Differences

This shows you the differences between two versions of the page.

toh:tp-link:tl-wdr4300 [2013/07/03 19:18]
lorema
toh:tp-link:tl-wdr4300 [2014/07/09 17:54] (current)
yuvadm
Line 1: Line 1:
======TP-Link TL-WDR4300====== ======TP-Link TL-WDR4300======
Dual Band (concurrent) and Gigabit Ethernet. Dual Band (concurrent) and Gigabit Ethernet.
-Advertised as 750 Mbps it is Dual-Stream (2x2) on the 2.4 Ghz Band and Triple-Stream (3x3) on the 5 Ghz Band. Same as the TL-WDR4310 Released earlier this year in China.+Advertised as 750 Mbps it is Dual-Stream (2x2) on the 2.4 Ghz Band and Triple-Stream (3x3) on the 5 Ghz Band. Same as the TL-WDR4310 Released earlier this year in China.
FCC ID = TE7WDR4300. FCC ID = TE7WDR4300.
 +
 +Related to TL-3600, which has only two instead of three antennas.
 +
Manufacturer product page is [[http://www.tplink.com/en/products/details/?categoryid=2166&model=TL-WDR4300|here]], while the support download page is [[http://www.tplink.com/en/support/download/?model=TL-WDR4300&version=V1#tbl_j|here]]. Manufacturer product page is [[http://www.tplink.com/en/products/details/?categoryid=2166&model=TL-WDR4300|here]], while the support download page is [[http://www.tplink.com/en/support/download/?model=TL-WDR4300&version=V1#tbl_j|here]].
The version 1.1 unit appears to use a SiGe SE2574L WFEs for 2.4 Ghz (20 dBm output) and SiGe SE5005L WFEs for 5 Ghz (18 dBm output) The version 1.1 unit appears to use a SiGe SE2574L WFEs for 2.4 Ghz (20 dBm output) and SiGe SE5005L WFEs for 5 Ghz (18 dBm output)
 +
 +**WARNING:** At least some of these routers seem to have unstable wifi in 12.09. They're hit by bugs [[https://dev.openwrt.org/ticket/12372|12372]] and [[https://dev.openwrt.org/ticket/13966|13966]].
 +
 +**NOTE:** The ethernet switch in this device, AR8327N, is working fine with the OpenWRT default configuration. But some of the more advanced functions of the switch are is not yet fully supported by the driver in 12.09. Most notably, a port cannot be tagged in some VLAN's and untagged in another, see [[https://dev.openwrt.org/ticket/12181|Bug 12181]]. A patch exists, but is not yet included in Trunk due to compatibility issues with older hardware.
{{:meta:icons:tango:dialog-warning.png?nolink |Warning!}}**WARNING:** Security warning: unpatched http/tftp backdoor in **original** firmware: [[http://sekurak.pl/tp-link-httptftp-backdoor/]] {{:meta:icons:tango:dialog-warning.png?nolink |Warning!}}**WARNING:** Security warning: unpatched http/tftp backdoor in **original** firmware: [[http://sekurak.pl/tp-link-httptftp-backdoor/]]
Line 12: Line 19:
===== Supported Versions ===== ===== Supported Versions =====
-^ Version/Model ^ S/N ^ Release Date ^ OpenWrt Version Supported ^ Model Specific Notes ^ +^ Version/Model ^ S/N ^ Board ID ^ Release Date ^ OpenWrt Version Supported ^ Model Specific Notes ^ 
-| v1.0 | - | 2012/02 | trunk [[https://dev.openwrt.org/changeset/32683|r32683]]  | [[.:TL-WDR4310|TP-Link TL-WDR4310]].| +| v1.0 | - | - | 2012/02 | trunk [[https://dev.openwrt.org/changeset/32683|r32683]]  | [[.:TL-WDR4310|TP-Link TL-WDR4310]].| 
-| v1.1 | - | 2012/06 | trunk [[https://dev.openwrt.org/changeset/32461|r32461]] | Similar to [[.:TL-WDR4310|TP-Link TL-WDR4310]]| +| v1.1 | - | - | 2012/06 | trunk [[https://dev.openwrt.org/changeset/32461|r32461]] | Similar to [[.:TL-WDR4310|TP-Link TL-WDR4310]]| 
-| v1.2 | - | 2012/11 | [[http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/|Attitude Adjustment 12.09 RC1]] | Similar to [[.:TL-WDR4310|TP-Link TL-WDR4310]]| +| v1.2 | - | - | 2012/11 | [[http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/|Attitude Adjustment 12.09 RC1]] | Similar to [[.:TL-WDR4310|TP-Link TL-WDR4310]]| 
