User Tools

Site Tools


toh:zyxel:p-870hn-51b

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:zyxel:p-870hn-51b [2012/10/29 22:55]
toh:zyxel:p-870hn-51b [2014/10/12 12:55] (current)
theoradicus tag phy->nic
Line 1: Line 1:
-====== ZyXEL P-870HN-51b ====== +====== ZyXEL P-870HN-5xb ====== 
-ADSL2/VDSL2 wireless router with 4x100M ethernet ports. Wireless supports ​802.11b/g/n+ 
 +802.11n Wireless VDSL2 4-port Gateway
  
 ===== Supported Versions ===== ===== Supported Versions =====
 +^ Version/​Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^                                                               
 +|**PARTLY SUPPORTED** (router boots up, but some drivers don't work) |||||
  
 +  * Barrier Breaker (14.07):\\ [[https://​downloads.openwrt.org/​barrier_breaker/​14.07-rc3/​brcm63xx/​generic/​openwrt-96368MVWG-generic-squashfs-cfe.bin|openwrt-96368MVWG-generic-squashfs-cfe.bin]]
 +  * Trunk:\\ [[https://​downloads.openwrt.org/​snapshots/​trunk/​brcm63xx/​openwrt-96368MVWG-generic-squashfs-cfe.bin|openwrt-96368MVWG-generic-squashfs-cfe.bin]]
  
 +  Both version have vital bugs:
 +  1) switch - works only two middle FE ports!
 +  2) wireless - bcm43222 isn't recognize !
  
-^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^ +Adsl driver on orginal fw - A2pv6C033a.d23e 
-**NOT SUPPORTED YET**+ 
 +The Board ID is the same as the [[toh/netgear/dgnd3700|Netgear DGND3700 v1]]
  
 ===== Hardware Highlights ===== ===== Hardware Highlights =====
-CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ +model ^ SoC ^ Ram ^ Flash ^ Network ​^ Modem ^ USB ^ Serial ^ JTag ^ 
-Broadcom 4350 V3.1 | 32MiB | 8MiB | | ? | ? |+P-870HN-51b | BCM6368 @400Mhz ​| 32MiB | 8MiB | 4x FE 1x DSL (rj11) | Solder(No) | Yes No? | 
 +| P-870HN-53b | BCM6368 @400Mhz | 64MiB | 8MiB | 4x FE | 1x DSL (rj45) | Solder(No) | Yes | No? | 
 + 
 +Forum thread: https://​forum.openwrt.org/​viewtopic.php?​id=47671 
 + 
 +The Zyxel P-870HW-51a is very similar to this model, but has the following differences:​ 
 + 
 +  - Wireless: BCM4318 B/G. 
 +  - Flash size: 4 MB. 
 +  - VDSL capable only. 
 + 
  
 ===== Hardware ===== ===== Hardware =====
 +Top of the motherboard:​
 +^ P-870HN-51b ^ P-870HN-53b ^
 +|{{media:​zyxel.p-870hn-51b-board-serial.jpg?​500 |P-870HN-51b}}|{{:​media:​p870hn53b_pcb_top_con_owrt.jpg?​500|P-870HN-53b}}|
 +
 +More galleries: wikidevi.com/​wiki/​ZyXEL_P-870HN-51b
 +
 ==== Info ==== ==== Info ====
-| **[[wp>​Instruction set|Architecture]]:​** ​   | [[wp>​MIPS architecture|MIPS]] | +^ ^ P-870HN-51b ^ P-870HN-53b ^ 
-| **Vendor:​** ​         | [[wp>Zyxel]] | +| **[[wp>​Instruction set|Architecture]]:​** ​   |  [[wp>​MIPS architecture|MIPS]] ​ |
-| **[[doc:​techref:​Bootloader]]:​** ​    ​| ​+| **Vendor:​** ​         |  [[wp>Broadcom]]  |
-| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | Broadcom 6368 (based on reference board 96368MVWG+| **[[doc:​techref:​Bootloader]]:​** ​    ​| ​ ​[[doc:​techref:​bootloader:​CFE]] ​ |
-| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​       | BCM4350 V3.1 | +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ |  ​[[http://​wiki.openwrt.org/​_media/​media/​bcm6368_product_brief.pdf|BCM6368]] ​ || 
-| **Flash-Chip:**      | +| **Board ID:**      |  ​96368MVWG ​ |
-| **Flash ​size:**      | 8 MiB +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​       |   ​BCM4350 V3.1 / 400MHz ​ |
-| **RAM:​** ​            | 32 MiB   ​+| **Flash ​size:**      |  8 MiB  |
-| **Wireless:**        | BCM43222 ​+| **Flash-Chip:**      |  ​[[http://​www.macronix.com/​Lists/​DataSheet/​Attachments/​1481/​MX29LV640E%20T-B,​%203V,​%2064Mb,​%20v1.7.pdf|Macronix MX29LV640EBTI-70G]] ​ |
-| **Ethernet:**        4 ports +| **RAM:​** ​            ​| ​ 32 MiB  ​| ​ 64MiB  ​
-| **Internet:**        | ADSL2+/VDSL/​VDSL2 ​ | +| **RAM-Chip:**        |  ​Winbond W9412G6IH-5?​ x2  |  ???  ​
-| **USB:​** ​            ​(no outside connector) | +| **Wireless:**               |  BCM43222KFBG/​ 2x2 MIMO for 2,4GHz 802.11b/​g/​n  ​|| 
-| **[[doc:​hardware:​port.serial|Serial]]:​** ​         +| **[[doc:​hardware:​Switch]]:**     4x FastEthernet10/​100 ​ || 
-| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​           | ?  |+| **[[doc/​hardware/​internet.access.technologies|Modem]]:​** ​  ​|  ​ADSL2+/VDSL2 (physical port RJ11)  |  ADSL2+/​VDSL2 ​(physical port RJ45)  | 
 +| **USB:​** ​                        Yes 2x (SoC[NOT soldered on PCB]  |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​ ​| ​ [[#​Serial|Yes]]  ​|| 
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​      Seems no   || 
 +| **FCC ID:**        |  I88P870HN51B ​ |    | 
 + 
 + 
 +==== Logs ==== 
 +<​code>​ 
 +CFE version 1.0.37-107.23 for BCM96368 (32bit,​SP,​BE) 
 +Build Date: 12/27/2011 (FuChia@MsgSW4-SerVer) 
 +Copyright (C) 2000-2009 Broadcom Corporation. 
