User Tools

Site Tools


toh:tp-link:tl-wdr7500

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
toh:tp-link:tl-wdr7500 [2013/07/10 18:44]
lorema
toh:tp-link:tl-wdr7500 [2014/12/05 19:26] (current)
aarioch added TFTP recovery info
Line 1: Line 1:
-====== TP-Link TL-WDR7500 / TP-Link Archer C7 AC1750 ======+====== TP-Link TL-WDR7500 / TP-Link Archer C7 AC1750 ​/ TP-Link Archer C5 AC1200======
 Dual Band (concurrent) and Gigabit Ethernet. Advertised as 1750 Mbps. It has simultaneous Triple-Stream (3x3) radios on both 2.4GHz and 5 GHz Bands. It supports 802.11n in 2.4GHz for 450Mbps throughput and [[#​Tags|IEEE 802.11ac (draft)]] for 1300Mbps throughput in 5GHz. Dual Band (concurrent) and Gigabit Ethernet. Advertised as 1750 Mbps. It has simultaneous Triple-Stream (3x3) radios on both 2.4GHz and 5 GHz Bands. It supports 802.11n in 2.4GHz for 450Mbps throughput and [[#​Tags|IEEE 802.11ac (draft)]] for 1300Mbps throughput in 5GHz.
  
-{{:​media:​toh:​tp-link:​tl-wdr7500:​archerc7.jpg?​300|TP-Link ​Archer C7 AC1750 V1}} +The TL-WDR7500, currently available in PRC only, has 6 external antennasThe Archer C7, available worldwide, has 3 internal (2.4GHz) and 3 external (5GHz) antennas.
-{{:​media:​toh:​tp-link:​tl-wdr7500:​tl-wdr7500.jpg?​300|TP-Link TL-WDR7500 V2}}+
  
-Manufacturer'​s siteV1 - [[http://www.tp-link.com/​en/​products/​details/​?categoryid=2872&​model=Archer+C7]],​ V2 [[http://www.tp-link.com.cn/​product_double_299.html]] +{{:media:toh:tp-link:​tl-wdr7500:​c7-2.png?300|TP-Link TL-WDR7500}} 
- +{{:​media:​toh:tp-link:tl-wdr7500:c7-1.png?300|TP-Link Archer C7 AC1750}}
-Forum[[https://forum.openwrt.org/​viewtopic.php?id=44201]]+
  
 ===== Supported Versions ===== ===== Supported Versions =====
 ^ Version/​Model ^ S/N ^ Release Date ^ OpenWrt Version Supported ^ Model Specific Notes ^ ^ Version/​Model ^ S/N ^ Release Date ^ OpenWrt Version Supported ^ Model Specific Notes ^
-| [[http://​wikidevi.com/​wiki/​TP-LINK_Archer_C7|Archer C7]] v1.0=?Archer C7   | 2013-01-15 |  [[https://​dev.openwrt.org/​changeset/​36790/​trunk|trunk r36790]] ​ | 3 internal and 3 external antennas, e.g. [[http://geizhals.de/tp-link-tl-wdr7500-archer-c7-mimo-dual-band-simultan-a923544.html|geizhals germany]], cf   | +WDR7500 v2.0 (Archer C7R)| - | 2013-01-15 | [[https://​forum.openwrt.org/​viewtopic.php?​pid=213547#​p213547|custom build with target support patch]] 2.4GHz only| 6 external antennas. QCA9880-AR1A (v1). Available only in PRC. [[https://​forum.openwrt.org/​viewtopic.php?​id=44201|WiP]] [[http://​www.tp-link.com.cn/​product_double_299.html|product page]] ​[[http://​wikidevi.com/​wiki/​TP-LINK_TL-WDR7500_v2.x|wikidevi]] [[http://​www.aliexpress.com/​wholesale?SearchText=TL-WDR7500|aliexpress]]| 
