User Tools

Site Tools


toh:zbt:wa-05

Table of Contents

ZBT WA-05

OpenWrt support in trunk @r41579

Factory Data Sheet External Link

Hardware

Overview

Architecture: MIPS
Vendor: MediaTek (Ralink)
Bootloader: U-Boot 1.1.3
System-On-Chip: Ralink MT7620N ver:2 eco:3
CPU MIPS 24KEc V5.0
CPU Speed 580 MHz
Flash: 8 MB Winbond 25Q64
RAM: 64 MB Elpida D5116AGTA-6B-E
Wireless: SoC
Ethernet: 10/100
USB: Yes 1x (EHCI,OHCI)

Photos

Bootlog

U-Boot 1.1.3 (Jan 6 2014 - 20:44:06) SoC:MediaTek MT7620 DRAM: Memory Testing..65536K OK. is 64 MB relocate_code Pointer at: 83fac000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. spi_wait_nsec: 14 spi device id: ef 40 17 0 0 (40170000) Flash: W25Q64BV _______________________________________________________________ | ____ _ ____ | | | _ \ __ _ _ __ __| | ___ _ __ __ _| __ ) _____ __ | | | |_) / _` | '_ \ / _` |/ _ \| '__/ _` | _ \ / _ \ \/ / | | | __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) > < | | |_| \__,_|_| |_|\__,_|\___/|_| \__,_|____/ \___/_/\_\ | | | | Ralink/MTK SDK Plantform | | Copyright 2005-2013 | | Board:ZBT WR8305RT | | | | lintel<lintel.huang@gmail.com> | |______________________________________________________________| ===============System Info================== ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Flash component: SPI Flash CPU Speed: 580 MHZ RAM Size:64 Mbytes Build Date:Jan 6 2014 Time:20:44:06 ============================================ GPIO Init: UARTF_SHARE_MODE:GPIO I2C_GPIO_MODE:GPIO GPIO_MODE_REG:0x1a311d ReadyLED Bit:0x1 Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. Press Reset button enter upgrade mode! ## Booting image at bc050000 ... Image Name: MIPS OpenWrt Linux-3.10.49 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1015644 Bytes = 991.8 kB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 3.10.49 (black@black) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41824) ) #1 Thu Jul 24 14:18:41 CDT 2014 [ 0.000000] Board has DDR1 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is Zbtlink ZBT-WA05 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0007f4df [ 0.000000] Readback ErrCtl register=0007f4df [ 0.000000] Memory: 61712k/65536k available (2282k kernel code, 3824k reserved, 550k data, 172k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] pinctrl core: initialized pinctrl subsystem [ 0.070000] NET: Registered protocol family 16 [ 0.090000] bio: create slab <bio-0> at 0 [ 0.100000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.100000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.110000] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.110000] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.120000] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.120000] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.130000] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.130000] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.140000] Switching to clocksource MIPS [ 0.140000] NET: Registered protocol family 2 [ 0.150000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.150000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.160000] TCP: Hash tables configured (established 512 bind 512) [ 0.160000] TCP: reno registered [ 0.160000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.170000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.180000] NET: Registered protocol family 1 [ 0.180000] rt-timer 10000100.timer: maximum frequncy is 2441Hz [ 0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.210000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.220000] msgmni has been set to 120 [ 0.220000] io scheduler noop registered [ 0.230000] io scheduler deadline registered (default) [ 0.230000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.240000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.250000] console [ttyS0] enabled, bootconsole disabled [ 0.250000] console [ttyS0] enabled, bootconsole disabled [ 0.260000] m25p80 spi32766.0: found s25fl064k, expected w25q64 [ 0.270000] m25p80 spi32766.0: s25fl064k (8192 Kbytes) [ 0.280000] 4 ofpart partitions found on MTD device spi32766.0 [ 0.280000] Creating 4 MTD partitions on "spi32766.0": [ 0.290000] 0x000000000000-0x000000030000 : "u-boot" [ 0.290000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.300000] 0x000000040000-0x000000050000 : "factory" [ 0.310000] 0x000000050000-0x0000007b0000 : "firmware" [ 0.310000] 0x000000147f9c-0x0000007b0000 : "rootfs" [ 0.320000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.330000] mtd: device 4 (rootfs) set to be root filesystem [ 0.340000] mtd: partition "rootfs_data" created automatically, ofs=0x3f0000, len=0x3c0000 [ 0.350000] 0x0000003f0000-0x0000007b0000 : "rootfs_data" [ 0.360000] (unregistered net_device): port 1 link up (100Mbps/Full duplex) [ 0.370000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver [ 0.370000] eth0: done loading [ 0.380000] rt3xxx-usbphy ubsphy.3: loaded [ 0.380000] rt2880_wdt 10000120.watchdog: Initialized [ 0.390000] TCP: cubic registered [ 0.390000] NET: Registered protocol family 17 [ 