User Tools

Site Tools


toh:teltonika:rut5xx

Teltonika RUT5XX

Hardware Highlights

Version Status Target(s) Platform CPU Speed (MHz) Flash (MB) RAM (MB) Wireless NIC Wireless Standard Wired Ports USB
14.07 ramips rt305x Ralink RT3050 8MB (16MB) 32 MB integrated 11b/g/n 4x 100MBit Yes

Hardware

Flash Layout

root@OpenWrt:/# cat /proc/mtd

dev:    size   erasesize  name
mtd0: 00030000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "factory"
mtd3: 000e0000 00010000 "kernel"
mtd4: 006d0000 00010000 "rootfs"
mtd5: 00570000 00010000 "rootfs_data"
mtd6: 007b0000 00010000 "firmware"

Bootlogs

OEM bootlog

U-Boot 1.1.3 (Oct 18 2013 - 14:48:11) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb4000 config usb.. spi_wait_nsec: 25 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Teltonika UBoot Version: TLT_v1.0 -------------------------------------------- ASIC 3052_MP2 (Port5<->Phy) DRAM component: 256 Mbits SDR DRAM bus: 16 bit Total memory: 32 MBytes Flash component: SPI Flash Date:Oct 18 2013 Time:14:48:11 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 320 MHZ #### estimate memory size =32 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 0 9: Load Boot Loader code then write to Flash via TFTP. 3: System Boot system code via Flash. ## Booting image at bf050000 ... raspi_read: from:50000 len:40 . Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2014-04-11 13:59:23 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 869630 Bytes = 849.2 kB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:d44fe .............. Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 32 Starting kernel ... [ 0.000000] Linux version 3.3.8 (mantas@Mantas) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #5 Fri Apr 11 16:59:14 EEST 2014 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001964c (MIPS 24KEc) [ 0.000000] Ralink RT3350 id:1 rev:2 running at 320.00 MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=RUT5XX console=ttyS1,57600 mtdparts=spi0.0:192k(u-boot)ro,64k(devdata)ro,64k(devconf),896k(kernel),6976k(rootfs),7872k@0x50000(firmware) rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=0000fc8d [ 0.000000] Readback ErrCtl register=0000fc8d [ 0.000000] Memory: 29736k/32768k available (1991k kernel code, 3032k reserved, 330k data, 176k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:48 [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.010000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912) [ 0.090000] pid_max: default: 32768 minimum: 301 [ 0.090000] Mount-cache hash table entries: 512 [ 0.100000] NET: Registered protocol family 16 [ 0.110000] MIPS: machine is Teltonika RUT5xx [ 0.120000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0 [ 0.130000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1 [ 0.140000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2 [ 0.170000] bio: create slab <bio-0> at 0 [ 0.180000] Switching to clocksource MIPS [ 0.190000] NET: Registered protocol family 2 [ 0.200000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.220000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.250000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.260000] TCP reno registered [ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.280000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.290000] NET: Registered protocol family 1 [ 0.350000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.360000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.380000] msgmni has been set to 58 [ 0.390000] io scheduler noop registered [ 0.390000] io scheduler deadline registered (default) [ 0.410000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.420000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A [ 0.430000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.460000] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.470000] 6 cmdlinepart partitions found on MTD device spi0.0 [ 0.480000] Creating 6 MTD partitions on "spi0.0": [ 0.490000] 0x000000000000-0x000000030000 : "u-boot" [ 0.500000] 0x000000030000-0x000000040000 : "devdata" [ 0.520000] 0x000000040000-0x000000050000 : "devconf" [ 0.530000] 0x000000050000-0x000000130000 : "kernel" [ 0.550000] 0x000000130000-0x000000800000 : "rootfs" [ 0.560000] mtd: partition "rootfs" set to be root filesystem [ 0.570000] mtd: partition "rootfs_data" created automatically, ofs=5E0000, len=220000 [ 0.590000] 0x0000005e0000-0x000000800000 : "rootfs_data" [ 0.600000] 0x000000050000-0x000000800000 : "firmware" [ 0.630000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 40, using 40 [ 0.650000] TCP cubic registered [ 0.650000] NET: Registered protocol family 17 [ 0.660000] 8021q: 802.1Q VLAN Support v1.8 [ 0.