-| [[http://​wikidevi.com/​wiki/​TP-LINK_TL-WDR7500_v2.x|WDR7500]] v2.0 | - | 2013-01-15 | ??? | 6 external antennasavailable only in PRC?, any other differences ​to the Archer C7[[https://​forum.openwrt.org/​viewtopic.php?​id=44201|WiP]]  |+Archer C7 v1.0 | 2013-01-15 | [[https://​dev.openwrt.org/​changeset/​36790/​trunk|r36790]] ​2.4GHz only | 3 internal and 3 external antennas. ​QCA9880-AR1A (v1). [[http://wikidevi.com/wiki/​TP-LINK_Archer_C7|wikidevi]] [[http://​www.tp-link.com/​en/​products/​details/?​categoryid=2872&​model=Archer+C7|product page]] | 
 +| Archer C7 v1.1 | | 2013-??-?? | [[https://​forum.openwrt.org/​viewtopic.php?​pid=226678#​p226678|trunk]] 2.4GHz only| 3 internal and 3 external antennas. QCA9880-AR1A (v1)| 
 +| Archer C7 v2.0 | | 2013-12-17 | Early support in [[https://​dev.openwrt.org/​changeset/​40463|r40463]]-[[https://​dev.openwrt.org/​changeset/​40799|r40799]]. All working from [[https://​dev.openwrt.org/​ticket/​16589#​comment:​38|r41757]]3 internal and 3 external antennas. QCA9880-BR4A (v2). v2.0 printed on serial label on packaging. TP-Link support say "V2 has improved chipset which is DFS certificated. The flash capacity is 16MB compared to 8MB of V1. V2 also fixed a few bugs on V1". [[https://​forum.openwrt.org/​viewtopic.php?​pid=226595#​p226595|forum]] ​[[http://​blog.naver.com/​ckdalsdk12/​40208033303|photos]] [[http://​www.tp-link.com/​en/​support/​download/?​model=Archer+C7&​version=V2|stock firmware]] [[https://​wikidevi.com/​wiki/​TP-Link_Archer_C7_v2|wikidevi]] 
 +| WDR7500 v3.0 | - | 2014-??-?? ? | 6 external antennas. QCA9880-BR4A (v2). Currently ​available only in PRC [[https://​forum.openwrt.org/​viewtopic.php?id=51150|photos]]| 
 +| Archer C5 v1.20 | - | ? | Barrier Breaker | 3 internal and 3 external antennas. QCA9880-BR4A (v2). Same as C7 v2.0. Installation of OpenWrt was straightforward on this model | 
 + 
 +For the Archer C7 v1.x and WDR7500 v2.xthe 5GHz 802.11a/​n/​ac functionality is not supported, and likely will never be, since support for the AR1A (v1) variant of QCA9880 chip is not included in the open source ath10k driver. 
 +The Archer C7 v2.x uses the BR4A (v2) variant which is supported in ath10k [[http://​wireless.kernel.org/​en/​users/​Drivers/​ath10k|ath10k Linux]] 
 + 
 +===== Quick Start Guide ===== 
 +Barrier Breaker 14.07 provides full support for this router and has Luci (webUI) built-in. 
 + 
 +  * Download the 14.07 build of OpenWRT ​to your PC.  The files are located here: https://​downloads.openwrt.org/​barrier_breaker/​14.07/​ar71xx/​generic/​ download ​the *-factory.bin version 
 +    *Archer C7 V1.X https://​downloads.openwrt.org/​barrier_breaker/​14.07/​ar71xx/​generic/​openwrt-ar71xx-generic-archer-c7-v1-squashfs-factory.bin 
 +    *Archer C7 V2 https://​downloads.openwrt.org/​barrier_breaker/​14.07/​ar71xx/​generic/​openwrt-ar71xx-generic-archer-c7-v2-squashfs-factory.bin 
 +    *Archer C5 V1.X https://​downloads.openwrt.org/​barrier_breaker/​14.07/​ar71xx/​generic/​openwrt-ar71xx-generic-archer-c5-squashfs-factory.bin 
 +  * connect your PC to a LAN port of the TP-link. ​ Login to the TP-link web administration webpage. ​ Under '​System Tools' select '​Firmware Upgrade'​. ​ Browse to the previously downloaded *.bin file.  Click Upgrade. 
