You are here: OpenWrt Wiki » Table of Hardware » TP-Link » TP-Link TL-MR3040

Differences

This shows you the differences between two versions of the page.

--- toh:tp-link:tl-mr3040 [2012/12/14 15:30]
meeuw
+++ toh:tp-link:tl-mr3040 [2013/06/17 21:30] (current)
jmac928
@@ Line 1: / Line 1: @@
 ====== TP-Link TL-MR3040 ======
+A portable router with an onboard 2000mAh [[#Tags|rechargeable_battery]]  [[toh/start#battery.operated.portable.routers|Portable Battery Operated]].   See also [[toh/tp-link/tl-mr10u|TP-Link TL-MR10U]], [[toh/tp-link/tl-mr11u|TP-Link TL-MR11U]], [[toh/tp-link/tl-mr12u|TP-Link TL-MR12U]], [[toh/tp-link/tl-mr13u|TP-Link TL-MR13U]] and [[toh/tp-link/tl-mr3020|TP-Link TL-MR3020]], [[toh/tp-link/tl-wr703n|TP-Link TL-WR703N]].\\
+Although it is marketed as a "3G/4G router", the TL-MR3040 does not include a 3G/4G modem. It simply means that the OEM firmware and GUI support a certain range of USB 3G/4G modems, but, OpenWRT supports USB modems too.\\
-A portable router with very similar hardware to the [[toh:tp-link:TL-MR11U]], which also has an onboard 2000mAh battery.
+{{:media:toh:tp-link:tl-mr3040-v2-04.jpg?400|TP-Link TL-MR3040 V2}}
-Other TP-Link routers with similar hardware are the [[toh:tp-link:TL-MR3020]] and [[toh:tp-link:TL-WR703N]].
-This router also does not include a 3G modem.
 ===== Supported Versions =====
-^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^
-| v1   |  2012-05  | - | {{:meta:icons:tango:48px-dialog-warning.svg.png?nolink&24 |Stability warning }} Trunk [[https://dev.openwrt.org/changeset/31845|R31845]]  | ethernet link detection bugged - fixed in [[https://dev.openwrt.org/changeset/32336|R32336]] |
-{{:meta:icons:tango:48px-dialog-warning.svg.png?nolink&24 |Stability warning }} Snapshot images are always risky. Check the forum discussion for latest opinions on available images.
+^ Version/Model ^ Launch Date ^ OpenWrt Version Supported ^ Model Specific Notes ^ Hardware differences ^
+| v1.0          | May 2012    | [[https://dev.openwrt.org/changeset/31845|Trunk R31845]] | Confirmed working |-|
+| v2.0          | January 2013| -  |  ???  | Mode Switch button |
+===== PirateBox and LibraryBox Support=====
+http://daviddarts.com/piratebox-diy-openwrt/
+http://jasongriffey.net/librarybox/
+===== Hardware Highlights =====
+^  CPU                  ^  Ram   ^  Flash  ^  Network   ^  USB   ^  Serial ^  JTag  ^
+| Atheros AR7240 @ 400MHz | 32 MiB | 4 MiB   | 1x 100MBit | 1x 2.0 | YES     | NO     |
+  * SoC: Atheros AR9331 rev1
+  * 802.11 b/g/n 150Mbps
+  * Powered via mini-USB (5V) or Li-ion Battery included (4-5 hours)
+  * Only 94g\\
-===== Hardware Highlights =====
-^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
-| AR9331@400MHz |32 MiB |4 MiB | 1x 100MBit | 2.0 x1 | YES | NO |
+===== TL-MR3040 and TL-MR11U differences =====
-===== Installation =====
+Althought MR3040 and MR11U seems similar on the outside, inside isn´t that similar. Here are the diffrences:
-As with most TP-Link Routers this one can be flashed using the TP-Link Webinterface. The webinterface is chinese, but [[http://192.168.1.1/userRpm/SoftwareUpgradeRpm.htm]] is the firmware upgrade page, just flash [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-tl-mr3040-v1-squashfs-factory.bin|this firmware file]].
