User Tools

Site Tools


toh:wistron:ca8-4

Wistron CA8-4 a.k.a. Ovislink WLA-5000AP

Supported Versions

Version/Model S/N Release Date OpenWrt Version Supported Model Specific Notes
- - Kamikaze 8.09.2 (tested) Setup
- - Attitude Adjustment 12.09 (tested) Setup

The latest out-of-the-box version that can be installed is 12.09 (howto below). Further versions up to 15.05 might run as well, but due to flash size limitations, those need to be manually built.

Hardware Highlights

CPU Flash RAM Network USB Serial JTag
200 Mhz 4MB 32MB 1 x WLAN 11a/b/g No Yes Yes

Hardware

Architecture: MIPS
Vendors used this board layout: Ovislink, Wistron, Airlink
Bootloader: RedBoot
System-On-Chip: Atheros AR2313A
CPU/Speed 200 Mhz
Flash-Chip: SPANSION S29JL032H
Flash size: 4 MB
RAM: 32 MB
RAM Chip: Micron Chips (MT) 48LC8M32B2
Wireless: Atheros AR5112A
Ethernet: within SoC
Internet:
USB: None
Serial: Yes
JTAG: Yes

Board spec

FIXME This hardware description differs from the one shown above. Please consolidate information in the above table, then delete this section (Board spec).tmomas 2015/09/30 13:32

Serial

Populated serial on JP1

VCC = +3.3V

[JTAG connector]

 VCC - []
       ()
  TX - ()
       ()
  RX - ()
 GND - ()

  • baud: 115200
  • 8 bit, 1 stop bit
  • No parity

Software

Standard Ovislink / Airlive firmware

The AP ships with Linux 2.4.18-mips

Boot loader

      ============================================
        AR2313 Boot Loader Interface
        V1.03e00 2006-1-02 (zImage)
      ============================================
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash.
   4: Load calibration data then write to Flash via XModem.
3 seconds time out

Linux boot

  ZImage -CRC = 0x1226dd06
Copying image from flash to SDRAM ...
flash start= 0xbfc50000; flash end= 0xbfe85000
frequence_setup
register_console
min=0:CHIP:AR2313
CPU revision is: 0001800a
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Linux version 2.4.18-mips (root@localhost.localdomain) (gcc version 2.95.4 20010
319 (prerelease)) #2 €­ 4€ë 14 13:27:26 CST 2006
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initial ramdisk at: 0x80343000 (1815109 bytes)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: ip=192.168.1.3:192.168.1.1::netmask::eth0
calculating r4koff... 000dbba0(900000)
Calibrating delay loop... 179.81 BogoMIPS
Memory: 27044k/32768k available (1129k kernel code, 5724k reserved, 1912k data,
4k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xbc000000x (irq = 12) is a 16550A
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 6500K size 1024 blocksize
loop: loaded (max 8 devices)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1772k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 4k freed
Algorithmics/MIPS FPU Emulator v1.5
Bummer, can't write to log on /dev/tty5!
console=/dev/ttyS0
init started:  BusyBox v0.60.5 (2006.04.14-05:26+0000) multi-call binary
Bummer, can't write to log on /dev/tty5!
Starting pid 8, console /dev/ttyS0: '/etc/rc.d/rcS'
Using /lib/modules/2.4.18-mips/eth.o
CE8-1 Eth ver: 3.17e00.2005
Ethernet use flash address
Ethernet For CA8-4
ae531x ethMAC(0)= 00:4f:69:50:ffffffa7:ffffffcf
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth0: duplex 0, link 1
full
3.19.00 macCtl= 0x1010000c    macFlowCtl= 0x00000002
100
  sb = 00 4F 69 50 A7 CF
ether_setup
ae531x ethMAC(1)= 00:4f:69:50:ffffffa7:ffffffce
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth0: Phy Status=ffff
eth1: duplex 0, link 1
full
3.19.00 macCtl= 0x1010000c    macFlowCtl= 0x00000002
100
  sb = 00 4F 69 50 A7 CE
ether_setup
Using /lib/modules/2.4.18-mips/wlan.o
wlan: 0.7.1.1 BETA (Sam Leffler )
Using /lib/modules/2.4.18-mips/ath_hal.o
Warning: loading ath_hal will taint the kernel: non-GPL license - Proprietary
  See http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
ath_hal: 0.9.5.4 BETA (Sam Leffler )
Using /lib/modules/2.4.18-mips/ath_pci.o
ath_pci: 0.8.3.2 BETA (Sam Leffler )
EEPROM version: 0x4008
ar5212EnableRadarDetection() ... ar5212EnableRadarDetection
wlan0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wlan0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wlan0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wlan0: turbo rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wlan0: 802.11 address: 00:4f:69:50:a7:cd
wlan0: Atheros 5212: irq=5
Using /lib/modules/2.4.18-mips/flashapi.o
Bummer, can't write to log on /dev/tty5!
Starting pid 19, console /dev/ttyS0: '/bin/sh'
BusyBox v0.60.5 (2006.04.14-05:26+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#   syslogd: Execute for syslog/udp/514
maxvalidrate=10 11
Connect with ANY channel
* set rd: 33594, cc: 826
Connect with ANY channel
#

