User Tools

Site Tools


toh:trendnet:trendnet_tew-810dr_1.0_1.1

Trendnet TEW-810DR

Board are similar to dlink dir-810l. Image from dir-810l are working. 2.4Ghz radio working. 5Ghz radio not working.

Installation

Use image for dlink dir-810.

Image ID should be modyfied by this command (see dir-810 page) : ncc_att_hwid -f dir-810-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"

Flash Layout

# cat /proc/mtd dev: size erasesize name mtd0: 00800000 00010000 "ALL" mtd1: 00030000 00010000 "Bootloader" mtd2: 00010000 00010000 "Config" mtd3: 00010000 00010000 "Factory" mtd4: 00010000 00010000 "5G_RF" mtd5: 00010000 00010000 "Wolf_Config" mtd6: 00080000 00010000 "MyDLink" mtd7: 00080000 00010000 "Jffs2" mtd8: 000f8ebc 00010000 "Kernel" mtd9: 00597144 00010000 "RootFS"

PCB photos

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

same as dlink dir-810l

Serial connection parameters
for Trendnet tew-810dr 1.0,1.1
57600, 8N1

Bootloader mods

Hardware mods

USB mod looks possible.

Bootlogs

OEM bootlog

This is HW 1.0R bootlog: U-Boot 1.1.3 (Jan 17 2013 - 10: 14:35) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83f98000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 29 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D MAC: d8:eb:97:22:12:21 ============================================ Ralink UBoot Version: 4.1.1.0 TEW-810DR(1.00b02) -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Jan 17 2013 Time:10:14:35 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes You choosed 3 3: System Boot system code via Flash. ## Booting image at bc170000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5766780 Bytes = 5.5 MB Load Address: 80000000 Entry Point: 8000c2d0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c2d0) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC init started: BusyBox v1.12.1 (2013-10-15 17:53:03 CST) starting pid 35, tty '': '/etc_ro/rcS' mount: mounting none on /proc/bus/usb failed: No such file or directory Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= mount mydlink ok mount flash ok old language pack not found language pack exists Starting loop GPIO LED=9,PBC=2 [ leobox_ipc.c: 207 sem_create()]:::add semid = 0 [ leobox_ipc.c: 207 sem_create()]:::add semid = 32769 [ leobox_ipc.c: 207 sem_create()]:::add semid = 65538 [ leobox_ipc.c: 207 sem_create()]:::add semid = 98307 [ leobox_ipc.c: 207 sem_create()]:::add semid = 131076 [ leobox_ipc.c: 207 sem_create()]:::add semid = 163845 [ leobox_ipc.c: 207 sem_create()]:::add semid = 196614 [ leobox_ipc.c: 207 sem_create()]:::add semid = 229383 [ leobox_ipc.c: 207 sem_create()]:::add semid = 262152 [ leobox_ipc.c: 207 sem_create()]:::add semid = 294921 [ leobox_ipc.c: 207 sem_create()]:::add semid = 327690 [ leobox_ipc.c: 207 sem_create()]:::add semid = 360459 [ leobox_ipc.c: 207 sem_create()]:::add semid = 393228 [ leobox_ipc.c: 207 sem_create()]:::add semid = 425997 [ leobox_ipc.c: 207 sem_create()]:::add semid = 458766 [ leobox_ipc.c: 207 sem_create()]:::add semid = 491535 [ leobox_ipc.c: 207 sem_create()]:::add semid = 524304 [ leobox_ipc.c: 207 sem_create()]:::add semid = 557073 [ leobox_ipc.c: 207 sem_create()]:::add semid = 589842 [ leobox_ipc.c: 207 sem_create()]:::add semid = 622611 [ leobox_ipc.c: 207 sem_create()]:::add semid = 655380 [ 123 ncc_main.c : 177 main()]:::[123]Thread Create[main thread] [ 123 ncc_runtimecfg.c : 480 initRunTimeCfg()]:::Init Run-Time Config Success. [ 123 ncc_runtimecfg.c : 481 initRunTimeCfg()]:::Total 8091 nodes, each node 24 bytes. [ 123 ncc_runtimecfg.c : 482 initRunTimeCfg()]:::Total 194184 byte for all nodes. [ 123 ncc_runtimecfg.c : 483 initRunTimeCfg()]:::Total 115849 byte for data. [ 123 ncc_runtimecfg.c : 182 loadCfg()]:::Start loadCfg Waiting for Wireless Events from interfaces... [ 123 ncc_lz77.c : 534 flash2rootfs()]:::Load Success(/var/tmp/cfg.txt) [ 123 ncc_inf.c : 605 ncc_inf_main()]:::JTraceLevel=4 [ 123 leobox_network.c : 1064 socket_select()]:::Enter pid=123,ppid=1 [leobox_network.c: 1074 socket_select()]:::main process get thread id=1026 [ 143 leobox_network.c : 816 socket_select_hdlr()]:::[143]Thread Create[socket_select_hdlr] [ 