User Tools

Site Tools


toh:comtrend:vr3032u

Comtrend VR-3032u

GPL Source Code (Comtrend)

Not supported (WIP).

Installation

Flashing ANY Firmware

You must set your TCP/IP v4 protocol to:

  1. IP: 192.168.1.2
  2. Netmask: 255.255.255.0
  3. Gateway: 192.168.1.1
  4. DNS: (optional, can be blank).

Then:

  1. Power off the router.
  2. Press reset button near the antenna.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Acces to http://192.168.1.1 and upload binary file.
  5. Wait until router reboots.

Hardware

Info

Architecture: MIPS
Vendor: Broadcom
Bootloader: CFE
Board ID: 963168M-1841N1
System-On-Chip: Broadcom BCM63168
CPU/Speed BMIPS4350 v8.0 / 400 MHz
NAND: 128 MiB (MX30LF1G08AA-TI)
RAM 64 MiB / DDR2 (EM68816CWQD-25H)
Wireless BCM6362 (14e4:6362) 802.11b/g/n (SoC)
Antenna 2x
Ethernet: Integrated BCM63168 w/ vlan support swconfig
USB Yes
Power adapter 12V DC 1A / UP0121B-12PE
Serial: Yes
JTAG: ?

Photos

Case:

Board:

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

PCB with markings for serial connection

Bootlogs

OEM Bootlog

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR2 SIZ4 SIZ3 SIZ2 SIZ1 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN FPS0 BT01 0002 STOP NAN9 NAN3 RFS1 NAN5 CFE version 1.0.38-112.118-11 for BCM963268 (32bit,SP,BE) Build Date: å12月 27 11:54:52 CST 2012 (camille@SW1-BCM-02) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name , id 0xc2f1 block 128KB size 131072KB Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-28) : 963168M-1841N1 Number of MAC Addresses (1-32) : 32 Base MAC Address : f8:8e:85:ed:70:d3 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 WLAN Password : 93ydNwyxeEiqzXKtUSgd Serial Number : 1463032UXXF-AA002895 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from only image (0xb8020000) ... nand_flash_read_buf(): Attempt to read bad nand block 1 nand_flash_read_buf(): Attempt to read bad nand block 1 Decompression OK! Entry at 0x802e5950 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x802e5950 Linux version 2.6.30 (joba@SW1-BCM-02) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Wed Apr 3 09:57:13 CST 2013 BCM Flash API. Flash device is not found. 963168M-1841N1 prom init CPU revision is: 0002a080 (Broadcom4350) DSL SDRAM reserved: 0x132000 Determined physical RAM map: memory: 03ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003ece On node 0 totalpages: 16078 free_area_init_node: node 0, pgdat 80384c90, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11888 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 59696k/64312k available (2934k kernel code, 4596k reserved, 623k data, 148k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Apr 3 2013 09:54:51 CPU revision is: 0002a080 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 828 bytes NET: Registered protocol family 16 Total Flash size: 0K with -1 sectors Internal 1P2 VREG will be shutdown if unused...Used, leave it on (00009081-00008a7e=1539>=300) registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff] pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: disabled pci 0000:01:00.0: PREFETCH window: disabled PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Apr 3 2013 09:57:00 initialized Broadcom GBPM v0.1 Apr 3 2013 09:57:01 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 116 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 Failed to read image tag from flash Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 brcmnand_read_id: CS0: dev_id=c2f1801d After: NandSelect=40000001, nandConfig=15142200 DevId c2f1801d may not be supported. Will use config info Spare Area Size = 16B/512B Block size=00020000, erase shift=17 NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 ECC level changed to 15 OOB size changed to 16 BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0 Found NAND on CS0: ACC=f7ff1010, cfg=15142200, flashId=c2f1801d, tim1=6574845b, tim2=00001e96 BrcmNAND version = 0x0400 128MB @00000000 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=83a38198, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 nand_read_bbt: Bad block at 0x00020000 nand_read_bbt: Bad block at 0x02a40000 nand_read_bbt: Bad block at 0x06740000 nand_read_bbt: Bad block at 0x07320000 brcmnandCET: Status -> Deferred brcmnand_scan 99 Creating 4 MTD partitions on "brcmnand.0": 0x000000020000-0x000003d80000 : "rootfs" 0x000003d80000-0x000007ae0000 : "rootfs_update" 0x000007b00000-0x000007f00000 : "data" 0x000000000000-0x000000020000 : "nvram" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected @@@@@ hub_power_on:541 @@@@@ ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected @@@@@ hub_power_on:541 @@@@@ usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0xc007 is enabled PCIe: No device found - Powering down Serial: BCM63XX driver $Revision: 3.00 $ Magic SysRq enabled (type ^ h for list of supported commands) ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX bcmPktDma_init: Broadcom Packet DMA Library initialized Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Apr 3 2013 09:56:47 GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 148k freed init started: BusyBox v1.17.2 (2013-04-03 09:59:22 CST) starting pid 222, tty '': '/etc/init.d/rcS' usbfs: unrecognised mount option "defaults" or missing value usbfs: mount parameter error. mount: mounting /dev/sda1 on /mnt failed: No such device or address starting pid 232, tty '': '-/bin/sh' BusyBox v1.17.2 (2013-04-03 09:59:22 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... -/bin/sh: ct_hotplug_monitor: not found chipinfo: module license 'proprietary' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Apr 3 2013 09:55:30 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers=4766, buf size=2112 Broadcom BPM Module Char Driver v0.1 Apr 3 2013 09:55:24 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Apr 3 2013 09:55:31 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Apr 3 2013 09:55:31 chipId 0x631680D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Apr 3 2013 09:55:25 Registered <241> FAP Debug values at 0x00000010 0x00000010 Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done FAP Debug values at 0xa2a5b200 0xa2a9b200 Allocated FAP0 TM SDRAM Queue Storage (a2a614bc) : 219456 bytes @ a2ac0000 Allocated FAP1 TM SDRAM Queue Storage (a2aa14bc) : 219456 bytes @ a2b00000 [NTC fapProto] fapReset : Reset FAP Protocol layer fapDrv_construct: FAP0: pManagedMemory=b0820710. wastage 8 bytes fapDrv_construct: FAP1: pManagedMemory=b0a20710. wastage 8 bytes bcmPktDma_bind: FAP Driver binding successfull [FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6432>, free <224>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6432>, free <224>, total<8192> [FAP0] PSM : addr<0x80002000>, used <24412>, free <164>, total <24576> [FAP1] PSM : addr<0x80002000>, used <24412>, free <164>, total <24576> [FAP0] Flows supported: 222 (dsp 54, psm 44, qsm 124) [FAP1] Flows supported: 222 (dsp 54, psm 44, qsm 124) [FAP0] DQM : availableMemory 15464 bytes, nextByteAddress 0xE0010398 [FAP1] DQM : availableMemory 15464 bytes, nextByteAddress 0xE0010398 [FAP0] GSO Buffer set to 0x00000000 [FAP1] GSO Buffer set to 0x00000000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. [FAP0] FAP TM: ON [FAP1] FAP TM: ON bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM63168D0 Ethernet Network Device v0.1 Apr 3 2013 09:56:41 fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b0820710 bytes remaining 7000 ETH Init: Ch:0 - 200 tx BDs at 0xb0820710 fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a20710 bytes remaining 7000 ETH Init: Ch:1 - 200 tx BDs at 0xb0a20710 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b08216b0 bytes remaining 2184 ETH Init: Ch:0 - 600 rx BDs at 0xb08216b0 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a216b0 bytes remaining 2184 ETH Init: Ch:1 - 600 rx BDs at 0xb0a216b0 For port 3; changing the MII adv to 0x1e1 changing the GMII adv to 0x0 Error: kerSysRegisterDyingGaspHandler: list head is null eth1: MAC Address: F8:8E:85:ED:70:D3 eth2: MAC Address: F8:8E:85:ED:70:D3 eth3: MAC Address: F8:8E:85:ED:70:D3 eth0: MAC Address: F8:8E:85:ED:70:D3 [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Adress Resolution Logic Processor (ARL) Char Driver v0.1 Apr 3 2013 09:55:23 Registered <245> [ERROR fap] keepAliveWd_timer,722: keepAliveWd_timer: Detected scribble error for FAP0 [ERROR fap] keepAliveWd_timer,723: PSM scribble 0 (b0820024)=0x00005f5c / 0x00005f4c [ERROR fap] keepAliveWd_timer,724: PSM scribble 1 (b0820028)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,725: PSM scribble 2 (b08206f4)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,726: PSM scribble 3 (b0823208)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,727: PSM scribble 4 (b0823210)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,728: QSM scribble 0 (b0c04000)=0x00005f5c / 0x0000c398 [ERROR fap] keepAliveWd_timer,729: QSM scribble 1 (b0c10394)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,722: keepAliveWd_timer: Detected scribble error for FAP1 [ERROR fap] keepAliveWd_timer,723: PSM scribble 0 (b0a20024)=0x00005f5c / 0x00005f4c [ERROR fap] keepAliveWd_timer,724: PSM scribble 1 (b0a20028)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,725: PSM scribble 2 (b0a206f4)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,726: PSM scribble 3 (b0a23208)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,727: PSM scribble 4 (b0a23210)=0x12345678 / 0x12345678 [ERROR fap] keepAliveWd_timer,728: QSM scribble 0 (b0e04000)=0x00005f5c / 0x0000c398 [ERROR fap] keepAliveWd_timer,729: QSM scribble 1 (b0e10394)=0x12345678 / 0x12345678 --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=3097 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=256 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_vars.bin Failed to open srom image from '/etc/wlan/bcm6362_vars.bin'. wl:loading /etc/wlan/bcm6362_map.bin wl0: Broadcom BCM435f 802.11 Wireless Controller 5.100.138.2008.cpe4.12L06B.4 Error: kerSysRegisterDyingGaspHandler: list head is null Broadcom 802.1Q VLAN Interface, v0.1 usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems hso_init - tty_register_driver failed(-16) insmod: can't insert '/lib/modules/2.6.30/kernel/drivers/usb/serial/hso.ko': Device or resource busy ===== Comtrend Release Version VA31-412JAZ-C03_R01 ===== killall: syslogd: no process killed Energy Efficient Ethernet is disabled smtpEnblSsl 0 Auto-negotiation enabled. Link is down device eth0 entered promiscuous mode ip_tables: (C) 2000-2006 Netfilter Core Team Auto-negotiation enabled. Link is down device eth1 entered promiscuous mode Auto-negotiation enabled. Link is down device eth2 entered promiscuous mode Auto-negotiation enabled. Link is down device eth3 entered promiscuous mode device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state BcmAdsl_Initialize=0xC01F8C60, g_pFnNotifyCallback=0xC022EF24 WLmngr Daemon is running optarg=0 shmId=0 wlevt is ready for new msg... lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA3FFFFF8, 0x7FF1F3F9 0x7FF3FFFB *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xE4C54 => 0x11B4C0 *** AdslCoreSharedMemInit: shareMemSize=92957(92960) AdslCoreHwReset: pLocSbSta=81d80000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3FA3F70 ***BcmDiagsMgrRegisterClient: 0 ***Error: kerSysRegisterDyingGaspHandler: list head is null fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22980 bytes remaining 584 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22980 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a22fc0 bytes remaining 456 XTM Init: Ch:1 - 16 rx BDs at 0xb0a22fc0 bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system bcmxtmcfg: gulBondDslMonitorValid = 1 Register interface ppp0.1 !! ssk:error:31.009:rcl_wanPppConnPortmappingObject:113:This is system bootup, so don't add the Virtual Server ssk:error:31.010:rcl_wanPppConnPortmappingObject:113Register interface ppp1.1 !! :This is system bootup, so don't add the Virtual Server ssk:error:31.027:rcl_wanPppConnPortmappingObject:113:This is system bootup, so don't add the Virtual Server ssk:error:31.028:rcl_wanPppConnPortmappingObject:113:This is system bootup, so don't add the Virtual Server monitor task is initialized pid= 347 There is no Predefined DevicePin in CFE WPS Device PIN = 96567111 br0: port 5(wl0) entering disabled state device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state br0: port 5(wl0) entering disabled state Setting SSID: "JAZZTEL_70D4" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state Offset1:131072 Offset2:64487424 acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x2b01


Tags

toh/comtrend/vr3032u.txt · Last modified: 2017/05/20 11:33 by tmomas