User Tools

Site Tools


toh:netgear:r7000

Netgear Nighthawk R7000

NETGEAR's R7000 "Nighthawk" is a second generation Broadcom 802.11ac AC1900 router with storage sharing USB 2.0 & 3.0 ports.

R7000

Supported Versions

Ver Supported since Notes
v1 Chaos Calmer 15.05 Both wireless radios are unsupported (no FOSS driver support).

Hardware Highlights

Ver CPU Ram Flash Network Wireless USB Serial JTag Wiki FCC
v1 Broadcom BCM4709A0 dualcore 1 GHz 256 MiB 128 MiB NAND 1 WAN + 4x LAN (GBit) BCM4360 [ac 3x3:3] + BCM4360 [bgn 3x3:3] USB2.0 (1x) USB3.0 (1x) yes ? here here

Installation

Flash Layout

FIXME

root@OpenWrt:~# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00080000 00020000 "boot"
mtd1: 00180000 00020000 "nvram"
mtd2: 02000000 00020000 "firmware"
mtd3: 003fffe4 00020000 "linux"
mtd4: 01c00000 00020000 "ubi"
mtd5: 00040000 00020000 "board_data"
mtd6: 00040000 00020000 "POT"
mtd7: 00180000 00020000 "POT"
mtd8: 00040000 00020000 "ML"
mtd9: 00040000 00020000 "ML"
mtd10: 00040000 00020000 "ML"
mtd11: 00040000 00020000 "ML"
mtd12: 00040000 00020000 "ML"
mtd13: 05ac0000 00020000 "ML"

Upgrading OpenWrt

Basic configuration

Failsafe mode

Buttons

hardware.button on howto use and configure the hardware button(s).

Name GPIO Polarity
WPS 4 Active low
Wlan 5 Active low
Reset 6 Active low

LEDs

Color Name GPIO Polarity
White Power LED 2 Active low
Amber Power LED 3 Active low
White Wlan 5Ghz LED 12 Active low
White Wlan 2.4Ghz LED 13 Active low
White WPS Button 14 Active high
White Wlan Button 15 Active high
White USB_1 LED 17 Active low
White USB_2 LED 18 Active low

Hardware

Info

General
Brand Netgear
Model R7000
Versions
Device Type Router
Availability Available 2016
Comments - general
OpenWrt Support
Supported Since Revision https://dev.openwrt.org/changeset/46733
Supported Since Release 15.05
Supported Current Release 15.05
Unsupported
Hardware
Instruction set ARM
Sub Instruction Set ARMv7-A
Bootloader CFE
Target bcm53xx
System-On-Chip Broadcom BCM4709A0
CPU MHz 2x 1000
Flash MB 128NAND
RAM MB 256
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch Broadcom BCM4709A0
Modem No
VLAN ¿
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware
Detachable Antennas 3
Comments - WLAN 3x3:3 MIMO
Interfaces
USB ports 1x 2.0, 1x 3.0
SATA ports -
Serial Yes
JTAG ¿
Comments - USB & SATA ports
Misc
LED count ¿
Button count ¿
Power supply
Links
Forum Topic URL https://forum.openwrt.org/viewtopic.php?id=46717
WikiDevi URL https://wikidevi.com/wiki/Netgear_R7000
OEM device homepage URL
Firmware OEM Stock URL http://support.netgear.de/product/R7000
Firmware OpenWrt Install URL http://downloads.openwrt.org/chaos_calmer/15.05/bcm53xx/generic/openwrt-15.05-bcm53xx-netgear-r7000-squashfs.chk
Firmware OpenWrt Upgrade URL http://downloads.openwrt.org/chaos_calmer/15.05/bcm53xx/generic/openwrt-15.05-bcm53xx-netgear-r7000-squashfs.chk
Edit the underlying data View/Edit data

Photos

Model Number

Front:

Photo of front of the casing

Back:

Photo of back of the casing

Opening the case

Note: This will void your warranty!