0.400000] 8021q: 802.1Q VLAN Support v1.8 [ 0.410000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.420000] Freeing unused kernel memory: 172K (802c5000 - 802f0000) procd: Console is alive procd: - watchdog - [ 4.440000] usbcore: registered new interface driver usbfs [ 4.440000] usbcore: registered new interface driver hub [ 4.450000] usbcore: registered new device driver usb [ 4.490000] SCSI subsystem initialized [ 4.500000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.510000] ehci-platform: EHCI generic platform driver [ 4.720000] rt3xxx-usbphy ubsphy.3: remote usb device wakeup disabled [ 4.720000] rt3xxx-usbphy ubsphy.3: UTMI 16bit 30MHz [ 4.730000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 4.740000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 4.740000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 4.770000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 4.770000] hub 1-0:1.0: USB hub found [ 4.780000] hub 1-0:1.0: 1 port detected [ 4.780000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.790000] ohci-platform 101c1000.ohci: Generic Platform OHCI Controller [ 4.800000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 4.800000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 4.870000] hub 2-0:1.0: USB hub found [ 4.870000] hub 2-0:1.0: 1 port detected [ 4.880000] leds-gpio gpio-leds.4: pins are not configured from the driver [ 4.900000] usbcore: registered new interface driver usb-storage procd: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level kmod: ran 1 iterations [ 9.110000] jffs2: notice: (309) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (0 unchecked, 18 orphan) and 27 of xref (0 dead, 18 orphan) found. block: extroot: no root or overlay mount defined jffs2 is ready jffs2 is ready [ 9.250000] jffs2: notice: (306) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (0 unchecked, 18 orphan) and 27 of xref (0 dead, 18 orphan) found. switching to overlay procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 10.990000] NET: Registered protocol family 10 [ 11.020000] nf_conntrack version 0.5.0 (966 buckets, 3864 max) [ 11.030000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.050000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 11.060000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 11.070000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.100000] usbcore: registered new interface driver ums-alauda [ 11.110000] usbcore: registered new interface driver ums-cypress [ 11.120000] usbcore: registered new interface driver ums-datafab [ 11.120000] usbcore: registered new interface driver ums-freecom [ 11.130000] usbcore: registered new interface driver ums-isd200 [ 11.140000] usbcore: registered new interface driver ums-jumpshot [ 11.160000] usbcore: registered new interface driver ums-karma [ 11.170000] usbcore: registered new interface driver ums-sddr09 [ 11.170000] usbcore: registered new interface driver ums-sddr55 [ 11.180000] usbcore: registered new interface driver ums-usbat [ 11.210000] xt_time: kernel timezone is -0000 [ 11.240000] cfg80211: Calling CRDA to update world regulatory domain [ 11.240000] cfg80211: World regulatory domain updated: [ 11.250000] cfg80211: DFS Master region: unset [ 11.250000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.260000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.270000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.280000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 11.290000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A) [ 11.290000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.300000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.310000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.320000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 11.370000] PPP generic driver version 2.4.2 [ 11.390000] NET: Registered protocol family 24 [ 11.420000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected [ 11.430000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 18.060000] device eth0.1 entered promiscuous mode [ 18.060000] device eth0 entered promiscuous mode [ 18.090000] br-lan: port 1(eth0.1) entered forwarding state [ 18.090000] br-lan: port 1(eth0.1) entered forwarding state procd: - init complete - [ 20.090000] br-lan: port 1(eth0.1) entered forwarding state [ 20.390000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.390000] device wlan0 entered promiscuous mode [ 20.400000] br-lan: port 2(wlan0) entered forwarding state [ 20.400000] br-lan: port 2(wlan0) entered forwarding state [ 20.410000] br-lan: port 2(wlan0) entered disabled state [ 20.450000] br-lan: port 2(wlan0) entered forwarding state [ 20.450000] br-lan: port 2(wlan0) entered forwarding state [ 20.460000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 22.450000] br-lan: port 2(wlan0) entered forwarding state BusyBox v1.22.1 (2014-07-24 14:03:27 CDT) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r41824) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#


Tags

toh/zbt/wa-05.txt · Last modified: 2015/12/12 08:27 by tmomas