You are here: OpenWrt Wiki » Table of Hardware » Telsey » Telsey CPVA502+W

Differences

This shows you the differences between two versions of the page.

--- toh:telsey:cpva502.w [2013/01/28 18:00]
danitool
+++ toh:telsey:cpva502.w [2013/01/31 12:53] (current)
danitool
@@ Line 21: / Line 21: @@
 <tr>
 <td><IMG SRC="/_media/meta/icons/tango/package-x-generic.png"></td>
-<td>Since this router has only 16 MiB RAM, Backfire version may behave better. Here a backport to Backfire. Patch and Backfire firmware: <br><a href="https://files.myopera.com/danitool/linux/Telsey_CPVA502_Backfire_10.03.2.zip">Telsey_CPVA502_Backfire_10.03.2.zip</a>
+<td>Since this router has only 16 MiB RAM, Backfire version may behave better. Here a backport to Backfire. Patch and Backfire firmware: <br><a href="https://files.myopera.com/danitool/linux/Telsey_CPVA502_Backfire_10.03.2.zip">Telsey_CPVA502_Backfire_10.03.2.zip</a><br>Execute the command: <br><code>mtd fixtrx linux</code><br>after the first boot.
 </td>
 </tr>
@@ Line 29: / Line 29: @@
 ===== Hardware Highlights =====
-^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
+^ SoC ^ RAM ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
-| BCM@256MHz | 16MiB | 4MiB | 2 x 1| slave | Yes | ? |
+| bcm6348@256MHz | 16MiB | 4MiB | 2 x 1| slave | Yes | Yes |
 ===== Installation =====
@@ Line 111: / Line 111: @@
 ^ Interface Name ^ Description ^ Default configuration ^
 | br-lan | LAN & WiFi | 192.168.1.1/24 |
-| eth0 | ETH0 | WAN |
+| eth0 | WAN | dhcp |
-| eth1 | ETH1 | LAN (bridged) |
+| eth1 | LAN | bridged |
 | wlan0 | WiFi | disabled (bridged) |
@@ Line 165: / Line 165: @@
 |  **Photo of PCB**  ||
 | {{:toh:telsey:telsey_arriba.jpg?400x350|}} | {{:toh:telsey:telsey_abajo.jpg?400x350|}} |
-==== Opening the case ====
+==== Serial ====
+-> [[doc:hardware:port.serial]] general information about the serial port, serial port cable, etc.
+How to connect to the Serial Port of this specific device:
+**Photo of PCB with markings**
+==== JTAG ====
+-> [[doc:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
+How to connect to the JTAG Port of this specific device:
+**Photo of PCB with markings**
+===== Debricking =====
+-> [[doc:howto:generic.debrick]]
+This is my bootloader backup [[http://files.myopera.com/danitool/linux/bootloaders/telsey_CPVA502+_MX29LV320CT_CFE.zip|telsey_CPVA502+_MX29LV320CT_CFE]] --- //danitool 2012/01/16 11:58//
+===== Bootloader Mods =====
+you could read about [[doc:techref:bootloader]] in general
+===== Hardware mods =====
+as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience!
+==== USB Mod ====
+Probably the USB slave could be converted to host. See -> [[toh:inventel:dv4210#usb.mod|Livebox1: Slave to Host MOD]]
+===== Bootlogs =====
 ==== OEM bootlog ====
 <HTML>
@@ Line 650: / Line 680: @@
 </HTML>
-==== Serial ====
+==== OpenWrt bootlog (Backfire)====
--> [[doc:hardware:port.serial]] general information about the serial port, serial port cable, etc.
+<HTML>
+<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
+<code>CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
+Build Date: ven lug 21 09:44:42 CEST 2006 (oliale@oliale.telsey.loc)
+Copyright (C) 2003,2004,2005 Telsey Telecommunications.
-How to connect to the Serial Port of this specific device:
+Boot Address 0xbfc00000
-**Photo of PCB with markings**
+Initializing Arena.
+Initializing Devices.
+Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
+MB Full-Duplex (auto-neg)
+Check consistency for image tag [1]: Found good image at partition [1]
+Check consistency for image tag [2]: No image found at partition [2]
+CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
+Total memory: 16777216 bytes (16MB)
-==== JTAG ====
+Total memory used by CFE:  0x80401000 - 0x80526FA0 (1204128)
--> [[doc:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
+Initialized Data:          0x8041E610 - 0x80420480 (7792)
+BSS Area:                  0x80420480 - 0x80424FA0 (19232)
+Local Heap:                0x80424FA0 - 0x80524FA0 (1048576)
+Stack Area:                0x80524FA0 - 0x80526FA0 (8192)
+Text (code) segment:       0x80401000 - 0x8041E60C (120332)
+Boot area (physical):      0x00527000 - 0x00567000
+Relocation Factor:         I:00000000 - D:00000000