OpenWrt

To use OpenWrt Kamikaze, you should change command line config in the default config file:

CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/preinit"

Also change HAL target in the madwifi makefile to ap43

BUS:=PCI
ifneq ($(CONFIG_LINUX_2_6_ATHEROS),)
  BUS:=AHB
  HAL_TARGET:=ap43
endif

Boot loader

A RedBoot bootlader image has to be installed to support Kamikaze build. As of now this can be installed either via the WiliBox images, or via JTAG.

Setup 12.09

+Ethernet eth1: MAC address 80:70:00:fc:9f:c3
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.254, DNS server IP: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005

Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available
FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
^C
RedBoot> fis init -f
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
RedBoot> load -r -v -b 0x80041000 openwrt-atheros-vmlinux.gz
|
Raw file loaded 0x80041000-0x80180fff, assumed entry at 0x80041000
RedBoot> fis create -r 0x80041000 -e 0x80041000 vmlinux.bin.gz

RedBoot> load -r -v -b 0x80041000 openwrt-atheros-root.squashfs        
/                                                                      
Raw file loaded 0x80041000-0x80220fff, assumed entry at 0x80041000     
RedBoot> fis list                                                      
Name              FLASH addr  Mem addr    Length      Entry point      
RedBoot           0xBE000000  0xBE000000  0x00050000  0x00000000       
RedBoot config    0xBE3DF000  0xBE3DF000  0x00001000  0x00000000       
FIS directory     0xBE3D0000  0xBE3D0000  0x0000F000  0x00000000       
vmlinux.bin.gz    0xBE050000  0x80041000  0x00140000  0x80041000       
RedBoot> fis create -b 0x80041000 -f 0xBE1A0000 -l 0x001E0000 -e 0x00000000 rootfs

Setup 8.09

+Ethernet eth1: MAC address 80:70:00:fc:9f:c3
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.254, DNS server IP: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005

Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available
FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
^C
RedBoot> fis init -f
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
RedBoot> fis list
Name              FLASH addr  Mem addr    Length      Entry point
RedBoot           0xBE000000  0xBE000000  0x00050000  0x00000000
RedBoot config    0xBE3DF000  0xBE3DF000  0x00001000  0x00000000
FIS directory     0xBE3D0000  0xBE3D0000  0x0000F000  0x00000000
RedBoot> load -r -v -b 0x80041000 openwrt-atheros-vmlinux.gz
|
Raw file loaded 0x80041000-0x80130fff, assumed entry at 0x80041000
RedBoot> fis create -r 0x80041000 -e 0x80041000 vmlinux.bin.gz
RedBoot> load -r -v -b 0x80041000 openwrt-atheros-root.squashfs
|
Raw file loaded 0x80041000-0x80200fff, assumed entry at 0x80041000
RedBoot> fis create -b 0x80041000 -f 0xBE150000 -l 0x00280000 -e 0x00000000 rootfs
RedBoot> fis list
Name              FLASH addr  Mem addr    Length      Entry point
RedBoot           0xBE000000  0xBE000000  0x00050000  0x00000000
RedBoot config    0xBE3DF000  0xBE3DF000  0x00001000  0x00000000
FIS directory     0xBE3D0000  0xBE3D0000  0x0000F000  0x00000000
vmlinux.bin.gz    0xBE050000  0x80041000  0x000F0000  0x80041000
rootfs            0xBE150000  0xBE150000  0x00280000  0x00000000
RedBoot> fconfig
Run script at boot: true
Boot script:
.. fis load -b 0x80041000 -d vmlinux.bin.gz
.. go
Enter script, terminate with empty line
>> fis load -b 0x80041000 -d vmlinux.bin.gz
>> go
>>
Boot script timeout (1000ms resolution): 3
Use BOOTP for network configuration: false
Gateway IP address:
Local IP address: 192.168.1.1
Local IP address mask: 255.255.255.0
Default server IP address: 192.168.1.254
Console baud rate: 115200
DNS server IP address:
GDB connection port: 9000
Force console for special debug messages: false
Network hardware address [MAC]: 0x80:0x70:0x00:0xFC:0x9F:0xC3
Network debug at boot time: false
Update RedBoot non-volatile configuration - continue (y/n)? y
RedBoot> reset

Boot

+Ethernet eth1: MAC address 80:70:00:fc:9f:c3
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.254, DNS server IP: 0.0.0.0

RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005

Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available
FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
RedBoot> fis load -b 0x80041000 -d vmlinux.bin.gz
Image loaded from 0x80041000-0x80289085
RedBoot> go

Attitude Adjustment 12.09 boot

Ethernet eth1: MAC address 00:11:22:33:44:55                                    
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0                                 
Default server: 192.168.1.254, DNS server IP: 0.0.0.0                           
                                                                                
RedBoot(tm) bootstrap and debug environment [ROM]                               
Non-certified release, version v2_0 - built 14:47:37, Sep 30 2005               
                                                                                
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.                                   
                                                                                