144 ncc_inf.c : 432 processInf()]:::[144]Thread Create[processInf] starting pid 148, tty '/dev/ttyS1': '/bin/sh' ================nice=-20 # bind: Address already in use [ 123 ncc_main.c : 269 main()]:::Stop Web Access HTTP [ 123 ncc_httpd.c : 539 httpdOp()]:::st is null. [ 123 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/../model/tew_813dr/objTools/ncc_objTools.c: 6265 probeHTTPsEnable()]:::probeHTTPsEnable(); [ 123 ncc_main.c : 291 main()]:::Start HTTPS mini_httpd: started as root without requesting chroot(), warning only bind: Address already in use mini_httpd: started as root without requesting chroot(), warning only [ 123 ncc_main.c : 305 main()]:::Stop Web Access HTTPS [ 123 ncc_httpd.c : 539 httpdOp()]:::st is null. [ 159 leobox_timer.c : 248 timerThread()]:::[159]Thread Create[timerThread] [ 159 leobox_timer.c : 256 timerThread()]:::Timer Thread Running [ 160 ncc_main.c : 41 sendBootEvent()]:::[160]Thread Create[sendBootEvent] sh: cannot create /proc/sys/net/ipv4/conf/eth2.2/arp_ignore: nonexistent directory [ 123 ncc_fsm_boot.c : 490 Boot()]:::=====================Start TEW_810DR_Boot===================== [ 123 ncc_fsm_boot.c : 553 Boot()]:::MAC 0 = D8EB97111111 [ 123 ncc_fsm_boot.c : 554 Boot()]:::MAC 1 = D8EB97111111 switch reg write offset=3100, value=56330 switch reg write offset=3200, value=56330 switch reg write offset=3300, value=56330 switch reg write offset=3400, value=56330 switch reg write offset=3000, value=56330 Set: phy[4].reg[4] = 05e1 Set: phy[4].reg[0] = 3300 [ 123 ncc_l2_independence.c: 171 swSpeedSet()]:::port = 4, speed = 0 killall: crond: no process killed [ 123 ncc_crond.c : 54 crondConf()]:::DEBUG ON [ 123 ncc_firewall.c : 1550 reBuildMAC6()]:::reBuildMAC6()+ [ 123 ncc_firewall.c : 1596 reBuildMAC6()]:::reBuildMAC6()- ip6tables: No chain/target/match by that name. killall: wakeOnLanProxy: no process killed [ 123 ncc_firewall.c : 4938 runFwScript()]:::===ipt run start=== [ 123 ncc_firewall.c : 4940 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 5532 nfOpFunc()]:::[nfOpFunc]Finish nf_init, 0 [ 123 ncc_fsm_boot.c : 763 Boot()]:::cfg->tzone=-128 Sat Jan 1 00:00:00 GMT 2011 [ 123 ncc_fsm_boot.c : 789 Boot()]:::Merge language pack!! [ 4215 lang_merge.c : 1153 main()]:::before print info [ 4215 lang_merge.c : 1156 main()]:::Parameters: ori_lang_fp: /var/tmp/lang.js def_lang_fp: /www/def_lang.js [ 4215 lang_merge.c : 1234 main()]:::save to old js file!! [ 4215 lang_merge.c : 1235 main()]:::save to old js file!! [ 4215 lang_merge.c : 1236 main()]:::save to old js file!! sh: cannot create /proc/sys/net/ipv6/conf/ra1/disable_ipv6: nonexistent directory sh: cannot create /proc/sys/net/ipv6/conf/rai1/disable_ipv6: nonexistent directory [ 123 ncc_routerlan.c : 37 attachWanDomainName()]:::Get wan interface fail!! [ 123 ncc_routerlan.c : 37 attachWanDomainName()]:::Get wan interface fail!! [ 123 ncc_help.c : 1572 checkDefCfg()]:::defCfg=1 llmnr: have no available linklocal address. wait count=0 [ 123 ncc_firewall.c : 4938 runFwScript()]:::===ipt run start=== [ 123 ncc_firewall.c : 4940 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 5532 nfOpFunc()]:::[nfOpFunc]Finish nf_redirect_to_index_on, 47 [ 123 ncc_firewall.c : 4938 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=1 [ 123 ncc_firewall.c : 4940 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 5532 nfOpFunc()]:::[nfOpFunc]Finish nf_lan_up, 3 [ 123 ncc_help.c : 1572 checkDefCfg()]:::defCfg=1 invalid option in file /var/tmp/upnpd_wan.conf line 2 : int_ifname=br0 invalid option in file /var/tmp/upnpd_wan.conf line 14 : wps_enable=1 Jan 1 00:00:06 miniupnpd[5964]: could not open lease file: /tmp/upnp_rdr_list Jan 1 00:00:06 miniupnpd[5964]: HTTP listening on port 65530 No IPv6 address found for interface br0. Jan 1 00:00:06 miniupnpd[5964]: no HTTP IPv6 address Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m Jan 1 00:00:06 miniupnpd[5964]: [truncated] m mDNSResponderPosix: Starting in daemon mode killall: lld2d: no process killed llmnr: have no available linklocal address. wait count=2 ***** g_wl_interface = ra0 ****** killall: proxy: no process killed [ leobox_ipc.c: 207 