 + 
 +Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB 
 +Total Flash size: 8192K with 135 sectors 
 +Chip ID: BCM6368B2, MIPS: 400MHz 
 +Main Thread: TP0 
 +Total Memory: 33554432 bytes (32MB) 
 +Boot Address: 0xb8000000 
 + 
 +Checking Reset button on EXT INTR 0 
 +Checking Reset button on EXT INTR 0 
 +Board IP address ​                 : 192.168.1.1:​ffffff00 
 +Host IP address ​                  : 192.168.1.100 
 +Gateway IP address ​               : 
 +Run from flash/host (f/h)         : f 
 +Default host run file name        : vmlinux 
 +Default host flash file name      : bcm963xx_fs_kernel 
 +Boot delay (0-9 seconds) ​         : 3 
 +Board Id (0-15) ​                  : 96368MVWG 
 +Number of MAC Addresses (1-32) ​   : 10 
 +Base MAC Address ​                 : c8:​6c:​87:​5c:​11:​a9 
 +PSI Size (1-128) KBytes ​          : 64 
 +Enable Backup PSI [0|1]           : 1 
 +System Log Size (0-256) KBytes ​   : 0 
 +Main Thread Number [0|1]          : 0 
 + 
 +*** Press any key to stop auto run (3 seconds) *** 
 +Auto run second count down: 0 
 +Wait for Multiboot Service Packet... ​ 0 
 +Booting from only image (0xb8010000) ... 
 +Code Address: 0x80010000, Entry Address: 0x80222300 
 +Decompression OK! 
 +Entry at 0x80222300 
 +Closing network. 
 +Disabling Switch ports. 
 +Flushing Receive Buffers... 
 +0 buffers found. 
 +Closing DMA Channels. 
 +Starting program at 0x80222300 
 +Linux version 2.6.30 (FuChia@MsgSW4-SerVer) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 Wed Jan 4 11:38:27 CST 2012 
 +Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB 
 +96368MVWG prom init 
 +CPU revision is: 0002a031 (Broadcom4350) 
 +Determined physical RAM map: 
 + ​memory:​ 01f00000 @ 00000000 (usable) 
 +Zone PFN ranges: 
 +  DMA      0x00000000 -> 0x00001000 
 +  Normal ​  ​0x00001000 -> 0x00001f00 
 +Movable zone start PFN for each node 
 +early_node_map[1] active PFN ranges 
 +    0: 0x00000000 -> 0x00001f00 
 +On node 0 totalpages: 7936 
 +free_area_init_node:​ node 0, pgdat 80295c20, node_mem_map 81000000 
 +  DMA zone: 32 pages used for memmap 
 +  DMA zone: 0 pages reserved 
 +  DMA zone: 4064 pages, LIFO batch:0 
 +  Normal zone: 30 pages used for memmap 
 +  Normal zone: 3810 pages, LIFO batch:0 
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 7874 
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200 
 +wait instruction:​ enabled 
 +Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. 
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes 
 +RCU-based detection of stalled CPUs is enabled. 
 +NR_IRQS:​128 
 +PID hash table entries: 128 (order: 7, 512 bytes) 
 +console [ttyS0] enabled 
 +Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) 
 +Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) 
 +Memory: 28516k/​31744k available (2144k kernel code, 3228k reserved, 445k data, 116k init, 0k highmem) 
 +Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) 
 +Mount-cache hash table entries: 512 
 +net_namespace:​ 816 bytes 
 +NET: Registered protocol family 16 
 +Total Flash size: 8192K with 135 sectors 
 +registering PCI controller with io_map_base unset 
 +bio: create slab <​bio-0>​ at 0 
 +pci 0000:​00:​01.0:​ reg 10 32bit mmio: [0x000000-0x00ffff] 
 +BLOG v2.1 Initialized 
 +NET: Registered protocol family 8 
 +NET: Registered protocol family 20 
 +NET: Registered protocol family 2 
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +TCP established hash table entries: 1024 (order: 1, 8192 bytes) 
 +TCP bind hash table entries: 1024 (order: 0, 4096 bytes) 
 +TCP: Hash tables configured (established 1024 bind 1024) 
 +TCP reno registered 
 +NET: Registered protocol family 1 
 +squashfs: version 4.0 (2009/​01/​31) Phillip Lougher 
 +squashfs: version 4.0 with LZMA457 ported by BRCM 
 +msgmni has been set to 55 
 +io scheduler noop registered (default) 
 +PPP generic driver version 2.4.2 
 +PPP Deflate Compression module registered 
 +PPP BSD Compression module registered 
 +NET: Registered protocol family 24 
 +bcm963xx_mtd driver v1.0 
 +File system address: 0xb8010100 
 +brcmboard: brcm_board_init entry 
 +SES: Button Interrupt 0x1 is enabled 
 +SES: LED GPIO 0x8018 is enabled 
 +Serial: BCM63XX driver $Revision: 3.00 $ 
 +ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX 
 +ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX 
 +bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Jan  4 2012 11:12:01 
 +Broadcom Logger v0.1 Jan  4 2012 11:11:09 
 +Mirror/​redirect action on 
 +u32 classifier 
 +    input device check on 
 +    Actions configured 
 +TCP cubic registered 
 +Initializing XFRM netlink socket 
 +NET: Registered protocol family 17 
 +NET: Registered protocol family 15 
 +Initializing MCPD Module 
 +Ebtables v2.0 registered 
 +ebt_time registered 
 +ebt_ftos registered 
 +ebt_wmm_mark registered 
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​ 
 +All bugs added by David S. Miller <​davem@redhat.com>​ 
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:0. 