+  * MR11U is chinese only
+  * MR3040(v1.0/v2.0) doesn´t has QSS button
+  * USP_POWER GPIO is diferrent
+  * Some buttons are in different sides with different looks
+  * Also the layers printed on the PCB is different as also some connections
+  * [[http://wiki.openwrt.org/_media/media/mr3040.mr11u.jpg|MR3040 compared to MR11U photo]]\\
-Please consult ->[[doc:howto:generic.flashing]] and also [[toh:tp-link:TL-MR11U]] and [[toh:tp-link:TL-MR3020]].
+===== Installation (only for v1.0) =====
-==== Flash under U-Boot ====
+So you can either download a daily-built snapshot or build your own from sources.
-  * The serial is **p1** layout: **__p1 |VCC|GND|RX|TX|__** NOTE: Seems like **GND** pin isn't connected properly. It could be worked around by just using **RX**|**TX** and attaching the **USB-Power** to the same USB-Host as the USB-to-TTL Adapter..
+  * Download the latest Attitude Adjustment RC1 snapshot from [[http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/openwrt-ar71xx-generic-tl-mr3040-v1-squashfs-factory.bin|here]] (recommended)
+  * Download the lastest trunk snapshot [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-tl-mr3040-v1-squashfs-factory.bin|here]] (risky)
+{{:meta:icons:tango:48px-dialog-warning.svg.png?nolink}} **WARNING**: Snapshot images are always risky. Check the forum discussion for latest opinions on available images.
+==== Method Using Web GUI (Recommended)====
+As with most TP-Link Routers this one can be flashed using the TP-Link Webinterface.
+Connect to the TL-MR3040 router via Ethernet cable at IP address 192.168.0.1, login to the router's web GUI (default login/password: admin / admin), and overwrite the factory firmware by installing the **openwrt-ar71xx-generic-tl-mr3040-v1-squashfs-factory.bin**  like a regular firmware update.
+Wait for the progress bar to finish twice (the device will reset itself in the process), and proceed with basic configuration as with any fresh OpenWRT install.
+==== Manual Flash under U-Boot Serial Console ====
+  * To install OpenWrt from the U-Boot console, you need to install a TFTP server on your computer.
+  * By default the server is set to 192.168.0.100, you can check detail by 'printenv'
+  * The serial layout is **p1**: ->[[toh:tp-link:tl-mr3040#serial.console]]
   * Setup serial console 115200 8n1, for example: **screen /dev/ttyUSB0 115200 ixoff**
-  * Enter "tpl" as soon as U-Boot announces "Autobooting in 1 seconds"
-  * Setup your eth0 to 192.168.1.100, you can check detail by 'printenv'
-  * Run blow command under U-Boot:
-  tftpboot 0x81000000 openwrt-ar71xx-generic-tl-mr3040-v1-squashfs-factory.bin
+Power up the TL-MR3040, after a 1-2 seconds U-Boot announces "Autobooting in 1 seconds", when displaying this enter tpl immediately.
-  erase 0x9f020000 +0x3c0000
-  cp.b 0x81000000 0x9f020000 0x3c0000
+<code>Autobooting in 1 seconds
-  bootm 9f020000
+[type tpl here]</code>
+You will get a U-Boot-console, it shows as **hornet>**, and you must enter the following commands:
+<code>hornet> tftpboot 0x81000000 openwrt-ar71xx-generic-tl-mr3040-v1-squashfs-factory.bin
+Using eth0 device
+TFTP from server 192.168.0.100; our IP address is 192.168.0.1
+Filename 'openwrt-ar71xx-generic-tl-mr3040-v1-squashfs-factory.bin'.