 +  * Connect to http://​192.168.1.1 with your web browser 
 +  * Set your password and configure the router through the web UI.  [[http://​wiki.openwrt.org/​doc/​howto/​basic.config|Basic Config]] 
 + 
 +**Note:** Luci for Barrier Breaker does not supporting configuring 802.11ac via the web GUI (supported in Chaos Calmer trunk branch as of 10/2014). To enable 802.11ac, run the following commands from the command line (telnet/​ssh):​ 
 +<​code>​uci set wireless.radio0.htmode=VHT80 
 +uci commit 
 +wifi 
 +</​code>​ 
 + 
 +Forum discussion/​support thread: ​[[https://​forum.openwrt.org/​viewtopic.php?​id=44201]] 
 + 
 +**Note**: Factory default IP address range is 192.168.0.1 while OpenWrt uses 192.168.1.1 by default. If you have trouble accessing your router after initial flash, check that you have a 192.168.1.x IP address on your PC. 
 + 
 +===== Hardware Highlights ===== 
 +^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ 
 +Qualcomm QCA9558@720MHz | 128MiB | 8MiB/16MiB | 4 x 1| Yes | Yes | Yes | 
 + 
 +Manufacturer'​s site: [[http://​www.tp-link.com/​en/​products/​details/?​categoryid=2872&​model=Archer+C7|Archer C7]] [[http://​www.tp-link.com.cn/​product_double_299.html|TL-WDR7500]]
  
-OEM source code available at: [[http://​www.tp-link.com/​resources/​gpl/​Archer_C7_1.0.tar.gz]] 
  
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-| **[[wp>​Instruction set]]:​** ​ | [[wp>​MIPS architecture|MIPS]] | + ​**Version:​** |  **TL-WDR7500 v2.x (Archer C7R)** ​ |  **Archer C7 v1.x** ​ |  **Archer C7 v2.x / C5**  | 
-| **Vendor:​** ​         | [[wp>​Qualcomm Atheros]] ​ | +|  ​**[[wp>​Instruction set]]:** |  [[wp>​MIPS architecture|MIPS]] ​ ||
-| **[[doc:​techref:​Bootloader]]:​** ​    ​| [[doc:​techref:​bootloader:​uboot|U-Boot]] (press **t** to enter U-Boot console on OEM firmware) | + **Vendor:** |  [[wp>​Qualcomm Atheros]]  ​||
-| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | QCA9558 (QCA9558-AT4A) 3x3 a/b/g/n (b/g/n, in this instance) | + **[[doc:​techref:​Bootloader]]:​** |  [[doc:​techref:​bootloader:​uboot|U-Boot]] (press **tpl** to enter U-Boot console on OEM firmware) ​ ||
-| **[[doc:​hardware:​cpu|CPU]]/​Speed:​** ​      ​| MIPS74Kc@720 MHz | + **[[doc:​hardware:​soc|System-On-Chip]]:​** |  QCA9558 (QCA9558-AT4A) 3x3 a/b/g/n (b/g/n, in this instance) ​ ||
-| **Flash Chip:​** ​     | cFeon Q64-104HIP | + **[[doc:​hardware:​cpu|CPU]]/​Speed:​** |  MIPS74Kc@720 MHz  ||
-| **Flash Specs:​** ​    ​| 8 MiB SPI | + **Flash Chip:** |  cFeon Q64-104HIP ​ ​| ​ Winbond W25Q64FV ​ |
-| **RAM Chip:​** ​       |  | + **Flash Specs:** |  8 MiB SPI  ​|| ​ 16 MiB SPI  ​
-| **RAM Specs:​** ​      ​| 128 MiB  | + **RAM Chip:** |  ​Hynix H5PS5162GFR-Y5C x 2  |  Winbond W9751G6KB-25 x 2  |
-| **Wireless No1:​** ​   | Integrated: QCA9558 3x3 b/g/n  | + **RAM Specs:** |  128 MiB  ​||
-| **Wireless No2:​** ​   | MiniPCIe: QCA9880-AR1A) 3x3 a/n/ac PCIe radio, requires ''​[[http://wireless.kernel.org/​en/​users/​Drivers/​ath10k|ath10k]]'' ​+ **Wireless No1:** |  Integrated: QCA9558 3x3 b/​g/​n  ​||
