Work in progress

This device is a mobile 150Mbits wireless 11n router with a very small form factor and two ethernet ports. It's design is focused on ease of configuration with a side switch to change operation mode to AP, router, or converter (wireless client). There are two references for this router (same hardware), MZK-MF150W for the white case, and MZK-MF150B for the black case.

Firmware content and case design suggests it's based on the "Abocom WR5204".

U-Boot 1.1.3 (Jun 15 2009 - 10:15:29)

Board: Ralink APSoC DRAM:  16 MB
relocate_code Pointer at: 80fac000
*** Error: config usb failed.
Config usb otg
flash_protect ON: from 0xBF000000 to 0xBF022F6F
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
============================================ 
Ralink UBoot Version: 3.2_a2
-------------------------------------------- 
ASIC 3052_MP2 (Port5<->None)
DRAM COMPONENT: 128Mbits 
DRAM BUS: 16BIT 
Total memory: 16 MBytes
Date:Jun 15 2009  Time:10:15:29
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384 

 ##### The CPU freq = 320 MHZ #### 

SDRAM bus set to 16 bit 
 SDRAM size =16 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: To emergency. 
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   Linux Kernel Image
   Created:      2010-03-04   9:25:29 UTC

 System Control Status = 0x00400000 
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3522496 Bytes =  3.4 MB
   Load Address: 80000000
   Entry Point:  8024f000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8024f000) ...
## Giving linux memsize in MB, 16

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.21 (root@linux-smoltz) (gcc version 3.4.2) #1 Thu Mar 4
17:24:12 CST 2010

 The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 10800008, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 00138800(1280000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13676k/16384k available (1988k kernel code, 2708k reserved, 372k data,
108k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 5 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x00130000 : "Kernel"
0x00130000-0x00400000 : "RootFS"
block2mtd: version $Revision: 1.1.1.1 $
nf_conntrack version 0.5.0 (128 buckets, 1024 max)
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
ClusterIP Version 0.8 loaded successfully
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00  64 rx/tx descriptors
allocated, mtu = 1500!
GDMA1_MAC_ADRH -- : 0x00000022
GDMA1_MAC_ADRL -- : 0xcfabe156
PROC INIT OK!
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 108k freed
init started: BusyBox v1.12.1 (2010-03-04 16:59:29 CST)
starting pid 72, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
devpts: called with bogus options
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to

 _______  ______  ______  ______ _______  __    __
|  ___  ||  ___ ||  __  || ___  ||  __  ||  \  /  |
| |___| || |___||| |  | || |  |_|| |  | ||   \/   |
|       ||  ___ || |  | || |   _ | |  | ||        |
|   _   || |___||| |__| || |__| || |__| ||        |
|__| |__||______||______||______||______||_/\__/\_|      


                     =System Architecture Department=

/etc_ro/rcS: line 9: telnetd: not found
starting pid 79, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2010-03-04 16:59:29 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# internet.sh
killall: pppd: no process killed
Password for 'admin' changed
/sbin/internet.sh: line 332: mdev: not found
mknod: /dev/sda6: File exists
mknod: /dev/sdb6: File exists
mknod: /dev/pts/0: Operation not permitted
mknod: /dev/pts/1: Operation not permitted
mknod: /dev/pts/2: Operation not permitted
mknod: /dev/pts/3: Operation not permitted
lm: no version for "struct_module" found: kernel tainted.
insmod: dwc_otg.ko: module not found
insmod: bridge.ko: module not found
insmod: mii.ko: module not found
insmod: raeth.ko: module not found

phy_tx_ring0 = 00f1a000, tx_ring0 = a0f1a000, size: 16 bytes

phy_tx_ring1 = 00f1b000, tx_ring1 = a0f1b000, size: 16 bytes

phy_tx_ring2 = 00f1c000, tx_ring2 = a0f1c000, size: 16 bytes

phy_tx_ring3 = 00f1d000, tx_ring3 = a0f1d000, size: 16 bytes

phy_rx_ring = 0x00000000, rx_ring = 0x00000000
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 10000
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_sta: No such file or directory
Load RT2880 Timer Module(Wdg/Soft)
rt2860v2_ap: module license 'unspecified' taints kernel.


