User Tools

Site Tools


toh:comtrend:vr3026e

Comtrend VR-3026e

One of the default devices previously provided by Telefónica (O2 Czech Republic) as a part of an xDSL self-installation package.

Supported Versions

Hardware Highlights

VersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
v1Broadcom BCM63682x 400864Broadcom BCM43222 (onboard)b/g/n-4-xDSL-

Installation

Flash Layout

Please check out the article Flash.Layout. It contains an example and a couple of explanations.

OEM easy installation

Setup your ethernet card

  • IP: 192.168.1.2
  • Netmask: 255.255.255.0
  • Gateway: 192.168.1.1
  • DNS: optional, can be blank

Start the CFE bootloader in "Update Software" mode

  1. Power off the router
  2. Press reset button
  3. Keep it pressed while powering up (~10 seconds)
  4. Power LED will turn solid red
  5. Acces to http://192.168.1.1 and upload binary file
  6. Wait until router reboots

Upgrading OpenWrt

generic.sysupgrade

If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

LuCI Web Upgrade Process

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
vlan0 (eth0.0) LAN ports (1 to 4) None
vlan1 (eth0.1) WAN port DHCP
wl0 WiFi Disabled

Switch Ports (for VLANs)

Port Switch port Mode
LAN 1 0 lan
LAN 2 1 lan
LAN 3 2 lan
LAN 4 3 lan

Failsafe mode

Hardware

Info

General
Brand Comtrend
Model VR-3026e
Versions v1
Device Type WiFi Router
Availability Discontinued 2013
Comments - general
OpenWrt Support
Supported Since Revision https://dev.openwrt.org/changeset/46752/
Supported Since Release
Supported Current Release
Unsupported
Hardware
Instruction set MIPS32
Sub Instruction Set
Bootloader CFE
Target brcm63xx
System-On-Chip Broadcom BCM6368
CPU MHz 2x 400
Flash MB 8
RAM MB 64
Network
Ethernet 100M ports 4
Ethernet Gbit ports -
Switch
Modem xDSL
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz -
WLAN Hardware
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports -
SATA ports -
Serial Yes
JTAG Yes
Comments - USB & SATA ports
Misc
LED count
Button count 3
Power supply
Links
Forum Topic URL
WikiDevi URL http://¿
OEM device homepage URL http://¿
Firmware OEM Stock URL http://www.o2.cz/_pub/b4/15/75/236868_957667__657004_298_VR_3028e_CFE_A641_406TO2_C04_R01_.bin
Firmware OpenWrt Install URL http://¿
Firmware OpenWrt Upgrade URL http://¿
Edit the underlying data View/Edit data

Photos

Model Number

Front:
Photo of front of the casing

Back:
Photo of back of the casing

Opening the case

Note: This will void your warranty!

  • To remove the cover do a/b/c

Main PCB:
Photo of PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
vr3025u_board_serial.jpg

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings

GPIO

LEDs

Read: System configuration: Leds to configure the leds

Pin Event Active
2 dsl (green) Low
5 inet (green) High
22 power (green) High
24 power (red) High
31 inet (red) High
497 wps (green) Low

Buttons

hardware.button on howto use and configure the hardware button(s).

Pin Event Active
34 Reset Low
506 WLAN Switch Low
509 WPS Low

Debricking

Hardware mods

Currently none.