-| **[[doc:​hardware:​Switch]]:​** ​         | GbE [[http://www.qca.qualcomm.com/technology/technology.php?nav1=48&​product=102|AR8327N-AL1A]]  | + **Wireless No2:** |  MiniPCIe: QCA9880-AR1A ​(v1) 3x3 a/n/ac PCIe radio  ​|| ​ MiniPCIeQCA9880-BR4A (v2) 3x3 a/n/ac PCIe radio  ​
-| **USB:​** ​            ​| 2 x USB 2.0 | + **[[doc:​hardware:​Switch]]:​** |  GbE [[https://wikidevi.com/​files/​Atheros/​specsheets/​AR8327_AR8327N.pdf?​|AR8327N-AL1A]] ​ ||  GbE [[https://​wikidevi.com/files/Atheros/​specsheets/​AR8327_AR8327N.pdf?|AR8327N-BL1A]]  | 
-| **Power:​** ​          ​| External 12V ?A + **USB:** |  2 x USB 2.0  ||
-| **Serial:​** ​         | [[#​Serial|Yes]] | + **Power:** |  External 12V 2.5A  ||
-| **JTAG:​** ​           | Yes |+ **Serial:** |  [[#​Serial|Yes]] ​ ||
 + **JTAG:** |  Yes  ||| 
 + 
 +==== Power Consumption ==== 
 +The included power supply is rated at 2.5A at 12V (30W), but the router does not draw anywhere near the 30 Watts deliverable by that supply. ​ The extra capacity is useful for powering USB devices, however. ​ The following are power measurements taken of an Archer C7 AC1750 V2.0 measuring current over the DC wires. ​ The AC/DC adapter outputs 12.2V loaded. ​ A Kill-A-Watt power meter was used to confirm the measurements and showed the AC/DC adapter was fairly efficient. 
 + 
 + 
 +  * Stock firmware measurements 
 +    * booting draws between 2.4 and 3.5 W 
 +    * idle power 2.4 W 
 +    * downloading file over 2.4 GHz 3.6 W 
 +    * downloading over both 2.4 and 5 GHz 4.1 W 
 +    * flashing firmware 4.4 W 
 +  * OpenWRT firmware 
 +    * idle power 2.2 to 2.4 W 
 +    * downloading via wifi at 12 Mbps through router instance of OpenVPN w/​compression 3.1 W 
 + 
 + 
 +===== Configuration ===== 
 +  * [[https://​dev.openwrt.org/​changeset/​37507|switch port map]] 
 + 
 +Switch Ports: 
 +|0|eth1| 
 +|1|WAN| 
 +|2|LAN1| 
 +|3|LAN2| 
 +|4|LAN3| 
 +|5|LAN4| 
 +|6|eth0| 
 + 
 +==== Flash Layout ==== 
 + 
 +| 0x000000000000-0x000000020000 | "​u-boot"​ | 
 +| 0x000000020000-0x000000120000 | "​kernel"​ | 
 +| 0x000000120000-0x0000007e0000 | "​rootfs"​ | 
 +| 0x0000007e0000-0x0000007f0000 | "​config"​ | 
 +| 0x0000007f0000-0x000000800000 | "​ART"​ |  
 + 
 +==== Return to Factory Firmware ==== 
 +If you have accidentally flashed your V1 or V1.1 before realizing that the 5GHZ network card will not be supported, and want to return it to factory firmware, you can follow the following instructions (tested on V1.1, harvested from other tp-link device wikis) 
 + 
 +**The following instruction also works on V2** 
 + 
 +-> [[doc:​howto:​generic.uninstall]] 
 + 
 +{{page>​meta:​infobox:​dangerous&​noheader&​nofooter&​noeditbtn}} 
 + 
 +Obtain the factory firmware from the OEM: 
 +http://​www.tplink.com/​en/​support/​download/?​model=Archer+C7 
 + 
 +  * UNTESTED in case the file name of this firmware file does not contain the word **//"​boot"//​** in it, you can simply revert back to original firmware 
 +  * in case the file name of this firmware file does contain the word **//"​boot"//​** in it, you need to cut off parts of the image file //before// flashing it: 
 + 
 + 
 +An example of an image file with the word "​boot"​ in it is ''​ArcherC7v1_en_3_13_33_up_boot(130729).bin''​. 
