User Tools

Site Tools


toh:ubiquiti:unifiac

Ubiquiti UniFi AP AC

Ubiquiti has released a new series of UniFi APs supporting AC in Q4/2015.

  • UniFi AP AC LITE
  • UniFi AP AC PRO
  • UniFi AP AC MESH PRO
  • UniFi AP AC LR (Long Range)
  • UniFi AP AC EDU

From what is known of the official firmware releases, these devices seem to use the same platform.

:!: The devices released in Q4/2015 (and listed here) are generation 2 devices based on ar71xx platforms. The UniFiAP AC PRO from generation 1 (based on some Broadcom platform) is not covered by this article. To easily identify gen 1 and gen 2: gen 2 devices have circle-shaped cases, while especially the generation 1 AP AC PRO has a square-shaped body.

:!: For OpenWRT/LEDE on the MESH PRO, LAN and WAN port assignment is "unexpected." LAN is on the port labeled "Secondary", whereas the port labeled "Main" is WAN.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
UniFi AP AC LITEQualcomm Atheros QCA956377516128Qualcomm Atheros QCA988x 802.11a/n/ac - QCA9563 b/g/nb/g/na/n/ac-1No-
UniFi AP AC LRQualcomm Atheros QCA956377516128Qualcomm Atheros QCA988x 802.11a/n/ac - QCA9563 b/g/nb/g/na/n/ac-1No-
UniFi AP AC PROQualcomm Atheros QCA956377516128Qualcomm Atheros QCA988x 802.11a/n/ac - QCA9563 b/g/nb/g/na/n/ac-2No1x 2.0

Installation

If you can confirm that OpenWrt is running on this device (i.e. you or someone else has tested it), please update the data accordingly. → Click View/Edit data

Hardware

Version LITE LR PRO EDU
Instruction set: MIPS MIPS MIPS ?
Vendor: Qualcomm / Atheros Qualcomm / Atheros Qualcomm / Atheros ?
Bootloader: UBoot UBoot UBoot ?
System-On-Chip: QCA9563-AL3A ? QCA9563-AL3A ?
CPU Frq: 775 MHz 775 MHz 775 MHz ?
BogoMIPS: 385.84 385.84 385.84 ?
Flash-Chip: Macronix MX25L12835FMI ? Macronix MX25L12835FMI ?
Flash size: 16 MiB ? 16 MiB ?
RAM-Chip: Winbond W971GG6KB-25 ? Winbond W971GG6KB-25 ?
RAM size: 128 MiB 128 MiB 128 MiB ?
Wireless 1 (2.4 GHz): QCA9563 built-in ? QCA9563 built-in ?
Wireless 2 (5 GHz): Ubiquiti U-AME-G1-BR4A ? QCA9880-BR4A
Eth Phy: Atheros AR8033-AL1A ? QCA8334-AL3C ?
USB: possibly unpopulated ? USB 2.0 ?
Serial: Yes, for U-Boot Same as the AC Lite Same as the AC Lite ?
JTAG: N/A ? ? ?

5 GHz Wireless Phy

The chip Ubiquiti U-AME-G1-BR4A seems to be a custom labeled Atheros AR9888 (Note: The file "/etc/board.info" in Ubiquiti firmware calls it "Peregrine" and says the the VID:PID is 168c:003c, which seems to be AR8882). It is detected as QCA988X/hw2.0 and supported by the ath10k driver.

Depending on where you get the images you may have to install kmod-ath10k and ath10k-firmware-qca988x afterwards.

Firmware

OpenWrt Support

While LITE and LR are supported by current trunk, there is a patch (not applied yet) which brings support for PRO. Please be aware of the sysupgrade images which are compatible also with the original firmware. Do not find a similarly named factory image for your first installation.

Installing OpenWrt

:!: If you take images from current trunk, then you will have to afterwards install the packages kmod-ath10k and ath10k-firmware-qca988x in order to get the 5GHz phy working. This should not be the case as soon as the devices is included in a stable release.

Non-invasive method using mtd

Open an SSH session to the original firmware (User: ubnt, Pswd: ubnt). If no DHCP server is running, the AP will have the IP 192.168.1.20

Grab the correct image (whether you have the AC Lite or AC Pro/LR versions) and copy it to /tmp using scp:

scp openwrt-ar71xx-generic-ubnt-unifiac-squashfs-sysupgrade.bin ubnt@192.168.1.20:/tmp/

UniFi AP AC Lite devices

In the SSH session run the following commands to replace the primary firmware partition by OpenWrt:

BZ.v3.7.40# mtd write /tmp/openwrt-ar71xx-generic-ubnt-unifiac-lite-squashfs-sysupgrade.bin kernel0
Unlocking kernel0 ...
Erasing kernel0 ...
Writing from /tmp/openwrt-ar71xx-generic-ubnt-unifiac-lite-squashfs-sysupgrade.bin to kernel0 ...  [e/w]

BZ.v3.7.40# mtd -r write /tmp/openwrt-ar71xx-generic-ubnt-unifiac-lite-squashfs-sysupgrade.bin kernel1
Unlocking kernel1 ...
Erasing kernel1 ...
Writing from /tmp/openwrt-ar71xx-generic-ubnt-unifiac-lite-squashfs-sysupgrade.bin to kernel1 ...  [e/w]

Writing only to kernel0 does not upgrade the system; writing only to kernel1 ends in a kernel panic on reboot. Therefore, both partitions must be written (!!!).

UniFi AP AC LR and UniFi AP AC Pro devices

Running the above mtd command does not work for the UniFi AP AC LR model. If after reboot, the device is loaded with a default kernel, try using kernel1 instead of kernel0.

