Zyxel NBG6716

Also known as ZyXEL Media Router AC 1750 Ultimate Performance. The hardware is very similar to the TP-Link TL-WDR7500, but with a large NAND flash, internal antennas, and an upright design. The factory firmware is based on OpenWrt (Attitude Adjustment?), customized by Zyxel & Qualcomm, and includes StreamBoost (fq_codel-based QOS).

Supported Versions

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Notes
v1 2013 - Barrier Breaker (14.07) V-1.00 silkscreened on the main board

Hardware Highlights

CPU Ram Flash Network Gigabit USB Serial JTag
QCA9558@720MHz 256MiB 16MiB + 256MiB 4x1 Yes 2*USB 2.0 Yes ?

Manufacturer's site: http://www.zyxel.com/products_services/nbg6716.shtml?t=p

Installation

There exist 2 variants:

Upgrade from ZyXEL customized OpenWRT r2343

Download the openwrt image to the device, openwrt-ar71xx-nand-nbg6716-squashfs-factory.bin is needed. On the router console, type:

 # mtd -r write openwrt-ar71xx-nand-nbg6716-squashfs-factory.bin /dev/mtd7
The device then reboots and awaits your login.

Sysupgrade

sysupgrade is supported with the new nand method. Please use openwrt-ar71xx-nand-nbg6716-squashfs-sysupgrade.tar for this.

Recovery

The device is able to flash from a tftp server. You have to fullfill following requirements:

  • Configure your server to 192.168.1.33, netmask 255.255.255.0
  • Copy your firmware file into the tftp directory and name it ras.bin (IE download it from zyxel directly)
  • Boot up your device holding the WPS (Key) button.

After the image has been flashed all LEDs will blink. It takes about 10seconds.

WiFi

Currently WiFi has some issues. You have to set a MAC address to the single VAPs. If you dont set a MAC, you risk firmware reboots. Example:

 config wifi-iface 
 	option device 'radio0'
 	option mode 'ap'
 	option encryption 'none'
 	option ssid 'TEST'
 	option network 'LAN'
 	option macaddr 'e8:f5:28:43:69:81'
You can generate one or use the documented one on the backside. You can also look at eth1
 # ifconfig eth0
 eth0      Link encap:Ethernet  HWaddr F4:F5:28:73:49:16  
 ...
and subtract 1 from the last filed. ⇒ F4:F5:28:73:49:15

Developement sources

Sources are integrated into trunk since R40502 (2014-04-13).

Sysupgrade is currently not integrated because image format will change. This is the intermediate http://www.ddimension.net/patches/sysupgrade.patch patch.

Recovery

The device is able to flash from a tftp server. You have to fullfill following requirements:

  • Configure your server to 192.168.1.33, netmask 255.255.255.0
  • Copy your firmware file into the tftp directory and name it ras.bin (IE download it from zyxel directly)
  • Boot up your device holding the WPS (Key) button.

After the image has been flashed all LEDs will blink. It takes about 10seconds.

Hardware

info

Architecture: MIPS32 (MIPS74Kc)
Target: ar7xxx/ar9xxx
Vendor: ZyXEL
Bootloader: U-Boot
System-On-Chip: QCA9558-AT4A Rev 2
CPU Model: QCA9558
CPU Speed: 720Mhz
Flash size: 16MB + 256MB
Flash Chip No1: Macronix MX25L128 (16MB)
Flash Chip No2: Hynix H27U2G8F2CTR-BC (256MB)
RAM size: 256MB
RAM Chip: Nanya NT5TU64M16GG-AC x 2
Switch: QCA8337
WAN: 1x RJ45 Gbe
Ethernet: 4x RJ45 Gbe
Wireless No1: SoC-integrated QCA9558-AT4A w/ 3x3 MIMO for 2.4GHz 802.11b/g/n
Wireless No2: QCA9880-2R4E w/ 3x3 MIMO for 5GHz 802.11a/n/ac
USB: Yes 2 x 2.0
Serial: Yes (see picture below)
JTAG: unknown
Buttons: power switch, on/off switch, wifi switch, 2 x USB eject button
Power: external 12V 2A

Photos

zyxel_nbg6716_serial.jpg

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

The device uses TTL @ 3.3V and not a standard RS-232 Serial that operates between 3 and 15V, so do not try to connect it to a common serial adapter: you will certainly fry the serial circuit or even the whole board. There are plenty of USB to TTL and RS-232 to TTL available on the market, just be careful with the voltage: the standard is 5V and it may also damage your board. Look for the ones with 3.3V or with both voltages and a way to switch between them.

Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None

J1

PIN1: 3.3V
PIN2: GND
PIN3: RX
PIN4: TX

PINS 
----> Power On/Off / Wifi On/Off button side
4 3 2 1
<--- USB ports side

Bootlogs

OEM bootlog

U-Boot 2009.11 (Aug 07 2013 - 10:23:41) NBG6716 - Scorpion 1.0 DRAM: 32bit ddr2 256 MB Flash: 16 MB *** Warning *** : PCIe WLAN Module not found !!! Net: eth0, eth1 NAND: Hynix NAND 256MiB 3,3V 8-bit [256MB] ZyXEL zloader v1.01 (Aug 07 2013 - 10:45:52) Multiboot clinent version: 1.1 could not establish link on eth0 eth_init failed! ### JFFS2 loading '/boot/vmlinux.lzma.uImage' to 0x80400000 Scanning JFFS2 FS: '/boot/vmlinux.lzma.uImage' found, done Loading file: done ### JFFS2 load complete: 1017958 bytes loaded to 0x80400000 ## Booting kernel from Legacy Image at 80400000 ... Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2013-11-22 1:16:47 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1017894 Bytes = 994 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Linux version 3.3.8 (benny@U1004en) (gcc version 4.6.4 20121106 (prerelease) (Linaro GCC 4.6-2012.11) ) #1 Fri Nov 22 09:16:38 CST 2013 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019750 (MIPS 74Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9558 rev 0 [ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00010000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00010000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: board=NBG6716 root=/dev/mtdblock7 rootfstype=jffs2 noinitrd zld_ver=1.01 console=ttyS0,115200 mtdparts=spi0.0:0x40000(u-boot)ro,0x10000(env)ro,0x10000(RFdata)ro,-(nbu);ath79-nand:0x200000(rootfs_data),0x200000(romd),0x100000(header),0x1E00000(rootfs),0x100000(header1),0x1E00000(rootfs1),0x200000(bu1),-(bu2) mem=256M ethaddr=FC:F5:28:D3:28:B4 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 256324k/262144k available (2181k kernel code, 5820k reserved, 575k data, 176k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:83 [ 0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] Initialized recycle list for cpu 0. [ 0.070000] NET: Registered protocol family 16 [ 0.080000] gpiochip_add: registered GPIOs 0 to 23 on device: ath79 [ 0.080000] MIPS: machine is ZyXEL NBG6716 [ 0.090000] ar724x-pci ar724x-pci.0: PCIe link is down [ 0.090000] registering PCI controller with io_map_base unset [ 0.100000] registering PCI controller with io_map_base unset [ 0.510000] bio: create slab at 0 [ 0.510000] PCI host bridge to bus 0000:00 [ 0.520000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.520000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.530000] PCI host bridge to bus 0000:01 [ 0.530000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff] [ 0.540000] pci_bus 0000:01: root bus resource [io 0x0001] [ 0.540000] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 0.550000] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref] [ 0.550000] pci 0000:01:00.0: using irq 41 for pin 1 [ 0.560000] Switching to clocksource MIPS [ 0.560000] NET: Registered protocol family 2 [ 0.570000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.570000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.580000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.580000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.590000] TCP reno registered [ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.600000] NET: Registered protocol family 1 [ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.620000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.630000] msgmni has been set to 500 [ 0.640000] io scheduler noop registered [ 0.640000] io scheduler deadline registered (default) [ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.680000] console [ttyS0] enabled, bootconsole disabled [ 0.680000] console [ttyS0] enabled, bootconsole disabled [ 0.690000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.700000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.700000] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.710000] Creating 4 MTD partitions on "spi0.0": [ 0.720000] 0x000000000000-0x000000040000 : "u-boot" [ 0.720000] 0x000000040000-0x000000050000 : "env" [ 0.730000] 0x000000050000-0x000000060000 : "RFdata" [ 0.730000] 0x000000060000-0x000001000000 : "nbu" [ 0.740000] ath79-nand ath79-nand: AR71xx/AR9xxx Qualcomm-Atheros NAND FLash Controller driver, Version 1.0 (c) 2010 Atheros Communications, Ltd. [ 0.750000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) [ 0.760000] Bad block table found at page 131008, version 0x01 [ 0.770000] Bad block table found at page 130944, version 0x01 [ 0.780000] 8 cmdlinepart partitions found on MTD device ath79-nand [ 0.780000] Creating 8 MTD partitions on "ath79-nand": [ 0.790000] 0x000000000000-0x000000200000 : "rootfs_data" [ 0.790000] 0x000000200000-0x000000400000 : "romd" [ 0.800000] 0x000000400000-0x000000500000 : "header" [ 0.810000] 0x000000500000-0x000002300000 : "rootfs" [ 0.810000] mtd: partition "rootfs" set to be root filesystem [ 0.820000] split_squashfs: no squashfs found in "ath79-nand" [ 0.820000] 0x000002300000-0x000002400000 : "header1" [ 0.830000] 0x000002400000-0x000004200000 : "rootfs1" [ 0.840000] 0x000004200000-0x000004400000 : "bu1" [ 0.840000] 0x000004400000-0x000010000000 : "bu2" [ 0.850000] ath79-nand ath79-nand: ====== NAND Parameters ====== [ 0.850000] total size = 0x10000000, page = 0x800 block = 0x20000 oob = 0x40 [ 1.000000] ag71xx_mdio: probed [ 1.010000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 1.590000] eth0: Atheros AR8337 switch driver attached. [ 2.780000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316] [ 2.790000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII [ 3.350000] TCP cubic registered [ 3.350000] NET: Registered protocol family 17 [ 3.350000] 8021q: 802.1Q VLAN Support v1.8 [ 3.360000] ### of_selftest(): No testcase data in device tree; not running tests [ 5.930000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 5.950000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:7. [ 5.950000] Freeing unused kernel memory: 176k freed - preinit - Press the [f] key and hit [enter] to enter failsafe mode [ 8.810000] eth0: link up (1000Mbps/Full duplex) - regular preinit - [ 11.080000] JFFS2 notice: (531) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 18 of xref (0 dead, 2 orphan) found. [ 11.280000] SCSI subsystem initialized [ 11.340000] usbcore: registered new interface driver usbfs [ 11.350000] usbcore: registered new interface driver hub [ 11.360000] usbcore: registered new device driver usb [ 11.550000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.560000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller [ 11.570000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 11.610000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 11.630000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 11.630000] hub 1-0:1.0: USB hub found [ 11.640000] hub 1-0:1.0: 1 port detected [ 11.640000] ehci-platform ehci-platform.1: Generic Platform EHCI Controller [ 11.650000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 11.690000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 11.710000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00 [ 11.710000] hub 2-0:1.0: USB hub found [ 11.720000] hub 2-0:1.0: 1 port detected [ 11.730000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 11.760000] uhci_hcd: USB Universal Host Controller Interface driver [ 11.790000] Initializing USB Mass Storage driver... [ 11.790000] usbcore: registered new interface driver usb-storage [ 11.800000] USB Mass Storage support registered. [ 13.000000] JFFS2 notice: (532) check_node_data: wrong data CRC in data node at 0x00102794: read 0xa1696320, calculated 0x46204b31. switching to jffs2 - init - [ 31.960000] eth0: link down Please press Enter to activate this console. sysinit: Start preboot sysinit: Start defconfig sysinit: Start luci_fixtime sysinit: Fri Aug 9 04:23:00 UTC 2013 sysinit: Start ess_info sysinit: Start boot sysinit: Start password sysinit: Changing password for root sysinit: New password: sysinit: Retype password: sysinit: Password for root changed by root sysinit: Start procd sysinit: Start fstab sysinit: Start network sysinit: Interface wan not found sysinit: Start wan_down sysinit: Start usb sysinit: Start wireless sysinit: phy for wifi device wifi1 not found sysinit: Start firewall sysinit: Start cron sysinit: Start dropbear sysinit: Start nat sysinit: Start proftpd sysinit: Changing password for root sysinit: New password: sysinit: Retype password: sysinit: Password for root changed by root sysinit: Start telnet sysinit: Start uhttpd sysinit: disable www sysinit: Start updatedd sysinit: Start luci_dhcp_migrate sysinit: Start dnsmasq sysinit: no more available dns servers ! sysinit: no more available dns servers ! sysinit: Start samba sysinit: Changing password for root sysinit: New password: sysinit: Retype password: sysinit: Password for root changed by root sysinit: Start wol sysinit: Start wan_up sysinit: Start route sysinit: Start done sysinit: Start miniupnpd sysinit: miniupnpd starting ... sysinit: Start led sysinit: Start portTrigger sysinit: Start time_daemon sysinit: Start uci2streamboost sysinit: Start watchdog sysinit: Start webstr_filter sysinit: Start wifi_scheduling sysinit: Start wifi_scheduling5G sysinit: Start wireless5G_macfilter sysinit: Start wireless_macfilter sysinit: Start streamboost sysinit: [ OK ] 10_p0f boot sysinit: [ OK ] 20_dbldae boot sysinit: [ OK ] 30_bwcd boot sysinit: [ OK ] 35_leash boot sysinit: [ OK ] 40_policy_engine boot sysinit: [ OK ] 50_drflocs boot sysinit: [ OK ] 55_flowcap boot sysinit: [ OK ] 60_ozker boot sysinit: [ OK ] 80_aperture boot sysinit: Start sysntpd sysinit: Start dlna sysinit: Start igmpproxy sysinit: Start sysctl sysinit: Start wan_status_monitor sysinit: Start zybootend sysinit: phy for wifi device wifi0 not found sysinit: phy for wifi device wifi1 not found sysinit: Boot finished! NBG6716 login: root Password: BusyBox v1.19.4 (2013-11-22 08:50:37 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- (r2211) root@NBG6716:~

OpenWRT Boot Log

### JFFS2 loading '/boot/vmlinux.lzma.uImage' to 0x80400000 Scanning JFFS2 FS: '/boot/vmlinux.lzma.uImage' found, done Loading file: done ### JFFS2 load complete: 985978 bytes loaded to 0x80400000 ## Booting kernel from Legacy Image at 80400000 ... Image Name: MIPS OpenWrt Linux-3.10.32 Created: 2014-03-26 10:26:21 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 985914 Bytes = 962.8 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Linux version 3.10.32 (avalentin@varus) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r39957) ) #26 Wed Mar 26 11:26:16 CET 2014 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019750 (MIPS 74Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9558 rev 0 [ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x0fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x0fffffff] [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: board=NBG6716 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(env)ro,64k(RFdata)ro,-(nbu);ar934x-nfc:2048k(zyxel_rfsd),2048k(romd),1024k(header),2048k(kernel),-(ubiroot) ubi.mtd=ubiroot mem=256M rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 256320k/262144k available (2310k kernel code, 5824k reserved, 430k data, 200k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] NET: Registered protocol family 16 [ 0.070000] MIPS: machine is Zyxel NBG6716 [ 0.530000] ar724x-pci ar724x-pci.0: PCIe link is down [ 0.530000] registering PCI controller with io_map_base unset [ 0.540000] registering PCI controller with io_map_base unset [ 0.550000] bio: create slab at 0 [ 0.550000] PCI host bridge to bus 0000:00 [ 0.560000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.570000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.570000] PCI host bridge to bus 0000:01 [ 0.580000] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff] [ 0.580000] pci_bus 0000:01: root bus resource [io 0x0001] [ 0.590000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.590000] pci 0000:01:00.0: invalid calibration data [ 0.600000] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 0.600000] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref] [ 0.610000] pci 0000:01:00.0: using irq 41 for pin 1 [ 0.610000] Switching to clocksource MIPS [ 0.620000] NET: Registered protocol family 2 [ 0.620000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.620000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.620000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.630000] TCP: reno registered [ 0.630000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.650000] NET: Registered protocol family 1 [ 0.660000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.670000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.680000] msgmni has been set to 500 [ 0.680000] io scheduler noop registered [ 0.680000] io scheduler deadline registered (default) [ 0.690000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.720000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.720000] console [ttyS0] enabled, bootconsole disabled [ 0.720000] console [ttyS0] enabled, bootconsole disabled [ 0.740000] ath79-spi ath79-spi: master is unqueued, this is deprecated [ 0.740000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.750000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.750000] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.760000] Creating 4 MTD partitions on "spi0.0": [ 0.760000] 0x000000000000-0x000000040000 : "u-boot" [ 0.770000] 0x000000040000-0x000000050000 : "env" [ 0.780000] 0x000000050000-0x000000060000 : "RFdata" [ 0.780000] 0x000000060000-0x000001000000 : "nbu" [ 0.790000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64 [ 0.800000] Scanning device for bad blocks [ 0.980000] 5 cmdlinepart partitions found on MTD device ar934x-nfc [ 0.980000] Creating 5 MTD partitions on "ar934x-nfc": [ 0.990000] 0x000000000000-0x000000200000 : "zyxel_rfsd" [ 1.000000] 0x000000200000-0x000000400000 : "romd" [ 1.000000] 0x000000400000-0x000000500000 : "header" [ 1.010000] 0x000000500000-0x000000700000 : "kernel" [ 1.010000] 0x000000700000-0x000010000000 : "ubiroot" [ 1.050000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0 [ 2.280000] libphy: ag71xx_mdio: probed [ 2.830000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316] [ 2.840000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 3.400000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII [ 3.400000] TCP: cubic registered [ 3.410000] NET: Registered protocol family 17 [ 3.410000] 8021q: 802.1Q VLAN Support v1.8 [ 3.420000] UBI: attaching mtd8 to ubi0 [ 7.190000] UBI: scanning is finished [ 7.220000] UBI: attached mtd8 (name "ubiroot", size 249 MiB) to ubi0 [ 7.220000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.230000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.240000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.240000] UBI: good PEBs: 1992, bad PEBs: 0, corrupted PEBs: 0 [ 7.250000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 7.260000] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 127993961 [ 7.270000] UBI: available PEBs: 791, total reserved PEBs: 1201, PEBs reserved for bad PEB handling: 40 [ 7.280000] UBI: background thread "ubi_bgt0d" started, PID 266 [ 7.280000] mtd: device 9 (rootfs) set to be root filesystem [ 7.300000] VFS: Mounted root (squashfs filesystem) readonly on device 31:9. [ 7.300000] Freeing unused kernel memory: 200K (8030e000 - 80340000) procd: Console is alive procd: - watchdog - procd: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.380000] usbcore: registered new interface driver usbfs [ 10.380000] usbcore: registered new interface driver hub [ 10.390000] usbcore: registered new device driver usb [ 10.400000] Button Hotplug driver version 0.4.1 [ 10.410000] SCSI subsystem initialized [ 10.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.420000] ehci-platform: EHCI generic platform driver [ 10.430000] ehci-platform ehci-platform.0: EHCI Host Controller [ 10.440000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 10.450000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled [ 10.450000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 10.480000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 10.480000] hub 1-0:1.0: USB hub found [ 10.490000] hub 1-0:1.0: 1 port detected [ 10.490000] ehci-platform ehci-platform.1: EHCI Host Controller [ 10.500000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 10.510000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled [ 10.510000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 10.540000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00 [ 10.540000] hub 2-0:1.0: USB hub found [ 10.550000] hub 2-0:1.0: 1 port detected [ 10.550000] ehci-pci: EHCI PCI platform driver [ 10.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 10.570000] usbcore: registered new interface driver usb-storage [ 10.580000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 10.830000] eth0: link up (1000Mbps/Full duplex) No jffs2 marker [ 12.410000] jffs2: write-buffering enabled buffer (2048) erasesize (126976) was found [ 12.520000] jffs2: notice: (371) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 166 of xref (0 dead, 142 orphan) found. switching to jffs2 [ 12.560000] eth0: link down procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Failed to connect to ubus Please press Enter to activate this console. Failed to connect to ubus [ 17.910000] NET: Registered protocol family 10 [ 17.920000] NET: Registered protocol family 8 [ 17.920000] NET: Registered protocol family 20 [ 17.940000] Initializing XFRM netlink socket [ 17.940000] NET: Registered protocol family 15 [ 17.950000] Modular ISDN core version 1.1.29 [ 17.960000] NET: Registered protocol family 34 [ 17.970000] DSP module 2.0 [ 17.970000] mISDN_dsp: DSP clocks every 80 samples. This equals 1 jiffies. [ 18.000000] mISDN: Layer-1-over-IP driver Rev. 2.00 [ 18.020000] 0 virtual devices registered [ 18.020000] tun: Universal TUN/TAP device driver, 1.6 [ 18.030000] tun: (C) 1999-2004 Max Krasnyansky [ 18.050000] ipip: IPv4 over IPv4 tunneling driver [ 18.080000] l2tp_core: L2TP core driver, V2.0 [ 18.100000] l2tp_netlink: L2TP netlink interface [ 18.100000] sit: IPv6 over IPv4 tunneling driver [ 18.120000] IPv4 over IPSec tunneling driver [ 18.140000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 18.140000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 18.160000] gre: GRE over IPv4 demultiplexor driver [ 18.170000] ip_gre: GRE over IPv4 tunneling driver [ 18.200000] ip6_gre: GRE over IPv6 tunneling driver [ 18.210000] PPP generic driver version 2.4.2 [ 18.230000] nf_conntrack version 0.5.0 (4008 buckets, 16032 max) [ 18.240000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 18.300000] Netfilter messages via NETLINK v0.30. [ 18.310000] ip_set: protocol 6 [ 18.360000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d [ 18.370000] Backport generated by backports.git backports-20140124-0-g1256d3e [ 18.430000] cfg80211: Calling CRDA to update world regulatory domain [ 18.430000] cfg80211: World regulatory domain updated: [ 18.440000] cfg80211: DFS Master region: unset [ 18.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 18.450000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 18.460000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 18.470000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 18.470000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 18.480000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 18.490000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 18.550000] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 18.560000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 18.620000] ath10k: pci irq legacy [ 20.010000] ath10k: qca988x hw2.0 (0x4100016c) fw 10.1.467.2-1 api 2 htt 2.1 [ 20.110000] cfg80211: Calling CRDA for country: US [ 20.120000] cfg80211: Regulatory domain changed to country: US [ 20.120000] cfg80211: DFS Master region: FCC [ 20.130000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.140000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 20.140000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm) [ 20.150000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm) [ 20.160000] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm) [ 20.170000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm) [ 20.170000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm) [ 20.180000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 20.210000] Linux video capture interface: v2.00 [ 20.230000] u32 classifier [ 20.230000] input device check on [ 20.240000] Actions configured [ 20.250000] Mirror/redirect action on [ 20.270000] Failed to load ipt action [ 20.280000] netem: version 1.3 [ 20.320000] arp_tables: (C) 2002 David S. Miller [ 20.390000] usbcore: registered new interface driver cdc_acm [ 20.390000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 20.420000] usbcore: registered new interface driver cdc_wdm [ 20.420000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 20.440000] gspca_main: v2.14.0 registered [ 20.460000] usbcore: registered new interface driver sonixb [ 20.460000] usbcore: registered new interface driver sonixj [ 20.470000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 20.510000] ctnetlink v0.93: registering with nfnetlink. [ 20.530000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 20.540000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 20.550000] PPP MPPE Compression module registered [ 20.560000] NET: Registered protocol family 24 [ 20.570000] usbcore: registered new interface driver usblp [ 20.590000] usbcore: registered new interface driver usbserial [ 20.600000] usbcore: registered new interface driver usbserial_generic [ 20.610000] usbserial: USB Serial support registered for generic [ 20.660000] xt_time: kernel timezone is -0000 [ 20.670000] usbcore: registered new interface driver cdc_ether [ 20.680000] usbcore: registered new interface driver cdc_ncm [ 20.690000] usbcore: registered new interface driver ftdi_sio [ 20.700000] usbserial: USB Serial support registered for FTDI USB Serial Device [ 20.710000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 20.720000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 20.740000] usbcore: registered new interface driver pl2303 [ 20.750000] usbserial: USB Serial support registered for pl2303 [ 20.760000] usbcore: registered new interface driver qmi_wwan [ 20.770000] usbcore: registered new interface driver rndis_host [ 20.780000] usbcore: registered new interface driver sierra [ 20.780000] usbserial: USB Serial support registered for Sierra USB modem [ 20.790000] usbcore: registered new interface driver sierra_net [ 20.850000] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47 [ 20.860000] usbcore: registered new interface driver cdc_mbim [ 20.880000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 20.900000] usbcore: registered new interface driver option [ 20.910000] usbserial: USB Serial support registered for GSM modem (1-port) [ 20.930000] usbcore: registered new interface driver qcserial [ 20.950000] usbserial: USB Serial support registered for Qualcomm USB modem [ 20.950000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 31.710000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 31.710000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 31.730000] device eth0.1 entered promiscuous mode [ 31.730000] device eth0 entered promiscuous mode [ 31.760000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 31.760000] eth1: link up (1000Mbps/Full duplex) procd: - init complete - [ 33.180000] eth0: link up (1000Mbps/Full duplex) [ 33.200000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 33.200000] br-lan: port 1(eth0.1) entered forwarding state [ 33.210000] br-lan: port 1(eth0.1) entered forwarding state [ 33.210000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 33.230000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 35.210000] br-lan: port 1(eth0.1) entered forwarding state

Tags

Back to top

toh/zyxel/zyxel_nbg6716.txt · Last modified: 2014/10/15 04:41 by mandrawes