 + 
 +Cut the first 0x20200 (that is 131,584 = 257*512) Bytes from original firmware (not sure why 0x20200, as the bootloader partition is only 0x20000, but it works!): 
 +<​code>​ 
 +dd if=orig.bin of=tplink.bin skip=257 bs=512 
 +</​code>​ 
 + 
 +You should transfer the firmeware image to the /tmp folder and revert back to original firmware (if available you can flash the firmware via the webinterface as well): 
 + 
 +Via the safer method using sysupgrade:​ 
 +<​code>​ 
 +sysupgrade /​tmp/​tplink.bin 
 +</​code>​ 
 + 
 +Or alternatively you can use the mtd method: 
 +<​code>​ 
 +mtd -r write /​tmp/​tplink.bin firmware 
 +</​code>​ 
 + 
 +==== TFTP Recovery ==== 
 + 
 +The serial-less TFTP recovery method for the [[toh:​tp-link:​tl-wdr4300|TP-Link TL-WDR4300]] also works for the Archer C7 (confirmed only on v2). For firmware revisions before 3.14.1 (140929), the router uses an IP address of 192.168.1.66 and looks for a file named ArcherC7v2_tp_recovery.bin. Firmware 3.14.1 updates the bootloader to use an IP address of 192.168.0.66 and look for a file named ArcherC7v3_tp_recovery.bin even on hardware v2 units. 
 + 
 +==== Benchmarks ==== 
 + 
 +Archer C7 USB benchmark results 
 + 
 +Using a Lexar L19 USB3.0 Stick (rated >40MB/s read/​write). Encrypted transfers reduce performance heavily. 
 + 
 +  * EXT2 USB -> Router -> SFTP -> PC : 2.6MB/s 
 +  * EXT2 USB -> Router -> SCP -> PC : 3.6MB/s 
 +  * EXT2 USB -> Router -> FTP (unencrypted) -> PC : 14.9-15.5MB/​s 
 +  * Router /dev/zero -> EXT2 USB : 10-19,​42MB/​s (depending on BS parameter of dd)
  
 ==== Photos ==== ==== Photos ====
Line 631: Line 748:
 <p style="​padding:​ 10px;​border:​1px solid grey;​height:​600px;​font:​10px/​14px Georgia, Garamond, Serif;​overflow:​Auto;​background-color:#​FFFFFF">​ <p style="​padding:​ 10px;​border:​1px solid grey;​height:​600px;​font:​10px/​14px Georgia, Garamond, Serif;​overflow:​Auto;​background-color:#​FFFFFF">​
 <​code>​ <​code>​
 +U-Boot 1.1.4 (Jan 26 2013 - 13:35:40)
 +
 +ap135 - Scorpion 1.0DRAM:  ​
 +sri
 +Scorpion 1.0
 +ath_ddr_initial_config(178):​ (32bit) ddr2 init
 +tap = 0x00000003
 +Tap (low, high) = (0x4, 0x1f)
 +Tap values = (0x11, 0x11, 0x11, 0x11)
 +128 MB
 +Flash Manuf Id 0x1c, DeviceId0 0x30, DeviceId1 0x17
 +flash size 8MB, sector count = 128
 +Flash: ​ 8 MB
 +Using default environment
 +
 +*** Warning *** : PCIe WLAN Module not found !!!
 +In:    serial
 +Out:   ​serial
 +Err:   ​serial
 +Net:   ​ath_gmac_enet_initialize...
 +athrs_sgmii_res_cal:​ cal value = 0xe
 +No valid address in Flash. Using fixed address
 +No valid address in Flash. Using fixed address
 +ath_gmac_enet_initialize:​ reset mask:​c02200 ​
 +Scorpion ​ ----> S17 PHY *
 +Vlan config...