# mtd -r -e kernel0 write /tmp/openwrt-ar71xx-generic-ubnt-unifiac-pro-squashfs-sysupgrade.bin kernel0
Unlocking kernel0 ...
Erasing kernel0 ...

Writing from openwrt-ar71xx-generic-ubnt-unifiac-pro-squashfs-sysupgrade.bin to kernel0 ...
Rebooting ...

Using U-Boot with serial console

Another way to install OpenWrt is using the serial console, U-Boot and a tftp-server. Enter U-Boot by hitting a key to interrupt autoboot. Then enter the following commands. This will wipe the primary firmware partition and install OpenWrt there.

tftpboot 0x80000000 openwrt-ar71xx-generic-ubnt-unifiac-squashfs-sysupgrade.bin
erase 0x9f070000 +0x790000
cp.b 0x80000000 0x9f070000 0x380004
bootm 0x9f070000
The OEM firmware, which is still on the secondary firmware partition can be later booted either automatically as failover, or manually in U-Boot:
bootm 0x9f800000

Other ways

Since the UniFi series by design have no webserver-GUI at all, there won't be way to upload the file to the device in a browser. The usual Ubiquiti upgrade procedure (using syswrapper.sh or fwupdate.real) will not work here, as the images seem to be RSA-signed and these utilities complain: "FW Image partition 2 header or signature truncated."

Pushing and holding down the reset button (either on the device itself or on the PoE injector) while powering up the device leads to following behaviour:

  • after about 5 seconds the blue LED will light up and U-Boot erases the cfg-partition (which is only used in the original firmware). If you released the button by now, that's all, what happens.
  • keeping the button pushed for additional 8 seconds, it will also replace the U-Boot environment with a default one (which slightly differs from the shipped environment). However, this does not make much difference at all. As a result the unit starts a TFTP server on its default IP 192.168.1.20 and waits for a new firmware to be installed. The LEDs flash in a sequence (blue, white, pause, …). A binary which can be PUT (tftp client) to the device from 192.168.1.254 has to have a firmware header (a sysupgrade.bin will fail immediately). Currently it is not known which format (checksums or even signatures) the file should have. After loading a file with an appropriate header U-Boot tries to execute it (which in my case immediately returned and booted from the primary firmware partition).

This means that at the moment the only way of installing OpenWrt to the device without access to the serial console is by using the mtd method as described above.

OEM Firmware

You can download the official firmware archives for example at https://www.ubnt.com/download/unifi/unifi-ap-ac-lite, since the same firmare is used for UAP-AC-Lite/AC-LR/AC-Pro/AC-EDU devices.

Going back to the original firmware is no problem at all.

Flashing via TFTP

  1. Keep the reset button pressed while powering on the AP
  2. Wait until the LED ring is blinking blue/white (ca. 15 sec.)
  3. Follow the TFTP client instructions in here to transfer the image
  4. Wait until the device reboots (can take a few minutes) and the LED shines white again

:!: Be aware that this procedure overwrites both primary and secondary image!

Installing from OpenWRT

If you don't have a copy of the original mtd2 content, don't want to extract the partition out of the firmware images or don't want to deal with TFTP, you can copy the content of mtd6 (ubnt-airos) to mtd2 (firmware) and you're done.

Specific Configuration

All UniFi AP AC devices: LEDs

The UniFi AP AC has two LEDs, the blue one can be configured by adding something like:

config 'led'
	option 'name' 'lan'
	option 'sysfs' 'ubnt:blue:dome'
	option 'trigger' 'netdev'
	option 'dev' 'br-lan'
	option 'mode' 'tx rx' 
at the end of /etc/config/system.

UniFi AP AC PRO: Switch

The UniFi AP AC PRO has a built-in switch and two external Ethernet ports. Port 2 on the switch corresponds to the primary Ethernet connector, Port 3 to the secondary. In their default configuration primary/secondary are assigned LAN/WAN interface.

Photos

The thinner front part can be separated with one's fingernails. At five equally distributed locations at the outer ring it snaps from the outside into the main back part. No twisting/turning. Sharp tools are likely to damage the plastic. The platine is held with three easily reachable screws.

Unifi AP AC Lite
Unifi AP AC Lite PCB frontside Unifi AP AC Lite PCB backside

unifi-apac-lite-qca9563.jpg unifi-apac-lite-wifi.jpg

Unifi AP AC Pro
unifi-apac-pro_pcb_front.jpg unifi-apac-pro_pcb_back.jpg

Serial console

The device has two pinheaders with serial ports. Both ports operate at 3.3V level, 115200 Baud, 8N1 and have the pinout +3,3V - RX - TX - GND.

The port to the left (shown red) gives access to U-Boot and OpenWrt's console. The purpose of the other port (shown blue) is not identified yet.