=== pAd = c100d000, size = 495432 ===

<-- RTMPAllocAdapterBlock, Status=0
rmmod: nf_nat_pptp: No such file or directory
rmmod: nf_conntrack_pptp: No such file or directory
rmmod: nf_nat_proto_gre: No such file or directory
rmmod: nf_conntrack_proto_gre: No such file or directory
RX DESC a0ebb000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMPSetPhyMode: channel is out of range, use first channel=0 
MCS Set = ff 00 00 00 01
SYNC - BBP R4 to 20MHz.l
Main bssid = 00:22:cf:ab:e1:54
<==== rt28xx_init, Status=0
0x1300 = 00064380
insmod: 8021q.ko: module not found
eth2.2: Setting MAC address to  00 22 cf ab e1 55.
device eth2 entered promiscuous mode
VLAN (eth2.2):  Setting underlying device (eth2) to promiscious mode.
ifconfig: ioctl 0x8913 failed: No such device
##### config RT3052 vlan partition (WLLLL) #####
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1002
switch reg write offset=44, value=1001
switch reg write offset=48, value=1001
switch reg write offset=70, value=ffff417e
device ra0 entered promiscuous mode
eth2.1: dev_set_promiscuity(master, 1)
device eth2.1 entered promiscuous mode
udhcpc (v1.12.1) started
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
Set: phy[1].reg[0] = 3900
Set: phy[1].reg[0] = 3100
presentation_url=http://192.168.1.1 /var/miniupnpd.conf
killall: miniupnpd: no process killed
Reading configuration from file /var/miniupnpd.conf
perm rule added : allow 0-65535 c0a80101/ffffff00 0-65535
perm rule added : deny 0-65535 00000000/00000000 0-65535
Jan  1 00:00:13 miniupnpd[674]: listening on 192.168.1.1:6849
Jan  1 00:00:13 miniupnpd[674]: start miniupnpd
ifconfig: ioctl 0x8913 failed: No such device
/sbin/lan.sh: line 172: can't create /proc/sys/net/ipv6/conf/all/forwarding:
nonexistent directory
eth2.2: dev_set_promiscuity(master, 1)
device eth2.2 entered promiscuous mode
device br0 entered promiscuous mode
ip_table: set wan_name=eth2.2
ra1       no private ioctls.

ra2       no private ioctls.

ra3       no private ioctls.

ra4       no private ioctls.

ra5       no private ioctls.

ra6       no private ioctls.

ra7       no private ioctls.

br0: topology change detected, propagating
br0: port 2(eth2.1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(ra0) entering forwarding state
apcli0    no private ioctls.

killall rt2860apd 1>/dev/null 2>&1
iptables -F -t filter 1>/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter  1>/dev/null 2>&1
iptables -F web_filter  1>/dev/null 2>&1
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT
iptables -t filter -N web_filter 1>/dev/null 2>&1
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -N true_mac_filter 1>/dev/null 2>&1
iptables -A FORWARD -p UDP --dport 1701 -j DROP
iptables -A FORWARD -p UDP --dport 500 -j DROP
iptables -A FORWARD -p TCP --dport 1723 -j DROP
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j true_mac_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu
1>/dev/null 2>&1
iptables -t filter -A INPUT -i eth2.2 -p icmp -j DROP
iptables -A INPUT -i eth2.2 -p tcp --dport 80 -j DROP
iptables -A INPUT -i eth2.2 -j ACCEPT
iptables -t filter -F true_mac_filter
The tmpStr is eth2.2 
iptables -A OUTPUT -o eth2.2 -p tcp --dport 137:139 -j DROP
iptables -A OUTPUT -o eth2.2 -p udp --dport 137:139 -j DROP
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X
port_forward  1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null
2>&1
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING
ip_table: set wan_name=eth2.2
1 -j port_forward 1>/dev/null 2>&1
ip_table: set wan_name=eth2.2
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ
ip_table: set wan_name=eth2.2
1>/dev/null 2>&1
ip_table: set wan_name=eth2.2
/sbin/mini.sh
External IP = 10.10.10.1
ip_table: set wan_name=eth2.2
ip_table: set wan_name=eth2.2
iptables -o ppp0 -I FORWARD 1 -p tcp --tcp-flags SYN,RST SYN -m tcpmss --mss
1400:1536 -j TCPMSS --clamp-mss-to-pmtu
iptables -o ppp1 -I FORWARD 1 -p tcp --tcp-flags SYN,RST SYN -m tcpmss --mss
1400:1536 -j TCPMSS --clamp-mss-to-pmtu
ntp.sh
greenap.sh init
time.stdtime.gov.tw: Unknown host
ddns.sh
on
route delete 239.255.255.250 1>/dev/null 2>&1
killall wscd 1>/dev/null 2>&1
killall -9 wscd 1>/dev/null 2>&1
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
killall -q klogd
killall -q syslogd
syslogd -C8 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
killall -q zebra
killall -q ripd
/bin/qos_run
syslogd &
Commit crc = bd09eae8
Enter udps 