sem_create()]:::add semid = 688149 [ 5981 lanmapd.c : 2647 main()]:::=============================Lanmapd============================= [ 5981 lanmapd.c : 2648 main()]:::iface br0 [ 5981 lanmapd.c : 2649 main()]:::ip 192.168.10.1 [ 5981 lanmapd.c : 2653 main()]:::netmask 255.255.255.0 [ 5981 lanmapd.c : 2654 main()]:::network id 192.168.10.0 [ 5981 lanmapd.c : 2655 main()]:::mac d8:eb:97:11:11:11 [ 5981 lanmapd.c : 2656 main()]:::hostname TEW-810DR [ 5981 lanmapd.c : 2657 main()]:::hostname encode FEEFFHCNDIDBDAEEFCCACACACAAAAAAA [ 5981 lanmapd.c : 2662 main()]:::================================================================= killall: crond: no process killed llmnr: have no available linklocal address. wait count=3 [ 123 ncc_fsm_boot.c : 284 doRtInit()]:::Run 5G probe Wlan ! killall: wscd: no process killed [ 123 ncc_fsm_boot.c : 293 doRtInit()]:::Run 2G probe Wlan ! Starting loop GPIO LED=9,PBC=2 [ 123 ncc_fsm_boot.c : 299 doRtInit()]:::Send Event to open 2.4G Wlan ! [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=4 llmnr: have no available linklocal address. wait count=5 llmnr: have no available linklocal address. wait count=6 llmnr: have no available linklocal address. wait count=7 llmnr: have no available linklocal address. wait count=8 llmnr: have no available linklocal address. wait count=9 [ 123 ncc_mt7620_wlan.c : 1431 wlanOnOff()]:::=> bug on what happen rai1 down ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device [ 123 ncc_fsm_boot.c : 302 doRtInit()]:::Send Event to open 5G Wlan ! [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=10 llmnr: have no available linklocal address. wait count=11 llmnr: have no available linklocal address. wait count=12 [ 123 ncc_mt7620_wlan.c : 1431 wlanOnOff()]:::=> bug on what happen rai1 down llmnr: have no available linklocal address. wait count=13 Starting loop GPIO LED=9,PBC=2 brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy killall: wscd: no process killed Starting loop GPIO LED=9,PBC=2 route: ioctl 0x890b failed: File exists brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy [ 123 ncc_fsm_boot.c : 906 Boot()]:::wanCableLink = 0 libupnp: using UDP SSDP_PORT = 1900 [ 123 ncc_help.c : 1572 checkDefCfg()]:::defCfg=1 mDNSResponderPosix: Starting in daemon mode [ 123 ncc_dev_independence.c: 3773 devOpFunc()]:::get internet_cable_lose [ 123 ncc_firewall.c : 4938 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=14 [ 123 ncc_firewall.c : 4940 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 5532 nfOpFunc()]:::[nfOpFunc]Finish nf_80_to_404_on, 38 ip6tables: Bad rule (does a matching rule exist in that chain?). llmnr: have no available linklocal address. wait count=15 [ 123 ncc_help.c : 1925 is_v6defaultgw_exist()]:::[IPv6 WARNING] Default GW not Exist. [ 123 ncc_radvd.c : 233 radvdConf()]:::is6rdsunset: 0, prefix: [ 123 ncc_fsm_boot.c : 1283 Boot()]:::setting v6Lan Host Filter=fe80:0:0:0:daeb:97ff:1111:1111! [ 123 ncc_fsm_boot.c : 1305 Boot()]:::=====================finish TEW_810DR_Boot===================== [SYS][ 123 ncc_fsm_boot.c : 1324 Boot()]:::Boot Complate!! [ 123 ncc_EventInternal.c : 1156 doEventInternal()]:::InternalLocalTimeChange [ 123 ncc_EventInternal.c : 499 onMailSchedule()]:::mailCfg.schedSendEnable ? 0 [ 123 ncc_EventInternal.c : 1175 doEventInternal()]:::needSendLog = 0 [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 251 wlanSchedCheck()]:::no sched # cat /proc/mtd dev: size erasesize name mtd0: 00800000 00010000 "ALL" mtd1: 00030000 00010000 "Bootloader" mtd2: 00010000 00010000 "Config" mtd3: 00010000 00010000 "Factory" mtd4: 00010000 00010000 "5G_RF" mtd5: 00010000 00010000 "Wolf_Config" mtd6: 00080000 00010000 "MyDLink" mtd7: 00080000 00010000 "Jffs2" mtd8: 000f8ebc 00010000 "Kernel" mtd9: 00597144 00010000 "RootFS" # cat /cat /proc/cpuinfo cat: can't open '/cat': No such file or directory system type : Ralink SoC processor : 0 cpu model : MIPS 24Kc V5.0 BogoMIPS : 386.04 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0004, 0x0ffc, 0x0ff8, 0x0ffb] ASEs implemented : mips16 dsp shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available This is HW 1.1R bootlog:

