User Tools

Site Tools


toh:tenda:4g301

Tenda 4G301

Serial Port

Pinout

On the other side of the PCB there are 2 test points.

The serial interface is 3.3V TTL levels (need USB cable and/or level converter to connect to a PC). Settings are 57k6 8N1 no flow control.

GPIO

  • in 2: button or usb-charging power
  • out 0: usb-power
  • out 2: LED 1
  • out 40: LED 5
  • out 41/42: LED 2 (incl.red one)
  • out 43: LED 4

Bootlogs

OEM bootlog

U-Boot 1.1.3 (Oct 21 2013 - 14:54:35) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. spi_wait_nsec: 29 spi device id: ef 40 16 0 0 (40160000) find flash: W25Q32BV raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.1.1.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Oct 21 2013 Time:14:54:35 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2970642 Bytes = 2.8 MB Load Address: 80000000 Entry Point: 8000c310 raspi_read: from:50040 len:2d5412 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c310) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (root@bogon) (gcc version 3.4.2) #143 Sat Jun 21 06:03:01 EDT 2014 The CPU feqenuce set to 580 MHz MIPS CPU sleep mode enabled. PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe PCIE: PLL power down for MT7620N CPU revision is: 00019650 (MIPS 24Kc) Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0003e67a Readback ErrCtl register=0003e67a Memory: 53100k/65536k available (4394k kernel code, 12436k reserved, 821k data, 6428k init, 0k highmem) NR_IRQS:128 MTK/Ralink System Tick Counter init... cd:804ffe78, m:214748, s:32 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource Ralink external timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Load Ralink Timer0 Module Load Ralink Timer1 Module RT3xxx EHCI/OHCI init. fuse init (API version 7.15) msgmni has been set to 103 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A brd: module loaded deice id : ef 40 16 0 0 (40160000) W25Q32BV(ef 40160000) (4096 Kbytes) mtd .name = raspi, .size = 0x00400000 (0M) .erasesize = 0x00000004 (0K) .numeraseregions = 65536 Creating 6 MTD partitions on "raspi": 0x000000000000-0x000000400000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x0000003f0000 : "Kernel" 0x0000003f0000-0x000000400000 : "Backup_config" rdm_major = 253 SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x43762077 Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x43762077 PROC INIT OK! PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 === pAd = c0003000, size = 806048 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.1.6 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver ums-usbat Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (829 buckets, 3316 max) ctnetlink v0.93: registering with nfnetlink. Create proc webstr success. matchsize=264 xt_time: kernel timezone is -0000 net/netfilter/xt_netcheck.c 137 ipt_netcheck init IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux TCP cubic registered NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> Freeing unused kernel memory: 6428k freed init started: BusyBox v1.12Algorithmics/MIPS FPU Emulator v1.5 .1 (2014-04-15 05:58:40 EDT) starting pid 32, tty '': '/etc_ro/rcS' Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= starting pid 47, tty '/dev/ttyS1': '/bin/login' (none) login: SOFT_WARE_VERSION V1.01.27 SOFT_WARE_VERSION V1.01.27 LANGUAGE_INFO en HW_VERSION V1.0 SVN_VERSION 537 BUILD_TIME Jun 21 2014 05:57:25 BACK config init OK, old crc=ace7c67b, real crc=ace7c67b ########## nvramDestroy=0 backUPDestroy=0 ########## none config destroy..., nothing to do Yes: ****** WeLoveLinux ****** Welcome to ... cat: can't open '/var/tenda_httpd.log': No such file or directory sh: cannot create /proc/sys/net/ipv4/conf/br0/accept_local: nonexistent directory usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for Sierra USB modem usbcore: registered new interface driver sierra sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems USB Serial support registered for debug usbcore: registered new interface driver debug ==>down wireless interface! RX DESC a32d0000 size = 2048 RTMP_TimerListAdd: add timer obj c0098438! RTMP_TimerListAdd: add timer obj c00638e8! RTMP_TimerListAdd: add timer obj c00638bc! RTMP_TimerListAdd: add timer obj c0063890! RTMP_TimerListAdd: add timer obj c000b018! RTMP_TimerListAdd: add timer obj c000ac0c! RTMP_TimerListAdd: add timer obj c000afe8! RTMP_TimerListAdd: add timer obj c000b324! RTMP_TimerListAdd: add timer obj c000b264! RTMP_TimerListAdd: add timer obj c000b294! RTMP_TimerListAdd: add timer obj c0065cec! RTMP_TimerListAdd: add timer obj c00658e0! RTMP_TimerListAdd: add timer obj c0065cbc! RTMP_TimerListAdd: add timer obj c0065ff8! RTMP_TimerListAdd: add timer obj c0065d1c! RTMP_TimerListAdd: add timer obj c0065d4c! RTMP_TimerListAdd: add timer obj c0065d7c! RTMP_TimerListAdd: add timer obj c006eda4! RTMP_TimerListAdd: add timer obj c006eec0! RTMP_TimerListAdd: add timer obj c006edd0! RTMP_TimerListAdd: add timer obj c00663a4! RTMP_TimerListAdd: add timer obj c00084d8! RTMP_TimerListAdd: add timer obj c00660b4! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = 0, D2 = 12, CalCode = 28 !!! RT6352_Temperature_Init : BBPR49 = 0x0 RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff6 Current Temperature from BBP_R49=0xfffffff2 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= f, phase= 1) IQCalibration Start! IQCalibration Done! CH = 1, (gain= f, phase= 0) TX IQ Calibration Done! internal ALC is not enabled in NVM ! MCS Set = ff ff 00 00 01 RTMP_TimerListAdd: add timer obj c0066680! Main bssid = c8:3a:35:2f:32:58 <==== rt28xx_init, Status=0 0x1300 = 00064380 Raeth v3.0 (Tasklet,SkbRecycle) phy_tx_ring = 0x02d72000, tx_ring = 0xa2d72000 phy_rx_ring0 = 0x02d73000, rx_ring0 = 0xa2d73000 SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x43762077 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 This crc is same as Old, ace7c67b, no need to write to flash. maclist: WLan[C8:3A:35:2F:32:58] Lan[C8:3A:35:2F:ra2880stop()...32Done :58] Wan[C8:3A:35:2F:32:5D] Free TX/RX Ring Memory! Raeth v3.0 (Tasklet,SkbRecycle) phy_tx_ring = 0x02d76000, tx_ring = 0xa2d76000 phy_rx_ring0 = 0x0336f000, rx_ring0 = 0xa336f000 SMACCR1 -- : 0x0000c83a SMACCR0 -- : 0x352f3258 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 ifconfig: SIOCSIFHWADDR: Device or resource busy ------------- WISP_MODE -------------- vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_ingress_map: No such device vconfig: ioctl error for set_egress_map: No such device vconfig: ioctl error for set_egress_map: No such device vconfig: ioctl error for set_egress_map: No such device vconfig: ioctl error for set_egress_map: No such device vconfig: ioctl error for set_egress_map: No such device vconfig: ioctl error for set_egress_map: No such device vconfig: ioctl error for set_egress_map: No such device vconfig: ioctl error for set_egress_map: No such device switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=81000000 switch reg write offset=2710, value=81000000 switch reg write offset=2604, value=20ff0003 switch reg write offset=2704, value=20ff0003 switch reg write offset=2610, value=81000000 switch reg write offset=2014, value=10001 switch reg write offset=2114, value=10001 switch reg write offset=2214, value=10001 switch reg write offset=2314, value=10001 switch reg write offset=2414, value=10002 switch reg write offset=2514, value=10001 device eth2.1 entered promiscuous mode device eth2 entered promiscuous mode device eth2.2 entered promiscuous mode br0: port 2(eth2.2) entering learning state br0: port 2(eth2.2) entering learning state br0: port 1(eth2.1) entering learning state br0: port 1(eth2.1) entering learning state Unable to open /etc/udhcpd.leases for reading Init tQoS dev success. open /dev/tQoS failed. Set: phy[0].reg[1] = 3900 Set: phy[0].reg[2] = 3900 Set: phy[0].reg[3] = 3900 device ra0 entered promiscuous mode br0: port 3(ra0) entering learning state br0: port 3(ra0) entering learning state br0: port 2(eth2.2) entering forwarding state br0: port 1(eth2.1) entering forwarding state 2000, 1, 1 usbcore: registered new interface driver cdc_ether /var/run/dnrd.pid /var/run/dnrd.pid ==>up wireless interface sucess!Create check wan thread, tid=00000402, ret=0 =====>func:main line:563 netctrl Go to loop NOW, soft version=V1.01.27------------- br0: port 3(ra0) entering forwarding state Httpd listen 192.168.2.1:80 main--504 semget error: or exist: File exists semId has exist 0 =====>func:handleMessage line:129 type=51------------- (none) login:


