Differences

This shows you the differences between two versions of the page.

toh:widemac:sl-r7205 [2013/04/13 10:07]
toh:widemac:sl-r7205 [2014/08/14 15:32] (current)
rspliet Add configuration for VLAN
Line 44: Line 44:
==== OEM installation using the TFTP method ==== ==== OEM installation using the TFTP method ====
-OpenWrt was installed with the serial port and tftp method. There is currently no known way to flash directly from the built-in firmware.  So, follow [[doc:howto:generic.flashing.tftp]] for general setup of a tftp server and firmware to load. Set your terminal to 57600 bauds, 8,N, 1. At boot, you will see the following on your serial terminal:+OpenWrt was installed with the serial port and tftp method. There is currently no known way to flash directly from the built-in firmware.  So, follow [[doc:howto:generic.flashing.tftp]] for general setup of a tftp server and firmware to load. Use the sysupgrade image. Set your terminal to 57600 bauds, 8,N, 1. At boot, you will see the following on your serial terminal:
'' ''
Line 55: Line 55:
'' ''
-choose 2, then answer the prompts.+choose 2, then answer the prompts. Note that option 1 does not work with the sysupgrade image; booting will fail on finding the root partition. 
 + 
 +After installation, copy-paste the following configuration into /etc/config/network 
 +  config interface 'loopback' 
 +        option ifname 'lo' 
 +        option proto 'static' 
 +        option ipaddr '127.0.0.1' 
 +        option netmask '255.0.0.0' 
 +   
 +  config globals 'globals' 
 +        option ula_prefix 'fd37:bd9a:2b09::/48' 
 +   
 +  config switch 'switch0' 
 +        option enable '1' 
 +        option enable_vlan '1' 
 +        option reset '1' 
 +   
 +  config switch_vlan 
 +        option vlan '1' 
 +        option device 'switch0' 
 +        option ports '0 6t' 
 +   
 +  config switch_vlan 
 +        option vlan '2' 
 +        option device 'switch0' 
 +        option ports '1 2 3 4 6t' 
 +   
 +  config switch_port                                         
 +        option port '0' 
 +        option pvid '1' 
 +   
 +  config interface 'lan' 
 +        option force_link '1' 
 +        option type 'bridge' 
 +        option proto 'static' 
 +        option ipaddr '192.168.1.1' 
 +        option netmask '255.255.255.0' 
 +        option ip6assign '60' 
 +        option _orig_ifname 'eth0.2 wlan0' 
 +        option _orig_bridge 'true' 
 +        option ifname 'eth0.2' 
 +        option nat '1' 
 +   
 +  config interface 'wan' 
 +        option proto 'dhcp' 
 +        option _orig_ifname 'eth0.1' 
 +        option _orig_bridge 'false' 
 +        option ifname 'eth0.1' 
 +        option broadcast '1' 
 + 
 +Reboot, and the network ports should be operational. 
 + 
 +  WARNING: The current OpenWRT image does not contain a valid configuration for the various wired network ports 
 +  on the device. As a result, wired networking broken until copy-pasting in the above configuration.
  - -> [[doc:howto:obtain.firmware]]   - -> [[doc:howto:obtain.firmware]]
Line 138: Line 191:
| **[[doc:hardware:soc|System-On-Chip]]:**  | RT3052 | | **[[doc:hardware:soc|System-On-Chip]]:**  | RT3052 |
| **[[doc:hardware:cpu|CPU]]/Speed**        | 24Kc 384 Mhz | | **[[doc:hardware:cpu|CPU]]/Speed**        | 24Kc 384 Mhz |
-| **Flash-Chip:**      | [[http://www.alldatasheet.com/view.jsp?Searchword=29LV320DB|29LV320DBTI-70G]] +| **Flash-Chip:**      | [[http://www.alldatasheet.com/view.jsp?Searchword=29LV320DB|29LV320DBTI-70G]]/[[http://www.spansion.com/Support/Datasheets/S25FL064P_00_03_e.pdf|ST 25P64V6P]] |
-| **Flash-Chip:**      | s25sl064a [[http://www.spansion.com/Support/Datasheets/S25FL064P_00_03_e.pdf|ST 25P64V6P]] |+
| **Flash size:**      | 4096 KiB | | **Flash size:**      | 4096 KiB |
| **RAM:**            | 32 MiB  | | **RAM:**            | 32 MiB  |
Line 191: Line 243:
==== Serial port ==== ==== Serial port ====
-The [[doc:hardware:port.serial|serial port]] is on the unpopulated header labelled "console"/"J2". Pins are, from the pin closest to J2 Gnd, Rx, Tx, Vcc. Use a level shifter. Some of the boards are shipped with a populated header. Use 57600 8N1, hard & soft flow control OFF.+The [[doc:hardware:port.serial|serial port]] is on the unpopulated header labelled "console"/"J2". Pins are, from the pin closest to J2 Gnd, Rx, Tx, Vcc. Use a 5V <-> 3.3V level shifter. Some of the boards are shipped with a populated header. Use 57600 8N1, hard & soft flow control OFF.
**Photo of PCB with markings** **Photo of PCB with markings**
Line 219: Line 271:
-{{tag>FastEthernet 5Port USB 1USB DetachableAntenna 32RAM 4Flash MIPS}}+{{tag>ramips rt3052 FastEthernet 5Port USB 1USB DetachableAntenna 32RAM 4Flash MIPS}}

Back to top

toh/widemac/sl-r7205.1365840435.txt.bz2 · Last modified: 2013/04/13 10:07 (external edit)