+Load address: 0x81000000
+Loading: #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         #################################################################
+         ######################################################
+done
+Bytes transferred = 3932160 (3c0000 hex)
+hornet> erase 0x9f020000 +0x3c0000
+First 0x2 last 0x3d sector size 0x10000                                                                                                        61
+Erased 60 sectors
+hornet> cp.b 0x81000000 0x9f020000 0x3c0000
+Copy to Flash... write addr: 9f020000
+done
+hornet> bootm 9f020000
+</code>
 ==== Upgrading OpenWrt ====
-->[[doc:howto:generic.sysupgrade]]
+->[[doc:howto:generic.sysupgrade]]\\
-==== Failsafe Mode ====
-//(currently unconfirmed)//
+==== Failsafe Mode ====
   - Switch on the router
   - Wait almost 5 sec
-  - Press the "Reset"
+  - Press the "Reset" for ~3sec
+  - The device is now in Failsafe-Mode
+  - You may access it by using telnet 192.168.1.1/24 or serial
+**The LEDs won't flash in Failsafe Mode**\\
+===== Restoring Original Firmware =====
+   * The process is similar to flash OpenWRT with U-boot serial console
+   * Download the original image [[http://www.tp-link.com/Resources/software/TL-MR3040_V1_120328.zip]]
+   * Don´t forget to enter "tpl" as soon as U-Boot announces "Autobooting in 1 seconds"
+<code>hornet> tftpboot 0x81000000 mr3040v1_en_3_12_11_up(120328).bin
+...
+hornet> erase 0x9f020000 +0x3c0000
+...
+hornet> cp.b 0x81000000 0x9f020000 0x3c0000
+...
+hornet> bootm 9f020000
+</code>
+===== Basic Configuration =====
+Since this part is identical to generic devices, see [[doc:howto:basic.config|Basic configuration]].\\
+===== Original Flash Layout =====
+Please read the article [[doc:techref:Flash Layout]] for a better understanding. It contains a couple of explanations. Then let's have a view at flash layout of this particular device:
+^   TP-Link MR3040  Flash Layout stock firmware           ^^^^^^
+^ Layer0       |                        spi0.0:            4096KiB          |||||
+^ Layer1       |  mtd0            |  mtd1              |    mtd2           |  mtd3            |  mtd4         |
+^ Size in KiB  |  128KiB          |  1024KiB           |   2816 KiB        |  64KiB           |  64KiB        |
+^ Name         |  **//u-boot//**  |  **//kernel//**    |  **//rootfs//**   |  **//config//**  |  **//art//**  |
+^ mountpoint   |  none            |  none              | /                 |  none            |  none         |
+^ filesystem   |  none            |  none              | SquashFS          |  none            |  none         |
+ART = Atheros Radio Test - it contains RF calibration data for the wifi. If it is missing or corrupt, wireless won't come up anymore.\\
-Now you are in failsafe mode. The LEDs won't flash in Failsafe Mode
 ===== Hardware =====
@@ Line 56: / Line 151: @@
 Remove back cover, remove battery. Unscrew two screws, open case in the corner next to the ethernet port (there is a small triangle here). Push a screwdriver into the hole next to the battery (closest to ethernet port) and pull cover until it snaps open. Next push in the screwdriver in the next corner next to the battery.
-==== USB Issue ====
+==== Info ====
-A problem has been detected with the USB interface on the device. When connected to different models of serial adaptor, it functions for a few minutes then fails. This can be resolved by putting a passive hub in-line with the device. Voltage and current testing will be performed to identify why this behaviour occurs.
+|^  ^ IC ^ Datasheet ^|
+|Processor| AR7240 | {{:toh:tp-link:atheros.ar7240.pdf}} |
+|Flash ROM| Spansion S25FL032P | http://www.spansion.com/Support/Datasheets/S25FL032P_00.pdf |
+|SDRAM| Zentel A3S56D40FTP | http://www.kean.com.au/oshw/WR703N/teardown/Zentel%20A3S56D40FTP%20DDR%20256Mb%20SDRAM.pdf |
+|Chipset (Wi-Fi controller)| AR9331 | http://see.sl088.com/w/images/6/69/AR9331.pdf |
+==== Serial Console ====
+== Pinout ==
+^1 ^2 ^3 ^4|
+|TX|RX|GND|VCC||P1|
+Pin 1 is clearly marked on the board.