 +Freeing unused kernel memory: 116k freed 
 +init started: ​ BusyBox v1.00 (2012.01.04-03:​14+0000) multi-call binary 
 + 
 + 
 +BusyBox v1.00 (2012.01.04-03:​14+0000) Built-in shell (msh) 
 +Enter '​help'​ for a list of built-in commands. 
 + 
 + 
 +Loading drivers and kernel modules... 
 + 
 +pktflow: module license '​Proprietary'​ taints kernel. 
 +Disabling lock debugging due to kernel taint 
 +Broadcom Packet Flow Cache  Char Driver v2.1 Jul 15 2010 09:29:38 Registered<​242>​ 
 +NBUFF v1.0 Initialized 
 +Broadcom Packet Flow Cache learning via BLOG enabled. 
 +Created Proc FS /​procfs/​fcache 
 +Broadcom Packet Flow Cache registered with netdev chain 
 +Constructed Broadcom Packet Flow Cache v2.1 Jul 15 2010 09:29:37 
 +Broadcom Packet CMF (Experimental) Char Driver v0.1 Jul 15 2010 09:29:34 Registered<​232>​ 
 +Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jul 15 2010 09:29:33 Loaded 
 +bcmxtmcfg: bcmxtmcfg_init entry 
 +adsl: adsl_init entry 
 +Broadcom BCM6368B2 Ethernet Network Device v0.1 Jan  4 2012 11:11:15 
 +ETH Init: 180 tx BDs at 0xa18d4000 
 +ETH Init: 180 tx BDs at 0xa199c000 
 +ETH Init: 400 rx BDs at 0xa19eb000 
 +ETH Init: 400 rx BDs at 0xa19fb000 
 +dgasp: kerSysRegisterDyingGaspHandler:​ bcmsw registered 
 +Broadcom Packet CMF (Experimental) SWC RESET. 
 +Broadcom Packet CMF (Experimental) SWC INITIALIZED. 
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 15 2010 09:29:35 Registered 
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 15 2010 09:29:35 Registered 
 +Broadcom Packet CMF (Experimental) ENABLED. 
 +eth0: MAC Address: C8:​6C:​87:​5C:​11:​A9 
 +eth1: MAC Address: C8:​6C:​87:​5C:​11:​A9 
 +eth2: MAC Address: C8:​6C:​87:​5C:​11:​A9 
 +eth3: MAC Address: C8:​6C:​87:​5C:​11:​A9 
 +eth4: MAC Address: C8:​6C:​87:​5C:​11:​A9 
 +PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002) 
 +PCI: Setting latency timer of device 0000:​00:​01.0 to 64 
 +wl:srom not detected,​using main memory mapped srom info(wombo board) 
 +wl:loading /​etc/​wlan/​bcm43222_map.bin 
 +wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.60.120.11.cpe4.06L02.1 
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered 
 +IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs 
 +p8021ag: p8021ag_init entry 
 +Broadcom 802.1Q VLAN Interface, v0.1 
 + 
 +===== Release Version 4.06L.02 (build timestamp 120104_1421) ===== 
 + 
 +Sun Jan  1 00:00:00 UTC 2012 
 +update Persistent size = 24029, offset = 0 
 +update BackupPsi size = 24029, offset = 0 
 +ip_tables: (C) 2000-2006 Netfilter Core Team 
 +Netfilter messages via NETLINK v0.30. 
 +nf_conntrack version 0.5.0 (1024 buckets, 4096 max) 
 +dhcpd:​error:​12.771:​set_iface_config_defaults:​621:​SIOCGIFADDR failed on br0! 
 +xt_time: kernel timezone is -0000 
 +iptables: Bad rule (does a matching rule exist in that chain?
 +Sntp: Using new rule EST5EDT,​M3.2.0/​2,​M11.1.0/​2 
 +device eth0.0 entered promiscuous mode 
 +device eth0 entered promiscuous mode 
 +br0: port 1(eth0.0) entering forwarding state 
 +device eth0 is not a slave of br0 
 +Created new Tag Rule: dev=eth0, dir=1, tags=0, id=0 
 + 
 +Created new Tag Rule: dev=eth0, dir=1, tags=1, id=0 
 + 
 +Created new Tag Rule: dev=eth0, dir=1, tags=2, id=0 
 + 
 +Broadcom Packet Flow Cache flushing the flows 
 +device eth1.0 entered promiscuous mode 
 +device eth1 entered promiscuous mode 
 +br0: port 2(eth1.0) entering forwarding state 
 +device eth1 is not a slave of br0 
 +Created new Tag Rule: dev=eth1, dir=1, tags=0, id=0 
 + 
 +Created new Tag Rule: dev=eth1, dir=1, tags=1, id=0 
 + 
 +Created new Tag Rule: dev=eth1, dir=1, tags=2, id=0 
 + 
 +Broadcom Packet Flow Cache flushing the flows 
 +device eth2.0 entered promiscuous mode 
 +device eth2 entered promiscuous mode 
 +br0: port 3(eth2.0) entering forwarding state 
 +device eth2 is not a slave of br0 
 +Created new Tag Rule: dev=eth2, dir=1, tags=0, id=0 
 + 
 +Created new Tag Rule: dev=eth2, dir=1, tags=1, id=0 
 + 
 +Created new Tag Rule: dev=eth2, dir=1, tags=2, id=0 
 + 
 +Broadcom Packet Flow Cache flushing the flows 
 +device eth3.0 entered promiscuous mode 
 +device eth3 entered promiscuous mode 
 +br0: port 4(eth3.0) entering forwarding state 
 +device eth3 is not a slave of br0 
 +Created new Tag Rule: dev=eth3, dir=1, tags=0, id=0 
 + 
 +Created new Tag Rule: dev=eth3, dir=1, tags=1, id=0 
 + 
 +Created new Tag Rule: dev=eth3, dir=1, tags=2, id=0 
 + 
 +Broadcom Packet Flow Cache flushing the flows 
 +WLmngr Daemon is running 
 +optarg=0 shmId=0 
 +BcmAdsl_Initialize=0xC00F8E2C,​ g_pFnNotifyCallback=0xC0128AF4 
 +wlevt_init@107:​ opened loopback socket 4 
 +wlevt is ready for new msg... 