Bootlogs

OEM bootlog

CFE version 1.0.37-106.24-31 for BCM96368 (32bit,SP,BE) Build Date: 2012-06-29 16:09:03 (lain@SW1-BCM-04) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB Total Flash size: 8192K with 135 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-15) : 96368MT-1341N1 Number of MAC Addresses (1-32) : 32 Base MAC Address : 38:72:c0:58:32:50 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Serial Number : 129QJA14892 Default PSK key : 6CvVFfbWir *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80014230 Decompression OK! Entry at 0x80014230 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80014230 Linux version 2.6.30 (jim@SW1-BCM-04) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed May 21 15:36:45 CST 2014 Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB 96368MT-1341N1 prom init CPU revision is: 0002a031 (Broadcom4350) Determined physical RAM map: memory: 03ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003ece On node 0 totalpages: 16078 free_area_init_node: node 0, pgdat 8038a7e0, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11888 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes RCU-based detection of stalled CPUs is enabled. NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 59724k/64312k available (2857k kernel code, 4568k reserved, 712k data, 128k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 net_namespace: 1096 bytes NET: Registered protocol family 16 Total Flash size: 8192K with 135 sectors registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff] pci 0000:00:09.0: reg 10 32bit mmio: [0x10001600-0x100016ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10001500-0x100015ff] BLOG v3.0 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 116 io scheduler noop registered (default) Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8010100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8017 is enabled Invalid External Interrupt definition Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 May 21 2014 15:34:39 Broadcom Logger v0.1 May 21 2014 15:33:27 Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 /proc/ra_info created NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 128k freed init started: BusyBox v1.00 (2014.05.21-07:38+0000) multi-call binary BusyBox v1.00 (2014.05.21-07:38+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... 173 pktflow: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Sep 24 2010 17:51:48 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Sep 24 2010 17:51:48 Broadcom Packet CMF (Experimental) Char Driver v0.1 Sep 24 2010 17:51:45 Registered<232> Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Sep 24 2010 17:51:45 Loaded CT_HOTPLUG_MONITOR bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6368B2 Ethernet Network Device v0.1 May 21 2014 15:33:32 ETH Init: 180 tx BDs at 0xa3a08000 ETH Init: 400 rx BDs at 0xa3b4b000 ETH Init: 400 rx BDs at 0xa3b4a000 ######## ethsw_init_table:98 ####### switch_port_phyid[0]=1 ######## ethsw_init_table:98 ####### switch_port_phyid[1]=2 ######## ethsw_init_table:98 ####### switch_port_phyid[2]=3 ######## ethsw_init_table:98 ####### switch_port_phyid[3]=4 /proc/buffer16 created dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered Broadcom Packet CMF (Experimental) SWC RESET. Broadcom Packet CMF (Experimental) SWC INITIALIZED. Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Sep 24 2010 17:51:46 Registered Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Sep 24 2010 17:51:46 Registered Broadcom Packet CMF (Experimental) ENABLED. ===== Found Interface name mapping : 96368MT-1341N1 ===== eth0: MAC Address: 38:72:C0:58:32:50 eth1: MAC Address: 38:72:C0:58:32:50 eth2: MAC Address: 38:72:C0:58:32:50 eth3: MAC Address: 38:72:C0:58:32:50 PCI: Enabling device 0000:00:01.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:01.0 to 64 wl:srom strapped wl:(srom strapped) probe/present=0 wl:srom not detected, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43222_map.bin wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.100.123.0.cpe4.06L03.4 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs p8021ag: p8021ag_init entry Broadcom 802.1Q VLAN Interface, v0.1 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems usbcore: registered new interface driver hso hso: 1.6-Option:USB High Speed Option driver ===== Comtrend Release Version A641-406TO2-C04_R01 ===== interface ptm0.2 does not exist! SIOCGIFFLAGS: No such device SIOCGIFFLAGS: No such device SIOCGIFFLAGS: No such device interface atm1 does not exist! SIOCGIFFLAGS: No such device SIOCGIFFLAGS: No such device SIOCGIFFLAGS: No such device ip_tables: (C) 2000-2006 Netfilter Core Team ip6_tables: (C) 2000-2006 Netfilter Core Team [TO2] implement DSCP rule RADVDAdvLinkMTUUserMode[0] mtu:1492 init dad_transmits 1 init ns_retrans_time 1000 device eth0 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### Implement WOL arp ######## bcm63xx_enet_open:1042 ####### dev->base_addr=0 phyport:0 0 ADDRCONF(NETDEV_UP): eth0: link is not ready ssk:error:16.127:rcl_lanEthIntfObject:1384:================> macControlEnabledInterface: echo > /var/macControlEnabledInterface device eth2 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### Implement WOL arp ######## bcm63xx_enet_open:1042 ####### dev->base_addr=2 phyport:1 2 ADDRCONF(NETDEV_UP): eth2: link is not ready ssk:error:16.981:rcl_lanEthIntfObject:1384:================> macControlEnabledInterface: echo > /var/macControlEnabledInterface device eth3 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### Implement WOL arp ######## bcm63xx_enet_open:1042 ####### dev->base_addr=3 phyport:2 3 ADDRCONF(NETDEV_UP): eth3: link is not ready ssk:error:17.843:rcl_lanEthIntfObject:1384:================> macControlEnabledInterface: echo > /var/macControlEnabledInterface device wl0 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### Implement WOL arp WLmngr Daemon is running optarg=0 shmId=0 br0: port 4(wl0) entering forwarding state wlevt_init@107: opened loopback socket 4 wlevt is ready for new msg... Success RADVDAdvLinkMTUUserMode[0] mtu:1492 device eth1 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### ######## bcm63xx_enet_open:1042 ####### dev->base_addr=1 phyport:0 1 ADDRCONF(NETDEV_UP): eth1: link is not ready [ll] User Setting mdoe - cnt=4 RTNETLINK answers: Cannot assign requested address @@ cmd:ip -6 addr del fe80::3a72:c0ff:fe58:3250/64 dev br0 RTNETLINK answers: File exists @@ cmd:ip -6 addr add fe80::0:0:0:1/64 dev br0 ssk:error:19.899:rcl_lanEthIntfObject:1384:======*** dslThread dslPid=809 ==========> macCBcmAdsl_Initialize=0xC012E6E0, g_pFnNotifyCallback=0xC0173024 ontrolEnabledInt[Enable phyReXmt | Ginp] erface: echo > /var/macControlEnabledInterface Clocks for QPROC and AFE are being aligned with step through ... AFE is aligned, i = 064, PhaseValue = -050, PhaseCntl = 0x3FC00000 QPROC is aligned, i = 015, PhaseValue = 0050, PhaseCntl = 0x3FC0400F Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x78 AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f pSdramPHY=0xA3FFFFF8, 0xF7F37B72 0xF6F17F71 *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xDD824 => 0x114AA0 *** AdslCoreSharedMemInit: shareMemSize=120125(120128) AdslCoreHwReset: pLocSbSta=82700000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3F9E25C [Enable phyReXmt | Ginp] Serial number EOC(mac):38:72:C0:58:32:50 Version Number of EOC(buid time):201405210000 ***BcmDiagsMgrRegisterClient: 0 *** dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered XTM Init: 400 rx BDs at 0xa2e9b000 XTM Init: 100 rx BDs at 0xa2ef1800 Register interface ppp1 !! Register interface ppp0.1 !! monitor task is initialized pid= 257 CT_ATCPOLL:error:23.630:getAvailableUsbDongleList:160:Can't open proc file /var/donglemap2 echo 005d0140 > /proc/switch set active notify "InternetGatewayDevice.GatewayInfo.ManufacturerOUI" set active notify "InternetGatewayDevice.GatewayInfo.SerialNumber" set active notify "InternetGatewayDevice.GatewayInfo.ProductClass" set active notify "InternetGatewayDevice.GatewayInfo.ManufacturerOUI" set active notify "InternetGatewayDevice.GatewayInfo.SerialNumber" set active notify "InternetGatewayDevice.GatewayInfo.ProductClass" device wl0 left promiscuous mode br0: port 4(wl0) entering disabled state #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### device wl0 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### br0: port 4(wl0) entering forwarding state br0: port 4(wl0) entering disabled state br0: port 4(wl0) entering forwarding state br0: port 4(wl0) entering disabled state There is no Predefined DevicePin in CFE WPS Device PIN = 18836486 Implement WOL arp Setting SSID: "Skywalker" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" [0] ncis:13 channel:6 gAPs:1 realAP:1 aps:65535 [1] ncis:13 channel:7 gAPs:1 realAP:0 aps:65535 [2] ncis:13 channel:8 gAPs:1 realAP:0 aps:65535 [3] ncis:13 channel:9 gAPs:0 realAP:0 aps:65535 [4] ncis:13 channel:10 gAPs:0 realAP:0 aps:65535 [5] ncis:13 channel:11 gAPs:0 realAP:0 aps:65535 [6] ncis:13 channel:12 gAPs:0 realAP:0 aps:65535 [7] ncis:13 channel:13 gAPs:0 realAP:0 aps:65535 [8] ncis:13 channel:1 gAPs:0 realAP:0 aps:65535 [9] ncis:13 channel:2 gAPs:0 realAP:0 aps:65535 [10] ncis:13 channel:3 gAPs:0 realAP:0 aps:65535 [11] ncis:13 channel:4 gAPs:1 realAP:0 aps:65535 [12] ncis:13 channel:5 gAPs:1 realAP:0 aps:65535 @@ ci[i].gAPs:1 lastFreeAPs:65535 select free channel 7 gAPs:1 @@ ci[i].gAPs:1 lastFreeAPs:1 @@ ci[i].gAPs:0 lastFreeAPs:1 select free channel 9 gAPs:0 @@ ci[i].gAPs:0 lastFreeAPs:0 @@ ci[i].gAPs:0 lastFreeAPs:0 @@ ci[i].gAPs:0 lastFreeAPs:0 @@ ci[i].gAPs:0 lastFreeAPs:0 @@ ci[i].gAPs:0 lastFreeAPs:0 @@ ci[i].gAPs:0 lastFreeAPs:0 @@ ci[i].gAPs:0 lastFreeAPs:0 @@ ci[i].gAPs:1 lastFreeAPs:0 @@ ci[i].gAPs:1 lastFreeAPs:0 @ selected channe 9 bandwidth 20MHz chanspec 0x2b09 selected device wl0 left promiscuous mode br0: port 4(wl0) entering disabled state #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### device wl0 entered promiscuous mode #### Brctl_Port_Base_VLAN_config:60 #### #### Brctl_Port_Base_VLAN_config:84 #### br0: port 4(wl0) entering forwarding state Reaped 975 UPnP daemon is ready to run Implement WOL arp Del ip6 route [br1] ssk:error:37.334:checkDongleState:195:Wan link(3G) went from up->down, send event msg ssk:error:37.335:checkDongleState:225:3G WAN not configured