U-Boot 1.1.3 (Jan 17 2013 - 10:14:35) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83f98000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. spi_wait_nsec: 29 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D MAC: d8:eb:97:11:11:11 ============================================ Ralink UBoot Version: 4.1.1.0 TEW-810DR(1.00b02) -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Jan 17 2013 Time:10:14:35 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc170000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5748149 Bytes = 5.5 MB Load Address: 80000000 Entry Point: 8000c2d0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c2d0) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC init started: BusyBox v1.12.1 (2014-09-29 18:45:32 CST) starting pid 35, tty '': '/etc_ro/rcS' mount: mounting none on /proc/bus/usb failed: No such file or directory Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= mount mydlink ok mount flash ok old language pack not found language pack exists Starting loop GPIO LED=9,PBC=2 [ leobox_ipc.c: 207 sem_create()]:::add semid = 0 [ leobox_ipc.c: 207 sem_create()]:::add semid = 32769 [ leobox_ipc.c: 207 sem_create()]:::add semid = 65538 [ leobox_ipc.c: 207 sem_create()]:::add semid = 98307 [ leobox_ipc.c: 207 sem_create()]:::add semid = 131076 [ leobox_ipc.c: 207 sem_create()]:::add semid = 163845 [ leobox_ipc.c: 207 sem_create()]:::add semid = 196614 [ leobox_ipc.c: 207 sem_create()]:::add semid = 229383 [ leobox_ipc.c: 207 sem_create()]:::add semid = 262152 [ leobox_ipc.c: 207 sem_create()]:::add semid = 294921 [ leobox_ipc.c: 207 sem_create()]:::add semid = 327690 [ leobox_ipc.c: 207 sem_create()]:::add semid = 360459 [ leobox_ipc.c: 207 sem_create()]:::add semid = 393228 [ leobox_ipc.c: 207 sem_create()]:::add semid = 425997 [ leobox_ipc.c: 207 sem_create()]:::add semid = 458766 [ leobox_ipc.c: 207 sem_create()]:::add semid = 491535 [ leobox_ipc.c: 207 sem_create()]:::add semid = 524304 [ leobox_ipc.c: 207 sem_create()]:::add semid = 557073 [ leobox_ipc.c: 207 sem_create()]:::add semid = 589842 [ leobox_ipc.c: 207 sem_create()]:::add semid = 622611 [ leobox_ipc.c: 207 sem_create()]:::add semid = 655380 [ 123 ncc_main.c : 178 main()]:::[123]Thread Create[main thread] Waiting for Wireless Events from interfaces... [ 123 ncc_runtimecfg.c : 539 initRunTimeCfg()]:::Init Run-Time Config Success. [ 123 ncc_runtimecfg.c : 540 initRunTimeCfg()]:::Total 8091 nodes, each node 24 bytes. [ 123 ncc_runtimecfg.c : 541 initRunTimeCfg()]:::Total 194184 byte for all nodes. [ 123 ncc_runtimecfg.c : 542 initRunTimeCfg()]:::Total 115849 byte for data. [ 123 ncc_runtimecfg.c : 207 loadCfg()]:::Start loadCfg /etc_ro/rcS: line 164: mp.sh: not found starting pid 141, tty '/dev/ttyS1': '/bin/sh' ================nice=-20 # [ 123 ncc_lz77.c : 534 flash2rootfs()]:::Load Success(/var/tmp/cfg.txt) [ 123 ncc_inf.c : 1135 ncc_inf_main()]:::JTraceLevel=4 [ 123 leobox_network.c : 1083 socket_select()]:::Enter pid=123,ppid=1 [ 145 leobox_network.c : 835 socket_select_hdlr()]:::[145]Thread Create[socket_select_hdlr] [leobox_network.c: 1093 socket_select()]:::main process get thread id=1026 [ 146 ncc_inf.c : 962 processInf()]:::[146]Thread Create[processInf] bind: Address already in use [ 123 ncc_main.c : 273 main()]:::Stop Web Access HTTP [ 123 ncc_httpd.c : 539 httpdOp()]:::st is null. [ 123 /opt/release/rt6856/RT288x_SDK/source/user/wolf/cameo/ncc/../model/tew_813dr/objTools/ncc_objTools.c: 6307 probeHTTPsEnable()]:::probeHTTPsEnable(); [ 