Supported since R33886.

1. → obtain.firmware
2. → Install OpenWrt

You must set your TCP/IP v4 protocol to:

1. IP: 192.168.1.2
2. Netmask: 255.255.255.0
3. Gateway: 192.168.1.1
4. DNS: (optional, can be blank).

Then:

1. Power off the router.
2. Press reset button near the antenna.
3. Keep it pressed while powering up during ~20+ seconds.
4. Acces to http://192.168.1.1 and upload binary file.
5. Wait until router reboots.

→ generic.sysupgrade

If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

• Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
• Upload image file for sysupgrade to LuCI
• Wait for reboot

• Login as root via SSH on 192.168.1.1
• Use the following commands to upgrade.

cd /tmp/
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

• If sysupgrade does not support this router, use the following commands.

cd /tmp/
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

→ generic.failsafe

→ hardware.button on howto use and configure the hardware button(s).

F@ST2604 has only a reset button.

→ port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Photo of PCB with markings

Read: System configuration: Leds to configure the leds

→ hardware.button on howto use and configure the hardware button(s).

Sagem CFE version: 3.43 Build Date: Thu Jun 25 17:51:50 CST 2009 (chenc@svr1.sagem-szn.com) Copyright (C) 2005-2006 Sagem communication. Boot Address 0xbfc00000 Initializing Arena. Initializing Devices. Parallel flash device: name SST39VF3201, id 0x235b, size 4096KB Enter kerSysNvRamGet(CFE) getShareBlks: i=0, sect_size=4096, end_blk=1 kerSysNvRamGet(CFE) Mac address:c0:d0:44:4b:cd:00, BoardId=F@ST2604 getShareBlks: i=1010, sect_size=4096, end_blk=1016 getShareBlks: i=1011, sect_size=4096, end_blk=1016 getShareBlks: i=1012, sect_size=4096, end_blk=1016 getShareBlks: i=1013, sect_size=4096, end_blk=1016 getShareBlks: i=1014, sect_size=4096, end_blk=1016 getShareBlks: i=1015, sect_size=4096, end_blk=1016 Backup content:[ ] getShareBlks: i=1018, sect_size=4096, end_blk=1024 getShareBlks: i=1019, sect_size=4096, end_blk=1024 getShareBlks: i=1020, sect_size=4096, end_blk=1024 getShareBlks: i=1021, sect_size=4096, end_blk=1024 getShareBlks: i=1022, sect_size=4096, end_blk=1024 getShareBlks: i=1023, sect_size=4096, end_blk=1024 PSI content:[ ] Reset mii_switch_unmanage_mode configuration CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz Total memory: 16777216 bytes (16MB) Total memory used by CFE: 0x80401000 - 0x8052A990 (1218960) Initialized Data: 0x8041E2D0 - 0x80421100 (11824) BSS Area: 0x80421100 - 0x80428990 (30864) Local Heap: 0x80428990 - 0x80528990 (1048576) Stack Area: 0x80528990 - 0x8052A990 (8192) Text (code) segment: 0x80401000 - 0x8041E2CC (119500) Boot area (physical): 0x0052B000 - 0x0056B000 Relocation Factor: I:00000000 - D:00000000 Enter kerSysNvRamGet(CFE) getShareBlks: i=0, sect_size=4096, end_blk=1 kerSysNvRamGet(CFE) Mac address:c0:d0:44:4b:cd:00, BoardId=F@ST2604 Enter kerSysNvRamGet(CFE) getShareBlks: i=0, sect_size=4096, end_blk=1 kerSysNvRamGet(CFE) Mac address:c0:d0:44:4b:cd:00, BoardId=F@ST2604 Enter kerSysNvRamGet(CFE) getShareBlks: i=0, sect_size=4096, end_blk=1 kerSysNvRamGet(CFE) Mac address:c0:d0:44:4b:cd:00, BoardId=F@ST2604 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash (f) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Enter kerSysNvRamGet(CFE) getShareBlks: i=0, sect_size=4096, end_blk=1 kerSysNvRamGet(CFE) Mac address:c0:d0:44:4b:cd:00, BoardId=F@ST2604 Board Id (0-9) : F@ST2604 Number of MAC Addresses (1-32) : 11 Base MAC Address : c0:d0:44:4b:cd:00 PSI Size (1-64) KBytes : 24 Customer Name (0-4) : 4 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Enter