-How to connect to the JTAG Port of this specific device:
+Board IP address                  : 192.168.1.1
+Host IP address                   : 192.168.1.100
+Gateway IP address                :
+Run from flash/host (f/h)         : f
+Default host run file name        : vmlinux
+Default host flash file name      : bcm963xx_fs_kernel
+Boot delay (0-9 seconds)          : 9
+Board Id Name                     : CPVA502+
+Psi size in KB                    : 24
+Number of MAC Addresses (1-32)    : 8
+Base MAC Address                  : 00:30:ab:00:00:01
+Ethernet PHY Type                 : Internal
+Memory size in MB                 : 16
-**Photo of PCB with markings**
+mac server test........................
+### Not default mac address
+### 00 30 ab 00 00 01
+*** Press any key to stop auto run (9 seconds) ***
+Auto run second count down: 0
+Code Address: 0x80010000, Entry Address: 0x80010000
+Decompression OK!
+Entry at 0x80010000
+Closing network.
+Starting program at 0x80010000
+Linux version 2.6.32.27 (dani@tool) (gcc version 4.3.3 (GCC) ) #2 Sun Jan 27 20:42:36 CET 2013
+Detected Broadcom 0x6348 CPU revision b0
+CPU frequency is 256 MHz
+MB of RAM installed
+registering 37 GPIOs
+board_bcm963xx: CFE version: 1.0.37-3.6
+bootconsole [early0] enabled
+CPU revision is: 00029107 (Broadcom BCM6348)
+board_bcm963xx: board name: CPVA502+
+Determined physical RAM map:
+ memory: 01000000 @ 00000000 (usable)
+Initrd not found or empty - disabling initrd
+Zone PFN ranges:
+  Normal   0x00000000 -> 0x00001000
+Movable zone start PFN for each node
+early_node_map[1] active PFN ranges
+: 0x00000000 -> 0x00001000
+Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
+Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
+PID hash table entries: 64 (order: -4, 256 bytes)
+Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
+Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
+Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
+Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
+Memory: 13472k/16384k available (2053k kernel code, 2912k reserved, 360k data, 132k init, 0k highmem)
+Hierarchical RCU implementation.
+NR_IRQS:128
+Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
+Mount-cache hash table entries: 512
+NET: Registered protocol family 16
+registering PCI controller with io_map_base unset
+bio: create slab <bio-0> at 0
+Switching to clocksource MIPS
+PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
+ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
+NET: Registered protocol family 2
+IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
+TCP established hash table entries: 512 (order: 0, 4096 bytes)
+TCP bind hash table entries: 512 (order: -1, 2048 bytes)
+TCP: Hash tables configured (established 512 bind 512)
+TCP reno registered
+NET: Registered protocol family 1
+audit: initializing netlink socket (disabled)
+type=2000 audit(0.312:1): initialized
+squashfs: version 4.0 (2009/01/31) Phillip Lougher
+Registering mini_fo version $Id$
+JFFS2 version 2.2. (NAND) (SUMMARY)  Â© 2001-2006 Red Hat, Inc.
+msgmni has been set to 26
+io scheduler noop registered
+io scheduler deadline registered (default)
+gpiodev: gpio device registered with major 254
+gpiodev: gpio platform device registered with access mask FFFFFFFF
+bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
+console [ttyS0] enabled, bootconsole disabled
+console [ttyS0] enabled, bootconsole disabled
+bcm963xx_flash: 0x00400000 at 0x1fc00000
+bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
+ CFI mfr 0x000000c2
+ CFI id  0x000022a7
+ Amd/Fujitsu Extended Query Table at 0x0040
+  Amd/Fujitsu Extended Query version 1.1.
+bcm963xx: Swapping erase regions for broken CFI table.
+number of CFI chips: 1
+cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
+bcm963xx_flash: Read Signature value of CFE1CFE1
+bcm963xx_flash: CFE bootloader detected
+bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
+bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
+bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
+bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000
+bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
+bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000
