment                                
                                                                                
In:    serial                                                                   
Out:   serial                                                                   
Err:   serial                                                                   
Net:   emac                                                                     
Hit any key to stop autoboot:  0                                                
reading uEnv.txt                                                                
240 bytes read in 17 ms (13.7 KiB/s)                                            
Loaded environment from uEnv.txt                                                
Running uenvcmd ...                                                             
reading uImage                                                                  
2574432 bytes read in 345 ms (7.1 MiB/s)                                        
reading dtb                                                                     
17570 bytes read in 28 ms (612.3 KiB/s)                                         
## Booting kernel from Legacy Image at 46000000 ...                             
   Image Name:   ARM OpenWrt Linux-3.14.18                                      
   Image Type:   ARM Linux Kernel Image (uncompressed)                          
   Data Size:    2574368 Bytes = 2.5 MiB                                        
   Load Address: 40008000                                                       
   Entry Point:  40008000                                                       
   Verifying Checksum ... OK                                                    
## Flattened Device Tree blob at 49000000                                       
   Booting using the fdt blob at 0x49000000                                     
   Loading Kernel Image ... OK                                                  
   Using Device Tree in place at 49000000, end 490074a1                         
                                                                                
Starting kernel ...                                                             
                                                                                
[    0.000000] Booting Linux on physical CPU 0x0                                
[    0.000000] Linux version 3.14.18 (wigyori@trabant) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42689) ) #1 SMP PREEMPT Sun Sep 28 17:52:26 CEST 2014
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d  
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Olimex A10-OLinuXino-LIME                         
[    0.000000] Memory policy: Data cache writeback                              
[    0.000000] CPU: All CPU(s) started in SVC mode.                             
[    0.000000] PERCPU: Embedded 7 pages/cpu @dfbe8000 s7104 r8192 d13376 u32768 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)              
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)  
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)   
[    0.000000] Memory: 514040K/524288K available (3647K kernel code, 163K rwdata, 1028K rodata, 190K init, 603K bss, 10248K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:                                    
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)                
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)                
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)                
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)                
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)                
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)                
[    0.000000]       .text : 0xc0008000 - 0xc0498f04   (4676 kB)                
[    0.000000]       .init : 0xc0499000 - 0xc04c8bc0   ( 191 kB)                
[    0.000000]       .data : 0xc04ca000 - 0xc04f2f60   ( 164 kB)                
[    0.000000]        .bss : 0xc04f2f60 - 0xc0589b9c   ( 604 kB)                
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1       
[    0.000000] Preemptible hierarchical RCU implementation.                     
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.            
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1     
[    0.000000] NR_IRQS:16 nr_irqs:16 16                                         
[    0.000016] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[    0.000238] Console: colour dummy device 80x30                               
[    0.000264] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)         
[    0.090083] pid_max: default: 32768 minimum: 301                             
[    0.090207] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)      
[    0.090219] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 
[    0.094290] CPU: Testing write buffer coherency: ok                          
[    0.094566] CPU0: thread -1, cpu 0, socket -1, mpidr 0                       
[    0.094616] Setting up static identity map for 0x40011988 - 0x400119bc       
[    0.130238] Brought up 1 CPUs                                                
[    0.130250] SMP: Total of 1 processors activated.                            
[    0.130258] CPU: All CPU(s) started in SVC mode.                             
[    0.131099] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    0.131311] pinctrl core: initialized pinctrl subsystem                      
[    0.131661] regulator-dummy: no parameters                                   
[    0.131914] NET: Registered protocol family 16                               
[    0.132346] DMA: preallocated 256 KiB pool for atomic coherent allocations   
[    0.140042] bio: create slab <bio-0> at 0                                    
[    0.140653] reg-fixed-voltage ahci-5v.1: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@1, deferring probe
[    0.140676] platform ahci-5v.1: Driver reg-fixed-voltage requests probe deferral
[    0.140703] reg-fixed-voltage usb1-vbus.2: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[    0.140717] platform usb1-vbus.2: Driver reg-fixed-voltage requests probe deferral
[    0.140740] reg-fixed-voltage usb2-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[    0.140754] platform usb2-vbus.3: Driver reg-fixed-voltage requests probe deferral
[    0.141136] SCSI subsystem initialized                                       
[    0.141597] usbcore: registered new interface driver usbfs                   
[    0.141660] usbcore: registered new interface driver hub                     
[    0.141774] usbcore: registered new device driver usb                        
[    0.141900] pps_core: LinuxPPS API ver. 1 registered                         
[    0.141908] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.141936] PTP clock support registered                                     
[    0.142744] Switched to clocksource timer                                    