 +Clocks for QPROC and AFE are being aligned with step through ... 
 +AFE is aligned, i = 067, PhaseValue = -050, PhaseCntl = 0x3FBD0000 
 +QPROC is aligned, i = 068, PhaseValue = -150, PhaseCntl = 0x3FBD7FBD 
 +Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x78 
 +AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f 
 +QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f 
 +pSdramPHY=0xA1FFFFF8,​ 0x11541401 0x572DBFEF 
 +*** XfaceOffset:​ 0x5FF90 => 0x5FF90 *** 
 +*** PhySdramSize got adjusted: 0xBDAC0 => 0xEB1E0 *** 
 +AdslCoreSharedMemInit:​ shareMemAvailable=85504 
 +AdslCoreHwReset:​ pLocSbSta=80428000 bkupThreshold=3072 
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA1FB3438 
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered 
 +XTM Init: 400 rx BDs at 0xa09bd000 
 +XTM Init: 100 rx BDs at 0xa0917800 
 + 
 + ​PROGRAM : VcAutoHunt main > ENTER 
 +/​var/​cert/​acscert2.cacert:​ cannot open 
 +ln: /​var/​cert/​bdbefb5f.0:​ File exists 
 +Broadcom Packet CMF (Experimental) ENABLED. 
 +Broadcom Packet Flow Cache learning via BLOG enabled. 
 +Broadcom Packet Flow Cache flushing the flows 
 +monitor task is initialized pid= 191 
 +General UPnP daemon is ready to run with NATT 1 
 +Switch MDK: num_switches = 1 
 +Switch MDK: unit = 0; phy_pbmp = 0x1f; config_pbmp = 0x1f 
 +Switch MDK link poll thread: unit=0; phypbmp=0x1f 
 +eth4 Link UP -1 mbps half duplex 
 +update Persistent size = 24029, offset = 0 
 +update BackupPsi size = 24029, offset = 0 
 +update Persistent size = 23956, offset = 0 
 +update BackupPsi size = 23956, offset = 0 
 +There is no Predefined DevicePin in CFE 
 +WPS Device PIN = 17258227 
 +Setting SSID: "​FrontierHSI"​ 
 +Setting SSID: "​wl0_Guest1"​ 
 +Setting SSID: "​wl0_Guest2"​ 
 +Setting SSID: "​wl0_Guest3"​ 
 +</​code>​ 
 + 
 +<​code>​ 
 +version 
 +Frontier P-870HN-51b 
 +Login: admin 
 +Password: 
 +update Persistent size = 24303, offset = 0 
 +update BackupPsi size = 24303, offset = 0 
 + > cat /​proc/​cpuinfo 
 +system type             : 96368MVWG 
 +processor ​              : 0 
 +cpu model               : Broadcom4350 V3.1 
 +BogoMIPS ​               : 399.36 
 +wait instruction ​       : yes 
 +microsecond timers ​     : yes 
 +tlb_entries ​            : 32 
 +extra interrupt vector ​ : no 
 +hardware watchpoint ​    : no 
 +ASEs implemented ​       : 
 +shadow register sets    : 1 
 +core                    : 0 
 +VCED exceptions ​        : not available 
 +VCEI exceptions ​        : not available 
 + 
 +unaligned exceptions ​           : 21 
 + >​ 
 +</​code>​ 
 + 
 +<​code>​ 
 + > cat /​proc/​version 
 +Linux version 2.6.30 (FuChia@MsgSW4-SerVer) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 Wed Jan 4 11:38:27 CST 2012 
 + > free 
 +consoled:​error:​333.883:​processInput:​507:​unrecognized command free 
 + > Line 0: xDSL G.994 training 
 +cat /​proc/​meminfo Line 0: ADSL link down 
 +bcmxtmcfg: XTM Link Information,​ portid = 0, State = DOWN, Service Support = PTM 
 +Broadcom Packet CMF (Experimental) SWC FLUSHED. 
 +bcmxtmcfg: Reinitialize port 0 traffictype 2 
 +bcmxtmcfg: Normal(XTM/​PTM) Mode enabled 
 + 
 +MemTotal: ​         28632 kB 
 +MemFree: ​           1868 kB 
 +Buffers: ​           2696 kB 
 +Cached: ​            8772 kB 
 +SwapCached: ​           0 kB 
 +Active: ​            3804 kB 
 +Inactive: ​          9948 kB 
 +Active(anon): ​       904 kB 
 +Inactive(anon): ​    1380 kB 
 +Active(file): ​      2900 kB 
 +Inactive(file): ​    8568 kB 
 +SwapTotal: ​            0 kB 
 +SwapFree: ​             0 kB 
 +Dirty: ​                0 kB 
 +Writeback: ​            0 kB 
 +AnonPages: ​         2304 kB 
 +Mapped: ​            2916 kB 
 +Slab:               9260 kB 
 +SReclaimable: ​       420 kB 
 +SUnreclaim: ​        8840 kB 
 +PageTables: ​         280 kB 
 +NFS_Unstable: ​         0 kB 
 +Bounce: ​               0 kB 
 +WritebackTmp: ​         0 kB 
 +CommitLimit: ​      14316 kB 
 +Committed_AS: ​      6308 kB 
 +VmallocTotal: ​   1032148 kB 
 +VmallocUsed: ​       3420 kB 
 +VmallocChunk: ​   1022260 kB 
 + > cat /proc/mtd 
 +dev:    size   ​erasesize ​ name 
 +mtd0: 0049a000 0049a000 "​Physically mapped flash"​ 
 + > cat /​proc/​interrupts 
 +           ​CPU0 
 +  7:     ​364626 ​        ​BCM63xx ​ timer 
 + ​10: ​       324         ​BCM63xx ​ brcm_10 
 + ​12: ​      ​2789 ​        ​BCM63xx ​ brcm_12 
 + ​21: ​         0         ​BCM63xx ​ brcm_21 
 + ​22: ​         0         ​BCM63xx ​ brcm_22 
 + ​23: ​         0         ​BCM63xx ​ brcm_23 
 + ​28: ​         0         ​BCM63xx ​ brcm_28 
 + ​29: ​         0         ​BCM63xx ​ brcm_29 
 + ​40: ​         0         ​BCM63xx ​ brcm_40 
 + ​41: ​         0         ​BCM63xx ​ brcm_41 
 + ​42: ​         0         ​BCM63xx ​ brcm_42 
 + ​48: ​         0         ​BCM63xx ​ brcm_48 
 + ​49: ​         0         ​BCM63xx ​ brcm_49 
 + ​50: ​         0         ​BCM63xx ​ brcm_50 
 + 
 +ERR:          0 
 + > dmesg 
 +consoled:​error:​370.114:​processInput:​507:​unrecognized command dmesg 
 + >​ 
 +</​code>​ 
 + 
 +<​code>​ 
 + > help 
 +
 +help 