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.710000] Freeing unused kernel memory: 176k freed [ 4.660000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0 [ 4.940000] Button Hotplug driver version 0.4.1 - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - [ 9.210000] JFFS2 notice: (352) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 70 of xref (0 dead, 60 orphan) found. switching to jffs2 - init - Please press Enter to activate this console. [ 15.260000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993 [ 15.270000] Backport based on wireless-testing.git master-2012-09-07 [ 15.290000] compat.git: wireless-testing.git [ 15.340000] cfg80211: Calling CRDA to update world regulatory domain [ 15.360000] cfg80211: World regulatory domain updated: [ 15.370000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 15.380000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 15.400000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 15.410000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 15.430000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 15.450000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 16.160000] usbcore: registered new interface driver usbfs [ 16.170000] usbcore: registered new interface driver hub [ 16.190000] usbcore: registered new device driver usb [ 16.220000] lib80211: common routines for IEEE802.11 drivers [ 17.320000] NET: Registered protocol family 15 [ 17.460000] Initializing XFRM netlink socket [ 17.720000] PPP generic driver version 2.4.2 [ 17.780000] tun: Universal TUN/TAP device driver, 1.6 [ 17.790000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 18.370000] GRE over IPv4 demultiplexor driver [ 18.410000] GRE over IPv4 tunneling driver [ 18.570000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 19.140000] NET: Registered protocol family 24 [ 19.190000] nf_conntrack version 0.5.0 (467 buckets, 1868 max) [ 20.060000] xt_time: kernel timezone is -0000 [ 20.360000] dwc_otg: version 2.72a 24-JUN-2008 [ 20.370000] dwc_otg: Core Release: 2.66a [ 20.580000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled [ 20.600000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled [ 20.610000] dwc_otg: Using DMA mode [ 20.620000] dwc_otg: Device using Buffer DMA mode [ 20.630000] dwc_otg dwc_otg.0: DWC OTG Controller [ 20.640000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1 [ 20.650000] dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000 [ 20.660000] dwc_otg: Init: Port Power? op_state=1 [ 20.670000] dwc_otg: Init: Power Port (0) [ 20.680000] hub 1-0:1.0: USB hub found [ 20.690000] hub 1-0:1.0: 1 port detected [ 20.870000] usbcore: registered new interface driver cdc_acm [ 20.880000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 21.090000] usbcore: registered new interface driver usbserial [ 21.100000] USB Serial support registered for generic [ 21.110000] usbcore: registered new interface driver usbserial_generic [ 21.120000] usbserial: USB Serial Driver core [ 21.160000] usbcore: registered new interface driver cdc_ether [ 21.520000] USB Serial support registered for GSM modem (1-port) [ 21.530000] usbcore: registered new interface driver option [ 21.540000] option: v0.7.2:USB Driver for GSM modems [ 21.630000] usb 1-1: new high-speed USB device number 2 using dwc_otg [ 21.860000] cdc_acm 1-1:1.0: This device cannot do calls on its own. It is not a modem. [ 21.880000] cdc_acm 1-1:1.0: ttyACM0: USB ACM device [ 21.900000] cdc_acm 1-1:1.2: This device cannot do calls on its own. It is not a modem. [ 21.910000] cdc_acm 1-1:1.2: ttyACM1: USB ACM device [ 21.930000] cdc_acm 1-1:1.4: This device cannot do calls on its own. It is not a modem. [ 21.950000] cdc_acm 1-1:1.4: ttyACM2: USB ACM device [ 21.970000] cdc_acm 1-1:1.6: This device cannot do calls on its own. It is not a modem. [ 21.990000] cdc_acm 1-1:1.6: ttyACM3: USB ACM device [ 22.010000] cdc_acm 1-1:1.8: This device cannot do calls on its own. It is not a modem. [ 22.030000] cdc_acm 1-1:1.8: ttyACM4: USB ACM device [ 22.040000] cdc_acm 1-1:1.10: This device cannot do calls on its own. It is not a modem. [ 22.060000] cdc_acm 1-1:1.10: ttyACM5: USB ACM device [ 22.090000] cdc_acm 1-1:1.12: This device cannot do calls on its own. It is not a modem. [ 22.110000] cdc_acm 1-1:1.12: ttyACM6: USB ACM device [ 33.950000] device eth0.1 entered promiscuous mode [ 33.960000] device eth0 entered promiscuous mode [ 33.990000] br-lan: port 1(eth0.1) entered forwarding state [ 34.000000] br-lan: port 1(eth0.1) entered forwarding state [ 36.000000] br-lan: port 1(eth0.1) entered forwarding state


OpenWrt bootlog

Insert bootlog here


Hardware

Info

Rev v1

Architecture: MIPS
Vendor: Ralink
Bootloader: U-Boot
System-On-Chip: RT3050 (MIPS 24K V4.12)
CPU/Speed 320 Mhz
Flash-Chip: ??
Flash size: 8192 KiB
RAM: 32 MiB
Wireless: RT3050 1x1 802.11n 2.4GHz
Ethernet: 4x 10/100MiBit/s
USB: Yes
Serial: Yes
JTAG:

Serial

The Board has a 2*7 pin card edge connector behind the power connector, the Serial Port works with 3,3v Voltage @57600 bauds

A1 UART RX
B1 UART TX
B3 GND

A is the bottom side

B is the upper side

Tags

toh/teltonika/rut5xx.txt · Last modified: 2016/01/28 12:19 by tmomas