 +TEST: FINAL REG VAL after TX Calibration - 0x46000000
 +TEST: FINAL XMII VAL after RX Calibration - 0x56000000
 +TEST: FINAL ETH_CFG VAL after RX Calibration - 0x00028001
 +athrs17_reg_init:​ complete
 +: cfg1 0x80000000 cfg2 0x7335
 +eth0: ba:​be:​fa:​ce:​08:​41
 +eth0 up
 +athrs17_reg_init_wan done
 +SGMII in forced mode
 +athr_gmac_sgmii_setup SGMII done
 +: cfg1 0x800c0000 cfg2 0x7214
 +eth1: ba:​be:​fa:​ce:​08:​41
 +eth1 up
 +eth0, eth1
 +Setting 0x18116290 to 0x50a1214f
 +Autobooting in 1 seconds
 +## Booting image at 9f020000 ...
 +   ​Uncompressing Kernel Image ... OK
 +
 +Starting kernel ...
 +
 +[    0.000000] Linux version 3.10.13 (nosferatu@work.g0x.ru) (gcc version 4.6.4 (OpenWrt/​Linaro GCC 4.6-2013.05 r38284) ) #1 3
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 00019750 (MIPS 74Kc)
 +[    0.000000] SoC: Qualcomm Atheros QCA9558 rev 0
 +[    0.000000] Clocks: CPU:​720.000MHz,​ DDR:​600.000MHz,​ AHB:​200.000MHz,​ Ref:​40.000MHz
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 08000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000] ​  ​Normal ​  [mem 0x00000000-0x07ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000] ​  ​node ​  0: [mem 0x00000000-0x07ffffff]
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
 +[    0.000000] Kernel command line:  board=ARCHER-C7 console=ttyS0,​115200 rootfstype=squashfs,​jffs2 noinitrd
 +[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
 +[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
 +[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Writing ErrCtl register=00000000
 +[    0.000000] Readback ErrCtl register=00000000
 +[    0.000000] Memory: 126312k/​131072k available (2196k kernel code, 4760k reserved, 588k data, 220k init, 0k highmem)
 +[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0,​ CPUs=1, Nodes=1
 +[    0.000000] NR_IRQS:51
 +[    0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
 +[    0.060000] pid_max: default: 32768 minimum: 301
 +[    0.060000] Mount-cache hash table entries: 512
 +[    0.070000] NET: Registered protocol family 16
 +[    0.070000] MIPS: machine is TP-LINK Archer C7
 +[    0.080000] ar724x-pci ar724x-pci.0:​ PCIe link is down
 +[    0.080000] registering PCI controller with io_map_base unset
 +[    0.090000] registering PCI controller with io_map_base unset
 +[    0.500000] bio: create slab <​bio-0>​ at 0
 +[    0.500000] PCI host bridge to bus 0000:00
 +[    0.510000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
 +[    0.510000] pci_bus 0000:00: root bus resource [io  0x0000]
 +[    0.520000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 +[    0.520000] PCI host bridge to bus 0000:01
 +[    0.530000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
 +[    0.530000] pci_bus 0000:01: root bus resource [io  0x0001]
 +[    0.540000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
 +[    0.540000] pci 0000:​01:​00.0:​ BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
 +[    0.550000] pci 0000:​01:​00.0:​ BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
 +[    0.550000] pci 0000:​01:​00.0:​ using irq 41 for pin 1
 +[    0.560000] Switching to clocksource MIPS
 +[    0.560000] NET: Registered protocol family 2
 +[    0.570000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +[    0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.570000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.580000] TCP: reno registered
 +[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.600000] NET: Registered protocol family 1
 +[    0.610000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.630000] msgmni has been set to 246
 +[    0.630000] io scheduler noop registered
 +[    0.630000] io scheduler deadline registered (default)