-| v1.3 | - | 2012/11 | [[http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/|Attitude Adjustment 12.09 RC1]] | Similar to [[.:TL-WDR4310|TP-Link TL-WDR4310]]| +| v1.3 | - | - | 2012/11 | [[http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/|Attitude Adjustment 12.09 RC1]] and [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/|Attitude Adjustment 12.09 Final]] | Confirmed working with **Attitude Adjustment 12.09 Final**.\\ Similar to [[.:TL-WDR4310|TP-Link TL-WDR4310]]| 
-| v1.4 | - | 2013/04 | trunk [[https://dev.openwrt.org/changeset/36676|r36676]] | NEED to Toggle HW Wifi switch after first flash | +| v1.4 | - | - | 2013/04 | trunk [[https://dev.openwrt.org/changeset/36676|r36676]] | NEED to Toggle HW Wifi switch after first flash | 
-The latest firmware available is the release build [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/|Attitude Adjustment 12.09]] or the trunk build [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/|Barrier Breaker]], with working ethernet and dual-band wireless (disabled by default). If your wireless cannot be enabled when using wide channel modes, this may be due to the friendly neighbour "feature" that prohibits operation of such a mode and you may have to use the standard modes before wireless can be enabled.+| v1.5 | - | - | 2013/? | trunk [[https://dev.openwrt.org/changeset/37374|r37374]] | NEED to Toggle HW Wifi switch after first flash. Similar to v1.4, released between 2013/04 & 2013/07 | 
 +| v1.6 | - | - | 2013/08 | trunk [[https://dev.openwrt.org/changeset/37759|r37759]] and [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/|Attitude Adjustment 12.09 Final]] | Confirmed working with **Attitude Adjustment 12.09 Final**. | 
 +| v1.7 | - | 2050500272 rev 1.3 | 2014/01 | trunk [[https://dev.openwrt.org/changeset/39422|r39422]] | **Attitude Adjustment** does not work. [[https://forum.openwrt.org/viewtopic.php?pid=224008#p224008|more info]].  [[https://forum.openwrt.org/viewtopic.php?id=48226|General discussion]].  [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/openwrt-ar71xx-generic-tl-wdr4300-v1-squashfs-factory.bin|Attitude Adjustment 12.09 Final SquashFS Factory]] works for me.  This appears to be a problem only some people are experiencing. I was able to get Attitude Adjustment working fine with some fanagling [[https://forum.openwrt.org/viewtopic.php?pid=228641#p228641| this is how]]| 
 + 
 +The latest firmware available is the release build [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/|Attitude Adjustment 12.09 Final]] or the trunk build [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/|Barrier Breaker]], with working ethernet and dual-band wireless (disabled by default). If your wireless cannot be enabled when using wide channel modes, this may be due to the friendly neighbour "feature" that prohibits operation of such a mode and you may have to use the standard modes before wireless can be enabled.
===== Hardware Highlights ===== ===== Hardware Highlights =====
^ CPU ^ Flash ^ RAM ^ Network ^ WAN ^ USB ^ Serial ^ JTag ^ VLANs ^ ^ CPU ^ Flash ^ RAM ^ Network ^ WAN ^ USB ^ Serial ^ JTag ^ VLANs ^
| Atheros AR9344@560MHz  | 8MB | 128MB | 4x1 GigE | 1x1 GigE WAN| x2 v2.0| Yes | Yes | 128 | | Atheros AR9344@560MHz  | 8MB | 128MB | 4x1 GigE | 1x1 GigE WAN| x2 v2.0| Yes | Yes | 128 |
 +
 +===== Serial console =====
 +
 +Serial console is available on the J1 (1.7) connector, 3.3v signals.
 +
 +1 = TX out \\
 +2 = RX in \\
 +3 = GND \\
 +4 = VCC 3.3V \\
 +**DO NOT CONNECT VCC**. Use only TX/RX/GND.