+The right settings for accessing the serial console are as follows:
+Bits per second: **115200**\\
+Data bits: **8**\\
+Stop bits: **1**\\
+Parity: **None**\\
+Flow control: **None**\\
+=== U-Boot Bootloader Console ===
+The password to get the U-Boot prompt is **tpl**. You must type it quickly while the serial console is displaying:
+<code>[...]
+ag7240_phy_setup
+eth1 up
+eth0, eth1
+Autobooting in 1 seconds
+[type tpl here]</code>
+U-Boot accepts several commands. Type **help** to display the list of available commands.
+=== Linux Console ===
+Once the original firmware has booted up completely, you can press **return** to activate the Linux login prompt.
+<code>TL-MR3040 login: root
+password: 5up</code>\\
+==== Photos (v1.0) ====
+[[http://imageshack.us/a/img23/9454/mr3040front.jpg|Bigger front image, for better view]].
+{{:toh:tp-link:tl-mr3040-v11_small.jpg?800|Version 1.1 Main board}}
+{{:media:mr3040_back.jpg?800|Version 1.1 back}}
+{{:media:mr3040_battery.jpg?800}}\\
+==== TL-MR3040 Reverse Engineering ====
+The TL-MR3040 has been [[https://forum.openwrt.org/viewtopic.php?id=41714|teared down]] by Jarocks, wich was very useful to check the pinout. The investigation was complete thanks to doiga, also check the [[https://forum.openwrt.org/viewtopic.php?id=42466|forum]]\\
+==== GPIOs ====
+-> [[doc:hardware:port.GPIO]]
+The AR933x platform provides 28 GPIOs, some of them are used by the router for status LEDs, buttons and other stuff.
+**The TL-MR3040 provides 3 free GPIOs.**
+The table below shows the results of the investigation, based on the AR9331 datasheet:
+^  GPIO  ^ Available ^  AR9331 Pin ^  Description                    ^
+|      0 | R8        | A78   | Must have 0 value during bootstrap*    |
+|      1 | R11       | A77   | Must have 1 value during bootstrap    |
+|      2 | SPI_CS_0  | B49   | Used by SPI Flash                     |
+|      3 | SPI_CLK   | B51   | Used by SPI Flash                     |
+|      4 | SPI_MOSI  | B50   | Used by SPI Flash                     |
+|      5 | SPI_MISO  | A57   | Used by SPI Flash                     |
+|      6 | NC        |       |                                       |
+|      7 | NC        |       |                                       |
+|      8 | NC        |       |                                       |
+|      9 | SIN       | B68   | Serial INPUT (Rx)                     |
+|     10 | SOUT      | A79   | Serial OUTPUT (Tx)                    |
+|     11 | RESET SW  | B48   | Soft Reset Switch                     |
+|     12 | R84       | A56   | Must have 0 value during bootstrap    |
+|     13 | R12       | B66   | Must have 1 value during bootstrap    |
+|     14 | R9        | A76   | **unused** Pulled to ground           |
+|     15 | R10       | B65   | **unused** Pulled to ground           |
+|     16 | R13       | A75   | Must have 0 value during bootstrap    |
+|     17 | LED2      | B64   | LAN LED                               |
+|     18 | USB_POWER | A28   | Control USB Host Power                |
+|     19 | NC        |       |                                       |
+|     20 | R15       | A27   | **unused** Pulled to ground           |
+|     21 | NC        |       |                                       |
+|     22 | NC        |       |                                       |
+|     23 | NC        |       |                                       |
+|     24 | NC        |       |                                       |
+|     26 | LED3      | A51   | Wireless LAN  LED                     |
+|     27 | LED1      | B44   | 3G LED                                |
+|     28 | N/A       | A74   | Must have 0 value during bootstrap    |
+*GPIO_0 can be floating (i.e. resistors removed) during boostrap and the router still boots! //TESTED!!!//
+To make the GPIOs available via sysfs, the required ones have to be exported to userspace, as it is explained on a page of the [[http://squidge.sourceforge.net/gpio/|Squidge-Project]].