Using the default/factory U-Boot environment there are no outputs from the kernel during booting. Instead, one has to send a newline at 9600 Baud (to activate the console) and then login at 115200 Baud again. To overcome this, one can alter the bootargs environment variable in U-Boot:

setenv bootargs 'console=ttyS0,115200 panic=3'
saveenv
Having it set that way, one can follow the kernel booting and can then directly login without switching Baudrates.

unifi-apac-lite_serial.jpg

Serial port outputs on OEM firmware

Serial Port 1 (left) on LITE

The output shown has a patched bootargs variable. Otherwise it would stop at Starting kernel…

U-Boot unifi-v1.6.2.235-g1aad87ce (Jun 30 2015 - 21:30:38) DRAM: sri ath_ddr_initial_config(278): (ddr2 init) ath_sys_frequency: cpu 775 ddr 650 ahb 258 Tap values = (0xf, 0xf, 0xf, 0xf) 128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 231k for U-Boot at: 87fc4000 Reserving 192k for malloc() at: 87f94000 Reserving 44 Bytes for Board Info at: 87f93fd4 Reserving 36 Bytes for Global Data at: 87f93fb0 Reserving 128k for boot params() at: 87f73fb0 Stack Pointer at: 87f73f98 Now running in RAM - U-Boot at: 87fc4000 Flash: 16 MB In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... No valid address in Flash. Using fixed address ath_gmac_enet_initialize: reset mask:c02200 athr_mgmt_init ::done Dragonfly ----> S17 PHY * ath_gmac_enet_initialize: is_s17()=0, is_ar8033()=1, phy id1=4d phy_id2=d074 WAN AR8033 PHY init athrs_ar8033_reg_init: Done 111 Max resets limit reached exiting... athr_gmac_sgmii_setup SGMII done : cfg1 0x80000000 cfg2 0x7114 eth0: 00:03:7f:__:__:__ eth0 up eth0 Setting 0x181162c0 to 0x1c382100 Board: Copyright Ubiquiti Networks Inc. 2014 Hit any key to stop autoboot: 2 1 0 ## Starting application at 0x80200020 ... Board: Ubiquiti Networks AR956X board (e517-18.1150.0030.0040) 0. Name = u-boot, offset = 0, start_addr=9f000000, size=393216,start_sector=0, end_sector=5 1. Name = u-boot-env, offset = 60000, start_addr=9f060000, size=65536,start_sector=6, end_sector=6 2. Name = kernel0, offset = 70000, start_addr=9f070000, size=7929856,start_sector=7, end_sector=127 3. Name = kernel1, offset = 800000, start_addr=9f800000, size=7929856,start_sector=128, end_sector=248 4. Name = bs, offset = f90000, start_addr=9ff90000, size=131072,start_sector=249, end_sector=250 5. Name = cfg, offset = fb0000, start_addr=9ffb0000, size=262144,start_sector=251, end_sector=254 6. Name = EEPROM, offset = ff0000, start_addr=9fff0000, size=65536,start_sector=255, end_sector=255 get_mtd_params: name=bs ubnt_flash_read: addr=8023b480, sa=9ff90000, sz=131072 ubnt_bootsel_init: bootsel magic=a34de82b, bootsel = 0 UBNT application initialized ## Application terminated, rc = 0x0 ## Starting application at 0x80200020 ... keep cfg partition. ## Application terminated, rc = 0x0 ## Starting application at 0x80200020 ... ubnt_uwrite: Nothing to flash, exiting ## Application terminated, rc = 0x0 ## Starting application at 0x80200020 ... Number of boot partitions = 2 get_mtd_params: name=bs ubnt_flash_read: addr=8023b480, sa=9ff90000, sz=131072 ubnt_get_bootsel: Boot partition selected = 0 Loading Kernel Image @ 81000000, size = 7929856 Verifying 'kernel0' parition:OK ## Application terminated, rc = 0x0 ## Booting image at 9f070000 ... Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2015-09-12 0:03:12 UTC Image Type: MIPS Linux Multi-File Image (lzma compressed) Data Size: 6877256 Bytes = 6.6 MB Load Address: 80060000 Entry Point: 80060000 Contents: Image 0: 6877248 Bytes = 6.6 MB Verifying Checksum at 0x9f070040 ...OK Uncompressing Multi-File Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 134217728 Starting kernel ... [ 0.000000] Linux version 3.3.8 (build-unifi@ubnt-builder3) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Fri Sep 11 17:02:52 PDT 2015 [ 0.000000] CPU revision is: 00019750 (MIPS 74Kc) [ 0.000000] SoC: Qualcomm Atheros QCA956X rev 0 [ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00008000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00008000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 panic=3 ubntbootid=0 mtdparts=ath-nor0:384k(u-boot),64k(u-boot-env),7744k(kernel0),7744k(kernel1),128k(bs),256k(cfg),64k(EEPROM) mem=128M ubootver=unifi-v1.6.2.235-g1aad87ce board=UBNTGen2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 104484k/131072k available (2372k kernel code, 26588k reserved, 578k data, 21808k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:83 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.050000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.060000] Initialized recycle list for cpu 0. [ 0.060000] NET: Registered protocol family 16 [ 0.060000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79 [ 0.060000] MIPS: machine is Ubiquiti Networks Inc. (c) 2015 [ 0.060000] ubnt_gen2_setup: Board ID = e517 [ 0.100000] registering PCI controller with io_map_base unset [ 0.310000] bio: create slab <bio-0> at 0 [ 0.310000] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.310000] PCI host bridge to bus 0000:00 [ 0.310000] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff] [ 0.310000] pci_bus 0000:00: root bus resource [io 0x0001] [ 0.310000] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 0.310000] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref] [ 0.310000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.310000] Switching to clocksource MIPS [ 0.320000] NET: Registered protocol family 2 [ 0.320000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.320000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.320000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.320000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.320000] TCP reno registered [ 0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.320000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.320000] NET: Registered protocol family 1 [ 0.520000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.520000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.520000] msgmni has been set to 204 [ 0.520000] io scheduler noop registered [ 0.520000] io scheduler deadline registered (default) [ 