 +
 +Baud Rate: 115200\\
 +Data Bits: 8\\
 +Parity: No\\
 +Stop Bits: 1\\
 +
 +To break bootstrap sequence, type '''tpl''' during the 1-second boot delay.
 +
 +Factory firmware login credentials are not known at this time (it's not root/5up as with other tp-link models).
 +
 +===== Flashing via TFTP ======
 +
 +Pressing the WPS/Reset button during powerup makes the bootstrap loader enter the TFTP recovery mode. The procedure can be used to transfer a firmware image:
 +  - assign 192.168.0.66 to your local network interface (the router uses 192.168.0.86)
 +  - publish a firmware image via tftp: ''cp openwrt-ar71xx-generic-tl-wdr4300-v1-squashfs-factory.bin /srv/tftp/wdr4300v1_tp_recovery.bin''
 +  - configure your tftp server
 +  - wait for the firmware transfer and subsequent reboot
===== Installation ===== ===== Installation =====
-  - [[doc:howto:obtain.firmware]] Download a pre-compiled release image [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/|Attitude Adjustment 12.09]] or trunk image [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/|Barrier Breaker]], look for openwrt-ar71xx-generic-tl-wdr4300-v1-squashfs-factory.bin. The precompiled images does not activate the wireless feature by default (you will have to use ethernet for the initial configuration), and does not include the web interface [[doc:howto:luci.essentials|LuCI]].+  - [[doc:howto:obtain.firmware]] Download a pre-compiled release image [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/|Attitude Adjustment 12.09]] or trunk image [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/|Barrier Breaker]], look for openwrt-ar71xx-generic-tl-wdr4300-v1-squashfs-factory.bin. The precompiled images does not activate the wireless feature by default (you will have to use ethernet for the initial configuration)
 +**NOTE:** Trunk images dont have luci you must install manually [[doc:howto:luci.essentials]] 
 + 
 +**NOTE:** Images with "-il-" in the name is specialised for devices sold in Israel, e.g. openwrt-ar71xx-generic-tl-wdr4300-v1-il-squashfs-factory.bin. For devices in Israel, try flashing the original image first. In case of failure (where the hardware ID does not match the existing firmware), fallback to the "-il-" image. There is no difference between the images otherwise. See [[http://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg17573.html|this thread]] for details.
  - [[doc:howto:generic.flashing]] Now write this firmware-file onto the flash-chip of your device   - [[doc:howto:generic.flashing]] Now write this firmware-file onto the flash-chip of your device
(For a brand new router, you could just use the vendor web UI to flash the .bin image) (For a brand new router, you could just use the vendor web UI to flash the .bin image)
  * To use wifi, you need to activate wifi in the configuration, see [[doc:uci:wireless|wireless configuration]].   * To use wifi, you need to activate wifi in the configuration, see [[doc:uci:wireless|wireless configuration]].
-  * The web interface LuCI can be installed and started via... 
-<code> 
-opkg update 
-opkg install luci 
-/etc/init.d/uhttpd enable 
-/etc/init.d/uhttpd start 
-</code> 
-An alternate SSL enabled version of LuCI is also available (opkg install luci-ssl). 
  * You can always [[doc:howto:obtain.firmware.generate|build]] your own image based on Attitude Adjustment/ trunk. Choose Atheros AR71xx/AT7240/AR913x platform and use the "TP-LINK TL-WDR4300 board support" profile.   * You can always [[doc:howto:obtain.firmware.generate|build]] your own image based on Attitude Adjustment/ trunk. Choose Atheros AR71xx/AT7240/AR913x platform and use the "TP-LINK TL-WDR4300 board support" profile.
Line 49: Line 82:
  - Flash Overwrite   - Flash Overwrite
  - Generic Sysupgrade   - Generic Sysupgrade
 +
 +(prior to actual flashing given availability of a serial console it's a nice idea to do dry runs, by ad-hoc RAM booting a factory.bin from a TFTP host server, via uboot "tftp" + "bootm", served via WDR3600's default 6F01A8C0.img filename).