Start Read !!!
Current LSW : The status is 2 in the LSW
Current IN Flash Value ::: The opmode in flash is 1 
S:: The opmode in flash  is GW : 1 
Set to FLASH VALUE :: ==> The new_mode is 1 : 1 
status is 1 , state_flash is 1 
mount: mounting /dev/sda1 on /media failed: No such device
sh: ntfs-3g: not found
webs: Listening for HTTP requests at address 192.168.1.1

U-Boot 1.1.3 (Jun 15 2009 - 10:15:29)

Board: Ralink APSoC DRAM:  16 MB
relocate_code Pointer at: 80fac000
*** Error: config usb failed.
Config usb otg
flash_protect ON: from 0xBF000000 to 0xBF022F6F
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
============================================ 
Ralink UBoot Version: 3.2_a2
-------------------------------------------- 
ASIC 3052_MP2 (Port5<->None)
DRAM COMPONENT: 128Mbits 
DRAM BUS: 16BIT 
Total memory: 16 MBytes
Date:Jun 15 2009  Time:10:15:29
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384 

 ##### The CPU freq = 320 MHZ #### 

SDRAM bus set to 16 bit 
 SDRAM size =16 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: To emergency. 
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   MIPS OpenWrt Linux-3.3.8
   Created:      2013-03-03  16:11:17 UTC

 System Control Status = 0x00400000 
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    833387 Bytes = 813.9 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 16

Starting kernel ...

Linux version 3.3.8 (tibal@mokona) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #9 Sun Mar 3 17:10:50 CET 2013
bootconsole [early0] enabled
CPU revision is: 0001964c (MIPS 24KEc)
Ralink RT3350 id:1 rev:2 running at 320.00 MHz
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
Early memory PFN ranges
    0: 0x00000000 -> 0x00001000
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line:  board=MZKMF150 console=ttyS1,57600 mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2880k(rootfs),3776k@0x50000(firmware) rootfstype=squashfs,jffs2
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=000221e0
Readback ErrCtl register=000221e0
Memory: 13600k/16384k available (1906k kernel code, 2784k reserved, 316k data, 172k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:48
console [ttyS1] enabled, bootconsole disabled
console [ttyS1] enabled, bootconsole disabled
Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is Planex MZK-MF150
gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 26
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
physmap platform flash device: 00800000 at bf000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.1.
number of CFI chips: 1
6 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 6 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "u-boot-env"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000130000 : "kernel"
0x000000130000-0x000000400000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=130000 
0x0000002d0000-0x000000400000 : "rootfs_data"
0x000000050000-0x000000400000 : "firmware"
ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 40, using 40
TCP cubic registered
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 172k freed
Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
JFFS2 notice: (330) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -

Please press Enter to activate this console. Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
Backport based on wireless-testing.git master-2012-09-07
compat.git: wireless-testing.git
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
phy0 -> rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT305X.eeprom'.
phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 2872, rf: 0005, rev: 0200.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (215 buckets, 860 max)
dwc_otg: version 2.72a 24-JUN-2008
dwc_otg: Core Release: 2.66a
dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
dwc_otg: Multiprocessor Interrupt Enhancement - disabled
dwc_otg: Using DMA mode
dwc_otg: Device using Buffer DMA mode
dwc_otg dwc_otg.0: DWC OTG Controller
dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.1) entered forwarding state
br-lan: port 1(eth0.1) entered forwarding state
br-lan: port 1(eth0.1) entered forwarding state
ramips-wdt: timeout value 60 must be 0 < timeout <= 40, using 40



BusyBox v1.19.4 (2013-03-03 15:30:01 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 ATTITUDE ADJUSTMENT (Attitude Adjustment, unknown)
 -----------------------------------------------------
  * 1/4 oz Vodka      Pour all ingredients into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
 -----------------------------------------------------
root@OpenWrt:/#