pcDuino v3

For further Allwinner-based boards, please refer to soc.allwinner.sunxi

Hardware highlights

Model Ports
pcDuino3 1x USB, 1x RTL8188EUS, 1x 10/100 ethernet, MMC, SATA, 4GB NAND, UEXT, HDMI, sound, Arduino-compatible headers

Availability

The board is available from various vendors, including the manufacturer itself, see here for pcDuino v3.

Further details on the board: http://linux-sunxi.org/LinkSprite_pcDuino_V3

Serial

You can use your usual serial levelshifter. Pinout is:

TBD

Status

Installation process

Please refer to soc.allwinner.sunxi.

dmesg

U-Boot SPL 2014.04 (Sep 28 2014 - 18:38:40)                                     
Board: Linksprite_pcDuino3                                                      
DRAM: 1024 MiB                                                                  
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2                                            
spl: not an uImage at 1600                                                      
                                                                                
                                                                                
U-Boot 2014.04 (Sep 28 2014 - 18:38:40) Allwinner Technology                    
                                                                                
CPU:   Allwinner A20 (SUN7I)                                                    
Board: Linksprite_pcDuino3                                                      
I2C:   ready                                                                    
DRAM:  1 GiB                                                                    
MMC:   SUNXI SD/MMC: 0                                                          
*** Warning - bad CRC, using default environment                                
                                                                                
In:    serial                                                                   
Out:   serial                                                                   
Err:   serial                                                                   
Net:   dwmac.1c50000                                                            
Hit any key to stop autoboot:  0                                                
reading uEnv.txt                                                                
240 bytes read in 16 ms (14.6 KiB/s)                                            
Loaded environment from uEnv.txt                                                
Running uenvcmd ...                                                             
reading uImage                                                                  
2574728 bytes read in 296 ms (8.3 MiB/s)                                        
reading dtb                                                                     
22361 bytes read in 28 ms (779.3 KiB/s)                                         
## Booting kernel from Legacy Image at 46000000 ...                             
   Image Name:   ARM OpenWrt Linux-3.14.18                                      
   Image Type:   ARM Linux Kernel Image (uncompressed)                          
   Data Size:    2574664 Bytes = 2.5 MiB                                        
   Load Address: 40008000                                                       
   Entry Point:  40008000                                                       
   Verifying Checksum ... OK                                                    
## Flattened Device Tree blob at 49000000                                       
   Booting using the fdt blob at 0x49000000                                     
   Loading Kernel Image ... OK                                                  
   Using Device Tree in place at 49000000, end 49008758                         
                                                                                
Starting kernel ...                                                             
                                                                                