  • To remove the cover do a/b/c

Main PCB

Photo of PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

**Photo of PCB with markings**

Console settings: 115200 8-N-1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

Photo of PCB with markings

Debricking

Bootlogs

Openwrt dmesg

BusyBox v1.23.2 (2015-08-24 19:14:13 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CHAOS CALMER (Bleeding Edge, r46717) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@OpenWrt:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.18.20 (buildbot@debian-amd64) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46717) ) #1 SMP Mon Aug 24 19:26:26 UTC 2015 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Netgear R7000 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c03d7640, node_mem_map c7ef8000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] PERCPU: Embedded 9 pages/cpu @c7ee1000 s5952 r8192 d22720 u36864 [ 0.000000] pcpu-alloc: s5952 r8192 d22720 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 125548K/131072K available (2910K kernel code, 106K rwdata, 792K rodata, 176K init, 276K bss, 5524K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc03a5dcc (3704 kB) [ 0.000000] .init : 0xc03a6000 - 0xc03d2000 ( 176 kB) [ 0.000000] .data : 0xc03d2000 - 0xc03ecbf8 ( 107 kB) [ 0.000000] .bss : 0xc03ecbf8 - 0xc0431d4c ( 277 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: platform modifies aux control register: 0x0a130000 -> 0x7a530001 [ 0.000000] L2C: platform provided aux values permit register corruption. [ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x7a530001 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310: enabling full line of zeros but not enabled in Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001 [ 0.000014] sched_clock: 64 bits at 400MHz, resolution 2ns, wraps every 2748779069440ns [ 0.010415] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816) [ 0.103843] pid_max: default: 32768 minimum: 301 [ 0.109879] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.118284] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.127716] CPU: Testing write buffer coherency: ok [ 0.134194] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.141514] Setting up static identity map for 0x11a80 - 0x11ab4 [ 0.151035] CPU1: Booted secondary processor [ 0.190232] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.190312] Brought up 2 CPUs [ 0.206792] SMP: Total of 2 processors activated (3188.32 BogoMIPS). [ 0.214871] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13) [ 0.225551] CPU: This may indicate a broken bootloader or firmware. [ 0.240555] NET: Registered protocol family 16 [ 0.246938] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.282389] Switched to clocksource arm_global_timer [ 0.289881] NET: Registered protocol family 2 [ 0.296238] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.305113] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.313215] TCP: Hash tables configured (established 1024 bind 1024) [ 0.321338] TCP: reno registered [ 0.325496] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.332945] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.341176] NET: Registered protocol family 1 [ 0.346792] PCI: CLS 0 bytes, default 64 [ 0.347783] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.356420] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.363886] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.376455] msgmni has been set to 245 [ 0.381790] io scheduler noop registered [ 0.386817] io scheduler deadline registered (default) [ 0.393736] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.403951] console [ttyS0] disabled [ 0.408585] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 117, base_baud = 7812500) is a 16550 [ 0.419867] console [ttyS0] enabled [ 0.428718] bootconsole [earlycon0] disabled [ 0.441023] libphy: Fixed MDIO Bus: probed [ 0.446236] bgmac: Broadcom 47xx GBit MAC driver loaded [ 0.453024] bcma: bus0: Found chip with id 53010, rev 0x00 and package 0x00 [ 0.461829] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0) [ 0.472593] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.472607] bcma: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, rev 0x01, class 0x0) [ 0.483577] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.483590] bcma: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0) [ 