123 ncc_main.c : 294 main()]:::Start HTTPS mini_httpd: started as root without requesting chroot(), warning only bind: Address already in use [ 123 ncc_main.c : 308 main()]:::Stop Web Access HTTPS [ 123 ncc_httpd.c : 539 httpdOp()]:::st is null. mini_httpd: started as root without requesting chroot(), warning only [ 157 leobox_timer.c : 235 timerThread()]:::[157]Thread Create[timerThread] [ 157 leobox_timer.c : 243 timerThread()]:::Timer Thread Running [ 158 ncc_main.c : 42 sendBootEvent()]:::[158]Thread Create[sendBootEvent] sh: cannot create /proc/sys/net/ipv4/conf/eth2.2/arp_ignore: nonexistent directory [ 123 ncc_fsm_boot.c : 490 Boot()]:::=====================Start TEW_810DR_Boot===================== [ 123 ncc_fsm_boot.c : 553 Boot()]:::MAC 0 = D8EB97111111 [ 123 ncc_fsm_boot.c : 554 Boot()]:::MAC 1 = D8EB97111111 switch reg write offset=3100, value=56330 switch reg write offset=3200, value=56330 switch reg write offset=3300, value=56330 switch reg write offset=3400, value=56330 switch reg write offset=3000, value=56330 Set: phy[4].reg[4] = 05e1 Set: phy[4].reg[0] = 3300 [ 123 ncc_l2_independence.c: 171 swSpeedSet()]:::port = 4, speed = 0 killall: crond: no process killed [ 123 ncc_crond.c : 54 crondConf()]:::DEBUG ON REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [ 123 ncc_firewall.c : 1634 reBuildMAC6()]:::reBuildMAC6()+ REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [ 123 ncc_firewall.c : 1683 reBuildMAC6()]:::reBuildMAC6()- ip6tables: No chain/target/match by that name. killall: wakeOnLanProxy: no process killed [ 123 ncc_firewall.c : 5392 runFwScript()]:::===ipt run start=== [ 123 ncc_firewall.c : 5394 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 6005 nfOpFunc()]:::[nfOpFunc]Finish nf_init, 0 [ 123 ncc_fsm_boot.c : 763 Boot()]:::cfg->tzone=-128 Sat Jan 1 00:00:00 GMT 2011 [ 123 ncc_fsm_boot.c : 789 Boot()]:::Merge language pack!! [ 4376 lang_merge.c : 1153 main()]:::before print info [ 4376 lang_merge.c : 1156 main()]:::Parameters: ori_lang_fp: /var/tmp/lang.js def_lang_fp: /www/def_lang.js [ 4376 lang_merge.c : 1234 main()]:::save to old js file!! [ 4376 lang_merge.c : 1235 main()]:::save to old js file!! [ 4376 lang_merge.c : 1236 main()]:::save to old js file!! sh: cannot create /proc/sys/net/ipv6/conf/ra1/disable_ipv6: nonexistent directory sh: cannot create /proc/sys/net/ipv6/conf/rai1/disable_ipv6: nonexistent directory [ 123 ncc_routerlan.c : 37 attachWanDomainName()]:::Get wan interface fail!! [ 123 ncc_routerlan.c : 37 attachWanDomainName()]:::Get wan interface fail!! [ 123 ncc_help.c : 1599 checkDefCfg()]:::defCfg=1 llmnr: have no available linklocal address. wait count=0 [ 123 ncc_firewall.c : 5392 runFwScript()]:::===ipt run start=== [ 123 ncc_firewall.c : 5394 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 6005 nfOpFunc()]:::[nfOpFunc]Finish nf_redirect_to_index_on, 47 [ 123 ncc_firewall.c : 5392 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=1 [ 123 ncc_firewall.c : 5394 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 6005 nfOpFunc()]:::[nfOpFunc]Finish nf_lan_up, 3 [ 123 ncc_help.c : 1599 checkDefCfg()]:::defCfg=1 llmnr: have no available linklocal address. wait count=2 invalid option in file /var/tmp/upnpd_wan.conf line 2 : int_ifname=br0 invalid option in file /var/tmp/upnpd_wan.conf line 14 : wps_enable=1 Jan 1 00:00:07 miniupnpd[6381]: could not open lease file: /tmp/upnp_rdr_list Jan 1 00:00:07 miniupnpd[6381]: HTTP listening on port 65530 No IPv6 address found for interface br0. Jan 