0.520000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.550000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.920000] console [ttyS0] enabled [ 0.920000] 7 cmdlinepart partitions found on MTD device ath-nor0 [ 0.930000] Creating 7 MTD partitions on "ath-nor0": [ 0.930000] 0x000000000000-0x000000060000 : "u-boot" [ 0.940000] 0x000000060000-0x000000070000 : "u-boot-env" [ 0.950000] 0x000000070000-0x000000800000 : "kernel0" [ 0.950000] 0x000000800000-0x000000f90000 : "kernel1" [ 0.960000] 0x000000f90000-0x000000fb0000 : "bs" [ 0.970000] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.970000] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.980000] ath_flash_init: init ath_flash driver, res=0 [ 0.990000] ag71xx_mdio: probed [ 0.990000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.550000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd074, driver=Qualcomm Atheros AR8033 PHY] [ 1.560000] ALSA device list: [ 1.560000] No soundcards found. [ 1.570000] u32 classifier [ 1.570000] Performance counters on [ 1.570000] input device check on [ 1.580000] Actions configured [ 1.580000] TCP cubic registered [ 1.590000] NET: Registered protocol family 17 [ 1.590000] Bridge firewalling registered [ 1.590000] 8021q: 802.1Q VLAN Support v1.8 [ 1.600000] ### of_selftest(): No testcase data in device tree; not running tests [ 1.730000] Freeing unused kernel memory: 21808k freed [ 1.760000] ubnthal: module license 'Proprietary' taints kernel. [ 1.770000] Disabling lock debugging due to kernel taint [ 1.780000] Init caladdr[0]=0xbfff1000 caladdr[1]=0xbfff5000 [ 1.780000] [ 1.790000] Init caladdr[0]=0xbfff1000 caladdr[1]=0xbfff5000 [ 1.790000] [ 1.800000] ubnthal: Ubiquiti UAP-AC-Lite [ 1.800000] ubnthal: Dragonfly: maxPower 20 powerOffset 0 txmask 3 antenna 4 [0] gain 0 caps 0x4014 [ 1.810000] ubnthal: Peregrine: maxPower 20 powerOffset 0 txmask 3 antenna 4 [0] gain 0 caps 0x4014 [ 1.820000] gpiodev: (reset_timeout=3 factory_countdown=1000000) ...running /sbin/init init started: BusyBox v1.19.4 (2015-09-11 16:51:29 PDT) [ 3.130000] NET: Registered protocol family 10 [ 3.190000] usbcore: registered new interface driver usbfs [ 3.190000] usbcore: registered new interface driver hub [ 3.200000] usbcore: registered new device driver usb [ 3.270000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.280000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller [ 3.280000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 3.320000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 3.340000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 3.340000] hub 1-0:1.0: USB hub found [ 3.350000] hub 1-0:1.0: 1 port detected [ 3.350000] ehci-platform ehci-platform.1: Generic Platform EHCI Controller [ 3.360000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 3.400000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 3.420000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00 [ 3.420000] hub 2-0:1.0: USB hub found [ 3.430000] hub 2-0:1.0: 1 port detected [ 3.470000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.510000] usbcore: registered new interface driver snd-usb-audio UBNT load board.bin file + exec [ 5.280000] ****Address of trace_timer :85dd2620 [ 5.560000] ath_hal: 0.9.17.1 (AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [ 5.820000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 5.840000] ath_dfs: Version 2.0.0 [ 5.840000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 5.860000] ath_spectral: Version 2.0.0 [ 5.860000] Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 5.870000] SPECTRAL module built on Sep 11 2015 16:58:22 [ 6.140000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 6.500000] __ath_attach: Set global_scn[0] [ 6.510000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead *** [ 6.520000] ACBKMinfree = 48 [ 6.520000] ACBEMinfree = 32 [ 6.520000] ACVIMinfree = 16 [ 6.530000] ACVOMinfree = 0 [ 6.530000] CABMinfree = 48 [ 6.530000] UAPSDMinfree = 0 [ 6.540000] ATH_TXBUF=4096 [ 6.540000] register caladdr[0]=0x8032e1d4 caladdr[1]=0xbfff5000 [ 6.540000] [ 6.550000] Bootstrap clock 25MHz [ 6.560000] Enterprise mode: 0x03bda000 [ 6.560000] Restoring Cal data from DRAM [ 6.570000] [ 6.570000] ART Version : -48.0.0 [ 6.570000] SW Image Version : -48.0.0.0.0 [ 6.580000] Board Revision : [ 6.580000] ath_hal: Ubiquiti Dragonfly [ 6.580000] ath_hal: maxPower 40 minPower 0 powerOffset 0 [ 6.590000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125 [ 6.600000] SPECTRAL : get_capability not registered [ 6.600000] HAL_CAP_PHYDIAG : Capable [ 6.610000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 6.610000] SPECTRAL : get_capability not registered [ 6.620000] HAL_CAP_RADAR : Capable [ 6.620000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 6.620000] (spectral_attach : 236) [ 6.630000] SPECTRAL : get_capability not registered [ 6.640000] HAL_CAP_SPECTRAL_SCAN : Capable [ 6.640000] SPECTRAL : get_tsf64 not registered [ 6.650000] spectral_init_netlink 65 NULL SKB [ 6.650000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT [ 6.660000] SPECTRAL :----- module attached [ 6.660000] Green-AP : Green-AP : Attached [ 6.660000] [ 6.670000] ath_get_caps[6202] rx chainmask mismatch actual 3 sc_chainmak 0 [ 6.680000] ath_get_caps[6177] tx chainmask mismatch actual 3 sc_chainmak 0 [ 6.690000] ath_attach_dfs[12869] dfsdomain 0 [ 6.700000] SPECTRAL : module already attached [ 6.720000] ath_tx_paprd_init sc 85e80000 PAPRD disabled in HAL [ 6.730000] wifi0: Atheros 956X: mem=0xb8100000, irq=47 [ 6.730000] ath_pci: 10.2.r2-00013-4 (Atheros/multi-bss) [ 6.740000] wevent: registered [ 6.750000] qos: registered [ 6.750000] ath_pci_probe [ 6.750000] PCI device id is 003c :003c [ 6.760000] ath_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 6.770000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 6.770000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x81655000 [ 6.780000] [ 6.780000] ol_ath_pci_configure : num_desired MSI set to 0 [ 6.790000] [ 6.790000] Using PCI Legacy Interrupt [ 7.790000] CE_per_engine_handler_adjust, base=81655000 offset=00057400 [ 7.790000] CE_per_engine_handler_adjust, base=81655000 offset=00057800 [ 7.810000] __ol_ath_attach: ath_attach TODO [ 7.820000] __ol_ath_attach: dev name wifi1 [ 7.820000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 