[    0.000000] Booting Linux on physical CPU 0x0                                
[    0.000000] Linux version 3.14.18 (wigyori@trabant) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42689) ) #3 SMP PREEMPT Sun Sep 28 18:39:27 CEST 2014
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d  
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: LinkSprite pcDuino V3                             
[    0.000000] Memory policy: Data cache writealloc                             
[    0.000000] psci: probing function IDs from device-tree                      
[    0.000000] PERCPU: Embedded 7 pages/cpu @eefdb000 s7104 r8192 d13376 u32768 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260624
[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)             
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) 
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)   
[    0.000000] Memory: 1033784K/1048576K available (3647K kernel code, 163K rwdata, 1028K rodata, 190K init, 603K bss, 14792K reserved, 270336K highmem)
[    0.000000] Virtual kernel memory layout:                                    
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)                
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)                
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)                
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)                
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)                
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)                
[    0.000000]       .text : 0xc0008000 - 0xc0498f04   (4676 kB)                
[    0.000000]       .init : 0xc0499000 - 0xc04c8bc0   ( 191 kB)                
[    0.000000]       .data : 0xc04ca000 - 0xc04f2f60   ( 164 kB)                
[    0.000000]        .bss : 0xc04f2f60 - 0xc0589b9c   ( 604 kB)                
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1       
[    0.000000] Preemptible hierarchical RCU implementation.                     
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.            
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2     
[    0.000000] NR_IRQS:16 nr_irqs:16 16                                         
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).            
[    0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[    0.000018] Switching to timer-based delay loop                              
[    0.000320] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[    0.000466] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
[    0.000618] Console: colour dummy device 80x30                               
[    0.000655] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000670] pid_max: default: 32768 minimum: 301                             
[    0.000835] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)      
[    0.000848] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) 
[    0.006348] CPU: Testing write buffer coherency: ok                          
[    0.006685] /cpus/cpu@0 missing clock-frequency property                     
[    0.006707] /cpus/cpu@1 missing clock-frequency property                     
[    0.006720] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000                 
[    0.006747] Setting up static identity map for 0x40011988 - 0x400119bc       
[    0.060436] CPU1: Booted secondary processor                                 
[    0.060479] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001                 
[    0.060581] Brought up 2 CPUs                                                
[    0.060602] SMP: Total of 2 processors activated.                            
[    0.060608] CPU: All CPU(s) started in HYP mode.                             
[    0.060614] CPU: Virtualization extensions available.                        
[    0.065308] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[    0.065632] pinctrl core: initialized pinctrl subsystem                      
[    0.065999] regulator-dummy: no parameters                                   
[    0.066313] NET: Registered protocol family 16                               
[    0.066575] DMA: preallocated 256 KiB pool for atomic coherent allocations   
[    0.076089] bio: create slab <bio-0> at 0                                    
[    0.076669] reg-fixed-voltage ahci-5v.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@0, deferring probe
[    0.076698] platform ahci-5v.4: Driver reg-fixed-voltage requests probe deferral
[    0.076725] reg-fixed-voltage usb1-vbus.5: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[    0.076740] platform usb1-vbus.5: Driver reg-fixed-voltage requests probe deferral
[    0.076762] reg-fixed-voltage usb2-vbus.6: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[    0.076776] platform usb2-vbus.6: Driver reg-fixed-voltage requests probe deferral
[    0.077213] SCSI subsystem initialized                                       
[    0.077704] usbcore: registered new interface driver usbfs                   
[    0.077776] usbcore: registered new interface driver hub                     
[    0.077891] usbcore: registered new device driver usb                        
[    0.078016] pps_core: LinuxPPS API ver. 1 registered                         
[    0.078025] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.078049] PTP clock support registered                                     
[    0.078924] Switched to clocksource arch_sys_counter                         
[    0.085821] NET: Registered protocol family 2                                
[    0.086883] TCP established hash table entries: 8192 (order: 3, 32768 bytes) 
[    0.086975] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)        
[    0.087098] TCP: Hash tables configured (established 8192 bind 8192)         
[    0.087175] TCP: reno registered                                             
[    0.087192] UDP hash table entries: 512 (order: 2, 16384 bytes)              
[    0.087246] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)         
[    0.087565] NET: Registered protocol family 1                                
[    0.088874] futex hash table entries: 512 (order: 3, 32768 bytes)            
[    0.089097] audit: initializing netlink subsys (disabled)                    
[    0.089165] audit: type=2000 audit(0.070:1): initialized                     
[    0.089642] bounce pool size: 64 pages                                       
[    0.097310] VFS: Disk quotas dquot_6.5.2                                     
[    0.097621] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)       
[    0.099683] squashfs: version 4.0 (2009/01/31) Phillip Lougher               
[    0.099697] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.100470] msgmni has been set to 1491                                      
[    0.102390] io scheduler noop registered                                     
[    0.102409] io scheduler deadline registered                                 
[    0.102458] io scheduler cfq registered (default)                            
[    0.102773] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral
[    0.105163] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver      
[    0.146316] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled         
[    0.168596] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[    0.755429] console [ttyS0] enabled                                          
[    0.780757] dw-apb-uart 1c29800.serial: Couldn't set LCR to 0                
[    0.787503] dw-apb-uart 1c29800.serial: Couldn't set LCR to 0                
[    0.793276] 1c29800.serial: ttyS1 at MMIO 0x1c29800 (irq = 51, base_baud = 1500000) is a U6_16550A
[    0.824249] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0                
[    0.830996] dw-apb-uart 1c29c00.serial: Couldn't set LCR to 0                
[    0.836792] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 52, base_baud = 1500000) is a U6_16550A
[    0.846615] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral 
[    0.856360] stmmaceth 1c50000.ethernet: no regulator found                   
[    0.861939] stmmaceth 1c50000.ethernet: no reset control found               
[    0.867768]  Ring mode enabled                                               
[    0.870837]  No HW DMA feature register supported                            
[    0.875362]  Normal descriptors                                              
[    0.878682]  TX Checksum insertion supported                                 
[    0.886784] libphy: stmmac: probed                                           
[    0.890220] eth0: PHY ID 02430c54 at 1 IRQ 0 (stmmac-0:01) active            
[    0.896406] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver       
[    0.902946] ehci-platform: EHCI generic platform driver                      
[    0.908343] platform 1c14000.usb: Driver ehci-platform requests probe deferral
[    0.915669] platform 1c1c000.usb: Driver ehci-platform requests probe deferral
[    0.922994] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver           
[    0.929210] ohci-platform: OHCI generic platform driver                      
[    0.934541] platform 1c14400.usb: Driver ohci-platform requests probe deferral
[    0.941858] platform 1c1c400.usb: Driver ohci-platform requests probe deferral
[    0.949231] usbcore: registered new interface driver usb-storage             
[    0.955481] mousedev: PS/2 mouse device common for all mice                  
[    0.961500] input: 1c22800.lradc as /devices/soc.3/1c22800.lradc/input/input0