+\\
+==== LEDs ====
+How to configure LEDs in general, see the LED section in the [[doc/uci/system]].
+The TL-MR3040 has 5 LEDs:
+^ LED name       ^ LED color  ^ LED print      ^ Internal name       ^ Trigger         ^
+| Power (2 LEDs) | Green/Red  | Power/Charge symbol   | N/A (fixed supply)  | N/A      |
+| LAN            | Green      | LAN symbol     | tp-link:green:lan   | ''netdev:eth0'' |
+| Wireless LAN   | Green      | WLAN symbol    | tp-link:green:wlan  | ''phy0tpt''     |
+| 3G             | Green      | Internet symbol| tp-link:green:3g    | ''USB:1-1''     |\\
+==== USB Port ====
+Like other **devices using the ar933x platform**, this model suffers from problems when directly connecting USB 1.1 devices (specified for low speed or full speed; normally serial adapters). These problems can be circumvented by using a (passive) hub between the router and the USB devices. More information in the [[https://forum.openwrt.org/viewtopic.php?id=39956|forum]].
+**This problem can also be circumvented** by using an external powered USB HUB 2.0 //HIGH-SPEED//.
+\\
+===== Bootlog =====
+==== Factory BootLog ====
+<HTML>
+<div style="height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
+<p style="margin: 5px;padding:5px">
+<code>
+U-Boot 1.1.4 (Mar 28 2012 - 17:31:23)
+AP121 (ar9330) U-boot
+DRAM:  32 MB
+led turning on for 1s...
+id read 0x100000ff
+flash size 4194304, sector count = 64
+Flash:  4 MB
+Using default environment
+In:    serial
+Out:   serial
+Err:   serial
+Net:   ag7240_enet_initialize...
+No valid address in Flash. Using fixed address
+No valid address in Flash. Using fixed address
+: cfg1 0x5 cfg2 0x7114
+eth0:
+ag7240_phy_setup
+eth0 up
+:
+eth1:
+athrs26_reg_init_lan
+ATHRS26: resetting s26
+ATHRS26: s26 reset done
+ag7240_phy_setup
+eth1 up
+eth0, eth1
+Autobooting in 1 seconds
+## Booting image at 9f020000 ...
+   Uncompressing Kernel Image ... OK
+Starting kernel ...
+Booting AR9330(Hornet)...
+Linux version 2.6.31--LSDK-9.2.0.312 (root@local) (gcc version 4.3.3 (GCC) ) #22 Wed Aug 22 11:18:12 CST 2012
+flash_size passed from bootloader = 4
+CPU revision is: 00019374 (MIPS 24Kc)
+Determined physical RAM map:
+ memory: 02000000 @ 00000000 (usable)
+User-defined physical RAM map:
+ memory: 02000000 @ 00000000 (usable)
+Zone PFN ranges:
+  Normal   0x00000000 -> 0x00002000
+Movable zone start PFN for each node
+early_node_map[1] active PFN ranges
+: 0x00000000 -> 0x00002000
+Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
+Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ar7240-nor0:128k(u-boot),1024k(kernel),2816(rootfs),64k(config),64k(ART) mem=32M
+PID hash table entries: 128 (order: 7, 512 bytes)
+Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
+Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
+Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
+Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
+Writing ErrCtl register=00000000
+Readback ErrCtl register=00000000
+Memory: 29876k/32768k available (1884k kernel code, 2892k reserved, 521k data, 116k init, 0k highmem)
+Hierarchical RCU implementation.