1 00:00:07 miniupnpd[6381]: no HTTP IPv6 address Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m Jan 1 00:00:07 miniupnpd[6381]: [truncated] m mDNSResponderPosix: Starting in daemon mode killall: lld2d: no process killed ***** g_wl_interface = ra0 ****** killall: proxy: no process killed [ leobox_ipc.c: 207 sem_create()]:::add semid = 688149 [ 6398 lanmapd.c : 2648 main()]:::=============================Lanmapd============================= [ 6398 lanmapd.c : 2649 main()]:::iface br0 [ 6398 lanmapd.c : 2650 main()]:::ip 192.168.10.1 [ 6398 lanmapd.c : 2654 main()]:::netmask 255.255.255.0 [ 6398 lanmapd.c : 2655 main()]:::network id 192.168.10.0 [ 6398 lanmapd.c : 2656 main()]:::mac d8:eb:97:11:11:11 [ 6398 lanmapd.c : 2657 main()]:::hostname TEW-810DR [ 6398 lanmapd.c : 2658 main()]:::hostname encode FEEFFHCNDIDBDAEEFCCACACACAAAAAAA [ 6398 lanmapd.c : 2663 main()]:::================================================================= llmnr: have no available linklocal address. wait count=3 killall: crond: no process killed [ 123 ncc_fsm_boot.c : 284 doRtInit()]:::Run 5G probe Wlan ! killall: wscd: no process killed [ 123 ncc_fsm_boot.c : 293 doRtInit()]:::Run 2G probe Wlan ! Starting loop GPIO LED=9,PBC=2 [ 123 ncc_fsm_boot.c : 299 doRtInit()]:::Send Event to open 2.4G Wlan ! [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=4 llmnr: have no available linklocal address. wait count=5 llmnr: have no available linklocal address. wait count=6 llmnr: have no available linklocal address. wait count=7 llmnr: have no available linklocal address. wait count=8 llmnr: have no available linklocal address. wait count=9 [ 123 ncc_mt7620_wlan.c : 1412 wlanOnOff()]:::=> bug on what happen rai1 down ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device [ 123 ncc_fsm_boot.c : 302 doRtInit()]:::Send Event to open 5G Wlan ! [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched llmnr: have no available linklocal address. wait count=10 llmnr: have no available linklocal address. wait count=11 llmnr: have no available linklocal address. wait count=12 [ 123 ncc_mt7620_wlan.c : 1412 wlanOnOff()]:::=> bug on what happen rai1 down llmnr: have no available linklocal address. wait count=13 Starting loop GPIO LED=9,PBC=2 brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy killall: wscd: no process killed brctl: bridge br0: Device or resource busy Starting loop GPIO LED=9,PBC=2 brctl: bridge br0: Device or resource busy route: ioctl 0x890b failed: File exists brctl: bridge br0: Device or resource busy brctl: bridge br0: Device or resource busy [ 123 ncc_fsm_boot.c : 906 Boot()]:::wanCableLink = 0 libupnp: using UDP SSDP_PORT = 1900 [ 123 ncc_help.c : 1599 checkDefCfg()]:::defCfg=1 mDNSResponderPosix: Starting in daemon mode [ 123 ncc_dev_independence.c: 3790 devOpFunc()]:::get internet_cable_lose [ 123 ncc_firewall.c : 5392 runFwScript()]:::===ipt run start=== llmnr: have no available linklocal address. wait count=14 [ 123 ncc_firewall.c : 5394 runFwScript()]:::===ipt run end=== [SYS][ 123 ncc_firewall.c : 6005 nfOpFunc()]:::[nfOpFunc]Finish nf_80_to_404_on, 38 ip6tables: Bad rule (does a matching rule exist in that chain?). [ 123 ncc_help.c : 1952 is_v6defaultgw_exist()]:::[IPv6 WARNING] Default GW not Exist. [ 123 ncc_radvd.c : 233 radvdConf()]:::is6rdsunset: 0, prefix: [ 123 ncc_fsm_boot.c : 1283 Boot()]:::setting v6Lan Host Filter=fe80:0:0:0:daeb:97ff:1111:1111! [ 123 ncc_fsm_boot.c : 1305 Boot()]:::=====================finish TEW_810DR_Boot===================== [SYS][ 