Thomson ST706 WL
Hardware type : Wireless VoIP DSL modem
Supported Versions
| Version/Model | S/N | OpenWrt Version Supported | Model Specific Notes |
|---|---|---|---|
| v? | - | - | - |
WIP
Hardware Highlights
| CPU | Ram | Flash | Network | FXS | USB | Serial | JTag |
|---|---|---|---|---|---|---|---|
| Broadcom BCM6348 | 16 MiB | 4 MiB | 2 | 1 | No | Yes | ? |
VINETIC-1CPE: Single channel codec and VoIP DSP, G.729, G.723.1, iLBC, LEC, T.38, RTP
Installation
WIP
OEM easy installation
WIP
OEM installation using the TFTP method
WIP
Upgrading OpenWrt
WIP
LuCI Web Upgrade Process
WIP
Terminal Upgrade Process
WIP
Hardware
- CPU : Broadcom BCM6348KPGB
- Wifi : Broadcom BCM4318KFBG
- Ethernet : Broadcom BCM5241
- ROM : Spansion S29GL032A90 (flash 32 Mbit, 8/16 bits)
- RAM : Samsung K4S281632I-UC75 (SDRAM 128 Mbit, 16 bits, 133 Mhz)
- VoIP : Infineon PEB 3331 HT V2.1 VINETIC® -1CPE
Photos
Opening the case
Note: This will void your warranty!
- Remove 4 screws on the bottom of the case
- Use a flat screwdriver to open the clips: 2 on each the side and 1 left of the button in the front.
Serial
VCC | GND | RxD | TxD
JTAG
To be verified.
The JTAG port seems to be a using a MIPS EJTAG JTAG header pinout.
| 2 | GND | 4 | GND | 6 | GND | 8 | GND | 10 | GND | 12 | Not Connected | 14 | VREF |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | nTRST | 3 | TDI | 5 | TDO | 7 | TMS | 9 | TCK | 11 | nSRST | 13 | DINT |
Specific Configuration
Interfaces
The default network configuration is:
| Name | Type | UL Interfaces |
|---|---|---|
| loop | ip | |
| ethif1 | physical | ethport1 |
| ethif2 | physical | ethport2 |
| wlif1 | physical | WLAN |
| ceoc | dsl | |
| bridge | eth | LocalNetwork |
| OBC | bridge | bridge |
| ethport1 | bridge | bridge |
| RELAY | eth | |
| FXS | physical | |
| FXO | physical | |
| atm_Internet | atm | Internet_ppp |
| ethport2 | bridge | bridge |
| WLAN | bridge | bridge |
| Internet_ppp | ppp | Internet |
| Internet | *ip | |
| LocalNetwork | ip | |
Switch Ports (for VLANs)
Failsafe mode
Called kernel mode by the Thomson firmware update software.
Boot into failsafe mode
Push the reset button and maintain, then plug the router power supply while keeping the reset button pushed until the green light becomes orange (not just red).
What to do in failsafe mode?
It overrides any existing password so you can change the firmware shipped with your password protected router.
Buttons
- On/Off switch
- Reset button
- SpeedTouch button
Basic configuration
Defaul ST706WL address : http://192.168.1.254/
If you have login/pass locked Thomson ST706 WL and you can't access to WebGUI do next :
- Connect FT232RL USB Serial converter to Serial Port on board (J303)
- Hold Reset and SpeedTouch button for over 7 sec
- Hold SpeedTouch button to full load & prompting login & password
- Insert login : 'adsl' & password : <blank>
- Type : menu
- Create user → run service http → save configs → reboot system
- Connect to router WebGUI with new user account
Tags
toh/thomson/st706wl.txt · Last modified: 2013/04/27 18:45 by ua.alex-x