[    0.149141] NET: Registered protocol family 2                                
[    0.149963] TCP established hash table entries: 4096 (order: 2, 16384 bytes) 
[    0.150016] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)        
[    0.150178] TCP: Hash tables configured (established 4096 bind 4096)         
[    0.150246] TCP: reno registered                                             
[    0.150262] UDP hash table entries: 256 (order: 1, 8192 bytes)               
[    0.150283] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)          
[    0.150495] NET: Registered protocol family 1                                
[    0.151547] futex hash table entries: 256 (order: 2, 16384 bytes)            
[    0.151597] audit: initializing netlink subsys (disabled)                    
[    0.151649] audit: type=2000 audit(0.140:1): initialized                     
[    0.159760] VFS: Disk quotas dquot_6.5.2                                     
[    0.160035] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)       
[    0.161811] squashfs: version 4.0 (2009/01/31) Phillip Lougher               
[    0.161824] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.162553] msgmni has been set to 1003                                      
[    0.164555] io scheduler noop registered                                     
[    0.164570] io scheduler deadline registered                                 
[    0.164610] io scheduler cfq registered (default)                            
[    0.164852] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral
[    0.166958] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver      
[    0.207659] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled         
[    0.229794] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 27, base_baud = 1500000) is a U6_16550A
[    0.754232] console [ttyS0] enabled                                          
[    0.758409] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral 
[    0.766391] 1c0b080.mdio supply phy not found, using dummy regulator         
[    0.772919] libphy: sun4i_mii_bus: probed                                    
[    0.813408] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver       
[    0.819934] ehci-platform: EHCI generic platform driver                      
[    0.825331] platform 1c14000.usb: Driver ehci-platform requests probe deferral
[    0.832605] platform 1c1c000.usb: Driver ehci-platform requests probe deferral
[    0.839937] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver           
[    0.846169] ohci-platform: OHCI generic platform driver                      
[    0.851481] platform 1c14400.usb: Driver ohci-platform requests probe deferral
[    0.858799] platform 1c1c400.usb: Driver ohci-platform requests probe deferral
[    0.866169] usbcore: registered new interface driver usb-storage             
[    0.872387] mousedev: PS/2 mouse device common for all mice                  
[    0.886677] input: axp20x-pek as /devices/soc.0/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[    0.896295] LDO1: 1300 mV                                                    
[    0.899675] LDO2: 1800 <--> 3300 mV at 3000 mV                               
[    0.904682] LDO3: 700 <--> 3500 mV at 2275 mV                                
[    0.909309] LDO4: 1250 <--> 3300 mV at 2800 mV                               
[    0.914287] LDO5: 1800 <--> 3300 mV at 2800 mV                               
[    0.919227] DCDC2: 700 <--> 2275 mV at 1400 mV                               
[    0.924447] DCDC3: 700 <--> 3500 mV at 1250 mV                               
[    0.929082] axp20x 0-0034: AXP20X driver loaded                              
[    0.934142] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    0.942858] sunxi-mmc 1c0f000.mmc: Got CD GPIO #225.                         
[    0.947996] sunxi-mmc 1c0f000.mmc: base:0xe08e4000 irq:18                    
[    0.954195] TCP: cubic registered                                            
[    0.957512] Initializing XFRM netlink socket                                 
[    0.961799] NET: Registered protocol family 17                               
[    0.966383] 8021q: 802.1Q VLAN Support v1.8                                  
[    0.970658] Registering SWP/SWPB emulation handler                           
[    0.975809] registered taskstats version 1                                   
[    0.980183] regulator-dummy: disabling                                       
[    0.984613] ahci-5v: 5000 mV                                                 
[    0.987927] usb1-vbus: 5000 mV                                               
[    0.991377] usb2-vbus: 5000 mV                                               
[    1.062782] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    1.070268] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1               
[    1.076165] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    1.085134] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[    1.094089] scsi0 : ahci_platform                                            
[    1.097732] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 21
[    1.106992] ehci-platform 1c14000.usb: EHCI Host Controller                  
[    1.113761] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[    1.121613] ehci-platform 1c14000.usb: irq 19, io mem 0x01c14000             
[    1.142754] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00            
[    1.149023] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002    
[    1.155826] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.163056] usb usb1: Product: EHCI Host Controller                          
[    1.167929] usb usb1: Manufacturer: Linux 3.14.18 ehci_hcd                   
[    1.174438] usb usb1: SerialNumber: 1c14000.usb                              
[    1.179458] hub 1-0:1.0: USB hub found                                       
[    1.183289] hub 1-0:1.0: 1 port detected                                     
[    1.187737] ehci-platform 1c1c000.usb: EHCI Host Controller                  
[    1.193389] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[    1.201273] ehci-platform 1c1c000.usb: irq 22, io mem 0x01c1c000             
[    1.222760] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00            
[    1.229012] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002    
[    1.235814] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.243043] usb usb2: Product: EHCI Host Controller                          
[    1.247916] usb usb2: Manufacturer: Linux 3.14.18 ehci_hcd                   
[    1.253409] usb usb2: SerialNumber: 1c1c000.usb                              
[    1.258386] hub 2-0:1.0: USB hub found                                       
[    1.262165] hub 2-0:1.0: 1 port detected                                     
[    1.268636] ohci-platform 1c14400.usb: Generic Platform OHCI controller      