OpenWrt bootlog

starting openwrt via ram-image

============================================ Ralink UBoot Version: 4.1.1.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Oct 21 2013 Time:14:54:35 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 1 0 raspi_read: from:40028 len:6 1: System Load Linux to SDRAM via TFTP. Please Input new ones /or Ctrl-C to discard Input device IP (192.168.2.1) ==:192.168.2.11 Input server IP (192.168.2.64) ==:192.168.2.64 Input Linux Kernel filename () ==:uImage netboot_common, argc= 3 NetTxPacket = 0x83FE4E80 KSEG1ADDR(NetTxPacket) = 0xA3FE4E80 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done ETH_STATE_ACTIVE!! TFTP from server 192.168.2.64; our IP address is 192.168.2.11 Filename 'uImage'. TIMEOUT_COUNT=10,Load address: 0x80a00000 Loading: Got ARP REPLY, set server/gtwy eth addr (00:1c:ad:77:f2:0e) Got it ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################### done Bytes transferred = 3090502 (2f2846 hex) NetBootFileXferSize= 002f2846 raspi_read: from:30000 len:10000 Erasing SPI Flash... raspi_erase: offs:30000 len:10000 . Writing to SPI Flash... raspi_write: to:30000 len:10000 . done Automatic boot of image at addr 0x80A00000 ... ## Booting image at 80a00000 ... Image Name: MIPS OpenWrt Linux-3.18.21 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3090438 Bytes = 2.9 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 3.18.21 (daniel@box) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47238) ) #2 Fri Oct 23 04:42:48 CEST 2015 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is Tenda 4G301 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0003e66e [ 0.000000] Readback ErrCtl register=0003e66e [ 0.000000] Memory: 59320K/65536K available (2750K kernel code, 131K rwdata, 544K rodata, 1940K init, 192K bss, 6216K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] pinctrl core: initialized pinctrl subsystem [ 0.100000] NET: Registered protocol family 16 [ 0.120000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.140000] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.150000] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.160000] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.170000] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.180000] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.190000] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.200000] Switched to clocksource systick [ 0.210000] NET: Registered protocol family 2 [ 0.210000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.240000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.250000] TCP: reno registered [ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.270000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.280000] NET: Registered protocol family 1 [ 2.950000] rt-timer 10000100.timer: maximum frequency is 2441Hz [ 2.970000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 2.990000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.000000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 3.030000] msgmni has been set to 115 [ 3.040000] io scheduler noop registered [ 3.040000] io scheduler deadline registered (default) [ 3.060000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 3.070000] console [ttyS0] disabled [ 3.080000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A [ 3.090000] console [ttyS0] enabled [ 3.090000] console [ttyS0] enabled [ 3.110000] bootconsole [early0] disabled [ 3.110000] bootconsole [early0] disabled [ 3.130000] m25p80 spi32766.0: found w25q32, expected gd25q32 [ 3.140000] m25p80 spi32766.0: w25q32 (4096 Kbytes) [ 3.150000] 5 ofpart partitions found on MTD device spi32766.0 [ 3.160000] Creating 5 MTD partitions on "spi32766.0": [ 3.170000] 0x000000000000-0x000000030000 : "u-boot" [ 3.180000] 0x000000030000-0x000000040000 : "u-boot-env" [ 3.200000] 0x000000040000-0x000000050000 : "factory" [ 3.210000] 0x000000050000-0x0000003f0000 : "firmware" [ 3.250000] 0x0000003f0000-0x000000400000 : "u-boot-env2" [ 3.260000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 3.280000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 3.290000] rt2880_wdt 