+NR_IRQS:128
+plat_time_init: plat time init done
+Calibrating delay loop... 266.24 BogoMIPS (lpj=532480)
+Mount-cache hash table entries: 512
+NET: Registered protocol family 16
+===== ar7240_platform_init: 0
+bio: create slab <bio-0> at 0
+SCSI subsystem initialized
+usbcore: registered new interface driver usbfs
+usbcore: registered new interface driver hub
+usbcore: registered new device driver usb
+NET: Registered protocol family 2
+IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
+TCP established hash table entries: 1024 (order: 1, 8192 bytes)
+TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
+TCP: Hash tables configured (established 1024 bind 1024)
+TCP reno registered
+NET: Registered protocol family 1
+AR7240 GPIOC major 0
+squashfs: version 4.0 (2009/01/31) Phillip Lougher
+NTFS driver 2.1.29 [Flags: R/O].
+msgmni has been set to 58
+alg: No test for lzma (lzma-generic)
+alg: No test for stdrng (krng)
+io scheduler noop registered
+io scheduler anticipatory registered
+io scheduler deadline registered
+io scheduler cfq registered (default)
+Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
+ttyS0: detected caps 00000000 should be 00000100
+serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
+console [ttyS0] enabled
+PPP generic driver version 2.4.2
+NET: Registered protocol family 24
+cmdlinepart partition parsing not available
+set partition boot
+set partition kernel
+set partition rootfs
+set partition config
+set partition art
+set partition ÿ
+Searching for RedBoot partition table
+RedBoot partitions found on MTD device ar7240-nor0
+Creating 5 MTD partitions on "ar7240-nor0":
+x000000000000-0x000000020000 : "boot"
+x000000020000-0x000000120000 : "kernel"
+x000000120000-0x0000003e0000 : "rootfs"
+x0000003e0000-0x0000003f0000 : "config"
+x0000003f0000-0x000000400000 : "art"
+->Oops: flash id 0x10215 .
+ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+Port Status 1c000004
+ar7240-ehci ar7240-ehci.0: ATH EHCI
+ar7240-ehci ar7240-ehci.0: new USB bus registered, assigned bus number 1
+ehci_reset Intialize USB CONTROLLER in host mode: 3
+ehci_reset Port Status 1c000000
+ar7240-ehci ar7240-ehci.0: irq 3, io mem 0x1b000000
+ehci_reset Intialize USB CONTROLLER in host mode: 3
+ehci_reset Port Status 1c000000
+ar7240-ehci ar7240-ehci.0: USB 2.0 started, EHCI 1.00
+usb usb1: configuration #1 chosen from 1 choice
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 1 port detected
+TCP cubic registered
+NET: Registered protocol family 17
+.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
+All bugs added by David S. Miller <davem@redhat.com>
+ar7240wdt_init: Registering WDT success
+VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
+Freeing unused kernel memory: 116k freed
+init started:  BusyBox v1.01 (2012.08.01-03:58+0000) multi-call binary
+This Board use 2.6.31
+xt_time: kernel timezone is -0000
+nf_conntrack version 0.5.0 (512 buckets, 5120 max)
+ip_tables: (C) 2000-2006 Netfilter Core Team
+insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
+insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
+PPPoL2TP kernel driver, V1.0
+PPTP driver version 0.8.3
+insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
+ (none) mips #22 Wed Aug 22 11:18:12 CST 2012 (none)
+(none) login: Now flash open!
+Now flash open!