RAM: 0x80000400-0x80800000, 0x80000400-0x807e1000 available                     
FLASH: 0xbe000000 - 0xbe3e0000, 62 blocks of 0x00010000 bytes each.             
== Executing boot script in 5.000 seconds - enter ^C to abort                   
RedBoot> fis load -b 0x80041000 -d vmlinux.bin.gz                               
Image loaded from 0x80041000-0x802fe65c                                         
RedBoot> go                                                                     
[    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc ve
rsion 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 17:43
:48 UTC 2013                                                                    
[    0.000000] gpiochip_add: registered GPIOs 0 to 21 on device: ar5312-gpio    
[    0.000000] ar5312-gpio: registered 22 GPIOs                                 
[    0.000000] bootconsole [early0] enabled                                     
[    0.000000] CPU revision is: 00018009 (MIPS 4Kc)                             
[    0.000000] Determined physical RAM map:                                     
[    0.000000]  memory: 02000000 @ 00000000 (usable)                            
[    0.000000] Initrd not found or empty - disabling initrd                     
[    0.000000] Zone PFN ranges:                                                 
[    0.000000]   Normal   0x00000000 -> 0x00002000                              
[    0.000000] Movable zone start PFN for each node                             
[    0.000000] Early memory PFN ranges                                          
[    0.000000]     0: 0x00000000 -> 0x00002000                                  
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 8128                                                                        
[    0.000000] Kernel command line:  console=ttyS0,9600 rootfstype=squashfs,jffs
2                                                                               
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)               
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)    
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)      
[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.  
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 byt
es                                                                              
[    0.000000] Memory: 29164k/32768k available (2285k kernel code, 3604k reserve
d, 353k data, 168k init, 0k highmem)                                            
[    0.000000] NR_IRQS:128                                                      
[    0.000000] console [ttyS0] enabled, bootconsole disabled                    
[    0.000000] console [ttyS0] enabled, bootconsole disabled                    
[    0.010000] Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)          
[    0.100000] pid_max: default: 32768 minimum: 301                             
[    0.110000] Mount-cache hash table entries: 512                              
[    0.120000] NET: Registered protocol family 16                               
[    0.170000] bio: create slab <bio-0> at 0                                    
[    0.190000] Switching to clocksource MIPS                                    
[    0.210000] NET: Registered protocol family 2                                
[    0.260000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)   
[    0.350000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)  
[    0.430000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)         
[    0.510000] TCP: Hash tables configured (established 1024 bind 1024)         
[    0.580000] TCP reno registered                                              
[    0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes)               
[    0.690000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)          
[    0.770000] NET: Registered protocol family 1                                
[    0.820000] Radio config found at offset 0x1000(0x100)                       
[    0.900000] squashfs: version 4.0 (2009/01/31) Phillip Lougher               
[    0.970000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY
) (c) 2001-2006 Red Hat, Inc.                                                   
[    1.090000] msgmni has been set to 56                                        
[    1.130000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2
54)                                                                             
[    1.220000] io scheduler noop registered                                     
[    1.270000] io scheduler deadline registered (default)                       
[    1.330000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled         
[    1.430000] serial8250: ttyS0 at MMIO 0xbc000003 (irq = 37) is a 16550A      
[    1.530000] gpiodev: gpio device registered with major 253                   
[    1.600000] physmap platform flash device: 00800000 at 1e000000              
[    1.670000] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank. Manufa
cturer ID 0x000001 Chip ID 0x000a00                                             
[    1.800000] Amd/Fujitsu Extended Query Table at 0x0040                       
[    1.860000]   Amd/Fujitsu Extended Query version 1.3.                        
[    1.920000] number of CFI chips: 1                                           
[    1.960000] Searching for RedBoot partition table in physmap-flash.0 at offse
t 0x3d0000                                                                      
[    2.070000] 6 RedBoot partitions found on MTD device physmap-flash.0         
[    2.150000] Creating 6 MTD partitions on "physmap-flash.0":                  
[    2.220000] 0x000000000000-0x000000050000 : "RedBoot"                        
[    2.280000] 0x000000050000-0x000000190000 : "vmlinux.bin.gz"                 
[    2.360000] 0x0000001a0000-0x0000003d0000 : "rootfs"                         
[    2.420000] mtd: partition "rootfs" set to be root filesystem                
[    2.490000] mtd: partition "rootfs_data" created automatically, ofs=350000, l
en=80000                                                                        
[    2.590000] 0x000000350000-0x0000003d0000 : "rootfs_data"                    
[    2.660000] 0x0000003d0000-0x0000003df000 : "FIS directory"                  
[    2.730000] 0x0000003df000-0x0000003e0000 : "RedBoot config"                 
[    2.810000] 0x0000003e0000-0x000000400000 : "boardconfig"                    
[    2.950000] eth0: Atheros AR231x: 00:4f:69:50:17:af, irq 4                   
[    3.090000] ar231x_eth_mii: probed                                           
[    3.130000] eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01)  
[    3.220000] TCP cubic registered                                             
[    3.260000] NET: Registered protocol family 17                               
[    3.310000] Bridge firewalling registered                                    
[    3.360000] 8021q: 802.1Q VLAN Support v1.8                                  
[    3.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. 
[    3.510000] Freeing unused kernel memory: 168k freed                         
[    4.210000] eth0: Configuring MAC for full duplex                            
- preinit -                                                                     
Press the [f] key and hit [enter] to enter failsafe mode                        
- regular preinit -                                                             
[   10.720000] JFFS2 notice: (303) jffs2_build_xattr_subsystem: complete buildin
g xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 2 
orphan) found.                                                                  
switching to jffs2                                                              
- init -                                                                        
                                                                                