=== Flash Overwrite === === Flash Overwrite ===
Line 73: Line 108:
Alternately, you can follow the [[doc:howto:generic.sysupgrade]] procedure. Don't forget to populate your ''/etc/sysupgrade.conf'' first. Alternately, you can follow the [[doc:howto:generic.sysupgrade]] procedure. Don't forget to populate your ''/etc/sysupgrade.conf'' first.
 +
 +=== mtd-utils ===
 +
 +For systems where OpenWrt mtd is not available, mtd-utils commands need to be used (subsequent commands boldly assume that it's mtd5 which equals the "firmware" mtd partition name - cat /proc/mtd to verify!!):
 +<code>
 +flash_eraseall /dev/mtd5
 +nandwrite /dev/mtd5 /tmp/openwrt-ar71xx-generic-tl-wdr4300-v1-squashfs-factory.bin
 +</code>
 +(write operation will take about 5 minutes to complete)
 +
 +Note that output of newer mtd-utils flash_eraseall recommends using "flash_erase <dev> 0 0" instead (did not test it).
==== Flash Layout ==== ==== Flash Layout ====
Line 99: Line 145:
==== Failsafe mode ==== ==== Failsafe mode ====
-Power up your router. When the 'SYS' light starts to blink you have about 1 seconds to press the WPS/Reset button on the back-left of the router and hold it until the blinking gets faster.+Power up your router. When the 'SYS' light (asterisk symbol right of the power light) starts to blink, immediately push the WPS/Reset button on the back-left of the router for a short time (>1 sec). The 'SYS' light should now start to blink very fast. 
 + 
 +On a TL-WDR4300 Ver 1.6 and Barrier Breaker Bleeding Edge, r39211, the above instructions were not terribly successful. The only way that I was able to get the router into failsafe mode was to quickly and repeatedly press the WPS/Reset button //starting before the front panel "star" LED started flashing. //When that LED finally lit, it appeared to go directly into the rapid-flashing "failsafe" indication. If the WPS LED lights (rightmost, "yin-yang arrows"), it may be that you started clicking the button a little early in the boot sequence.
For what you can do in failsafe, go to the [[doc:howto:generic.failsafe|OpenWrt Failsafe Mode]] page. For what you can do in failsafe, go to the [[doc:howto:generic.failsafe|OpenWrt Failsafe Mode]] page.
Line 145: Line 193:
  - copy your desired openwrt image for the tplink-4300 into your tftp server folder and rename it into openwrt.bin (to save some typing within the flash procedure)   - copy your desired openwrt image for the tplink-4300 into your tftp server folder and rename it into openwrt.bin (to save some typing within the flash procedure)
  - first goal is to get the command prompt from the u-boot bootloader on your router   - first goal is to get the command prompt from the u-boot bootloader on your router
 +  - you should only plug in the serial into the router's serial port AFTER it initialises for a split second after powering on BUT BEFORE Autobooting starts otherwise it might hang at the initialisation process
  - plug in your router and be ready to type ''tpl'' & hit ENTER after you see the line ''Autobooting in 1 seconds'':   - plug in your router and be ready to type ''tpl'' & hit ENTER after you see the line ''Autobooting in 1 seconds'':
Line 263: Line 312:
db12x> reset db12x> reset
</code> </code>
 +
 +===== Specific Configuration =====
 +==== Interfaces ====
 +
 +The default network configuration is:
 +^ Interface Name ^ Description ^ Default configuration ^
 +| br-lan | LAN & WiFi | 192.168.1.1/24 |
 +| vlan0 (eth0.0) | LAN ports (1 to 4) | None |
 +| vlan1 (eth0.1) | WAN port | DHCP |
 +| ? | WiFi | Disabled |
 +
 +==== Switch Ports (for VLANs) ====
 +Numbers 2-5 are Ports 1-4 as labeled on the unit, number 1 is the Internet (WAN) on the unit, 0 is the internal connection to the router itself.
 +^ Port ^ Switch port ^
 +| CPU  | 0 |
 +| WAN  | 1 |
 +| LAN 1 | 2 |
 +| LAN 2 | 3 |
 +| LAN 3 | 4 |
 +| LAN 4 | 5 |
 +| (not used) | 6 |
 +
 +The switch ports may turn out to be not properly bridged in a default bootup config, causing connection failure.