123 ncc_fsm_boot.c : 1324 Boot()]:::Boot Complate!! [Type]0x0001[Length]9[Value]TEW-810DR [Type]0x0002[Length]4[Value]1.0R [Type]0x0003[Length]2[Value]WW [Type]0x0004[Length]1[Value]1 [Type]0x0005[Length]7[Value]1.10b02 [Type]0x0006[Length]1[Value]1 [Type]0x0007[Length]7[Value]0.00b00 [Type]0x0008[Length]17[Value]D8:EB:97:2C:11:11 [Type]0x0009[Length]17[Value]D8:EB:97:2C:11:11 [Type]0x000A[Length]17[Value]D8:EB:97:2C:11:11 [Type]0x000B[Length]17[Value]D8:EB:97:2C:11:11 [Type]0x000C[Length]4[Value]0x10 [Type]0x0010[Length]23[Value]TRENDnet810_2.4GHz_53LN [Type]0x0011[Length]21[Value]TRENDnet810_5GHz_53LN [Type]0x0012[Length]11[Value]81031001427 [Type]0x0014[Length]10[Value]0xFEDD1B5C [Type]0x0015[Length]8[Value]19131481 [ 123 ncc_EventInternal.c : 1272 doEventInternal()]:::InternalLocalTimeChange [ 123 ncc_EventInternal.c : 584 onMailSchedule()]:::mailCfg.schedSendEnable ? 0 [ 123 ncc_EventInternal.c : 1291 doEventInternal()]:::needSendLog = 0 [ 123 ncc_objAction.c : 2304 ResetWirelessCounter()]:::DEBUG ON[ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched cat: can't open '/var/run/wscd.pid.rai0': No such file or directory kill: you need to specify whom to kill rm: cannot remove '/var/run/wscd.pid.rai0': No such file or directory libupnp: using UDP SSDP_PORT = 1900 [ 123 ncc_mt7620_wlan.c : 1412 wlanOnOff()]:::=> bug on what happen rai1 down Starting loop GPIO LED=9,PBC=2 route: ioctl 0x890b failed: File exists invalid option in file /var/tmp/upnpd_wan.conf line 2 : int_ifname=br0 invalid option in file /var/tmp/upnpd_wan.conf line 14 : wps_enable=1 libupnp: using UDP SSDP_PORT = 1900 [ 123 ncc_objAction.c : 2320 ResetWirelessCounter()]:::DEBUG ON[ 123 ncc_mt7620_wlan.c : 1412 wlanOnOff()]:::=> bug on what happen rai1 down [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_mt7620_wlan.c : 1412 wlanOnOff()]:::=> bug on what happen rai1 down Starting loop GPIO LED=9,PBC=2 route: ioctl 0x890b failed: File exists invalid option in file /var/tmp/upnpd_wan.conf line 2 : int_ifname=br0 invalid option in file /var/tmp/upnpd_wan.conf line 14 : wps_enable=1 [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched [ 123 ncc_EventInternal.c : 335 wlanSchedCheck()]:::no sched # cat /proc/cpu cat: can't open '/proc/cpu': No such file or directory # cat /proc/cpuinfo system type : Ralink SoC processor : 0 cpu model : MIPS 24Kc V5.0 BogoMIPS : 386.04 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes, count: 4, address/irw mask: [0x0ff8, 0x0ff8, 0x0bfb, 0x0ff8] ASEs implemented : mips16 dsp shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available # cat /proc/mtd dev: size erasesize name mtd0: 00800000 00010000 "ALL" mtd1: 00030000 00010000 "Bootloader" mtd2: 00010000 00010000 "Config" mtd3: 00010000 00010000 "Factory" mtd4: 00010000 00010000 "5G_RF" mtd5: 00010000 00010000 "Wolf_Config" mtd6: 00080000 00010000 "MyDLink" mtd7: 00080000 00010000 "Jffs2" mtd8: 000f95f5 00010000 "Kernel" mtd9: 00596a0b 00010000 "RootFS" mtd10: 00690000 00010000 "Kernel_RootFS" # dmesg /bin/sh: dmesg: not found # cat /var/log/messages Jan 1 00:00:08 TEW-810DR syslog.info syslogd started: BusyBox v1.12.1 Jan 1 00:00:08 TEW-810DR user.info Wireless[6477]: WPS polling daemon start Jan 1 00:00:19 TEW-810DR user.info Wireless[6544]: WPS polling daemon start Jan 1 00:00:20 TEW-810DR user.info Wireless[6586]: WPS polling daemon start Jan 1 00:00:20 TEW-810DR user.warn ncc[123]: [ltAttacks][nfOpFunc]Finish nf_80_to_404_on, 38 Jan 1 00:00:22 TEW-810DR user.info ncc[123]: [ltSystemActivity]Boot Complate!! Jan 1 00:00:30 TEW-810DR user.info Wireless[6925]: WPS polling daemon start Jan 1 00:00:30 TEW-810DR daemon.notice miniupnpd[6943]: HTTP listening on port 65530 Jan 1 00:00:30 TEW-810DR daemon.notice miniupnpd[6943]: HTTP IPv6 address given to control points : [fe80:0000:0000:0000:daeb:97ff:1111:1111] Jan 1 00:00:35 TEW-810DR user.info Wireless[7052]: WPS polling daemon start Jan 1 00:00:35 TEW-810DR daemon.notice miniupnpd[7068]: HTTP listening on port 65530 Jan 1 00:00:35 TEW-810DR daemon.notice miniupnpd[7068]: HTTP IPv6 address given to control points : [fe80:0000:0000:0000:daeb:97ff:1111:1111] # ps ax PID USER VSZ STAT COMMAND 1 root 2220 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW< [khelper] 7 root 0 SW [sync_supers] 8 root 0 SW [bdi-default] 9 root 0 SW< [kblockd] 10 root 0 SW [kswapd0] 11 root 0 SW< [crypto] 15 root 0 SW [mtdblock0] 16 root 0 SW [mtdblock1] 17 root 0 SW [mtdblock2] 18 root 0 SW [mtdblock3] 19 root 0 SW [mtdblock4] 20 root 0 SW [mtdblock5] 21 root 0 SW [mtdblock6] 22 root 0 SW [mtdblock7] 23 root 0 SW [mtdblock8] 24 root 0 SW [mtdblock9] 25 root 0 SW [mtdblock10] 26 root 0 SW [kworker/u:1] 33 root 0 SW [kworker/0:1] 41 root 0 SWN [jffs2_gcd_mtd6] 43 root 0 SWN [jffs2_gcd_mtd7] 119 root 1104 S resetd 120 root 1416 S iwevent 123 root 5532 S ncc 141 root 2220 S /bin/sh 143 root 1116 S < watchdog 144 root 5532 S ncc 145 root 5532 S ncc 146 root 5532 S ncc 151 root 4520 S < mini_httpd -M 0 -C /var/tmp/mini_httpd_0.conf 155 root 4560 S < mini_httpd -M 0 -C /var/tmp/mini_httpd_1.conf -S -E / 157 root 5532 S ncc 159 root 0 SW [flush-mtd-unmap] 4404 root 1520 S udhcpd /var/tmp/udhcpd-br0.conf 4405 root 1520 S udhcpd /var/tmp/udhcpd-br0.conf 4406 root 1520 S udhcpd /var/tmp/udhcpd-br0.conf 4420 root 1224 S dnsmasq -o -u root -i br0 -z br0 -a 192.168.10.1 -x / 4421 root 1124 S llmnr br0 TEW-810DR d8:eb:97:11:11:11 6397 root 1260 S lld2d br0 6398 root 2212 S lanmapd br0 6400 root 2212 S lanmapd br0 6401 root 2456 S proxy br0 54088 0 /var/tmp/proxy.conf 6402 root 2212 S lanmapd br0 6403 root 2460 S < proxy br0 54088 0 /var/tmp/proxy.conf 6416 root 2216 S syslogd -L -s 16 6418 root 2216 S syslogd -L -s 16 6503 root 0 SW [kworker/0:2] 6635 root 1524 S mDNSResponderPosix -f /var/tmp/mdns.conf -b -P /var/r 6744 root 1208 S radvd -C /var/tmp/radvd_br0.conf -p /var/run/radvd_br 6878 root 0 SW [RtmpCmdQTask] 6879 root 0 SW [RtmpWscTask] 6945 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6947 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6949 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6950 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6952 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6953 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6954 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6955 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6958 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 6959 root 1952 S /bin/wscd -m 1 -a 192.168.10.1 -i ra0 7004 root 2224 S crond 7031 root 0 SW [RtmpCmdQTask] 7032 root 0 SW [RtmpWscTask] 7033 root 0 SW [kworker/0:3] 7052 root 1452 S wps_daemon 7068 root 1332 S miniupnpd -f /var/tmp/upnpd_wan.conf -P /var/run/upnp 7112 root 2220 R ps ax


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Space for additional notes, links to forum threads or other resources.

Tags

FIXME Add tags below, then remove this fixme.

How to add tags

toh/trendnet/trendnet_tew-810dr_1.0_1.1.txt · Last modified: 2016/12/12 19:33 by supaplex