+bcm963xx_flash: Spare partition is 280000 offset and length 170000
+Creating 5 MTD partitions on "bcm963xx":
+x000000000000-0x000000010000 : "CFE"
+x000000010100-0x0000000f0000 : "kernel"
+mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
+x0000000f0000-0x0000003f0000 : "rootfs"
+mtd: partition "rootfs" set to be root filesystem
+mtd: partition "rootfs_data" created automatically, ofs=280000, len=170000
+x000000280000-0x0000003f0000 : "rootfs_data"
+x0000003f0000-0x000000400000 : "nvram"
+x000000010000-0x0000003f0000 : "linux"
+bcm63xx_enet MII bus: probed
+bcm63xx_enet MII bus: probed
+bcm63xx_wdt started, timer margin: 30 sec
+Registered led device: phone
+Registered led device: link
+Registered led device: eth1-nrst
+TCP westwood registered
+NET: Registered protocol family 17
+.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
+All bugs added by David S. Miller <davem@redhat.com>
+VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
+Freeing unused kernel memory: 132k freed
+Please be patient, while OpenWrt loads ...
+- preinit -
+Press the [f] key and hit [enter] to enter failsafe mode
+- regular preinit -
+switching to jffs2
+mini_fo: using base directory: /
+mini_fo: using storage directory: /overlay
+- init -
+Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
+bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Generic PHY]
+device eth1 entered promiscuous mode
+eth0: link UP - 100/full - flow control off
+Compat-wireless backport release: compat-wireless-2011-11-29
+Backport based on wireless-testing.git master-2011-12-01
+cfg80211: Calling CRDA to update world regulatory domain
+usbcore: registered new interface driver usbfs
+usbcore: registered new interface driver hub
+cfg80211: World regulatory domain updated:
+cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
+cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
+cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
+cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+usbcore: registered new device driver usb
+b43-phy0: Broadcom 4318 WLAN found (core revision 9)
+Registered led device: b43-phy0::tx
+Registered led device: b43-phy0::rx
+Registered led device: b43-phy0::radio
+Broadcom 43xx driver loaded [ Features: PL ]
+PPP generic driver version 2.4.2
+ip_tables: (C) 2000-2006 Netfilter Core Team
+NET: Registered protocol family 24
+nf_conntrack version 0.5.0 (212 buckets, 848 max)
+ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
+bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
+bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
+bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
+usb usb1: configuration #1 chosen from 1 choice
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 2 ports detected
-===== Debricking =====
--> [[doc:howto:generic.debrick]]
-This is my bootloader backup [[http://files.myopera.com/danitool/linux/bootloaders/telsey_CPVA502+_MX29LV320CT_CFE.zip|telsey_CPVA502+_MX29LV320CT_CFE]] --- //danitool 2012/01/16 11:58//
-===== Bootloader Mods =====
+BusyBox v1.15.3 (2013-01-27 14:49:55 CET) built-in shell (ash)
-you could read about [[doc:techref:bootloader]] in general
+Enter 'help' for a list of built-in commands.
-===== Hardware mods =====
-as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience!
-==== USB Mod ====
-Probably the USB slave could be converted to host. See -> [[toh:inventel:dv4210#usb.mod|Livebox1: Slave to Host MOD]]
+  _______                     ________        __
+ |       |.-----.-----.-----.|  |  |  |.----.|  |_
+ |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
+ |_______||   __|_____|__|__||________||__|  |____|
+          |__| W I R E L E S S   F R E E D O M
+ ---------------------------------------------------
+ Backfire (10.03.x Snapshot, r33081)
+ ---------------------------------------------------
+  * 1/3 shot Kahlua    In a shot glass, layer Kahlua
+  * 1/3 shot Bailey's  on the bottom, then Bailey's,
+  * 1/3 shot Vodka     then Vodka.
+ ---------------------------------------------------
+root@OpenWrt:/#
+</code>
+</p>
+</HTML>
 ===== Tags =====
 {{tag>bcm63xx bcm6348}}

toh/telsey/cpva502.w.1359392443.txt.bz2 · Last modified: 2013/01/28 18:00 by danitool

OpenWrt

Wiki Search

Actions

Donate

Translations

Differences