 +In this case you need to setup /etc/config/network or do manual swconfig setup - see [[http://wiki.openwrt.org/toh/buffalo/wbmr-hp-g300h#wired.stations.cannot.ping.each.other]] and [[http://wiki.openwrt.org/doc/uci/network/switch]] for advice.
 +
 +===== Bootloader Mods =====
 +  - you could read about [[doc:techref:bootloader]] in general and about [[doc:techref:bootloader:uboot|Das U-Boot]] in particular.
 +
 +==== U-Boot 1.1.4 modification for routers ====
 +Forum member [[https://forum.openwrt.org/profile.php?id=72549|pepe2k]] made a modification of **U-Boot 1.1.4** for **Qualcomm Atheros** SoCs based devices (the project is still being developed, so new devices and SoCs will be supported in the future). Up to date information, binary images and sources can be found on official [[https://github.com/pepe2k/u-boot_mod|GitHub repository]].
 +
 +This modification started from [[http://code.google.com/p/wr703n-uboot-with-web-failsafe/|wr703n-uboot-with-web-failsafe]] project, but supports more devices, all modern web browsers, has a lot of improvements and other modifications (like U-Boot NetConsole, custom commands, overclocking possibilities etc.).
 +
 +More information:
 +
 +  * Official repository on GitHub: [[https://github.com/pepe2k/u-boot_mod|U-Boot 1.1.4 modification for routers]]
 +  * Discussion about this project on [[https://forum.openwrt.org/viewtopic.php?id=43237|OpenWrt forum]]
 +  * An article (in Polish) about one of the first version of this project on [[http://www.tech-blog.pl/2013/03/29/zmodyfikowany-u-boot-dla-routerow-tp-link-z-atheros-ar9331-z-trybem-aktualizacji-oprogramowania-przez-www-i-konsola-sieciowa-netconsole/|www.tech-blog.pl]]
 +
 +==== Original bootloader settings ====
 +(for 1.7, at least)
 +<code>
 +db12x> printenv
 +bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),64k(mib0),64k(ART)
 +bootcmd=bootm 0x9f020000
 +bootdelay=1
 +baudrate=115200
 +ethaddr=0xXX:0xXX:0xXX:0xXX:0xXX:0xXX
 +ipaddr=192.168.1.111
 +serverip=192.168.1.100
 +dir=
 +lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize;cp.b $fileaddr 0x9f000000 $filesize
 +lf=tftp 0x80060000 ${dir}db12x${bc}-jffs2&&erase 0x9f050000 +0x630000;cp.b $fileaddr 0x9f050000 $filesize
 +lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f680000 +$filesize;cp.b $fileaddr 0x9f680000 $filesize
 +stdin=serial
 +stdout=serial
 +stderr=serial
 +ethact=eth0
 +
 +Environment size: 686/65532 bytes
 +db12x>
 +</code>
 +
 +Changing variables through '''setenv''' doesn't seem to make the changes stick, unfortunately.
===== Hardware ===== ===== Hardware =====
Line 276: Line 389:
| **RAM:**                      | 128 MiB  | | **RAM:**                      | 128 MiB  |
| **Wireless No1:**            | SoC-integrated: Atheros AR9340 2x2 MIMO for 2.4GHz 802.11b/g/n  | | **Wireless No1:**            | SoC-integrated: Atheros AR9340 2x2 MIMO for 2.4GHz 802.11b/g/n  |
-| **Wireless No2:**            | separate Chip: Atheros AR9580 5GHz 802.11an 3x3 MIMO for 5GHz 802.11a/n/ac |+| **Wireless No2:**            | separate Chip: Atheros AR9580 5GHz 802.11an 3x3 MIMO for 5GHz 802.11a/n  |
| **[[doc:hardware:Switch]]:**  | Atheros AR8327N  | | **[[doc:hardware:Switch]]:**  | Atheros AR8327N  |
| **USB:**            | Yes 2 x 2.0 (GL850G chip - 4 port's capable)    | | **USB:**            | Yes 2 x 2.0 (GL850G chip - 4 port's capable)    |
Line 298: Line 411:
| **Inner diameter**| 2.1mm | | **Inner diameter**| 2.1mm |
| **Length of the shaft** | 9.5mm | | **Length of the shaft** | 9.5mm |
 +
 +
 +=== GPIO ===
 +-> [[doc:hardware:port.GPIO]]
 +The AR933x platform provides 30 GPIOs. Some of them are used by the router for status LEDs, buttons and other stuff. The table below shows the results of some investigation:
 +
 +^        ^              ^            ^  Voltage level at GPIO in output-mode  ^^  gpioX/value in input-mode when GPIO is: ^^^
 +^  GPIO  ^  Common Name  ^  PCB Name  ^  gpioX/value=1  ^ gpioX/value=0        ^  Floating  ^  Pulled to GND  ^  Pulled to Vcc  ^
 +|      0 |      |  |                |                      |            |                |                  |
 +|      1 |              |            |                |                      |            |                |                  |
 +|      2 |              |            |                |                      |            |                |                  |