OpenWrt bootlog

CFE version 1.0.37-106.24-31 for BCM96368 (32bit,SP,BE) Build Date: 2012-06-29 16:09:03 (lain@SW1-BCM-04) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB Total Flash size: 8192K with 135 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-15) : 96368MT-1341N1 Number of MAC Addresses (1-32) : 32 Base MAC Address : 38:72:c0:58:32:50 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Serial Number : 129QJA14892 Default PSK key : 6CvVFfbWir *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from only image (0xb8010000) ... Code Address: 0x80A00000, Entry Address: 0x80a00000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80a00000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80a00000 [ 0.000000] Linux version 4.1.5 (mates@mates-e6410) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46694) ) #8 SMP Sat Aug 22 13:07:06 CEST 2015 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.24-31 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board: board name: 96368MT-1341N1 [ 0.000000] MIPS: machine is Comtrend VR-3026e [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] PERCPU: Embedded 10 pages/cpu @81086000 s9904 r8192 d22864 u40960 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 59596K/65536K available (2963K kernel code, 137K rwdata, 592K rodata, 1292K init, 193K bss, 5940K reserved, 0K cma-reserved) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:256 [ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000016] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008719] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.047015] pid_max: default: 32768 minimum: 301 [ 0.052481] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.059275] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.073465] SMP: Booting CPU1... [ 11.922751] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 11.922769] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 11.923156] CPU1 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.129706] Synchronize counters for CPU 1: [ 0.129707] SMP: CPU1 is running [ 0.129732] done. [ 0.129950] Brought up 2 CPUs [ 0.149136] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.160700] NET: Registered protocol family 16 [ 0.171586] registering PCI controller with io_map_base unset [ 0.203346] PCI host bridge to bus 0000:00 [ 0.207664] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.214815] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.221706] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.228668] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.244795] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.255324] Switched to clocksource MIPS [ 0.262928] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.292345] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.357548] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.365970] NET: Registered protocol family 2 [ 0.372403] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.379665] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.386239] TCP: Hash tables configured (established 1024 bind 1024) [ 0.393023] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.399098] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.406165] NET: Registered protocol family 1 [ 0.413726] futex hash table entries: 512 (order: 1, 8192 bytes) [ 0.421972] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.428047] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.440251] io scheduler noop registered [ 0.444344] io scheduler deadline registered (default) [ 0.452591] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart [ 0.462290] console [ttyS0] enabled [ 0.462290] console [ttyS0] enabled [ 0.469432] bootconsole [early0] disabled [ 0.469432] bootconsole [early0] disabled [ 0.478979] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.486869] 18000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb [ 0.497346] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.502617] Amd/Fujitsu Extended Query version 1.1. [ 0.507794] number of CFI chips: 1 [ 0.511716] bcm63xxpart: CFE boot tag found with version 6 and board type 96368MT-1341N1 [ 0.520220] 5 bcm63xxpart partitions found on MTD device 18000000.nor [ 0.526878] Creating 5 MTD partitions on "18000000.nor": [ 0.532353] 0x000000000000-0x000000010000 : "CFE" [ 0.539886] 0x000000010100-0x00000014ce6a : "kernel" [ 0.547738] 0x00000014ce6a-0x0000007f0000 : "rootfs" [ 0.555590] mtd: device 2 (rootfs) set to be root filesystem [ 0.561460] 1 squashfs-split partitions found on MTD device rootfs [ 0.567834] 0x000000340000-0x0000007f0000 : "rootfs_data" [ 0.576144] 0x000000010000-0x0000007f0000 : "linux" [ 0.583998] 0x0000007f0000-0x000000800000 : "nvram" [ 0.593787] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.640734] b53_common: found switch: BCM63xx, rev 0 [ 0.646716] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.659075] NET: Registered protocol family 17 [ 0.663840] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.676859] 8021q: 802.1Q VLAN Support v1.8 [ 0.693025] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.716388] Freeing unused kernel memory: 1292K (803ad000 - 804f0000) [ 2.244872] init: Console is alive [ 2.248894] init: - watchdog - [ 4.253699] init: - preinit - [ 4.752599] random: procd urandom read with 65 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.239994] jffs2: notice: (256) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 8.257965] mount_root: switching to jffs2 overlay [ 8.313823] procd: - early - [ 8.317016] procd: - watchdog - [ 9.152301] procd: - ubus - [ 9.707298] random: nonblocking pool is initialized [ 10.172797] procd: - init - Please press Enter to activate this console. [ 11.550078] NET: Registered protocol family 10 [ 11.565159] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.591477] Loading modules backported from Linux version master-2015-07-21-0-g47cd203 [ 11.599690] Backport generated by backports.git backports-20150626-0-gc1a4168 [ 11.612128] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.633459] nf_conntrack version 0.5.0 (951 buckets, 3804 max) [ 11.741108] xt_time: kernel timezone is -0000 [ 11.785685] cfg80211: World regulatory domain updated: [ 11.791119] cfg80211: DFS Master region: unset [ 11.795643] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.805726] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.813982] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.822216] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 11.830479] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 11.840238] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 11.850051] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.858512] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.866768] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 11.992918] PPP generic driver version 2.4.2 [ 12.001677] NET: Registered protocol family 24 [ 12.052053] b43-phy0: Broadcom 43222 WLAN found (core revision 16) [ 12.091255] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 [ 12.097556] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 6, Version 0 [ 12.116669] Broadcom 43xx driver loaded [ Features: PNL ] [ 20.316765] device eth0.1 entered promiscuous mode [ 20.321865] device eth0 entered promiscuous mode [ 20.341960] br-lan: port 1(eth0.1) entered forwarding state [ 20.348070] br-lan: port 1(eth0.1) entered forwarding state [ 22.351201] br-lan: port 1(eth0.1) entered forwarding state [ 62.381078] done. [ 62.383064] jffs2: notice: (761) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.


Notes

Tags

toh/comtrend/vr3026e.txt · Last modified: 2017/05/20 11:32 by tmomas