User Tools

Site Tools


toh:tp-link:tl-wr720n

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
toh:tp-link:tl-wr720n [2014/02/26 03:42]
yousong
toh:tp-link:tl-wr720n [2014/09/29 18:00] (current)
liangent
Line 10: Line 10:
 ^ Model Version ^ Launch Date ^ OpenWrt Version Supported ^ Model Specific Notes ^ ^ Model Version ^ Launch Date ^ OpenWrt Version Supported ^ Model Specific Notes ^
 | v3.0 | N/A | [[http://​downloads.openwrt.org/​snapshots/​trunk/​ar71xx/​|trunk]] | Chinese version (rectangular) | | v3.0 | N/A | [[http://​downloads.openwrt.org/​snapshots/​trunk/​ar71xx/​|trunk]] | Chinese version (rectangular) |
 +| v4.0 | N/A | No direct support; firmwares for v3.0 work. | Chinese version (rectangular) |
  
 ===== Features ===== ===== Features =====
Line 25: Line 26:
 As from 28 April 2013, support for the TL-WR720N is present in the Trunk version of OpenWrt, see this [[https://​forum.openwrt.org/​viewtopic.php?​id=37912&​p=3|thread on the forum]] for further reference. As from 28 April 2013, support for the TL-WR720N is present in the Trunk version of OpenWrt, see this [[https://​forum.openwrt.org/​viewtopic.php?​id=37912&​p=3|thread on the forum]] for further reference.
  
-===== Failsafe mode =====+==== v4.0 notes ====
  
-For trunk version after [[https://​dev.openwrt.org/​browser/?​rev=39752|r39752]],​ generic failsafe mode howto [[doc:​howto:​generic.failsafe]] can be used.+The hardware of v4.0 is almost the same as v3.0 so firmwares for v3.0 just work. The version number in images for v4.0 is 0x07200104 (0x07200103 for v3.0).
  
-For Attitude Adjustment version of OpenWrt:+==== USB ports ====
  
-  - At boot time, when SYS led started to blink, click the RESET button. +It appears ​the hardware switch must be set to "​3G"​ to make the USB port workOtherwise ​the port has power output but devices connected can'​t ​be detected by OpenWrt.
-  - Then SYS led would blink a lot faster. +
-  - Shell access can be achieved through telnet with a network cable connected ​to the port which should be labeled as WAN (as of revision r37374). +
-  - From there, follow ​the generic failsafe mode instructions should ​be fine.+
  
-There is a patch for TL-WR720N-v3 to [[http://patchwork.openwrt.org/​patch/​4021/​|make ​failsafe ​work on LAN port]].+==== Failsafe mode ==== 
 +-[[doc:howto:​generic.failsafe]]
  
-==== Internal Pictures ==== +Note that the **mount_root** command will not work(You can use the [[doc:howto:​generic.sysupgrade#​netcat|netcat method]] to install a fresh copy of the system if necessary.)
- +
-{{:​media:​tl-wr720n001.jpg|}} +
- +
-{{:​media:​tl-wr720n002.jpg|}} +
- +
-{{:​media:​tl-wr720n003.jpg|}} +
- +
-{{:​media:​tl-wr720n004.jpg|}} +
- +
-{{:​media:​tl-wr720n005.jpg|}} +
- +
-{{:​media:​tl-wr720n009.jpg|}} +
- +
-{{:​media:​tl-wr720n012.jpg|}} +
- +
-{{:​media:​tl-wr720n013.jpg|}} +
- +
-{{:​media:​tl-wr720n015.jpg|}} +
- +
-{{:​media:​tl-wr720n017.jpg|}} +
- +
-With thanks to mveplus who posted these pictures in the [[https://forum.openwrt.org/​viewtopic.php?​id=37912|forum thread]].+
  
 ==== Serial Console ==== ==== Serial Console ====
toh/tp-link/tl-wr720n.1393382558.txt.bz2 · Last modified: 2014/02/26 03:42 by yousong