7.830000] OL_ACBKMinfree : 0 [ 7.830000] OL_ACBEMinfree : 0 [ 7.840000] OL_ACVIMinfree : 0 [ 7.840000] OL_ACVOMinfree : 0 [ 7.840000] ol_ath_attach() BMI inited. [ 7.850000] ol_ath_attach() BMI Get Target Info. [ 7.850000] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 7.860000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 7.860000] ol_ath_attach() configure Target . [ 7.870000] register caladdr[0]=0x8032e1d4 caladdr[1]=0xc06f8000 [ 7.870000] [ 7.880000] qc98xx_verify_checksum: flash checksum passed: 0xa4f3 [ 7.880000] ol_transfer_bin_file 2319: Download Flash data len 2116 [ 7.900000] ol_ath_hal: Ubiquiti Peregrine [ 7.900000] ol_ath_hal: maxPower 40 minPower 0 powerOffset 0 [ 7.910000] ol_transfer_bin_file 2374: Download UBNT card data len 36 [ 7.910000] Download AR9888v2_bin [ 7.920000] ol_transfer_bin_file 2231: Download Firmware data len 239024 [ 8.940000] ol_ath_attach() Download FW. [ 8.940000] ol_ath_attach() HT Create . [ 8.940000] ol_ath_attach() HIF Claim. [ 8.950000] ol_ath_attach() BMI Done. [ 8.950000] ol_ath_attach() WMI attached. wmi_handle 80c50000 [ 8.960000] +HWT [ 8.960000] SOC_RESET_CONTROL_ADDRESS : 800 [ 8.960000] CPU_INTR_ADDRESS = [0] [ 8.970000] SOC_GLOBAL_RESET_ADDRESS = [0] [ 8.970000] Rx_Filter : [0] [ 8.980000] CE_per_engine_handler_adjust, base=81655000 offset=00057400 [ 8.980000] CE_per_engine_handler_adjust, base=81655000 offset=00057800 [ 8.990000] CE_per_engine_handler_adjust, base=81655000 offset=00057c00 [ 9.000000] CE_per_engine_handler_adjust, base=81655000 offset=00058000 [ 9.000000] CE_per_engine_handler_adjust, base=81655000 offset=00058400 [ 9.010000] CE_per_engine_handler_adjust, base=81655000 offset=00058800 [ 9.020000] CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5 [ 9.030000] CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x925020 nbytes 0 recv_ctxt 0x85ca4840 [ 9.040000] Target:85de4000 HTC Service:0x0001, ULpipe:0 DLpipe:1 id:0 Ready [ 9.040000] -HWT [ 9.050000] Target:85de4000 HTC Service:0x0300, ULpipe:4 DLpipe:5 id:1 Ready [ 9.050000] HTC Service:0x0300 ep:1 TX flow control disabled [ 9.060000] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 9.070000] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from 80580000 [ 9.080000] Target:85de4000 HTC Service:0x0100, ULpipe:3 DLpipe:2 id:2 Ready [ 9.080000] HTC Service:0x0100 ep:2 TX flow control disabled [ 9.090000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 9.100000] num_rf_chain : 00000002 [ 9.100000] ht_cap_info: : 0000085b [ 9.100000] vht_cap_info : 338001b2 [ 9.110000] vht_supp_mcs : 0000fffa [ 9.110000] LARGE_AP enabled. num_peers 136, num_vdevs 8, num_tids 256, lteu_support 0 [ 9.120000] idx 0 req 1 num_units 0 num_unit_info 2 unit size 440 actual units 137 [ 9.130000] chunk 0 len 60280 requested ,ptr 0x590000 [ 9.140000] FIRMWARE:P 137 V 8 T 419 [ 9.140000] [ 9.150000] FIRMWARE:_wlan_rtt_enable [ 9.150000] wmi_ready_event_rx: WMI UNIFIED READY event [ 9.160000] ol_ath_connect_htc() WMI is ready [ 9.160000] ol_ath_set_host_app_area TODO [ 9.170000] target uses HTT version 2.1; host uses 2.1 [ 9.180000] ol_ath_attach() connect HTC. [ 9.180000] bypasswmi : 0 [ 9.190000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 9.200000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 [ 9.210000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 [ 9.210000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 [ 9.220000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 [ 9.230000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 [ 9.230000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 [ 9.240000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 [ 9.250000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 [ 9.260000] Add VHT80 channel: 5210 [ 9.260000] Add VHT80 channel: 5290 [ 9.260000] Add VHT80 channel: 5530 [ 9.270000] Add VHT80 channel: 5775 [ 9.270000] Skipping VHT80 channel 5580 [ 9.280000] Skipping VHT80 channel 5660 [ 9.280000] Skipping VHT80 channel 5680 [ 9.280000] Skipping VHT80 channel 5700 [ 9.290000] Skipping VHT80 channel 5825 [ 9.290000] ol_ath_phyerr_attach: called [ 9.300000] OL Resmgr Init-ed [ 9.300000] ol_if_spectral_setup [ 9.300000] SPECTRAL : get_capability not registered [ 9.310000] HAL_CAP_PHYDIAG : Capable [ 9.310000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 9.320000] SPECTRAL : get_capability not registered [ 9.320000] HAL_CAP_RADAR : Capable [ 9.330000] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 9.330000] (spectral_attach : 236) [ 9.340000] SPECTRAL : get_capability not registered [ 9.340000] HAL_CAP_SPECTRAL_SCAN : Capable [ 9.350000] SPECTRAL : get_tsf64 not registered [ 9.350000] spectral_init_netlink 65 NULL SKB [ 9.360000] Green-AP : Green-AP : Attached [ 9.360000] [ 9.360000] Green-AP : Attached [ 9.370000] ol_if_dfs_setup: called [ 9.370000] ol_if_dfs_attach: called; ptr=805c1974, radar_info=85d7fb70 [ 9.380000] ol_ath_rtt_meas_report_attach: called [ 9.380000] ol_ath_attach() UMAC attach . [ 9.390000] ol_if_dfs_configure: called [ 9.390000] ol_if_dfs_configure: FCC domain [ 9.400000] ol_if_dfs_disable: called [ 9.400000] ol_ath_attach: Calling ol_if_dfs_configure [ 9.410000] __ol_ath_attach: init tx/rx TODO [ 9.410000] __ol_ath_attach: hard_header_len reservation 58 [ 9.420000] Initializing Pktlogs for 11ac [ 9.950000] [wifi1] FWLOG: [27541] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 ) [ 9.960000] [wifi1] FWLOG: [27541] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 ) [ 9.970000] [wifi1] FWLOG: [27541] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 ) [ 9.980000] [wifi1] FWLOG: [27541] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 ) [ 9.990000] [wifi1] FWLOG: [27546] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 ) [ 10.000000] [wifi1] FWLOG: [27546] WHAL_ERROR_RESET_PM ( ) [ 10.000000] [wifi1] FWLOG: [27554] WAL_DBGID_DEV_RESET ( 0x1, 0x1, 0x1 ) [ 10.010000] [wifi1] FWLOG: [27811] ANI Enable: 1 [ 10.020000] [wifi1] FWLOG: [27819] WAL_DBGID_DEV_RESET ( 0x1, 0x1, 0x1 ) [ 11.510000] ath_attach_dfs[12869] dfsdomain 0 [ 11.530000] wlan_vap_create : enter. devhandle=0x81640380, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 11.540000] wlan_vap_create : exit. devhandle=0x81640380, opmode=IEEE80211_M_HOSTAP, flags=0x1. [ 11.550000] VAP device ath0 created osifp: (85d81380) os_if: (85e90000) [ 11.590000] setting antenna gain to 0 [ 11.630000] Set freq vap 0 stop send + 85e90000 [ 11.630000] Set freq vap 0 stop send -85e90000 [ 11.770000] Set wait done --85e90000 [ 11.780000] WARNING: Fragmentation with HT mode NOT ALLOWED!! [ 11.840000] isCountryCodeValid: EEPROM regdomain 0x0 [ 11.850000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 [ 11.860000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 [ 11.860000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 [ 11.870000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 [ 11.880000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 [ 11.890000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 [ 11.890000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 [ 11.900000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 [ 11.910000] Add VHT80 channel: 5210 [ 11.910000] Add VHT80 channel: 5290 [ 11.920000] Add VHT80 channel: 5530 [ 11.920000] Add VHT80 channel: 5775 [ 11.920000] Skipping VHT80 channel 5580 [ 11.930000] Skipping VHT80 channel 5660 [ 11.930000] Skipping VHT80 channel 5680 [ 11.930000] Skipping VHT80 channel 5700 [ 11.940000] Skipping VHT80 channel 5825 [ 11.950000] ath_ioctl: SIOC80211IFCREATE CALLED [ 11.950000] wmi_unified_vdev_create_send: ID = 0 VAP Addr = 44:d9:e7:__:__:__: [ 11.960000] wmi_unified_set_psmode:set psmode=1 [ 11.960000] Setting dscp for vap id: 0 [ 11.970000] VAP device ath1 created osifp: (80674380) os_if: (80660000) [ 12.060000] WARNING: Fragmentation with HT mode NOT ALLOWED!! [ 12.260000] ol_ath_desc_alloc_and_mark_for_mcast_clone: VAP Mcast to Unicast buffer allocated: 400 [ 12.270000] ol_ath_vap_set_param: VAP param is now supported param:68 value:2 [ 12.320000] wmi_unified_set_psmode:set psmode=0 [ 12.320000] wmi_unified_set_psmode:set psmode=0 [ 12.360000] Ebtables v2.0 registered [ 12.600000] device eth0 entered promiscuous mode [ 12.610000] device ath0 entered promiscuous mode [ 12.620000] device ath1 entered promiscuous mode [ 12.640000] ADDRCONF(NETDEV_UP): br0: link is not ready [ 12.650000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.740000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 Please press Enter to activate this console. [ 12.800000] DEVICE IS DOWN ifname=ath0 [ 12.800000] DEVICE IS DOWN ifname=ath0 [ 12.960000] [wifi1] FWLOG: [30482] WAL_DBGID_DEV_RESET ( 0x1, 0x1, 0x1 ) [ 13.320000] br0: port 2(ath0) entered forwarding state [ 13.320000] br0: port 2(ath0) entered forwarding state [ 13.330000] 8021q: adding VLAN 0 to HW filter on device ath0 [ 13.340000] ADDRCONF(NETDEV_CHANGE): br0: link becomes ready [ 13.480000] br0: port 3(ath1) entered forwarding state [ 13.480000] br0: port 3(ath1) entered forwarding state [ 13.490000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 13.490000] 8021q: adding VLAN 0 to HW filter on device ath1 [ 13.600000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 13.710000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 13.820000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 13.930000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.040000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.150000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.260000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.320000] br0: port 2(ath0) entered forwarding state [ 14.370000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.480000] br0: port 3(ath1) entered forwarding state [ 14.480000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.580000] br0: port 3(ath1) entered disabled state [ 14.600000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.710000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.820000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 14.930000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.040000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.150000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.260000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.370000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.480000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.590000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.700000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.810000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 15.920000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.030000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.140000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.250000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.360000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.470000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.580000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.600000] eth0: link up (1000Mbps/Full duplex) [ 16.600000] br0: port 1(eth0) entered forwarding state [ 16.610000] br0: port 1(eth0) entered forwarding state [ 16.610000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.690000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.800000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 16.910000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.020000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.130000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.240000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.350000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.460000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.570000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.610000] br0: port 1(eth0) entered forwarding state [ 17.680000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.790000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.900000] wmi_unified_scan_start_send for vap 0 (80c50000) [ 17.970000] Scan in progress.. Cancelling it [ 17.970000] ol_scan_cancel for (80c50000) [ 21.580000] br0: port 3(ath1) entered disabled state [ 23.740000] br0: no IPv6 routers present [ 24.070000] ath0: no IPv6 routers present [ 26.870000] eth0: no IPv6 routers present UBNT login: ubnt Password: BusyBox v1.19.4 (2015-09-11 16:51:29 PDT) built-in shell (ash) Enter 'help' for a list of built-in commands. BZ.v3.4.7#