Please press Enter to activate this console. [   14.890000] Compat-drivers backp
ort release: compat-drivers-2012-09-04-2-gddac993                               
[   14.980000] Backport based on wireless-testing.git master-2012-09-07         
[   15.060000] compat.git: wireless-testing.git                                 
[   15.170000] cfg80211: Calling CRDA to update world regulatory domain         
[   15.240000] cfg80211: World regulatory domain updated:                       
[   15.300000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp)                                                                    
[   15.400000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   15.500000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   15.590000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   15.680000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   15.770000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   16.950000] ath5k: phy0: Atheros AR5312 chip found (MAC: 0x57, PHY: 0x42)    
[   17.030000] ath5k: phy0: RF5112B multiband radio found (0x36)                
[   17.110000] cfg80211: Calling CRDA for country: US                           
[   17.480000] cfg80211: Regulatory domain changed to country: US               
[   17.550000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp)                                                                    
[   17.650000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 27
00 mBm)                                                                         
[   17.750000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 17
00 mBm)                                                                         
[   17.840000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   17.930000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   18.020000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 20
00 mBm)                                                                         
[   18.120000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 30
00 mBm)                                                                         
[   18.300000] PPP generic driver version 2.4.2                                 
[   18.800000] ip_tables: (C) 2000-2006 Netfilter Core Team                     
[   19.170000] NET: Registered protocol family 24                               
[   19.260000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)               
                                                                                
                                                                                
                                                                                
BusyBox v1.19.4 (2013-03-14 17:30:13 UTC) built-in shell (ash)                  
Enter 'help' for a list of built-in commands.                                   
                                                                                
  _______                     ________        __                                
 |       |.-----.-----.-----.|  |  |  |.----.|  |_                              
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|                             
 |_______||   __|_____|__|__||________||__|  |____|                             
          |__| W I R E L E S S   F R E E D O M                                  
 -----------------------------------------------------                          
 ATTITUDE ADJUSTMENT (12.09, r36088)                                            
 -----------------------------------------------------                          
  * 1/4 oz Vodka      Pour all ingredients into mixing                          
  * 1/4 oz Gin        tin with ice, strain into glass.                          
  * 1/4 oz Amaretto                                                             
  * 1/4 oz Triple sec                                                           
  * 1/4 oz Peach schnapps                                                       
  * 1/4 oz Sour mix                                                             
  * 1 splash Cranberry juice                                                    
 -----------------------------------------------------                          
root@OpenWrt:/# 

Kamikaze 8.09 boot

Linux version 2.6.26.8 (agb@arrakis) (gcc version 4.1.2) #4 Tue Dec 29 14:55:54                                  UTC 2009
CPU revision is: 00018009 (MIPS 4Kc)
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 8192) 0 entries of 256 used
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal          0 ->     8192
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->     8192
On node 0 totalpages: 8192
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,9600 rootfstype=squashfs,jffs2 init=/etc/prei                                 nit
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 128 (order: 7, 512 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29792k/32768k available (1898k kernel code, 2976k reserved, 304k data, 1                                 24k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 219.54 BogoMIPS (lpj=1097728)
Mount-cache hash table entries: 512
net_namespace: 644 bytes
NET: Registered protocol family 16
Radio config found at offset 0x1000(0x100)
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ar531x: Registering GPIODEV device
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xbc000003 (irq = 37) is a 16550A
eth0: Atheros AR231x: 00:4f:69:50:17:af, irq 4
ar2313_eth_mii: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01)
physmap platform flash device: 00800000 at 1e000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
Searching for RedBoot partition table in physmap-flash.0 at offset 0x3d0000
6 RedBoot partitions found on MTD device physmap-flash.0
Creating 6 MTD partitions on "physmap-flash.0":
0x00000000-0x00050000 : "RedBoot"
0x00050000-0x00150000 : "vmlinux.bin.gz"
0x00150000-0x003d0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=100000
0x002d0000-0x003d0000 : "rootfs_data"
0x003d0000-0x003df000 : "FIS directory"
0x003df000-0x003e0000 : "RedBoot config"
0x003e0000-0x00400000 : "boardconfig"
TCP vegas registered
eth0: Configuring MAC for full duplex
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering learning state
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 2009-05-08 (AR5212, AR5312, RF5111, RF5112, RF2316, RF2317, REGOPS_FUNC                                 , TX_DESC_SWAP, XR)
ath_ahb: trunk
wlan: trunk
wlan: mac acl policy registered
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36                                 Mbps 48Mbps 54Mbps
wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
ath_ahb: wifi0: Atheros 5312 WiSoC: mem=0xb8500000, irq=5

Manufacturer:

Access points:

GPL sources:

Tags

toh/wistron/ca8-4.txt · Last modified: 2016/08/16 13:23 by wigyori