[    0.977699] input: axp20x-pek as /devices/soc.3/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input1
[    0.987356] LDO1: 1300 mV                                                    
[    0.990775] LDO2: 1800 <--> 3300 mV at 3000 mV                               
[    0.995724] LDO3: 700 <--> 3500 mV at 2275 mV                                
[    1.000429] LDO4: 1250 <--> 3300 mV at 2800 mV                               
[    1.005367] LDO5: 1800 <--> 3300 mV at 2800 mV                               
[    1.010373] DCDC2: 700 <--> 2275 mV at 1400 mV                               
[    1.015562] DCDC3: 700 <--> 3500 mV at 1300 mV                               
[    1.020225] axp20x 0-0034: AXP20X driver loaded                              
[    1.025906] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.034738] sunxi-mmc 1c0f000.mmc: Got CD GPIO #225.                         
[    1.039937] sunxi-mmc 1c0f000.mmc: base:0xf00fc000 irq:64                    
[    1.047574] sunxi-ss 1c15000.crypto-engine: Die ID 0                         
[    1.054068] TCP: cubic registered                                            
[    1.057394] Initializing XFRM netlink socket                                 
[    1.061849] NET: Registered protocol family 17                               
[    1.066390] 8021q: 802.1Q VLAN Support v1.8                                  
[    1.070701] Registering SWP/SWPB emulation handler                           
[    1.075866] registered taskstats version 1                                   
[    1.080302] regulator-dummy: disabling                                       
[    1.084541] ahci-5v: 5000 mV                                                 
[    1.087926] usb1-vbus: 5000 mV                                               
[    1.091570] usb2-vbus: 5000 mV                                               
[    1.158977] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    1.166462] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1               
[    1.172364] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    1.181337] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[    1.190249] scsi0 : ahci_platform                                            
[    1.193919] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88
[    1.202282] ehci-platform 1c14000.usb: EHCI Host Controller                  
[    1.207887] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[    1.215769] ehci-platform 1c14000.usb: irq 71, io mem 0x01c14000             
[    1.238944] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00            
[    1.245230] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002    
[    1.252035] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.259262] usb usb1: Product: EHCI Host Controller                          
[    1.264137] usb usb1: Manufacturer: Linux 3.14.18 ehci_hcd                   
[    1.269637] usb usb1: SerialNumber: 1c14000.usb                              
[    1.274719] hub 1-0:1.0: USB hub found                                       
[    1.278504] hub 1-0:1.0: 1 port detected                                     
[    1.282998] ehci-platform 1c1c000.usb: EHCI Host Controller                  
[    1.288606] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[    1.296470] ehci-platform 1c1c000.usb: irq 72, io mem 0x01c1c000             
[    1.318941] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00            
[    1.325203] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002    
[    1.332007] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.339235] usb usb2: Product: EHCI Host Controller                          
[    1.344109] usb usb2: Manufacturer: Linux 3.14.18 ehci_hcd                   
[    1.349600] usb usb2: SerialNumber: 1c1c000.usb                              
[    1.354647] hub 2-0:1.0: USB hub found                                       
[    1.358430] hub 2-0:1.0: 1 port detected                                     
[    1.362890] ohci-platform 1c14400.usb: Generic Platform OHCI controller      
[    1.369553] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[    1.377376] ohci-platform 1c14400.usb: irq 96, io mem 0x01c14400             
[    1.386191] mmc0: host does not support reading read-only switch. assuming write-enable.
[    1.443094] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001    
[    1.449894] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.457110] usb usb3: Product: Generic Platform OHCI controller              
[    1.463515] usb usb3: Manufacturer: Linux 3.14.18 ohci_hcd                   
[    1.469019] usb usb3: SerialNumber: 1c14400.usb                              
[    1.474115] hub 3-0:1.0: USB hub found                                       
[    1.477899] hub 3-0:1.0: 1 port detected                                     
[    1.482500] ohci-platform 1c1c400.usb: Generic Platform OHCI controller      
[    1.489166] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[    1.497003] ohci-platform 1c1c400.usb: irq 97, io mem 0x01c1c400             
[    1.548947] ata1: SATA link down (SStatus 0 SControl 300)                    
[    1.559569] mmc0: new high speed SDHC card at address 1234                   
[    1.563091] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001    
[    1.563099] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.563104] usb usb4: Product: Generic Platform OHCI controller              
[    1.563110] usb usb4: Manufacturer: Linux 3.14.18 ohci_hcd                   
[    1.563115] usb usb4: SerialNumber: 1c1c400.usb                              
[    1.563668] hub 4-0:1.0: USB hub found                                       
[    1.563714] hub 4-0:1.0: 1 port detected                                     
[    1.598972] usb 1-1: new high-speed USB device number 2 using ehci-platform  
[    1.609590] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)          
[    1.615988] mmcblk0: mmc0:1234 SA04G 3.67 GiB                                
[    1.622142]  mmcblk0: p1 p2                                                  
[    1.627065] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.636160] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.648627] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
[    1.656199] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.    
[    1.663318] Freeing unused kernel memory: 188K (c0499000 - c04c8000)         
[    1.760088] usb 1-1: New USB device found, idVendor=0bda, idProduct=8179     
[    1.766801] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.773966] usb 1-1: Product: 802.11n NIC                                    
[    1.777979] usb 1-1: Manufacturer: Realtek                                   
[    1.782130] usb 1-1: SerialNumber: 00E04C0001                                
procd: Console is alive                                                         
procd: - watchdog -                                                             
procd: - preinit -                                                              
probing /dev/mmcblk0 for uboot env data                                         
Detected generic sunxi // generic sunxi                                         
[    1.987475] random: mktemp urandom read with 16 bits of entropy available    
Press the [f] key and hit [enter] to enter failsafe mode                        
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level    
mounting /dev/root                                                              
[    5.051065] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)                    
procd: - early -                                                                
procd: - watchdog -                                                             
procd: - ubus -                                                                 
procd: - init -                                                                 
Please press Enter to activate this console.                                    
[    6.401548] NET: Registered protocol family 10                               
[    6.413166] ip6_tables: (C) 2000-2006 Netfilter Core Team                    
[    6.432825] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0    
[    6.440350] sunxi-rtc 1c20d00.rtc: RTC enabled                               
[    6.459569] ip_tables: (C) 2000-2006 Netfilter Core Team                     
[    6.469599] nf_conntrack version 0.5.0 (16155 buckets, 64620 max)            
[    6.586651] Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)
[    6.630894] usbcore: registered new interface driver r8188eu                 
[    6.653752] xt_time: kernel timezone is -0000                                
[    6.669711] PPP generic driver version 2.4.2                                 
[    6.675037] NET: Registered protocol family 24                               
[    8.910426]  No MAC Management Counters available                            
[    8.916491] device eth0 entered promiscuous mode                             
[    8.922833] br-lan: port 1(eth0) entered forwarding state                    
[    8.928299] br-lan: port 1(eth0) entered forwarding state                    
procd: - init complete -                                                        
[   10.899191] libphy: stmmac-0:01 - Link is Up - 100/Full                      
[   10.918935] br-lan: port 1(eth0) entered forwarding state                    
                                                                                
