User Tools

Site Tools


toh:sercom:shg1500

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:sercom:shg1500 [2013/03/06 16:32]
toh:sercom:shg1500 [2015/12/12 07:04] (current)
tmomas New bootlog formatting applied
Line 1: Line 1:
 +====== Sercom SHG1500 ======
  
 +This page is about the above mentioned device also know as Vodafone Station 2.
 +
 +===== Supported Versions =====
 +^ Version/​Model ​  ^ Launch Date   ^ S/N   ^ OpenWrt Version Supported ​  ^ Model Specific Notes   ^
 +| v1              |    2011-12 ​   | -     | -                           | -                      |
 +
 +===== Hardware Highlights =====
 +^ CPU                     ^ Ram      ^ Flash        ^ Network ​     ^ USB   ^ Serial ​  ^ JTag   ^
 +| Broadcom BCM6361KFEBG ​  | 128MiB ​  | 64MiB Nand   | 3 + 1 gigE   | Yes   | Yes      | ?      |
 +
 +Physical inspection revealed SoC SKU BCM6361KFEBG,​ but some other boards may have BCM6361EKFEBG.
 +
 +==== OEM bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​JELO
 +CPUJ
 +L1CI
 +JELO
 +CPUJ
 +L1CI
 +DRAM
 +----
 +PHYS
 +ZQDN
 +PHYE
 +DINT
 +LASY
 +USYN
 +MSYN
 +LMBE
 +PASS
 +----
 +ZBSS
 +CODE
 +DATA
 +L12F
 +MAIN
 +NAN1
 +BT00
 +NAN9
 +NAN9
 +NAN3
 +RFS1
 +NAN5
 +................................................................................
 +............................******* DSP: Found BCM96362 *******
 +******* DSP: In PCM Mode *******
 +******* DSP: PCM running in 16 bit mode *******
 +gInterruptCounter ​    = 0x811D7D84
 +gInterruptErrors ​     = 0x811D7D88
 +gNextRxDesc ​          = 0x811D7D64
 +gNextTxDesc ​          = 0x811D7D60
 +gDectTestMode ​        = 0x811d7d2c
 +gDectBuffStart ​       = 0x811d7d30
 +32 ms ECAN tail-length
 +*** gStartRxDesc[0] = 0xA61E2000
 +*** gBufferSizeBytes = 640
 +*** gStartTxDesc[0] = 0xA61E3000
 +halPcmInit 341 nextTxDesc = 0xA61E3000
 +halPcmInit 341 nextTxDesc = 0xA61E3008
 +halPcmInit 345 Ownership for TX desc not set. Use this buffer.
 +DSP: Interrupt Masks
 +---------------
 +IrqMask ​                  = 0x00000003
 +IrqMask1 ​                 = 0x00000010
 +
 +DSP: Interrupt Status
 +-----------------
 +IrqStatus ​                = 0x00000000
 +IrqStatus1 ​               = 0x00000000</​nowiki>​
 +</​WRAP>​\\
 +
 +The bootloader doesn'​t show the full boot log.
 +Note CFE seems to be blocked.
 +It doesn'​t receive any key from the serial.
 +
 +
 +===== Basic configuration =====
 +
 +==== Switch Ports (for VLANs) ====
 +Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
 +^ Port                  ^ Switch port   ^
 +| LAN 1                 | 1             |
 +| LAN 2                 | 2             |
 +| LAN 3                 | 3             |
 +| Internet (WAN) gigE   | 4             |
 +
 +==== Failsafe mode ====
 +-> [[doc:​howto:​generic.failsafe]]
 +
 +==== Buttons ====
 +-> [[doc:​howto:​hardware.button]] on howto use and configure the hardware button(s).
 +
 +The Sercom SHG1500 has two buttons. They are Reset and Secure Easy Setup. Here, we merely name the buttons, so we can use them in the above Howto:
 +^ BUTTON ​             ^ Event   ^
 +| Reset               | reset   |
 +| Secure Easy Setup   | ses     |
 +
 +===== Hardware =====
 +
 +==== Info ====
 +| **[[wp>​Instruction set|Architecture]]:​** ​   | [[wp>​MIPS architecture|MIPS]] |
 +| **Vendor:​** ​         | [[wp>​Broadcom]] |
 +| **[[doc:​techref:​Bootloader]]:​** ​    | [[doc:​techref:​bootloader:​CFE]] |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | BCM6361 |
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​       | 400 Mhz |
 +| **Flash-Chip:​** ​     | STMicroelectronics NAND512W3A2DN6 |
 +| **Flash size:​** ​     | 64 MiB NAND |
 +| **RAM:​** ​            | 128 MiB [[http://​www.nanya.com/​NanyaAdmin/​GetFiles.ashx?​ID=845|NANYA NT5TU64M16GG-AC]] / DDR2-800 |
 +| **Wireless:​** ​       | Broadcom integrated 2.4ghz/5Ghz 802.11abgn |
 +| **Ethernet:​** ​       | [[doc:​techref:​swconfig]] |
 +| **Internet:​** ​       | xDSL/​CABLE/​3g ​  |
 +| **USB:​** ​            | Yes 3 x 2.0     |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​  | [[#​Serial|Yes]] ​  |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​      | [[#​JTAG|Yes]] ​    |
 +
 +==== Photos ====
 +
 +[[http://​www.flickr.com/​photos/​rway/​sets/​72157629732755952/​]]
 +
 +==== Serial ====
 +
 +The serial port is J302, on the left of the soc
 +
 +{{:​media:​sercom:​shg1500_serial.jpg?​400x300|}}
 +
 +|   1 |          GND |
 +|   2 |           TX |
 +|   3 |   Vcc (3.3V) |
 +|   4 |           RX |
 +
 +Settings are 115200 8N1
 +
 +==== JTAG ====
 +Jtag port can be JP2 on the board top
 +
 +{{:​media:​sercom:​shg1500_jtag.jpg?​400x300|}}
 +
 +|   1 | TDO   | SRST   ​| ​  2 |
 +|   3 | TMS   | TDI    |   4 |
 +|   5 | TCK   | TRST   ​| ​  6 |
 +|   7 | GND   | N/A    |   8 |
 +
 +**WARNING**:​ a few people tested this pinout without success. Also pin 1 and 8 seems to be grounded while 7 does not, unlike this table shows.
 +
 +==== miniPCIe ====
 +
 +There is an empty layout for a mini-pcie socket U34.
 +
 +I think, it can be added easy.
 +
 +{{:​media:​sercom:​shg1500_mpcie.jpg?​400x300|}}
 +
 +==== SD socket ====
 +
 +There also an other empty layout for a SD socket T121. 
 +
 +{{:​media:​sercom:​shg1500_sd.jpg|}}
 +
 +===== Links =====
 +
 +//​Unfortunately,​ the thread has been removed because of legal threats from Vodafone: [[https://​twitter.com/​JackVendicator/​status/​489082981399924736]] //
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​bcm63xx bcm6361}}