[    1.275293] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[    1.283788] ohci-platform 1c14400.usb: irq 20, io mem 0x01c14400             
[    1.347075] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001    
[    1.353912] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.361143] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.370340] usb usb3: Product: Generic Platform OHCI controller              
[    1.376295] usb usb3: Manufacturer: Linux 3.14.18 ohci_hcd                   
[    1.381809] usb usb3: SerialNumber: 1c14400.usb                              
[    1.386853] hub 3-0:1.0: USB hub found                                       
[    1.390632] hub 3-0:1.0: 1 port detected                                     
[    1.395074] ohci-platform 1c1c400.usb: Generic Platform OHCI controller      
[    1.401704] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[    1.409592] ohci-platform 1c1c400.usb: irq 23, io mem 0x01c1c400             
[    1.462765] ata1: SATA link down (SStatus 0 SControl 300)                    
[    1.476885] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001    
[    1.483714] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.490930] usb usb4: Product: Generic Platform OHCI controller              
[    1.497046] usb usb4: Manufacturer: Linux 3.14.18 ohci_hcd                   
[    1.502529] usb usb4: SerialNumber: 1c1c400.usb                              
[    1.507561] hub 4-0:1.0: USB hub found                                       
[    1.511345] hub 4-0:1.0: 1 port detected                                     
[    1.515656] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)          
[    1.527301] Waiting for root device /dev/mmcblk0p2...                        
[    1.552051] mmc0: new high speed SDHC card at address 1234                   
[    1.558072] mmcblk0: mmc0:1234 SA04G 3.67 GiB                                
[    1.563964]  mmcblk0: p1 p2                                                  
[    1.634130] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.642972] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.655549] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    1.663257] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.    
[    1.670256] Freeing unused kernel memory: 188K (c0499000 - c04c8000)         
procd: Console is alive                                                         
procd: - watchdog -                                                             
procd: - preinit -                                                              
probing /dev/mmcblk0 for uboot env data                                         
Detected generic sunxi // generic sunxi                                         
[    1.980664] random: mktemp urandom read with 18 bits of entropy available    
Press the [f] key and hit [enter] to enter failsafe mode                        
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level    
mounting /dev/root                                                              
[    5.043349] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)                    
procd: - early -                                                                
procd: - watchdog -                                                             
procd: - ubus -                                                                 
procd: - init -                                                                 
Please press Enter to activate this console.                                    
[    7.434227] NET: Registered protocol family 10                               
[    7.452955] ip6_tables: (C) 2000-2006 Netfilter Core Team                    
[    7.474880] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0    
[    7.481676] sunxi-rtc 1c20d00.rtc: RTC enabled                               
[    7.519630] ip_tables: (C) 2000-2006 Netfilter Core Team                     
[    7.552156] nf_conntrack version 0.5.0 (8034 buckets, 32136 max)             
[    7.607716] sun4i-emac 1c0b000.ethernet: eth0: at e09d8000, IRQ 17 MAC: 02:14:02:81:8f:e4
[    7.653598] xt_time: kernel timezone is -0000                                
[    7.675298] PPP generic driver version 2.4.2                                 
[    7.682924] NET: Registered protocol family 24                               
[   11.203097] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready               
[   11.209206] device eth0 entered promiscuous mode                             
[   11.263123] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready             
procd: - init complete -                                                        
[   13.362775] libphy: 1c0b080.mdio-mii:01 - Link is Up - 100/Full              
[   13.368738] br-lan: port 1(eth0) entered forwarding state                    
[   13.374199] br-lan: port 1(eth0) entered forwarding state                    
[   13.380121] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready          
[   13.386711] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready        
[   14.877711] random: nonblocking pool is initialized                          
[   15.372748] br-lan: port 1(eth0) entered forwarding state                    
                                                                                
                                                                                
                                                                                
BusyBox v1.22.1 (2014-09-28 17:49:16 CEST) built-in shell (ash)                 
Enter 'help' for a list of built-in commands.                                   
                                                                                
  _______                     ________        __                                
 |       |.-----.-----.-----.|  |  |  |.----.|  |_                              
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|                             
 |_______||   __|_____|__|__||________||__|  |____|                             
          |__| W I R E L E S S   F R E E D O M                                  
 -----------------------------------------------------                          
 CHAOS CALMER (Bleeding Edge, r42689)                                           
 -----------------------------------------------------                          
  * 1 1/2 oz Gin            Shake with a glassful                               
  * 1/4 oz Triple Sec       of broken ice and pour                              
  * 3/4 oz Lime Juice       unstrained into a goblet.                           
  * 1 1/2 oz Orange Juice                                                       
  * 1 tsp. Grenadine Syrup                                                      
 -----------------------------------------------------                          
root@OpenWrt:/# 

Tags

Back to top

toh/olimex/a10-olinuxino.txt · Last modified: 2014/09/28 18:22 by wigyori