                                                                                
                                                                                
[   25.405391] random: nonblocking pool is initializedell (ash)                 
                                                                                
Enter 'help' for a list of built-in commands.                                   
                                                                                
  _______                     ________        __                                
 |       |.-----.-----.-----.|  |  |  |.----.|  |_                              
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|                             
 |_______||   __|_____|__|__||________||__|  |____|                             
          |__| W I R E L E S S   F R E E D O M                                  
 -----------------------------------------------------                          
 CHAOS CALMER (Bleeding Edge, r42689)                                           
 -----------------------------------------------------                          
  * 1 1/2 oz Gin            Shake with a glassful                               
  * 1/4 oz Triple Sec       of broken ice and pour                              
  * 3/4 oz Lime Juice       unstrained into a goblet.                           
  * 1 1/2 oz Orange Juice                                                       
  * 1 tsp. Grenadine Syrup                                                      
 -----------------------------------------------------                          
root@OpenWrt:/# 

root@OpenWrt:/# cat /proc/cpuinfo 
processor       : 0
model name      : ARMv7 Processor rev 4 (v7l)
Features        : swp half thumb fastmult vfp edsp vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xc07
CPU revision    : 4

processor       : 1
model name      : ARMv7 Processor rev 4 (v7l)
Features        : swp half thumb fastmult vfp edsp vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xc07
CPU revision    : 4

Hardware        : Allwinner sun7i (A20) Family
Revision        : 0000
Serial          : 0000000000000000

Tags

Back to top

toh/pcduino/pcduino3.txt · Last modified: 2014/09/28 18:51 by wigyori