10000120.watchdog: Initialized [ 3.300000] TCP: cubic registered [ 3.310000] NET: Registered protocol family 10 [ 3.320000] NET: Registered protocol family 17 [ 3.330000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 3.360000] 8021q: 802.1Q VLAN Support v1.8 [ 3.380000] Freeing unused kernel memory: 1940K (8035b000 - 80540000) [ 3.400000] init: Console is alive [ 3.410000] init: - watchdog - [ 3.440000] usbcore: registered new interface driver usbfs [ 3.450000] usbcore: registered new interface driver hub [ 3.460000] usbcore: registered new device driver usb [ 3.480000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.490000] ehci-platform: EHCI generic platform driver [ 3.700000] phy phy-usbphy.0: remote usb device wakeup disabled [ 3.710000] phy phy-usbphy.0: UTMI 16bit 30MHz [ 3.720000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 3.730000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 3.750000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 3.780000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 3.790000] hub 1-0:1.0: USB hub found [ 3.800000] hub 1-0:1.0: 1 port detected [ 3.810000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.820000] ohci-platform: OHCI generic platform driver [ 3.830000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 3.850000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 3.860000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 3.930000] hub 2-0:1.0: USB hub found [ 3.940000] hub 2-0:1.0: 1 port detected [ 4.420000] init: - preinit - [ 4.520000] 8021q: adding VLAN 0 to HW filter on device eth0 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.690000] procd: - early - [ 7.700000] procd: - watchdog - [ 8.270000] procd: - ubus - [ 9.280000] random: ubusd urandom read with 14 bits of entropy available [ 9.300000] procd: - init - Please press Enter to activate this console. [ 9.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.900000] Loading modules backported from Linux version master-2015-07-21-0-g47cd203 [ 9.920000] Backport generated by backports.git backports-20150626-0-gc1a4168 [ 9.950000] cfg80211: World regulatory domain updated: [ 9.960000] cfg80211: DFS Master region: unset [ 9.970000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 9.990000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 10.000000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 10.020000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 10.030000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 10.050000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 10.070000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 10.090000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 10.100000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 10.180000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.200000] nf_conntrack version 0.5.0 (957 buckets, 3828 max) [ 10.260000] xt_time: kernel timezone is -0000 [ 10.280000] PPP generic driver version 2.4.2 [ 10.290000] NET: Registered protocol family 24 [ 10.310000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected [ 10.330000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 16.090000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 16.100000] device eth0.1 entered promiscuous mode [ 16.110000] device eth0 entered promiscuous mode [ 16.140000] br-lan: port 1(eth0.1) entered forwarding state [ 16.150000] br-lan: port 1(eth0.1) entered forwarding state [ 18.150000] br-lan: port 1(eth0.1) entered forwarding state BusyBox v1.23.2 (2015-10-23 04:36:59 CEST) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- DESIGNATED DRIVER (Bleeding Edge, r47238) ----------------------------------------------------- * 2 oz. Orange Juice Combine all juices in a * 2 oz. Pineapple Juice tall glass filled with * 2 oz. Grapefruit Juice ice, stir well. * 2 oz. Cranberry Juice ----------------------------------------------------- root@OpenWrt:/# root@OpenWrt:/# cat /tmp/sysinfo/ * v7t4g301 Tenda 4G301 root@OpenWrt:/# uptime 00:03:50 up 0 min, load average: 0.86, 0.22, 0.07


Tags

toh/tenda/4g301.txt · Last modified: 2015/12/02 19:49 by tmomas