 +|      3 |              |            |                |                      |            |                |                  |
 +|      4 |              |            |                |                      |            |                |                  |
 +|      5 |              |            |                |                      |            |                |                  |
 +|      6 |              |            |                |                      |            |                |                  |
 +|      7 |              |  |                |                      |            |                |                  |
 +|      8 |    | |                |                      |            |                |                  |
 +|      9 |              |            |                |                      |            |                |                  |
 +|    10 |              |            |                |                      |            |                |                  |
 +|    11 | LED USB1    | DS8,R313          |                |                      |            |                |                  |
 +|    12 | LED USB2    | DS8,R314          |                |                      |            |                |                  |
 +|    13 | LED WLAN2G  | DS6          |                |                      |            |                |                  |
 +|    14 | LED System  | DS4          |                |                      |            |                |                  |
 +|    15 | LED QSS    | DS5          |                |                      |            |                |                  |
 +|    16 | WPS Button  |            |                |                      |            |                |                  |
 +|    17 | WiFi Switch  |            |                |                      |            |                |                  |
 +|    18 | External LNA0 |            |                |                      |            |                |                  |
 +|    19 | External LNA1 |            |                |                      |            |                |                  |
 +|    20 |                |            |                |                      |            |                |                  |
 +|    21 |  USB2 Power  |            |                |                      |            |                |                  |
 +|    22 |  USB1 Power  |            |                |                      |            |                |                  |
 +
 +To make the GPIOs available via sysfs, the required ones have to be exported to userspace, as it is explained on a page of the [[http://squidge.sourceforge.net/gpio/|Squidge-Project]]. Kernel modules occupying that resource need to be removed before (e.g. "leds-gpio" and "gpio-buttons"). In output-mode, voltage levels of the GPIOs were measured against GND, after the value 1 or 0 had been written to /sys/class/gpio/gpioX/value. In input-mode, the value of the file /sys/class/gpio/gpioX/value was read when the GPIO was floating (initial state), pulled to GND or pulled to Vcc.
 +
 +The 5GHz LED seems not to be controlled via GPIO.
==== Hardware Modifications ==== ==== Hardware Modifications ====
Line 353: Line 501:
With care, this method leaves no marks on the case. With care, this method leaves no marks on the case.
- 
-===== 12.09-rc1 (Attitude Adjustment Release Candidate) Configuration & Design Guide ===== 
- 
-==== Purpose and Scope ==== 
- 
-A developing guide covering recommended configuration, design and implementation of common features on the TL-WDR4300.  
- 
-Those evaluating the possible use of OpenWrt on the TL-WDR4300 may wish to review the [[howto:tl-wdr4300:datasheet|data sheet]], which details the verified hardware and software features of OpenWrt 12.09-rc1 on this platform. 
- 
-==== Currency and Structure ==== 
- 
-The guide is written specifically for 12.09-rc1, which is the latest stable build of OpenWrt. While there is no reason that much of the content could not apply to development snapshots, there is no guarantee that the content will be applicable. 
- 
-The guide is structured around a central [[howto:tl-wdr4300|contents page]].  
===== TP-Link TL-WDR4310 Version 1.0 forum thread ===== ===== TP-Link TL-WDR4310 Version 1.0 forum thread =====

Back to top

toh/tp-link/tl-wdr4300.1372871920.txt.bz2 · Last modified: 2013/07/03 19:18 by lorema