 +[    0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
 +[    0.670000] serial8250.0:​ ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
 +[    0.670000] console [ttyS0] enabled, bootconsole disabled
 +[    0.670000] console [ttyS0] enabled, bootconsole disabled
 +[    0.690000] ath79-spi ath79-spi: master is unqueued, this is deprecated
 +[    0.690000] m25p80 spi0.0: found en25q64, expected m25p80
 +[    0.700000] m25p80 spi0.0: en25q64 (8192 Kbytes)
 +[    0.700000] 5 tp-link partitions found on MTD device spi0.0
 +[    0.710000] Creating 5 MTD partitions on "​spi0.0":​
 +[    0.710000] 0x000000000000-0x000000020000 : "​u-boot"​
 +[    0.720000] 0x000000020000-0x000000118d48 : "​kernel"​
 +[    0.730000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- y
 +[    0.740000] 0x000000118d48-0x0000007f0000 : "​rootfs"​
 +[    0.740000] mtd: partition "​rootfs"​ must either start or end on erase block boundary or be smaller than an erase block -- y
 +[    0.760000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.760000] 1 squashfs-split partitions found on MTD device rootfs
 +[    0.770000] 0x000000330000-0x0000007f0000 : "​rootfs_data"​
 +[    0.780000] 0x0000007f0000-0x000000800000 : "​art"​
 +[    0.780000] 0x000000020000-0x0000007f0000 : "​firmware"​
 +[    0.820000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
 +[    2.080000] libphy: ag71xx_mdio:​ probed
 +[    2.080000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
 +[    2.640000] ag71xx ag71xx.0 eth0: connected to PHY at ag71xx-mdio.0:​00 [uid=004dd034,​ driver=Atheros AR8216/​AR8236/​AR8316]
 +[    2.650000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
 +[    3.210000] TCP: cubic registered
 +[    3.210000] NET: Registered protocol family 17
 +[    3.220000] 8021q: 802.1Q VLAN Support v1.8
 +[    3.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    3.230000] Freeing unused kernel memory: 220K (80319000 - 80350000)
 +Console is alive
 +procd: Console is alive
 +- watchdog -
 +procd: - watchdog -
 +[    5.390000] usbcore: registered new interface driver usbfs
 +[    5.400000] usbcore: registered new interface driver hub
 +[    5.400000] usbcore: registered new device driver usb
 +[    5.410000] ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +[    5.420000] ehci-platform:​ EHCI generic platform driver
 +[    5.420000] ehci-platform ehci-platform.0:​ EHCI Host Controller
 +[    5.430000] ehci-platform ehci-platform.0:​ new USB bus registered, assigned bus number 1
 +[    5.440000] ehci-platform ehci-platform.0:​ TX-TX IDP fix enabled
 +[    5.440000] ehci-platform ehci-platform.0:​ irq 48, io mem 0x1b000000
 +[    5.470000] ehci-platform ehci-platform.0:​ USB 2.0 started, EHCI 1.00
 +[    5.470000] hub 1-0:1.0: USB hub found
 +[    5.480000] hub 1-0:1.0: 1 port detected
 +[    5.480000] ehci-platform ehci-platform.1:​ EHCI Host Controller
 +[    5.490000] ehci-platform ehci-platform.1:​ new USB bus registered, assigned bus number 2
 +[    5.500000] ehci-platform ehci-platform.1:​ TX-TX IDP fix enabled
 +[    5.500000] ehci-platform ehci-platform.1:​ irq 49, io mem 0x1b400000
 +[    5.530000] ehci-platform ehci-platform.1:​ USB 2.0 started, EHCI 1.00
 +[    5.530000] hub 2-0:1.0: USB hub found
 +[    5.540000] hub 2-0:1.0: 1 port detected
 +kmod: ran 19 iterations
 +- preinit -
 +procd: - preinit -
 +Press the [f] key and hit [enter] to enter failsafe mode
 +[    7.660000] eth0: link up (1000Mbps/​Full duplex)
 +mount_root: jffs2 is not ready - marker found
 +[    8.820000] eth0: link down
 +- early -
 +procd: - early -
 +- watchdog -
 +procd: - watchdog -
 +- init -
 +procd: - init -
 +Please press Enter to activate this console.
