User Tools

Site Tools


toh:easyacc:wizard8800

EasyAcc Wi-Stor Wizard 4in1 wireless storage 8800

Info Page http://www.nikktech.com/main/articles/gadgets/wireless-readers/2706-easyacc-wi-stor-wizard-4-in-1-portable-device

If you can confirm that OpenWrt is running on this device (i.e. you or someone else has tested it), please update the data accordingly. → Click View/Edit data

Hardware

Overview

CPU MIPS 24KEc V5.0
Architecture: MIPS
System-On-Chip: 360 MHZ Ralink RT5350 id:1 rev:3
Flash: 8 MB Winbond W25Q32BV
RAM: 32 MB Etron EM63A165TS-6G
Ethernet: Yes 1x (10/100Mbit )
USB: Yes 2x (USB Battery Charging, EHCI/OHCI)
Power Supply: 8800mAh Li-ion battery (4 Cell 3,6V ICR-18650NH )

CPU Info

root@OpenWrt:~# cat /proc/cpuinfo
system type             : Ralink RT5350 id:1 rev:3
machine                 : EASYACC WI-STOR WIZARD 8800
processor               : 0
cpu model               : MIPS 24KEc V4.12
BogoMIPS                : 239.61
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : yes, count: 4, address/irw mask: [0x0000, 0x00a0, 0x0720, 0x0728]
isa                     : mips1 mips2 mips32r1 mips32r2
ASEs implemented        : mips16 dsp
shadow register sets    : 1
kscratch registers      : 0
core                    : 0
VCED exceptions         : not available
VCEI exceptions         : not available

MEM Info

root@OpenWrt:/# cat /proc/meminfo
MemTotal:          29556 kB
MemFree:           13068 kB
Buffers:            1844 kB
Cached:             5340 kB
SwapCached:            0 kB
Active:             3924 kB
Inactive:           4456 kB
Active(anon):       1216 kB
Inactive(anon):       20 kB
Active(file):       2708 kB
Inactive(file):     4436 kB
Unevictable:           0 kB
Mlocked:               0 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                 0 kB
Writeback:             0 kB
AnonPages:          1212 kB
Mapped:             1236 kB
Shmem:                40 kB
Slab:               4356 kB
SReclaimable:        952 kB
SUnreclaim:         3404 kB
KernelStack:         288 kB
PageTables:          180 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:       14776 kB
Committed_AS:       3368 kB
VmallocTotal:    1048372 kB
VmallocUsed:         552 kB
VmallocChunk:    1044204 kB