kerSysNvRamGet(CFE) getShareBlks: i=0, sect_size=4096, end_blk=1 kerSysNvRamGet(CFE) Mac address:c0:d0:44:4b:cd:00, BoardId=F@ST2604 Code Address: 0x80010000, Entry Address: 0x801c6018 Booting from image (0xbfc10000) ... Decompression OK! Entry at 0x801c6018 Closing network. Starting program at 0x801c6018 Linux version 2.6.8.1 (chenc@svr1.sagem-szn.com) (gcc version 3.4.2) #1 Thu Jun 25 17:55:41 CST 2009 Parallel flash device: name SST39VF3201, id 0x235b, size 4096KB Total Flash size: 4096K with 1024 sectors fInfo.flash_scratch_pad_start_blk = 1016 fInfo.flash_scratch_pad_number_blk = 1 fInfo.flash_scratch_pad_length = 0x1000 fInfo.flash_scratch_pad_blk_offset = 0x0 system_ini_start_blk = 1017 system_ini_number_blk = 1 system_ini_blk_offset = 0x0 system_ini_length = 4096 fInfo.flash_nvram_start_blk = 0 fInfo.flash_nvram_blk_offset = 0x580 fInfo.flash_nvram_number_blk = 1 fInfo.flash_persistent_start_blk = 1018 fInfo.flash_persistent_blk_offset = 0x0 fInfo.flash_persistent_number_blk = 6 backup_start_blk = 1010 backup_blk_offset = 0x0 backup_number_blk = 6 backup_length = 24576 psi startAddr = bfffa000 systemini startAddr = bfff9000 sp startAddr = bfff8000 backup startAddr = bfff2000 F@ST2604 prom init CPU revision is: 00029107 Determined physical RAM map: memory: 00fa0000 @ 00000000 (usable) On node 0 totalpages: 4000 DMA zone: 4000 pages, LIFO batch:1 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 brcm mips: enabling icache and dcache... Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 8kB 2-way, linesize 16 bytes. PID hash table entries: 64 (order 6: 512 bytes) Using 128.000 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 13816k/16000k available (1520k kernel code, 2164k reserved, 228k data, 7 2k init, 0k highmem) Calibrating delay loop... 254.77 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Checking for 'wait' instruction... unavailable. NET: Registered protocol family 16 Can't analyze prologue code at 8018a874 usbcore: registered new driver hub Initializing Cryptographic API PPP generic driver version 2.4.2 NET: Registered protocol family 24 Using noop io scheduler bcm963xx_mtd driver v1.0 ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 PCI: Enabling device 0000:00:09.0 (0000 -> 0002) ohci_hcd 0000:00:09.0: OHCI Host Controller PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00 ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver brcmboard: brcm_board_init entry RestoreMacFilter: Button GPIO 0x21 is enabled RestoreMacFilter: Button Interrupt 0x1 is enabled RestoreMacFilter: Interrupt mapping OK Restore: Button GPIO 0x21 is enabled RestoreMacFilter: Button Interrupt 0x1 is enabled Restore: Interrupt mapping failed Serial: BCM63XX driver $Revision: 1.3 $ ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes ********* ip_rt_init ************ sizeof(struct rtable)=244 ip_rt_max_size=2048, rt_hash_mask=511, ipv4_dst_ops.gc_thresh=512, ip_rt_gc_interval=12000, rt_secret_rebuild=120000 TCP: Hash tables configured (established 512 bind 1024) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered NET: Registered protocol family 8 NET: Registered protocol family 20 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 72k freed init started: BusyBox v1.00 (2009.06.25-10:00+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 mount: Mounting tmpfs on /tmp failed: No such file or directory BusyBox v1.00 (2009.06.25-10:00+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... atmapi: module license 'Proprietary' taints kernel. adsl: adsl_init entry blaadd: blaa_detect entry Broadcom BCMPROCFS v1.0 initialized Broadcom BCM6348B0 Ethernet Network Device v0.3 Jun 