 +[   ​10.340000] NET: Registered protocol family 10
 +[   ​10.350000] nf_conntrack version 0.5.0 (1977 buckets, 7908 max)
 +[   ​10.360000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​10.380000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
 +[   ​10.390000] Backport generated by backports.git backports-20130617-4-ge3220f5
 +[   ​10.400000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​10.430000] xt_time: kernel timezone is -0000
 +[   ​10.460000] cfg80211: Calling CRDA to update world regulatory domain
 +[   ​10.460000] cfg80211: World regulatory domain updated:
 +[   ​10.470000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[   ​10.480000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.480000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.490000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.500000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.510000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.540000] PPP generic driver version 2.4.2
 +[   ​10.550000] NET: Registered protocol family 24
 +[   ​10.600000] cfg80211: Calling CRDA for country: US
 +[   ​10.600000] cfg80211: Regulatory domain changed to country: US
 +[   ​10.610000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[   ​10.620000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
 +[   ​10.630000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
 +[   ​10.630000] cfg80211: ​  ​(5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.640000] cfg80211: ​  ​(5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.650000] cfg80211: ​  ​(5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​10.660000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
 +[   ​10.670000] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000,​ irq=47
 +[   ​15.540000] eth1: link up (1000Mbps/​Full duplex)
 +[   ​15.540000] device eth1 entered promiscuous mode
 +[   ​15.570000] br-lan: port 1(eth1) entered forwarding state
 +[   ​15.570000] br-lan: port 1(eth1) entered forwarding state
 +[   ​15.600000] IPv6: ADDRCONF(NETDEV_CHANGE):​ eth1: link becomes ready
 +[   ​15.610000] IPv6: ADDRCONF(NETDEV_UP):​ eth0: link is not ready
 +[   ​16.790000] eth0: link up (1000Mbps/​Full duplex)
 +[   ​16.810000] IPv6: ADDRCONF(NETDEV_CHANGE):​ eth0: link becomes ready
 +[   ​17.570000] br-lan: port 1(eth1) entered forwarding state
 +[   ​20.600000] jffs2_scan_eraseblock():​ End of filesystem marker found at 0x0
 +[   ​20.610000] jffs2_build_filesystem():​ unlocking the mtd device... done.
 +[   ​20.610000] jffs2_build_filesystem():​ erasing all blocks after the end marker... done.
 +[   ​40.270000] jffs2: notice: (946) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 0 of xdatum (0 unchecked,.
 +procd: - init complete -
 +
 +
  
-PUT HERE YOUR BOOTLOG+BusyBox v1.19.4 (2013-10-02 19:00:12 MSK) built-in shell (ash) 
 +Enter '​help'​ for a list of built-in commands.
  
 +  _______ ​                    ​________ ​       __
 + ​| ​      ​|.-----.-----.-----.| ​ |  |  |.----.| ​ |_
 + ​| ​  ​- ​  ​|| ​ _  |  -__|     ​|| ​ |  |  ||   ​_|| ​  _|
 + ​|_______|| ​  ​__|_____|__|__||________||__| ​ |____|
 +          |__| W I R E L E S S   F R E E D O M
 + ​-----------------------------------------------------
 + ​BARRIER BREAKER (Bleeding Edge, r38284)
 + ​-----------------------------------------------------
 +  * 1/2 oz Galliano ​        Pour all ingredients into
 +  * 4 oz cold Coffee ​       an irish coffee mug filled
 +  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
 +  * 2 tsp. Creme de Cacao
 + ​-----------------------------------------------------
 +root@OpenWrt:/# ​
 </​code>​ </​code>​
 </p> </p>
 </​HTML>​ </​HTML>​
  
-===== Linux wireless support ===== +OEM GPL Source (v1): [[http://www.tp-link.com/resources/​gpl/​Archer_C7_1.0.tar.gz]] 
-{{http://wireless.kernel.org/en/users/Drivers/ath10k|ath10k}}.+GPL source (v2): http://​www.tp-link.com/resources/gpl/ArcherC7v2_un_gpl.zip
  
 ===== Tags ===== ===== Tags =====
-{{tag>​GigabitEthernet 2NIC 2WNIC 5Port 74Kc 128ram 8flash 2usb ap135 qca9558 qca9880 802.11ac ath10k 802.11n 802.11g 802.11b 802.11a simultan MiniPCIexpress}}+{{tag>​GigabitEthernet 2NIC 2WNIC 5Port 74Kc 128ram 8flash ​16flash ​2usb ap135 qca9558 qca9880 802.11ac ath10k 802.11n 802.11g 802.11b 802.11a simultan MiniPCIexpress}}
toh/tp-link/tl-wdr7500.1373474650.txt.bz2 · Last modified: 2013/07/10 18:44 by lorema