Serial Port 1, U-Boot commands/environment

The environment variables here reflect the default/factory configuration. (bootargs is not changed yet)

Hit any key to stop autoboot:  0 
ath> help

?       - alias for 'help'
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
chpart	- change active partition
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
dhcp	- invoke DHCP client to obtain IP/boot params
erase   - erase FLASH memory
exit    - exit script
flinfo  - print FLASH memory information
fsinfo	- print information about filesystems
fsload	- load binary file from a filesystem image
go      - start application at address 'addr'
help    - print online help
loop    - infinite loop on address range
ls	- list files in a directory (default /)
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing)
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mw      - memory write (fill)
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
ping	- send ICMP ECHO_REQUEST to network host
pll cpu-pll dither ddr-pll dither - Set to change CPU & DDR speed
pll erase
pll get
printenv- print environment variables
progmac - Set ethernet MAC addresses
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
ubntfsboot  - UBNT fsboot command
urescue	- start TFTP server and wait for firmware
version - print monitor version
ath> printenv

bootargs=console=tty0 panic=3
bootcmd=run ubntappinit; go $ubntaddr ubntboot;bootm $flash_boot_addr
bootdelay=2
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.1.20
serverip=192.168.1.254
ubntappinit=go ${ubntaddr} uappinit;go ${ubntaddr} ureset_button;urescue;go ${ubntaddr} uwrite
mtdparts=mtdparts=ath-nor0:384k(u-boot),64k(u-boot-env),7744k(kernel0),7744k(kernel1),128k(bs),256k(cfg),64k(EEPROM)
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
ubntaddr=80200020

Serial Port 2 (right)

The following lines immediately show up after supplying power to the board.

CLI>build_version=0x11, rom_version=0x41020000, ram_version=0x11, stack_size=6348
reset reason=0x0