25 2009 17:54:06 Config Ethernet Switch Through SPI Slave Select 0 Cfm wathcer has been setup! dgasp: kerSysRegisterDyingGaspHandler: eth0 registered eth0: MAC Address: C0:D0:44:4B:CD:00 PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:01.0 (0004 -> 0006) wl: srom not detected, using main memory mapped srom info (wombo board) wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000 wl0: MAC Address: C0:D0:44:4B:CD:01 wl0: Broadcom BCM4318 802.11 Wireless Controller 4.174.64.18.cpe1.0 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered eth0 Link UP. Cfm has been started to initiate! Read Flash: part=[PERSISTENT] Read Flash: part=[PERSISTENT] PSI has been initiated successfully! BcmAdsl_Initialize=0xC0070958, g_pFnNotifyCallback=0xC008E3C4 AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000 pSdramPHY=0xA0FFFFF8, 0x20 0x400 AdslCoreSharedMemInit: shareMemAvailable=18544 AdslCoreHwReset: AdslOemDataAddr = 0xA0FF05C4 AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered ATM proc init !!! ATM Config Management initiated successfully! ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack ip_conntrack_pptp version 2.1 loaded ip_nat_pptp version 2.0 loaded ip_conntrack_h323: init ip_nat_h323: initialize the module! BRCM NAT Caching v0.1 Nov 18 2006 14:56:48 BRCM NAT Cache: Hooking hit function @ c0058c64 ip_conntrack_rtsp v0.01 loading ip_nat_rtsp v0.01 loading Security configuration management initiated successfully! ==> Software Version: 3.43a4G <== Read Flash: part=[FACTORYINFO] Enter kerSysFactoryInfoGet: strLen[64],offset[0] FactoryInfo[1-10]=[LK02494201] device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state Setting SSID "Nenufar" Setting SSID "Guest" Setting country code using abbreviation: "ES" wlctl band b run 0 time! wlctl band b run 0 time! channel 6 selected device wl0 entered promiscuous mode br0: port 2(wl0) entering learning state br0: topology change detected, propagating br0: port 2(wl0) entering forwarding state device wl0.1 entered promiscuous mode br0: port 3(wl0.1) entering learning state br0: topology change detected, propagating br0: port 3(wl0.1) entering forwarding state hlist_add_head_rcu=[c2:d0:44:4b:cd:1]----------------- source->dev->name=[wl0] ,is_local=[0] device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state device wl0 left promiscuous mode br0: port 2(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 2(wl0) entering learning state br0: topology change detected, propagating br0: port 2(wl0) entering forwarding state device wl0.1 left promiscuous mode br0: port 3(wl0.1) entering disabled state device wl0.1 entered promiscuous mode br0: port 3(wl0.1) entering learning state br0: topology change detected, propagating br0: port 3(wl0.1) entering forwarding state EngDbg:- PSI Retrieve Status for PortMirrorStatus = 3 EngDbg:- In Effect Port Mirror Cfg ENGDBG :- In Effect Port Mirroring, status = 0 count = 0 Read Flash: part=[SCRATCH_PAD] Read Flash: part=[SCRATCH_PAD] Network initiated successfully! Read Flash: part=[SYSTEM_INI] Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offs et=[0] SystemIni[1-10]=[[quickSetu] Web Server initiated successfully! Read Flash: part=[SCRATCH_PAD] load /var/systemini.ini to dictionary success! Admin URL is blank, then don't start RemoteAutoUpgradeThread ========>Load the wireless_reload_monitor thread<======= sntp: host not found insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/n at_cache.ko': Success (17): Success --->syslog_options_up: blocksite unloged! insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/n at_cache.ko': Success (17): Success Cfm initiated successfully! CONSOLED launched Login: