User Tools

Site Tools


toh:actiontec:c1000a

Actiontec C1000A

Common router supplied with CenturyLink (Qwest) ISP subscriptions.

OEM source code available from Actiontec Support - http://opensource.actiontec.com/c1000x.html

Hardware Highlights

SoC Ram Flash Network USB Serial JTag
Broadcom 63168 64 MiB 64 MiB 4 Yes Yes ?

Forum: https://forum.openwrt.org/viewtopic.php?id=51792

Flash Layout

Hardware

Info

Instruction set: MIPS
Vendor: Broadcom
Bootloader: CFE
Board ID: C1000B
System-On-Chip: Broadcom BCM63168
CPU @Frq Dual core BMIPS4350 v8.0 @ 400 MHz
Flash size: 64 MiB
Flash Chip: NAND512W3A2CN6
RAM size: 64 MiB
RAM Chip: DDR2
Wireless 802.11b/g/n integrated (SoC)
Switch: Broadcom BCM53125 / 4x Gigabit ethernet
Modem: aDSL2/vDSL2
USB: Yes 1 x 2.0
Serial: Yes
JTAG: Likely

Photos

Front:
front

Back:
back

Board:
top bottom

Serial

Baud 115200 Data Bits 8 Stop Bits 1 No Parity No Flow Control

Bootlogs

OEM bootlog

CFE version 1.0.38-114.170 for BCM963268 (32bit,SP,BE) Build Date: Tue Nov 25 12:26:31 PST 2014 (yirun@yirun-desktop) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name ST NAND512W3A2CN6, id 0x2076 block 16KB size 65536KB External switch id = 53125 Chip ID: BCM63168C0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.0.21:ffffff00 Host IP address : 192.168.0.100 Gateway IP address : 192.168.0.1 Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 5 Boot image (0=latest, 1=previous) : 0 Board Id (0-28) : C1000B Number of MAC Addresses (1-32) : 16 Base MAC Address : 20:76:00:59:b0:10 PSI Size (1-64) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Board Serial Number : CVPA2212503450 Factory FW Version : CAC001-31.30L.8 WPS PIN : 33771571 WPA KEY : 9cth2kpuds95eu Admin Password : h7Vg7xb7 This is one CFE built for CENTURYLINK C1000A *** Press any key to stop auto run (5 seconds) *** Auto run second count down: 0 Booting from latest image (0xb8004000) ... image check : verified the image blocks 1 to 1306 Decompression OK! Entry at 0x80333eb0 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80333eb0 Linux version 2.6.30 (yirun@yirun-desktop) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Tue Nov 25 12:30:32 PST 2014 BCM Flash API. Flash device is not found. C1000B prom init DSL SDRAM reserved: 0x180000 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003e80 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003e80 On node 0 totalpages: 16000 free_area_init_node: node 0, pgdat 8040c120, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 93 pages used for memmap Normal zone: 11811 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15875 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes PID hash table entries: 256 (order: 8, 1024 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Calibrating delay loop... Mount-cache hash table entries: 512 Broadcom Logger v0.1 Nov 25 2014 12:27:00 Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Total Flash size: 0K with -1 sectors Internal 1P2 VREG will be shutdown if unused...Used, leave it on (00008bb1-0000861b=1430>=300) registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Nov 25 2014 12:30:20 initialized Broadcom GBPM v0.1 Nov 25 2014 12:30:21 initialized PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods bcm963xx_mtd driver v2.0 ##init_brcm_physmap exit -->brcmnand_scan: CS=0, numchips=1, csi=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=04042300, chipSelect=0 brcmnand_read_id: CS0: dev_id=20762076 After: NandSelect=40000001, nandConfig=04042300 Block size=00004000, erase shift=14 timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 220 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=16, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=16, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 300 CS=0, chip->ctrl->CS[0]=0 500 chip=83a38190, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0001ffe0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0001ffc0, version 0x01 for chip on CS0 brcmnand_scan 99 Creating 6 MTD partitions on "brcmnand.0": 0x000000008000-0x000001d80000 : "rootfs" 0x000001d84000-0x000003afc000 : "rootfs_update" 0x000003b00000-0x000003f00000 : "data" 0x000000000000-0x000000004000 : "nvram" 0x000000004000-0x000000008000 : "tag" 0x000001d80000-0x000001d84000 : "tag_update" PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled sesBtn_mapIntr: is_sesBtn_irq_shared=0, sesBtn_irq=1 SES: LED GPIO 0x8012 is enabled PCIe: No device found - Powering down brcm_board_init: isShared=0, rstToDflt_irq=0 Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmPktDma_init: Broadcom Packet DMA Library initialized bcmxtmrt: Broadcom BCM3168C0 ATM/PTM Network Device v0.5 Nov 25 2014 12:30:07 IPSEC SPU: SUCCEEDED GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. init started: BusyBox v1.17.2 (2014-11-25 12:33:24 PST) starting pid 227, tty '': '/etc/init.d/rcS' starting pid 232, tty '': '-/bin/sh' BusyBox v1.17.2 (2014-11-25 12:33:24 PST) built-in shell (ash) Enter 'help' for a list of built-in commands. JFFS2 notice: (230) check_node_data: wrong data CRC in data node at 0x002f28cc: read 0xf4c4ab29, calculated 0xc04acbfe. Loading drivers and kernel modules... bcm96368wdt: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Nov 25 2014 12:28:34 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers=4730, buf size=2128 Broadcom BPM Module Char Driver v0.1 Nov 25 2014 12:27:24 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Nov 25 2014 12:28:35 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Nov 25 2014 12:28:35 chipId 0x631680C0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Nov 25 2014 12:28:29 Registered <241> Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done FAP Debug values at 0xa251e3b0 0xa259e3b0 Allocated FAP0 GSO Buffers (0xA252F438) : 1048576 bytes @ 0xA2600000 Allocated FAP1 GSO Buffers (0xA25AF438) : 1048576 bytes @ 0xA2700000 Allocated FAP0 TM SDRAM Queue Storage (a252f43c) : 341376 bytes @ a2000000 Allocated FAP1 TM SDRAM Queue Storage (a25af43c) : 341376 bytes @ a2080000 [NTC fapProto] fapReset : Reset FAP Protocol layer fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes bcmPktDma_bind: FAP Driver binding successfull [FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3976>, free <2680>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3976>, free <2680>, total<8192> [FAP0] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576> [FAP1] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576> [FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP1] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP0] GSO Buffer set to 0xA2600000 [FAP1] GSO Buffer set to 0xA2700000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. [FAP0] FAP TM: ON [FAP1] FAP TM: ON bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM63168C0 Ethernet Network Device v0.1 Nov 25 2014 12:30:00 Broadcom GMAC Char Driver v0.1 Nov 25 2014 12:30:05 Registered<249> Broadcom GMAC Driver v0.1 Nov 25 2014 12:30:05 Initialized fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000 ETH Init: Ch:0 - 200 tx BDs at 0xb0a20650 fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000 ETH Init: Ch:1 - 200 tx BDs at 0xb0820650 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184 ETH Init: Ch:0 - 600 rx BDs at 0xb0821910 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth3: MAC Address: 20:76:00:59:B0:10 eth2: MAC Address: 20:76:00:59:B0:10 eth1: MAC Address: 20:76:00:59:B0:10 eth0: MAC Address: 20:76:00:59:B0:10 eth4: MAC Address: 20:76:00:59:B0:10 eth5: MAC Address: 20:76:00:59:B0:10 Broadcom BCM3168C0 USB Network Device v0.4a Nov 25 2014 12:28:41 usb0: MAC Address: 20 76 00 59 B0 13 usb0: Host MAC Address: 20 76 00 59 B0 14 hub 1-0:1.0: over-current change on port 2 USBD Initialization done status 0 USB Link DOWN. [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Nov 25 2014 12:27:24 Registered <245> --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=3074 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=512 Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_map.bin srom rev:8 wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16 wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.3.cpeCAC002-31.30L76.0 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered Endpoint: endpoint_init entry Endpoint: endpoint_init board id C1000B Endpoint: endpoint_init board id C1000B is not C2000A, exit. insmod: can't insert '/lib/modules/2.6.30/extra/endpointdd.ko': Operation not permitted p8021ag: p8021ag_init entry -/bin/sh: cmf: not found =====CENTURYLINK Release Version CAC002-31.30L.76/CAH005-31.30L.76 (build timestamp 141125_1231) ===== smd:error:17.435:initDls:431:Get Board ID C1000A rm: can't remove '/var/dbus/messagebus.pid': No such file or directory ssk:error:24.597:lck_checkBeforeEntry:230:lock required during cmsObj_getNextInSubTreeFlags ssk:error:24.620:rutVoice_getMaxPhysEndpt:408:failed to open file /dev/bcmendpoint0 ssk:error:24.641:rutVoice_getNumFxoEndpt:521:failed to open file /dev/bcmendpoint0 ssk:error:24.663:rutVoice_getNumFxsEndpt:464:failed to open file /dev/bcmendpoint0 ssk:error:24.685:rutVoice_getNumFxoEndpt:521:failed to open file /dev/bcmendpoint0 ###Tag1 signature(Actiontec),version(CAC002-31.30L.76),version2(CAH005-31.30L.76),imageSequence(538) ###Tag2 signature(Actiontec),version(CAC002-31.30L.76),version2(CAH005-31.30L.76),imageSequence(537) ssk:error:32.540:ctl_rut_reWriteIPv6Hosts:1059:can not open 'hostsv6'-file Host MIPS Clock divider pwrsaving is enabled ssk:error:32.818:insertModuleByIndex:442:Failed on command . ssk:error:32.819:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() no exist file [/var/autoreservation] error num [2],reason [No such file or directory] Netfilter messages via NETLINK v0.30. ssk:error:35.205:insertModuleByIndex:442:Failed on command . ssk:error:35.206:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() ssk:error:36.466:insertModuleByIndex:442:Failed on command . ssk:error:36.466:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() ssk:error:37.730:insertModuleByIndex:442:Failed on command . ssk:error:37.730:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() ssk:error:38.983:insertModuleByIndex:442:Failed on command . ssk:error:38.984:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() WLmngr Daemon is running optarg=0 shmId=0 killall: wlevt: no process killed wlevt is ready for new msg... ssk:error:39.936:rcl_lanAlgObject:28:switch SIP ALG to state 0 rmmod nf_conntrack_sip and nf_nat_sip rmmod: can't unload 'nf_nat_sip': unknown symbol in module, or unknown parameter rmmod: can't unload 'nf_conntrack_sip': unknown symbol in module, or unknown parameter BcmAdsl_Initialize=0xC02790F8, g_pFnNotifyCallback=0xC02BDEB4 AdslCoreLoadImage: Single line PHY lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA3FFFFF8, 0x80008040 0x10280008 *** XfaceOffset: 0x65790 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xEA510 => 0x1217A0 *** AdslCoreSharedMemInit: shareMemSize=67645(67648) AdslCoreHwReset: pLocSbSta=80c88000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3FA95C4 XdslMediaSearch: current media(0) --> 0x10608700 ***BcmDiagsMgrRegisterClient: 0 *** dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22be0 bytes remaining 584 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22be0 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a23220 bytes remaining 456 XTM Init: Ch:1 - 16 rx BDs at 0xb0a23220 bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system bcmxtmcfg: gulBondDslMonitorValid = 1 iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) ssk:error:41.371:rutEth_setSwitchWanPort:193:ioctl SIOCSWANPORT ewan0 returns error! ifconfig: ioctl 0x8913 failed: No such device nf_conntrack version 0.5.0 (1024 buckets, 8192 max) iptables: No chain/target/match by that name captiveEnable=0,webActiveLogEnable=0,webSiteBlockEnable=0 set NETLINK_RECV_NO_ENOBUFS ssk:error:42.210:rcl_detectWANServiceObject:321:starting detectWANService, pid=1217 ssk:error:42.224:rcl_wanOpt60Object:371:++++++++newObj->WANOption60=CTL ssk:error:42.322:ssk_init:1388:dbus-daemon is ready now. WPS Device PIN = 33771571 < SES_LED_OFF > Setting SSID: "CenturyLink3450" Setting SSID: "CenturyLink3451" Setting SSID: "CenturyLink3452" Setting SSID: "CenturyLink3453" Setting SSID: "wl0_Guest4" wlctl: Unsupported smd:error:44.378:initDls:431:Get Board ID C1000A ssk:error:44.540:initializeVoice:283:----It's C1000A, Disable voice feature. ifconfig: br1: error fetching interface information: Device not found ifconfig: br2: error fetching interface information: Device not found ifconfig: br3: error fetching interface information: Device not found PMD: Module entry! PMD: couldn't get any msg! PMD: couldn't get any msg! Tue Nov 25 12:31:00 UTC 2014 Broadcom Packet Flow Cache learning via BLOG enabled. Note: Loading 6300 MDK (default) driver for 63168 chip Note: Forcing 53115 driver for 53125 Switch MDK: num_switches = 2 Switch MDK: unit = 0; phy_pbmp = 0x18; config_pbmp = 0x58 status=00 Switch MDK link poll thread: uniteth4 (switch port: 11) Link UP -1 mbps half duplex =0; phypbmp=0x18 AutoNeg is disabled and Speed has changed AutoNeg is disableth5 (switch port: 12) Link UP -1 mbps half duplex ed and Speed has changed ssk:error:46.826:aei_dalVoice_CheckInitCodec:12069:getVpLineObjRet=getVpLineObj()=9804 ssk:error:46.827:setVlCLCodecList:12010:getVpLineObjRet=getVpLineObj()=9804 ssk:error:46.827:setVlCLCodecList:12023:getVpLineCodecListObjRet=cmsObj_getNextInSubTree()=0 ssk:error:46.828:aei_dalVoice_SetVaildCodecs:12123:getVpLineObjRet=getVpLineObj()=9804 Switch MDK link poll thread: unit=1; phypbmp=0xf ssk:error:47.124:ssk_main:1219:cannot handle msg type 0x10000802 acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x1001 eth3 (switch port: 0) Link UP 1000 mbps full duplex < SES_LED_OFF > <WPS_STOP> < SES_LED_OFF > <WPS_SUCCESS> < WSC_EVENTS_PROC_SUCC > >>>>> WPS PushButton Status Change <<<<< iptables: No chain/target/match by that name iptables: Bad rule (does a matching rule exist in that chain?) captiveEnable=0,webActiveLogEnable=0,webSiteBlockEnable=0 iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) ERROR wandev.c:701 get InternetGatewayDevice.LogLevel.2.X_AEI_COM_LogLevel error ERROR wandev.c:719 get InternetGatewayDevice.LogLevel.1.X_AEI_COM_LogLevel error ERROR rtd.c:159 fail to recv msg from msg bus! ERROR rtd.c:159 fail to recv msg from msg bus! ERROR accesscfg.c:314 base64 decode fail! rm: can't remove '/tmp/cfg.xml.gz': No such file or directory WARNING tr69_rut_route.c:98 Both PPPConn and IPConn are Disable! WARNING tr69_rut_route.c:98 Both PPPConn and IPConn are Disable! ERROR tr69_func_aei_firewall_rules.c:69 gwifname is null ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ===Actiontec xDSL Router=== Login: admin Password: > echo && /bin/sh BusyBox v1.17.2 (2014-11-25 12:33:24 PST) built-in shell (ash) Enter 'help' for a list of built-in commands. #


OpenWrt bootlog

Insert OpenWrt Bootlog here


Notes

Tags

toh/actiontec/c1000a.txt · Last modified: 2015/12/10 19:28 by tmomas