Images

Serial

Pinout

1 2 3 4
TX RX GND VCC

Serial connection parameters: 57600, 8N1

Linux Connect

sudo screen /dev/ttyUSB3 57600

Bootlog

U-Boot 1.1.3 (Sep 13 2012 - 16:39:43) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb4000 spi_wait_nsec: 42 spi device id: ef 40 16 0 0 (40160000) find flash: W25Q32BV raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 4.0.1.0 -------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 256 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 32 MBytes Flash component: SPI Flash Date:Sep 13 2012 Time:16:39:43 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 360 MHZ #### estimate memory size =32 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 . Image Name: Linux Kernel Image Created: 2014-04-16 18:22:25 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 982205 Bytes = 959.2 kB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:efcbd ............... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 32 Starting kernel ... [ 0.000000] Linux version 3.10.36 (openwrt@openwrt) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40477) ) #9 Wed Apr 16 20:11:30 CEST 2014 [ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is EASYACC WI-STOR WIZARD 8800 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=00073523 [ 0.000000] Readback ErrCtl register=00073523 [ 0.000000] Memory: 29356k/32768k available (2134k kernel code, 3412k reserved, 543k data, 200k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 360MHz [ 0.000000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] pinctrl core: initialized pinctrl subsystem [ 0.090000] NET: Registered protocol family 16 [ 0.110000] rt2880-pinmux pinctrl.1: invalid group "rgmii" for function "gpio" [ 0.120000] rt2880-pinmux pinctrl.1: invalid group "mdio" for function "gpio" [ 0.150000] bio: create slab <bio-0> at 0 [ 0.160000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.170000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.180000] Switching to clocksource MIPS [ 0.190000] NET: Registered protocol family 2 [ 0.200000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.220000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.230000] TCP: Hash tables configured (established 512 bind 512) [ 0.240000] TCP: reno registered [ 0.250000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.270000] NET: Registered protocol family 1 [ 0.280000] rt-timer 10000100.timer: maximum frequncy is 7324Hz [ 0.330000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.350000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.370000] msgmni has been set to 57 [ 0.380000] io scheduler noop registered [ 0.380000] io scheduler deadline registered (default) [ 0.400000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.410000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.430000] console [ttyS0] enabled, bootconsole disabled [ 0.430000] console [ttyS0] enabled, bootconsole disabled [ 0.460000] m25p80 spi32766.0: w25q32 (4096 Kbytes) [ 0.470000] 4 ofpart partitions found on MTD device spi32766.0 [ 0.480000] Creating 4 MTD partitions on "spi32766.0": [ 0.490000] 0x000000000000-0x000000030000 : "u-boot" [ 0.510000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.520000] 0x000000040000-0x000000050000 : "factory" [ 0.530000] 0x000000050000-0x000000800000 : "firmware" [ 0.540000] mtd: partition "firmware" extends beyond the end of device "spi32766.0" -- size truncated to 0x3b0000 [ 0.570000] 0x00000013fcfd-0x000000400000 : "rootfs" [ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.610000] mtd: device 4 (rootfs) set to be root filesystem [ 0.620000] mtd: partition "rootfs_data" created automatically, ofs=0x390000, len=0x70000 [ 0.640000] 0x000000390000-0x000000400000 : "rootfs_data" [ 0.660000] eth0: done loading [ 0.670000] rt3xxx-usbphy ubsphy.3: loaded [ 0.680000] rt2880_wdt 10000120.watchdog: Initialized [ 0.690000] TCP: cubic registered [ 0.700000] NET: Registered protocol family 17 [ 0.710000] 8021q: 802.1Q VLAN Support v1.8 [ 0.730000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.750000] Freeing unused kernel memory: 200K (8029e000 - 802d0000) procd: Console is alive procd: - watchdog - procd: - preinit - [ 6.860000] rt305x-esw 10110000.esw: link changed 0x00 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.710000] usbcore: registered new interface driver usbfs [ 8.720000] usbcore: registered new interface driver hub [ 8.730000] usbcore: registered new device driver usb [ 8.770000] SCSI subsystem initialized [ 8.790000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.800000] ehci-platform: EHCI generic platform driver [ 9.010000] rt3xxx-usbphy ubsphy.3: remote usb device wakeup disabled [ 9.020000] rt3xxx-usbphy ubsphy.3: UTMI 16bit 30MHz [ 9.030000] ehci-platform 101c0000.ehci: EHCI Host Controller [ 9.050000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 9.060000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 9.100000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 9.110000] hub 1-0:1.0: USB hub found [ 9.120000] hub 1-0:1.0: 1 port detected [ 9.140000] dwc_otg: version 2.72a 24-JUN-2008 [ 9.160000] usbcore: registered new interface driver usb-storage [ 9.450000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 9.610000] hub 1-1:1.0: USB hub found [ 9.620000] hub 1-1:1.0: 4 ports detected [ 9.910000] usb 1-1.2: new high-speed USB device number 3 using ehci-platform [ 10.030000] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 10.050000] scsi0 : usb-storage 1-1.2:1.0 [ 10.140000] usb 1-1.4: new high-speed USB device number 4 using ehci-platform kmod: ran 1 iterations [ 11.060000] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 0207 PQ: 0 ANSI: 0 [ 11.240000] sd 0:0:0:0: [sda] 15523840 512-byte logical blocks: (7.94 GB/7.40 GiB) [ 11.270000] sd 0:0:0:0: [sda] Write Protect is off [ 11.290000] sd 0:0:0:0: [sda] No Caching mode page found [ 11.300000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.360000] sd 0:0:0:0: [sda] No Caching mode page found [ 11.380000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.420000] sda: sda1 [ 11.470000] sd 0:0:0:0: [sda] No Caching mode page found [ 11.480000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.490000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 11.750000] jffs2: notice: (294) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found. block: extroot: no root or overlay mount defined jffs2 is ready [ 12.050000] jffs2: notice: (286) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found. switching to jffs2 procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 14.970000] NET: Registered protocol family 10 [ 15.000000] nf_conntrack version 0.5.0 (461 buckets, 1844 max) [ 15.020000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 15.070000] fuse init (API version 7.22) [ 15.090000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2 [ 15.110000] Backport generated by backports.git backports-20140221-0-g8e94650 [ 15.130000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.190000] usbcore: registered new interface driver ums-alauda [ 15.200000] usbcore: registered new interface driver ums-cypress [ 15.220000] usbcore: registered new interface driver ums-datafab [ 15.240000] usbcore: registered new interface driver ums-freecom [ 15.250000] usbcore: registered new interface driver ums-isd200 [ 15.270000] usbcore: registered new interface driver ums-jumpshot [ 15.290000] usbcore: registered new interface driver ums-karma [ 15.300000] usbcore: registered new interface driver ums-sddr09 [ 15.320000] usbcore: registered new interface driver ums-sddr55 [ 15.340000] usbcore: registered new interface driver ums-usbat [ 15.390000] xt_time: kernel timezone is -0000 [ 15.450000] cfg80211: Calling CRDA to update world regulatory domain [ 15.460000] cfg80211: World regulatory domain updated: [ 15.470000] cfg80211: DFS Master region: unset [ 15.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 15.500000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 15.520000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 15.530000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 15.550000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 15.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 15.580000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 15.680000] PPP generic driver version 2.4.2 [ 15.700000] NET: Registered protocol family 24 [ 15.760000] rt2800_wmac 10180000.wmac: failed to load eeprom property [ 15.770000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'. [ 15.790000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected [ 15.810000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected procd: - init complete - [ 26.210000] device eth0 entered promiscuous mode [ 26.230000] br-lan: port 1(eth0) entered forwarding state [ 26.240000] br-lan: port 1(eth0) entered forwarding state [ 28.240000] br-lan: port 1(eth0) entered forwarding state BusyBox v1.19.4 (2014-04-15 21:10:54 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r40477) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#


Installation

Flash Layout

root@OpenWrt:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00030000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "factory"
mtd3: 003b0000 00010000 "firmware"
mtd4: 002c0303 00010000 "rootfs"
mtd5: 00070000 00010000 "rootfs_data"

TFTP Method

Tags

toh/easyacc/wizard8800.txt · Last modified: 2016/03/12 03:29 by tmomas