0.493590] bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.504124] bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.514654] bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.525188] bcma: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.535689] bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0) [ 0.546412] bcma: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0) [ 0.557149] bcma: bus0: Core 9 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0) [ 0.567915] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.567928] bcma: bus0: Core 10 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0) [ 0.580524] bcma: bus0: Core 11 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0) [ 0.591057] bcma: bus0: Core 12 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0) [ 0.601590] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.601603] bcma: bus0: Core 13 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0) [ 0.611915] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.611929] bcma: bus0: Core 14 found: I2S (manuf 0x4BF, id 0x834, rev 0x03, class 0x0) [ 0.622022] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.622035] bcma: bus0: Core 15 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0) [ 0.633765] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.633777] bcma: bus0: Core 16 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0) [ 0.647253] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.647265] bcma: bus0: Core 17 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0) [ 0.657361] bcma: bus0: Core 18 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0) [ 0.669421] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.669434] bcma: bus0: Core 19 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0) [ 0.690280] bcm_nand bcma0:18: NAND Controller rev 6.01 [ 0.720309] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 0.728270] nand: Macronix NAND 128MiB 3,3V 8-bit [ 0.734185] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 1.080421] mtd_read error while parsing (offset: 0x1CE0000)! [ 1.317781] mtd_read error while parsing (offset: 0x30E0000)! [ 1.999712] random: nonblocking pool is initialized [ 2.302171] 14 bcm47xxpart partitions found on MTD device bcm_nand [ 2.309917] Creating 14 MTD partitions on "bcm_nand": [ 2.316263] 0x000000000000-0x000000080000 : "boot" [ 2.324160] 0x000000080000-0x000000200000 : "nvram" [ 2.334398] 0x000000200000-0x000002200000 : "firmware" [ 2.414534] 0x00000020001c-0x000000600000 : "linux" [ 2.430549] 0x000000600000-0x000002200000 : "ubi" [ 2.500998] 0x000002200000-0x000002240000 : "board_data" [ 2.508925] 0x000002240000-0x000002280000 : "POT" [ 2.516123] 0x000002280000-0x000002400000 : "POT" [ 2.526171] 0x000002400000-0x000002440000 : "ML" [ 2.533275] 0x000002440000-0x000002480000 : "ML" [ 2.540387] 0x000002480000-0x0000024c0000 : "ML" [ 2.547469] 0x0000024c0000-0x000002500000 : "ML" [ 2.554547] 0x000002500000-0x000002540000 : "ML" [ 2.561625] 0x000002540000-0x000008000000 : "ML" [ 2.776152] bcm53xxspiflash spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff [ 2.785358] bcm53xxspiflash: probe of spi32766.0 failed with error -2 [ 2.824457] bcma: bus0: Using SPROM revision 11 provided by platform. [ 2.824748] bgmac bcma0:3: Found PHY addr: 30 (NOREGS) [ 2.831966] bgmac bcma0:3: Support for Roboswitch not implemented [ 2.841211] b53_common: found switch: BCM53012, rev 5 [ 2.848281] bgmac bcma0:4: Found PHY addr: 0 [ 2.855460] bgmac: Timeout waiting for reg 0x180 [ 2.861281] bgmac bcma0:4: Writing to PHY 0 register 0x0 failed [ 2.869828] bgmac: Timeout waiting for reg 0x180 [ 2.875627] bgmac bcma0:4: Reading PHY 0 register 0x0 failed [ 2.882725] bgmac bcma0:4: PHY reset failed [ 2.887961] bgmac bcma0:4: Support for Roboswitch not implemented [ 2.896644] bgmac bcma0:5: Invalid MAC addr: 00:00:00:00:00:00 [ 2.904026] bgmac bcma0:5: Using random MAC: 36:a7:7a:b8:39:be [ 2.911389] bgmac bcma0:5: Found PHY addr: 0 [ 2.918495] bgmac: Timeout waiting for reg 0x180 [ 2.924300] bgmac bcma0:5: Writing to PHY 0 register 0x0 failed [ 2.932851] bgmac: Timeout waiting for reg 0x180 [ 2.938641] bgmac bcma0:5: Reading PHY 0 register 0x0 failed [ 2.945741] bgmac bcma0:5: PHY reset failed [ 2.950986] bgmac bcma0:5: Support for Roboswitch not implemented [ 2.959626] bgmac: Unsupported core_unit 3 [ 2.964806] bgmac: probe of bcma0:6 failed with error -524 [ 2.971804] pci_host_bcm5301x bcma0:7: initializing PCIe controller [ 3.250257] pci_host_bcm5301x bcma0:7: link: UP [ 3.256060] pci_host_bcm5301x bcma0:7: PCI host bridge to bus 0000:00 [ 3.264163] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff] [ 3.272787] pci_bus 0000:00: root bus resource [io 0x0000] [ 3.279774] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 3.289736] pci 0000:00:00.0: [14e4:8012] type 01 class 0x020000 [ 3.289798] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold [ 3.289988] PCI: bus0: Fast back to back transfers disabled [ 3.297136] pci 0000:01:00.0: [14e4:4360] type 00 class 0x028000 [ 3.297176] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 3.297285] pci 0000:01:00.0: supports D1 D2 [ 3.297464] PCI: bus1: Fast back to back transfers disabled [ 3.304472] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.304491] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 3.304595] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff] [ 3.313118] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit] [ 3.322300] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.328531] pci 0000:00:00.0: bridge window [mem 0x08000000-0x080fffff] [ 3.337191] pci_host_bcm5301x bcma0:8: initializing PCIe controller [ 3.620251] pci_host_bcm5301x bcma0:8: link: UP [ 3.626056] pci_host_bcm5301x bcma0:8: PCI host bridge to bus 0001:00 [ 3.634159] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff] [ 3.642784] pci_bus 0001:00: root bus resource [io 0x0000] [ 3.649770] pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff] [ 3.659723] pci 0001:00:00.0: [14e4:8012] type 01 class 0x020000 [ 3.659781] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold [ 3.659974] PCI: bus0: Fast back to back transfers disabled [ 3.667117] pci 0001:01:00.0: [14e4:4360] type 00 class 0x028000 [ 3.667159] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 3.667266] pci 0001:01:00.0: supports D1 D2 [ 3.667439] PCI: bus1: Fast back to back transfers disabled [ 3.674446] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.674465] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 01 [ 3.674614] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff] [ 3.683137] pci 0001:01:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit] [ 3.692318] pci 0001:00:00.0: PCI bridge to [bus 01] [ 3.698547] pci 0001:00:00.0: bridge window [mem 0x40000000-0x400fffff] [ 3.707221] pci_host_bcm5301x bcma0:9: initializing PCIe controller [ 4.100253] pci_host_bcm5301x bcma0:9: link: DOWN [ 4.107373] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer) [ 4.118642] bcma: bus0: Bus registered [ 4.123507] bcma-pci-bridge 0000:01:00.0: enabling device (0140 -> 0142) [ 4.131952] bcma: bus1: Found chip with id 0x4360, rev 0x03 and package 0x01 [ 4.140824] bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0) [ 4.151522] bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0) [ 4.162347] bcma: bus1: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0) [ 4.172739] bcma: bus1: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0) [ 4.183336] bcma: bus1: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0) [ 4.194528] bcma: bus1: Found rev 17 PMU (capabilities 0x10A22B11) [ 4.194539] bcma: bus1: SPROM offset 0x800 [ 4.233790] bcma: bus1: Invalid SPROM read from the PCIe card, trying to use fallback SPROM [ 4.268590] bcma: bus1: Using SPROM revision 11 provided by platform. [ 4.268610] bcma: bus1: PMU resource config unknown or not needed for device 0x4360 [ 4.270624] bcma: bus1: Workarounds unknown or not needed for device 0x4360 [ 4.270638] bcma: bus1: Switched to core: 0x83C [ 4.270999] bcma: bus1: Bus registered [ 4.275763] bcma-pci-bridge 0001:01:00.0: enabling device (0140 -> 0142) [ 4.284209] bcma: bus2: Found chip with id 0x4360, rev 0x03 and package 0x01 [ 4.293075] bcma: bus2: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0) [ 4.303778] bcma: bus2: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0) [ 4.314602] bcma: bus2: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0) [ 4.324993] bcma: bus2: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0) [ 4.335589] bcma: bus2: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0) [ 4.346777] bcma: bus2: Found rev 17 PMU (capabilities 0x10A22B11) [ 4.346787] bcma: bus2: SPROM offset 0x800 [ 4.386037] bcma: bus2: Invalid SPROM read from the PCIe card, trying to use fallback SPROM [ 4.417712] bcma: bus2: Using SPROM revision 11 provided by platform. [ 4.417730] bcma: bus2: PMU resource config unknown or not needed for device 0x4360 [ 4.419731] bcma: bus2: Workarounds unknown or not needed for device 0x4360 [ 4.419744] bcma: bus2: Switched to core: 0x83C [ 4.420085] bcma: bus2: Bus registered [ 4.425152] TCP: cubic registered [ 4.429319] NET: Registered protocol family 17 [ 