Image startup of Normal mode

Serial port output with OpenWrt on LITE

[U-Boot, as in OEM firmware] Loading Kernel Image @ 81000000, size = 7929856 Verifying 'kernel0' parition:OK ## Application terminated, rc = 0x0 ## Booting image at 9f070000 ... Image Name: MIPS OpenWrt Linux-4.1.13 Created: 2015-12-21 22:27:04 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1257815 Bytes = 1.2 MB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum at 0x9f070040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 134217728 Starting kernel ... [ 0.000000] Linux version 4.1.13 (______@______) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r47954) ) #10 Mon Dec 21 23:26:13 CET 2015 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc) [ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=UBNT-UF-AC mtdparts=spi0.0:384k(u-boot)ro,64k(u-boot-env)ro,7744k(firmware),7744k(ubnt-airos)ro,128k(bs)ro,256k(cfg)ro,64k(EEPROM)ro console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 125532K/131072K available (2799K kernel code, 140K rwdata, 572K rodata, 252K init, 195K bss, 5540K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:83 [ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz [ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns [ 0.000006] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns [ 0.007430] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.069910] pid_max: default: 32768 minimum: 301 [ 0.074416] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080682] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.089614] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.099435] NET: Registered protocol family 16 [ 0.104709] MIPS: machine is Ubiquiti UniFi-AC [ 0.333545] registering PCI controller with io_map_base unset [ 0.346460] PCI host bridge to bus 0000:00 [ 0.350355] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff] [ 0.356883] pci_bus 0000:00: root bus resource [io 0x0001] [ 0.362216] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.368699] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.376326] pci 0000:00:00.0: invalid calibration data [ 0.381523] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 0.388489] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref] [ 0.395361] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.400718] Switched to clocksource MIPS [ 0.405429] NET: Registered protocol family 2 [ 0.410258] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.416892] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.422956] TCP: Hash tables configured (established 1024 bind 1024) [ 0.429083] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.434636] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.440861] NET: Registered protocol family 1 [ 0.445829] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.465164] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.470688] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.482326] io scheduler noop registered [ 0.486013] io scheduler deadline registered (default) [ 0.491137] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.520916] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A [ 0.529105] console [ttyS0] enabled [ 0.529105] console [ttyS0] enabled [ 0.536272] bootconsole [early0] disabled [ 0.536272] bootconsole [early0] disabled [ 0.546681] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.551980] 7 cmdlinepart partitions found on MTD device spi0.0 [ 0.558088] Creating 7 MTD partitions on "spi0.0": [ 0.563058] 0x000000000000-0x000000060000 : "u-boot" [ 0.568883] 0x000000060000-0x000000070000 : "u-boot-env" [ 0.575040] 0x000000070000-0x000000800000 : "firmware" [ 0.595672] 2 uimage-fw partitions found on MTD device firmware [ 0.601819] 0x000000070000-0x0000001b0000 : "kernel" [ 0.607564] 0x0000001b0000-0x000000800000 : "rootfs" [ 0.613337] mtd: device 4 (rootfs) set to be root filesystem [ 0.619226] 1 squashfs-split partitions found on MTD device rootfs [ 0.625645] 0x0000003c0000-0x000000800000 : "rootfs_data" [ 0.631880] 0x000000800000-0x000000f90000 : "ubnt-airos" [ 0.637992] 0x000000f90000-0x000000fb0000 : "bs" [ 0.643424] 0x000000fb0000-0x000000ff0000 : "cfg" [ 0.648898] 0x000000ff0000-0x000001000000 : "EEPROM" [ 0.664040] libphy: ag71xx_mdio: probed [ 1.331534] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd074, driver=Atheros 8031/8033 ethernet] [ 1.342870] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII [ 1.350822] NET: Registered protocol family 10 [ 1.358102] NET: Registered protocol family 17 [ 1.362811] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.375962] 8021q: 802.1Q VLAN Support v1.8 [ 1.386828] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.395519] Freeing unused kernel memory: 252K (803d1000 - 80410000) [ 2.238185] init: Console is alive [ 2.241936] init: - watchdog - [ 3.160919] usbcore: registered new interface driver usbfs [ 3.166655] usbcore: registered new interface driver hub [ 3.172239] usbcore: registered new device driver usb [ 3.181850] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.189727] ehci-platform: EHCI generic platform driver [ 3.197505] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.204931] ohci-platform: OHCI generic platform driver [ 3.245706] init: - preinit - [ 3.848749] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3.871621] random: procd urandom read with 6 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 5.402443] eth0: link up (1000Mbps/Full duplex) [ 5.407060] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.074771] jffs2: notice: (342) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 7.092542] mount_root: switching to jffs2 overlay [ 7.121684] eth0: link down [ 7.133828] procd: - early - [ 7.136887] procd: - watchdog - [ 7.797637] procd: - ubus - [ 8.858792] procd: - init - Please press Enter to activate this console. [ 9.363733] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.379385] Loading modules backported from Linux version master-2015-12-03-0-g1677f62 [ 9.387602] Backport generated by backports.git backports-20151120-0-g906a6b3 [ 9.410832] cfg80211: World regulatory domain updated: [ 9.416154] cfg80211: DFS Master region: unset [ 9.420649] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 9.430743] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 9.439002] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 9.447270] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 9.455541] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 9.465334] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 9.475127] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 9.483486] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 9.491755] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 9.566470] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 9.572899] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0 [ 9.914407] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 0000:0000 [ 9.923974] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 9.936952] ath10k_pci 0000:00:00.0: firmware ver 10.2.4.70.12-2 api 5 features no-p2p,raw-mode crc32 cc3fb466 [ 9.987472] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2 [ 9.998271] ath10k_pci 0000:00:00.0: Falling back to user helper [ 10.072738] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed [ 10.082186] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 11.128959] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 11.250990] cfg80211: Regulatory domain changed to country: US [ 11.257020] cfg80211: DFS Master region: FCC [ 11.261363] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.271432] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 11.279692] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A) [ 11.289486] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s) [ 11.299276] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s) [ 11.307633] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 11.315905] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 11.387131] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.408716] nf_conntrack version 0.5.0 (1965 buckets, 7860 max) [ 11.462600] xt_time: kernel timezone is -0000 [ 11.504975] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=47 [ 16.940016] device eth0 entered promiscuous mode [ 16.957560] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 18.462444] eth0: link up (1000Mbps/Full duplex) [ 18.467073] br-lan: port 1(eth0) entered forwarding state [ 18.472696] br-lan: port 1(eth0) entered forwarding state [ 18.479449] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 20.470726] br-lan: port 1(eth0) entered forwarding state BusyBox v1.24.1 (2015-12-20 22:47:10 CET) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- DESIGNATED DRIVER (Bleeding Edge, r47954) ----------------------------------------------------- * 2 oz. Orange Juice Combine all juices in a * 2 oz. Pineapple Juice tall glass filled with * 2 oz. Grapefruit Juice ice, stir well. * 2 oz. Cranberry Juice ----------------------------------------------------- root@OpenWrt:/#


Tags

toh/ubiquiti/unifiac.txt · Last modified: 2017/11/04 22:38 by RAThomas