 +logout 
 +exit 
 +quit 
 +reboot 
 +df 
 +meminfo 
 +kill 
 +echo 
 +ifconfig 
 +ping 
 +ps 
 +pwd 
 +sysinfo 
 +tftp 
 +wlctl 
 +arp 
 +lan 
 +lanhosts 
 +restoredefault 
 +save 
 +swversion 
 +wlan 
 +tr064 
 +cfm 
 +vcautohunt 
 +dhcpcondserv 
 +captiveurl 
 + > meminfo 
 +Total MDM Shared Memory Region : 1024KB 
 +Shared Memory Usable ​          : 000929KB 
 +Shared Memory in-use ​          : 000117KB 
 +Shared Memory free             : 000812KB 
 +Shared Memory allocs ​          : 023067 
 +Shared Memory frees            : 021132 
 +Shared Memory alloc/free delta : 001935 
 + 
 +Heap bytes in-use ​    : 000016 
 +Heap allocs ​          : 000914 
 +Heap frees            : 000913 
 +Heap alloc/free delta : 000001 
 + > ifconfig 
 +bcmsw           Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​1000 
 +                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) 
 +                Base address:​0x6a00 
 + 
 +br0             Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                inet addr:​192.168.254.254 ​ Bcast:​192.168.254.255 ​ Mask:​255.255.255.0 
 +                UP BROADCAST RUNNING ALLMULTI MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:0 (0.0 B)  TX bytes:9646 (9.4 KiB) 
 + 
 +eth0            Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​1000 
 +                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) 
 + 
 +eth0.0 ​         Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:38 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:0 (0.0 B)  TX bytes:9706 (9.4 KiB) 
 + 
 +eth1            Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​1000 
 +                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) 
 + 
 + 
 +eth1.0 ​         Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:36 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:0 (0.0 B)  TX bytes:9586 (9.3 KiB) 
 + 
 +eth2            Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​1000 
 +                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) 
 + 
 + 
 +eth2.0 ​         Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:34 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:0 (0.0 B)  TX bytes:9466 (9.2 KiB) 
 + 
 +eth3            Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​1000 
 +                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) 
 + 
 + 
 +eth3.0 ​         Link encap:​Ethernet ​ HWaddr C8:​6C:​87:​5C:​11:​A9 
 +                UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:0 (0.0 B)  TX bytes:9346 (9.1 KiB) 
 + 
 +lo              Link encap:Local Loopback 
 +                inet addr:​127.0.0.1 ​ Mask:​255.0.0.0 
 +                UP LOOPBACK RUNNING ​ MTU:​16436 ​ Metric:1 
 +                RX packets:90 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:90 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:6606 (6.4 KiB)  TX bytes:6606 (6.4 KiB) 
 + 
 +sar             Link encap:​UNSPEC ​ HWaddr FE-FF-FF-FF-FF-FF-FF-FF-00-00-00-00-00-00-00-00 
 +                UP NOTRAILERS RUNNING NOARP  MTU:0  Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) 
 +                Interrupt:​50 Base address:​0x5220 
 + 
 +swc             Link encap:​UNSPEC ​ HWaddr FE-FF-FF-FF-FF-FF-FF-FF-00-00-00-00-00-00-00-00 
 +                UP NOTRAILERS RUNNING NOARP  MTU:0  Metric:1 
 +                RX packets:0 errors:0 dropped:0 overruns:0 frame:0 
 +                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 
 +                collisions:​0 txqueuelen:​0 
 +                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B) 
 +                Interrupt:​42 Base address:​0x6a40 
 + 
 + > sysconfig 
 +consoled:​error:​175.526:​processInput:​507:​unrecognized command sysconfig 
 + > sysinfo 
 +Number of processes: 42 
 + ​12:​03am ​ up 3 min, 
 +load average: 1 min:0.03, 5 min:0.07, 15 min:0.03 
 +              total         ​used ​        ​free ​      ​shared ​     buffers 
 +  Mem:        28632        26536         ​2096 ​           0         ​2696 
 + ​Swap: ​           0            0            0 
 +Total: ​       28632        26536         ​2096 
 + > swversion 
 +Usage: swversion show 
 +       ​swversion help 
 + > swversion show 
 +1.10(VFS.0)b3 
 + >​ 
 +</​code>​ 
 + 
 +<​code>​ 
 +CFE> athe 
 +Available commands: 
 + 
 +ATSE                show the seed of password generator 
 +ATEN                set BootExtension Debug Flag 
 +ATSH                dump manufacturer related data in ROM 
 +ATER                Erase ROM-D partition 
 +ATBR                Reset to default Romfile 
 +ATGO                boot router 
 +ATSR                system reboot 
 +ATHE                print help 
 + 
 +For more information about a command, enter 'help command-name'​ 
 +*** command status = 0 
 +CFE> 
 +</​code>​ 
 + 
 +<​code>​ 
 +CFE> ATSH                dump manufacturer related data in ROM 
 + 
 +ZLD      Version ​      : V1.10(VFS.0)b3 
 +Bootbase Version ​      : V1.34 12/27/2011 22:37:03 
 +Vendor Name            : Frontier Communications Corp. 
 +Product Model          : P-870HN-51b 
 +Serial Number ​         : S110Y44018146 
 +First MAC Address ​     : C86C875C11A9 
 +Last MAC Address ​      : C86C875C11B2 
 +MAC Address Quantity ​  : 10 
 +Default Country Code   : FF 
 +Boot Module Debug Flag : 00 
 +RootFS ​     Checksum ​  : 65ee40b7 
 +Kernel ​     Checksum ​  : d71645ce 
 +RomFile ​    ​Checksum ​  : eba9b27e 
 +ImageDefaultChecksum ​  : 54f14a56 
 +Main Feature Bits      : 00 
 +Other Feature Bits     : 
 +                5a 59 40 16 00 00 00 00-00 00 00 00 00 00 00 00 
 +                00 00 00 00 00 00 00 00-00 00 00 00 00 00 
 +</​code>​ 
 + 
 +Openwrt bootlog 
 + 
 +<​code>​ 
 + > tftp 
 +BusyBox v1.00 (2012.01.04-03:​14+0000) multi-call binary 
 + 
 +Usage: tftp [-p|-g] [-t i|c] [-f filename] tftp_server_ip 
 + 
 +Update firmware image and configuration data from OR backup configuration 
 +data to a tftp server. 
 + 
 +Examples: 
 +-g -t i -f filename server_ip ​  Get (flash) broadcom or whole image to modem 
 +-g -t c -f filename server_ip ​  Get (flash) config file to modem 
 +-p -f filename server_ip ​       Put (backup) config file to tftpd server 
 + 
 + 
 + > tftp -g -t i -f openwrt-96368MVWG-generic-squashfs-cfe.bin 192.168.254.33 
 +exit mcpd!! 
 +MemTotal: ​         28632 kB 
 +MemFree: ​          11364 kB 
 +Buffers: ​            152 kB 
 +Cached: ​            2908 kB 
 +SwapCached: ​           0 kB 
 +Active: ​            2336 kB 
 +Inactive: ​          2216 kB 
 +Active(anon): ​       628 kB 
 +Inactive(anon): ​     864 kB 
 +Active(file): ​      1708 kB 
 +Inactive(file): ​    1352 kB 
 +SwapTotal: ​            0 kB 
 +SwapFree: ​             0 kB 
 +Dirty: ​                0 kB 
 +Writeback: ​            0 kB 
 +AnonPages: ​         1512 kB 
 +Mapped: ​            2636 kB 
 +Slab:               9088 kB 
 +SReclaimable: ​       264 kB 
 +SUnreclaim: ​        8824 kB 
 +PageTables: ​         184 kB 
 +NFS_Unstable: ​         0 kB 
 +Bounce: ​               0 kB 
 +WritebackTmp: ​         0 kB 
 +CommitLimit: ​      14316 kB 
 +Committed_AS: ​      3960 kB 
 +VmallocTotal: ​   1032148 kB 
 +VmallocUsed: ​       3420 kB 
 +VmallocChunk: ​   1022260 kB 
 +Allocating 8388628 bytes for flash image. 
 +Memory allocated 
 +Got image via tftp, total image size: 3276804 
 +tftp:​error:​556.544:​verifyZyXELModelId:​143:​Not find ZyXEL identify, just fall through 
 +Flashing root file system and kernel... 
 +.................................................... 
 + 
 +****** DDR->​DSLCorePhaseCntl=0 ****** 
 + 
 +ý 
 + 
 +CFE version 1.0.37-107.23 for BCM96368 (32bit,​SP,​BE) 
 +Build Date: 12/27/2011 (FuChia@MsgSW4-SerVer) 
 +Copyright (C) 2000-2009 Broadcom Corporation. 
 + 
 +Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB 
 +Total Flash size: 8192K with 135 sectors 
 +Chip ID: BCM6368B2, MIPS: 400MHz 
 +Main Thread: TP0 
 +Total Memory: 33554432 bytes (32MB) 
 +Boot Address: 0xb8000000 
 + 
 +Checking Reset button on EXT INTR 0 
 +Checking Reset button on EXT INTR 0 
 +Board IP address ​                 : 192.168.1.1:​ffffff00 
 +Host IP address ​                  : 192.168.1.100 
 +Gateway IP address ​               : 
 +Run from flash/host (f/h)         : f 
 +Default host run file name        : vmlinux 
 +Default host flash file name      : bcm963xx_fs_kernel 
 +Boot delay (0-9 seconds) ​         : 3 
 +Board Id (0-15) ​                  : 96368MVWG 
 +Number of MAC Addresses (1-32) ​   : 10 
 +Base MAC Address ​                 : c8:​6c:​87:​5c:​11:​a9 
 +PSI Size (1-128) KBytes ​          : 64 
 +Enable Backup PSI [0|1]           : 1 
 +System Log Size (0-256) KBytes ​   : 0 
 +Main Thread Number [0|1]          : 0 
 + 
 +*** Press any key to stop auto run (3 seconds) *** 
 +Auto run second count down: 0 
 +Wait for Multiboot Service Packet... ​ 0 
 +Booting from only image (0xb8010000) ... 
 +Code Address: 0x80010000, Entry Address: 0x80010000 
 +LZMA: Prossible old LZMA format, trying to decompress.. 
 +Decompression OK! 
 +Entry at 0x80010000 
 +Closing network. 
 +Disabling Switch ports. 
 +Flushing Receive Buffers... 
 +1 buffers found. 
 +Closing DMA Channels. 
 +Starting program at 0x80010000 
 +[    0.000000] Linux version 3.10.21 (thepeople@trabant) (gcc version 4.6.4 (OpenWrt/​Linaro GCC 4.6-2013.05 r38990) ) #1 Tue Dec 3 08:27:54 CET 2013 
 +[    0.000000] Detected Broadcom 0x6368 CPU revision b2 
 +[    0.000000] CPU frequency is 400 MHz 
 +[    0.000000] 32MB of RAM installed 
 +[    0.000000] registering 38 GPIOs 
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000 
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-107.23 
 +[    0.000000] bootconsole [early0] enabled 
 +[    0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350) 
 +[    0.000000] board_bcm963xx:​ board name: 96368MVWG 
 +[    0.000000] Determined physical RAM map: 
 +[    0.000000] ​ memory: 02000000 @ 00000000 (usable) 
 +[    0.000000] Initrd not found or empty - disabling initrd 
 +[    0.000000] Zone ranges: 
 +[    0.000000] ​  ​Normal ​  [mem 0x00000000-0x01ffffff] 
 +[    0.000000] Movable zone start for each node 
 +[    0.000000] Early memory node ranges 
 +[    0.000000] ​  ​node ​  0: [mem 0x00000000-0x01ffffff] 
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. 
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128 
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200 
 +[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes) 
 +[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) 
 +[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) 
 +[    0.000000] Memory: 28752k/​32768k available (2440k kernel code, 4016k reserved, 704k data, 244k init, 0k highmem) 
 +[    0.000000] NR_IRQS:​128 
 +[    0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) 
 +[    0.032000] pid_max: default: 32768 minimum: 301 
 +[    0.036000] Mount-cache hash table entries: 512 
 +[    0.044000] NET: Registered protocol family 16 
 +[    0.052000] registering PCI controller with io_map_base unset 
 +[    0.056000] registering PCI controller with io_map_base unset 
 +[    0.064000] bio: create slab <​bio-0>​ at 0 
 +[    0.068000] PCI host bridge to bus 0000:00 
 +[    0.072000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] 
 +[    0.076000] pci_bus 0000:00: root bus resource [io  0x8000000-0x8007fff] 
 +[    0.080000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] 
 +[    0.096000] pci 0000:​00:​01.0:​ BAR 0: assigned [mem 0x30000000-0x30003fff] 
 +[    0.100000] PCI host bridge to bus 0000:01 
 +[    0.104000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff] 
 +[    0.108000] pci_bus 0000:01: root bus resource [io  0x8008000-0x800ffff] 
 +[    0.112000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] 
 +[    0.116000] pci 0000:​01:​1e.0:​ bridge configuration invalid ([bus 00-00]), reconfiguring 
 +[    0.120000] pci 0000:​01:​1e.0:​ BAR 10: assigned [mem 0x38000000-0x3fffffff] 
 +[    0.124000] pci 0000:​01:​1e.0:​ BAR 7: assigned [io  0x8008000-0x80080ff] 
 +[    0.128000] pci 0000:​01:​1e.0:​ BAR 8: assigned [io  0x8008400-0x80084ff] 
 +[    0.132000] pci 0000:​01:​1e.0:​ CardBus bridge to [bus 02-05] 
 +[    0.136000] pci 0000:​01:​1e.0: ​  ​bridge window [io  0x8008000-0x80080ff] 
 +[    0.140000] pci 0000:​01:​1e.0: ​  ​bridge window [io  0x8008400-0x80084ff] 
 +[    0.144000] pci 0000:​01:​1e.0: ​  ​bridge window [mem 0x38000000-0x3fffffff] 
 +[    0.148000] PCI: Enabling device 0000:​01:​1e.0 (0000 -> 0003) 
 +[    0.152000] Switching to clocksource MIPS 
 +[    0.160000] PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002) 
 +[    0.188000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 
 +[    0.252000] ssb: Sonics Silicon Backplane found on PCI device 0000:​00:​01.0 
 +[    0.260000] NET: Registered protocol family 2 
 +[    0.264000] TCP established hash table entries: 512 (order: 0, 4096 bytes) 
 +[    0.272000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) 
 +[    0.280000] TCP: Hash tables configured (established 512 bind 512) 
 +[    0.284000] TCP: reno registered 
 +[    0.288000] UDP hash table entries: 256 (order: 0, 4096 bytes) 
 +[    0.296000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) 
 +[    0.304000] NET: Registered protocol family 1 
 +[    0.308000] audit: initializing netlink socket (disabled) 
 +[    0.316000] type=2000 audit(0.316:​1):​ initialized 
 +[    0.320000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher 
 +[    0.324000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
 +[    0.336000] msgmni has been set to 56 
 +[    0.340000] io scheduler noop registered 
 +[    0.344000] io scheduler deadline registered (default) 
 +Ę[    0.360000] console [ttyS0] enabled, bootconsole disabled= 10) is a bcm63xx_uart 
 +[    0.360000] console [ttyS0] enabled, bootconsole disabled 
 +[    0.372000] bcm63xx-rng bcm63xx-rng:​ registered RNG driver 
 +[    0.380000] physmap platform flash device: 08000000 at 18000000 
 +[    0.384000] physmap-flash.0:​ Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb 
 +[    0.396000] Amd/Fujitsu Extended Query Table at 0x0040 
 +[    0.400000] ​  ​Amd/​Fujitsu Extended Query version 1.1. 
 +[    0.408000] number of CFI chips: 1 
 +[    0.412000] bcm63xxpart:​ CFE boot tag found with version 6 and board type 96368MVWG 
 +[    0.420000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000 
 +[    0.424000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length 11ff00 
 +[    0.432000] bcm63xxpart:​ Partition 2 is rootfs offset 130000 and length 6c0000 
 +[    0.440000] bcm63xxpart:​ Partition 3 is nvram offset 7f0000 and length 10000 
 +[    0.448000] bcm63xxpart:​ Partition 4 is linux offset 10000 and length 7e0000 
 +[    0.456000] bcm63xxpart:​ Spare partition is offset 330004 and length 4bfffc 
 +[    0.460000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 
 +[    0.468000] Creating 5 MTD partitions on "​physmap-flash.0":​ 
 +[    0.476000] 0x000000000000-0x000000010000 : "​CFE"​ 
 +[    0.480000] 0x000000010100-0x000000130000 : "​kernel"​ 
 +[    0.488000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only 
 +[    0.500000] 0x000000130000-0x0000007f0000 : "​rootfs"​ 
 +[    0.508000] mtd: device 2 (rootfs) set to be root filesystem 
 +[    0.512000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=0x330000,​ len=0x4c0000 
 +[    0.520000] 0x000000330000-0x0000007f0000 : "​rootfs_data"​ 
 +[    0.528000] 0x0000007f0000-0x000000800000 : "​nvram"​ 
 +[    0.536000] 0x000000010000-0x0000007f0000 : "​linux"​ 
 +[    0.544000] bcm63xx-spi bcm63xx-spi:​ at 0xb0000800 (irq 9, FIFOs size 542) 
 +[    0.592000] b53_common: found switch: BCM63xx, rev 0 
 +[    0.596000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec 
 +[    0.608000] TCP: cubic registered 
 +[    0.608000] NET: Registered protocol family 17 
 +[    0.616000] Bridge firewalling registered 
 +[    0.620000] 8021q: 802.1Q VLAN Support v1.8 
 +[    0.632000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. 
 +[    0.640000] Freeing unused kernel memory: 244K (80323000 - 80360000) 
 +procd: Console is alive 
 +procd: - watchdog - 
 +procd: - preinit - 
 +ifconfig: SIOCGIFFLAGS:​ No such device 
 +Press the [f] key and hit [enter] to enter failsafe mode 
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level 
 +[    4.428000] Button Hotplug driver version 0.4.1 
 +mount_root: jffs2 is not ready - EOF marker found 
 +ifconfig: SIOCGIFFLAGS:​ No such device 
 +procd: - early - 
 +procd: - watchdog - 
 +procd: - ubus - 
 +procd: - init - 
 +Please press Enter to activate this console. 
 +[    8.292000] NET: Registered protocol family 10 
 +[    8.316000] nf_conntrack version 0.5.0 (453 buckets, 1812 max) 
 +[    8.332000] ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +[    8.356000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093 
 +[    8.364000] Backport generated by backports.git backports-20130802-0-gdb67a3f 
 +[    8.376000] ip_tables: (C) 2000-2006 Netfilter Core Team 
 +[    8.436000] xt_time: kernel timezone is -0000 
 +[    8.468000] cfg80211: Calling CRDA to update world regulatory domain 
 +[    8.488000] cfg80211: World regulatory domain updated: 
 +[    8.492000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp) 
 +[    8.500000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) 
 +[    8.508000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) 
 +[    8.516000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) 
 +[    8.524000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) 
 +[    8.532000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) 
 +[    8.540000] cfg80211: ​  ​(57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) 
 +[    8.652000] PPP generic driver version 2.4.2 
 +[    8.660000] NET: Registered protocol family 24 
 +[    8.704000] b43-phy0: Broadcom 43222 WLAN found (core revision 16) 
 +[    8.756000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 
 +[    8.788000] Broadcom 43xx driver loaded [ Features: PNL ] 
 +[   ​16.752000] jffs2_scan_eraseblock():​ End of filesystem marker found at 0x0 
 +[   ​16.772000] jffs2_build_filesystem():​ unlocking the mtd device... done. 
 +[   ​16.776000] jffs2_build_filesystem():​ erasing all blocks after the end marker... [   ​17.472000] device eth0.1 entered promiscuous mode 
 +[   ​17.476000] device eth0 entered promiscuous mode 
 +[   ​17.488000] br-lan: port 1(eth0.1) entered forwarding state 
 +[   ​17.492000] br-lan: port 1(eth0.1) entered forwarding state 
 +[   ​18.460000] IPv6: ADDRCONF(NETDEV_CHANGE):​ eth0.1: link becomes ready 
 +[   ​19.496000] br-lan: port 1(eth0.1) entered forwarding state 
 +done. 
 +[   ​58.092000] jffs2: notice: (547) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. 
 +procd: - init complete - 
 + 
 + 
 + 
 +BusyBox v1.19.4 (2013-12-03 08:14:57 CET) built-in shell (ash) 
 +Enter '​help'​ for a list of built-in commands. 
 + 
 +  _______ ​                    ​________ ​       __ 
 + ​| ​      ​|.-----.-----.-----.| ​ |  |  |.----.| ​ |_ 
 + ​| ​  ​- ​  ​|| ​ _  |  -__|     ​|| ​ |  |  ||   ​_|| ​  _| 
 + ​|_______|| ​  ​__|_____|__|__||________||__| ​ |____| 
 +          |__| W I R E L E S S   F R E E D O M 
 + ​-----------------------------ujjjjjjjj 
 +                                        BARRIER BREAKER (Bleeding Edge, r38990) 
 + ​----------------------------------------------------- 
 +  * 1/2 oz Galliano ​        Pour all ingredients into 
 +  * 4 oz cold Coffee ​       an irish coffee mug filled 
 +  * 1 1/2 oz Dark Rum       with crushed ice. Stir. 
 +  * 2 tsp. Creme de Cacao 
 + ​----------------------------------------------------- 
 +root@OpenWrt:/#​ 
 +</​code>​ 
 + 
 +Openwrt debug level 4 pastebin:  
 +http://​pastebin.com/​KCBeMZif
  
  
Line 34: Line 915:
 For some Help with the Tags, please have a look here: [[meta/​tags]] For some Help with the Tags, please have a look here: [[meta/​tags]]
  
-{{tag>​bcm63xx bcm6368 FastEthernet 4Port 2PHY 2Ant DetachableAntenna InternalAntenna 32RAM 8Flash xDSL ADSL2+ VDSL1 VDSL2 MIPS MIPS32 802.11bgn}}+{{tag>​bcm63xx bcm6368 FastEthernet 4Port 2nic 2Ant DetachableAntenna InternalAntenna 32RAM 8Flash xDSL ADSL2+ VDSL1 VDSL2 MIPS MIPS32 802.11bgn ​trng}}
toh/zyxel/p-870hn-51b.1351547740.txt.bz2 · Last modified: 2012/10/29 22:55 (external edit)