User Tools

Site Tools


toh:thomson:tcw710

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
toh:thomson:tcw710 [2017/11/08 23:18]
Hispano created
toh:thomson:tcw710 [2017/11/10 12:14] (current)
tmomas
Line 1: Line 1:
 ====== Thomson TCW710 ====== ====== Thomson TCW710 ======
 +
 +**<color red>​Impossible to support - insufficient RAM.</​color>​**
  
 ===== Hardware Highlights ===== ===== Hardware Highlights =====
 ^ CPU                ^ Ram    ^ Flash   ^ Network ​  ^ USB(Network) ​  ^ USB (host) ​  ^ Serial ​  ^ JTag   ^ ^ CPU                ^ Ram    ^ Flash   ^ Network ​  ^ USB(Network) ​  ^ USB (host) ​  ^ Serial ​  ^ JTag   ^
-| Broadcom BCM3349 ​  ​| ​16MB   | 4MB    | 1         | 1              | No           | Yes      | Yes    |+| Broadcom BCM3349 ​  ​| ​8MB   | 4MB    | 1         | 1              | No           | Yes      | Yes    |
  
 ===== Installation ===== ===== Installation =====
Line 21: Line 23:
 | **Flash size:​** ​        | 4 MB                         | | **Flash size:​** ​        | 4 MB                         |
 | **RAM-Chip:​** ​          | EtronTech EM639165TS-7G ​     | | **RAM-Chip:​** ​          | EtronTech EM639165TS-7G ​     |
-| **RAM:​** ​               | 16 MB                        |+| **RAM:​** ​               | MB                        |
 | **Wireless:​** ​          | Broadcom BCM4318KFBG 802.11b/g (onboard) ​                        | | **Wireless:​** ​          | Broadcom BCM4318KFBG 802.11b/g (onboard) ​                        |
 | **Ethernet:​** ​          | 1                            | | **Ethernet:​** ​          | 1                            |
Line 67: Line 69:
  
 <WRAP bootlog> <WRAP bootlog>
-<​nowiki>​+<​nowiki>​eCos - hal_diag_init 
 +Init device '/​dev/​ttydiag'​ 
 +Init tty channel: 80808f38 
 +Init device '/​dev/​tty0'​ 
 +Init tty channel: 80808f58 
 +Init device '/​dev/​haldiag'​ 
 +HAL/diag SERIAL init 
 +Init device '/​dev/​ser0'​ 
 +BCM 33XX SERIAL init - dev: 0.2 
 +Set output buffer - buf: 80875408 len: 2048 
 +Set input buffer - buf: 80875c08 len: 2048 
 +BCM 33XX SERIAL config 
 +0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::​InitStorageDrivers:​ (BFC Target) 
 +Configuring/​Loading Flash driver... 
 +0x00000014 [tStartup] BcmBfcStdEmbeddedTarget::​InitStorageDrivers:​ (BFC Target) 
 +Loading ProgramStore driver... 
 +0x0000001e [tStartup] BcmBfcStdEmbeddedTarget::​InitStorageDrivers:​ (BFC Target) 
 +Loading BootloaderStore driver... 
 +0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::​InitStorageDrivers:​ (BFC Target) 
 +Loading NonVol driver... 
 +0x00000028 [tStartup] BcmBfcStdEmbeddedTarget::​InitStorageDrivers:​ (BFC Target) 
 +Storage drivers initialized successfully. 
 +0x00000032 [tStartup] BcmBfcStdEmbeddedTarget::​InitDeviceAbstractions:​ (BFC Tar 
 +get) Creating singletons for ProgramStore/​BootloaderStore/​NonVol devices... 
 +Detecting the next image number that we will store to by default... 
 +0x3c Computing CRC32 over image2 to ensure that it is valid... 
 +ProgramStoreDeviceDriver::​ProgramStoreDriverIsHeaderValid:​ WARNING - ProgramSto 
 +re header HCS check failed! 
 +ProgramStoreDeviceDriver::​ProgramStoreDriverIsImageValid:​ WARNING - Header isn' 
 +t valid! 
 +0x3c Done computing CRC32! 
 +By default, we will dload to image number 2! 
 + 
 +By default, we will dload to block number 0! 
 + 
 +0x00000046 [tStartup] BcmBfcStdEmbeddedTarget::​InitDeviceAbstractions:​ (BFC Tar 
 +get) Device abstraction singletons created successfully. 
 + 
 +Function: SetHardcodeVendorProfile 
 +The ProfileMagic of image is not equal to 0xFFAAAAFF!!! 
 +0x0000005a [tStartup] BcmCmBpiNonVolSettings::​BcmCmBpiNonVolSettings:​ (Euro-Doc 
 +sis CM BPI NonVol Settings) WARNING - Singleton pointer is not NULL! There are 
 +multiple instances! Leaving the singleton pointer alone... 
 + 
 +Reading Permanent settings from non-vol... 
 +Checksum for permanent settings: 0xdc4b363a 
 +Settings were read and verified. 
 + 
 + 
 +Reading Dynamic settings from non-vol... 
 +Checksum for dynamic settings: 0x58dc6ce3 
 +Settings were read and verified. 
 + 
 +Creating SNMP agent cablemodem agent 
 +DON'T think we need to go here - so don'​t::::​ init_mib !!!! 
 +WARNING: netsnmp_brcm_create_tstring called with no address! 
 + 
 +If you pressed the '​s'​ key before this point, we will skip driver initialization 
 +... 
 +Creating DOCSIS Control Thread...
 </​nowiki>​ </​nowiki>​
 </​WRAP>​\\ </​WRAP>​\\
toh/thomson/tcw710.1510179490.txt.bz2 · Last modified: 2017/11/08 23:18 by Hispano