+ATHR_GMAC: Length per segment 1536
+ATHR_GMAC: fifo cfg 3 01f00140
+
+ATHR_GMAC: Max segments per packet :   1
+ATHR_GMAC: Max tx descriptor count :   40
+ATHR_GMAC: Max rx descriptor count :   96
+ATHR_GMAC: Mac capability flags    :   4D83
+
+ATHR_GMAC: Max segments per packet :   1
+ATHR_GMAC: Max tx descriptor count :   40
+ATHR_GMAC: Max rx descriptor count :   252
+ATHR_GMAC: Mac capability flags    :   4403
+athr_gmac_ring_alloc Allocated 640 at 0x81ea2800
+athr_gmac_ring_alloc Allocated 4032 at 0x81d63000
+Setting Drop CRC Errors, Pause Frames and Length Error frames
+Setting PHY...mac 0
+athr_gmac_ring_alloc Allocated 640 at 0x81ea2400
+athr_gmac_ring_alloc Allocated 1536 at 0x81f2f000
+athr_gmac_mii_setup: MDC check failed
+Setting Drop CRC Errors, Pause Frames and Length Error frames
+ATHRS26: resetting s26
+ATHRS26: s26 reset done
+Setting PHY...mac 1
+device eth0 entered promiscuous mode
+Now flash open!
+ATHR_GMAC: Enet Unit:1 PHY:4 is UP GMii 100Mbps full duplex
+ATHR_GMAC: done
+Setting Drop CRC Errors, Pause Frames and Length Error frames
+br0: port 1(eth0) entering forwarding state
+nf_conntrack_rtsp v0.6.21 loading
+nf_nat_rtsp v0.6.21 loading
+asf: module license 'Proprietary' taints kernel.
+Disabling lock debugging due to kernel taint
+ath_hal: 0.9.17.1 (AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
+ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
+ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
+ath_ahb: 9.2.0_U5.508 (Atheros/multi-bss)
+Boostrap clock 25MHz
+ar9300RadioAttach: Need analog access recipe!!
+Restoring Cal data from Flash
+ath_get_caps[4735] rx chainmask mismatch actual 1 sc_chainmak 0
+ath_get_caps[4710] tx chainmask mismatch actual 1 sc_chainmak 0
+wifi0: Atheros 9380: mem=0xb8100000, irq=2
+wlan_vap_create : enter. devhandle=0x80d202c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
+wlan_vap_create : exit. devhandle=0x80d202c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
+VAP device ath0 created
+.
+.
+.
+br0: port 2(ath0) entering forwarding state
+br0: port 2(ath0) entering disabled state
+TL-MR3040 login:
+</code>
+</p>
+</div>
+</HTML>\\
+===== Resources =====
+  * Official TP-Link TL-MR3040 [[http://www.tp-link.com/en/products/details/?model=TL-MR3040|Website]]
+  * The latest official firmware is available [[http://www.tp-link.com/en/support/download/?model=TL-MR3040|here]]
+  * OEM source code available at: http://www.tp-link.com/resources/gpl/150Router.rar
+  * [[http://www.disk91.com/2012/technology/systems/installation-of-a-piratebox-on-t-link-mr3040/|Installation of piratebox on T-Link MR3040]]
-==== Photos ====
+  * [[http://www.minipwner.com/|MiniPwner]] [[http://www.minipwner.com/index.php/forum/4-community-edition-installation/833-minipwner-based-on-tl-mr3040|confirmed working]]
-{{:toh:tp-link:tl-mr3040-v11_small.jpg?700|Version 1.1 Main board}}
+  * Althought [[toh:tp-link:TL-MR3020]] and [[toh:tp-link:TL-WR703N]] are ONLY hardware similar, most probably some modifications work, like External Antenna Hack!!!\\
 ===== Tags =====
 ----
-{{tag>FastEthernet 1Port Serial integrated 802.11bgn 1Radio AR9331 ath9k 1Ant 32RAM 4Flash MIPS MIPS32 24k AP121}}
+{{tag>FastEthernet 1NIC 1WNIC no_switch Serial integrated 1Ant 1USB 802.11bgn AR9331 ath9k 1Ant 32RAM 4Flash MIPS MIPS32 24k AP121 rechargeable_battery}}

toh/tp-link/tl-mr3040.1355495422.txt.bz2 · Last modified: 2012/12/14 15:30 by meeuw

This text is licensed under a Creative Commons Attribution-ShareAlike 3.0 Unported License.

OpenWrt

Wiki Search

Actions

Donate

Translations

Differences