4.434992] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 4.450838] Bridge firewalling registered [ 4.455874] 8021q: 802.1Q VLAN Support v1.8 [ 4.461193] Registering SWP/SWPB emulation handler [ 4.469535] UBI: auto-attach mtd4 [ 4.473732] UBI: attaching mtd4 to ubi0 [ 4.870845] UBI: scanning is finished [ 4.893131] UBI: attached mtd4 (name "ubi", size 28 MiB) to ubi0 [ 4.900715] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.909224] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.917634] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.926259] UBI: good PEBs: 223, bad PEBs: 1, corrupted PEBs: 0 [ 4.933678] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.942625] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1803316545 [ 4.953959] UBI: available PEBs: 0, total reserved PEBs: 223, PEBs reserved for bad PEB handling: 19 [ 4.965418] UBI: background thread "ubi_bgt0d" started, PID 290 [ 4.966643] UBI: ubiblock0_0 created from ubi0:0(rootfs) [ 4.966649] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.994477] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 5.003690] Freeing unused kernel memory: 176K (c03a6000 - c03d2000) [ 5.614348] init: Console is alive [ 5.618775] init: - watchdog - [ 5.622957] External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored. [ 6.275336] usbcore: registered new interface driver usbfs [ 6.282327] usbcore: registered new interface driver hub [ 6.289068] usbcore: registered new device driver usb [ 6.641283] init: - preinit - [ 7.870271] eth0: Link is Up - 1Gbps/Full - flow control off [ 10.046979] UBIFS: background thread "ubifs_bgt0_1" started, PID 354 [ 10.147753] UBIFS: recovery needed [ 10.345562] UBIFS: recovery completed [ 10.350291] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 10.358374] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 10.369839] UBIFS: FS size: 21204992 bytes (20 MiB, 167 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs) [ 10.381834] UBIFS: reserved for root: 1001563 bytes (978 KiB) [ 10.389045] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 7338089B-10F1-41E8-BA1C-B2F91567E847, small LPT model [ 10.405766] mount_root: switching to jffs2 overlay [ 10.430598] procd: - early - [ 10.434306] procd: - watchdog - [ 11.141332] procd: - ubus - [ 12.170977] procd: - init - [ 16.838991] NET: Registered protocol family 10 [ 16.848422] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 16.861774] Loading modules backported from Linux version master-2015-07-21-0-g47cd203 [ 16.871733] Backport generated by backports.git backports-20150626-0-gc1a4168 [ 16.882227] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.893760] nf_conntrack version 0.5.0 (1964 buckets, 7856 max) [ 16.970885] xt_time: kernel timezone is -0000 [ 16.984629] cfg80211: World regulatory domain updated: [ 16.991119] cfg80211: DFS Master region: unset [ 16.996588] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 17.008849] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.018906] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.028951] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 17.038989] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 17.050878] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 17.062757] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 17.072901] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 17.082928] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 17.110202] PPP generic driver version 2.4.2 [ 17.117181] NET: Registered protocol family 24 [ 17.136903] b43-phy0: Broadcom 4360 WLAN found (core revision 42) [ 17.144607] bcma: bus1: Switched to core: 0x812 [ 17.151135] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1) [ 17.161202] b43: probe of bcma1:1 failed with error -95 [ 17.167808] b43-phy1: Broadcom 4360 WLAN found (core revision 42) [ 17.175461] bcma: bus2: Switched to core: 0x812 [ 17.181121] b43-phy1 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1) [ 17.191171] b43: probe of bcma2:1 failed with error -95 [ 17.197816] Broadcom 43xx driver loaded [ Features: PNL ] [ 17.208962] usbcore: registered new interface driver brcmfmac [ 20.423129] device eth0.1 entered promiscuous mode [ 20.429162] device eth0 entered promiscuous mode [ 20.442516] br-lan: port 1(eth0.1) entered forwarding state [ 20.449567] br-lan: port 1(eth0.1) entered forwarding state [ 20.890343] eth0: Link is Up - 1Gbps/Full - flow control off [ 22.441107] br-lan: port 1(eth0.1) entered forwarding state


Notes

Tags

toh/netgear/r7000.txt · Last modified: 2015/12/14 16:09 by tmomas