User Tools

Site Tools


toh:ubiquiti:ubiquiti_edgerouter_x_er-x_ka

Ubiquiti EdgeRouter X (ER-X) / EdgeRouter X-SFP (ER-X-SFP)

This types of router are some small boxes with 5 fixed LAN-ports. The advantage of the EdgeRouter X-SFP is the support of 5 PoE-outputs and the option to attach a SFP-module.

Supported Versions

Hardware Highlights

Voltage: Ubiquiti EdgerouterX SFP uses AOZ1212 DC/DC voltage regulator that works from a 4.5V to 27V input voltage range.

Installation

Currently only trunk OpenWRT has support for this device. To obtain a factory image that can be booted via TFTP, set up an OpenWRT build environment and compile for:
Target system: Ralink RT288x/RT3xxx
Subtarget: MT7621 based boards
Target profile: Ubiquiti EdgeRouter X

The resulting bin/ramips/openwrt-ramips-mt7621-ubnt-erx-initramfs-kernel.bin file can be booted via option 1 in the boot menu available via a serial connection. After this factory image boots, use sysupgrade to flash the sysupgrade image.

If you can confirm that OpenWrt is running on this device (i.e. you or someone else has tested it), please update the data accordingly. → Click View/Edit data

Flash Layout

This is the factory layout and it can be used as is? The factory layout is not using the whole flash, 524288 bytes(256pages) are missing.

We should keep in that line for easyer return to stock firmware. maybe Ubiquiti is storing a "magic thing" there.

offset(dez) size(dez) name offset(hex) size(hex)
0 524288 bootloader 0x00000000 0x00080000
524288 393216 config 0x00080000 0x00060000
917504 393216 eeprom 0x000E0000 0x00060000
1310720 3145728 kernel 0x00140000 0x00300000
4456448 3145728 kernel2 (squashfs later) 0x00440000 0x00300000
7602176 259784704 rootfs (overlay later) 0x00740000 0x0F7C0000

OEM easy installation

Installation only by Serial AFAIK.

OEM installation using the TFTP method

A nice Blog-post with the full story to get it installed can be found here

generic.flashing.tftp

Specific values needed for tftp

FIXME Enter values for "FILL-IN" below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain "tftp")
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

Upgrading OpenWrt

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

LuCI Web Upgrade Process

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:

cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:

cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

PoE out on EdgeRouter X

The router can supply PoE out (passthrough) on the eth4 port. This is controlled with GPIO 0.

To enable PoE out (passthrough) on port eth4, do:

echo 0 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio0/direction
echo 1 > /sys/class/gpio/gpio0/value

PoE out on EdgeRouter X-SFP

The router can supply PoE on the LAN-ports. This is controlled by a PCA9555A with GPIO 0..4.

In order to get this running you need:

  • install "kmod-i2c-gpio-custom" (pulls gpio and algo-bitbang)
  • install "kmod-gpio-pca953x"
  • "insmod i2c-gpio-custom bus0=0,3,4"
  • "echo pca9555 0x25 >/sys/bus/i2c/devices/i2c-0/new_device"
  • export the GPIOs 496..500 (/sys/class/gpio/)

After reboot you need to run insmod and the echo line below to allow on/off functionality.

insmod i2c-gpio-custom bus0=0,3,4
echo pca9555 0x25 >/sys/bus/i2c/devices/i2c-0/new_device

Turn on POE all ports except eth0(WAN)
#eth0 WAN port
echo "496" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio496/direction
echo "0" > /sys/class/gpio/gpio496/value
#eth1
echo "497" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio497/direction
echo "1" > /sys/class/gpio/gpio497/value
#eth2
echo "498" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio498/direction
echo "1" > /sys/class/gpio/gpio498/value
#eth3
echo "499" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio499/direction
echo "1" > /sys/class/gpio/gpio499/value
#eth4
echo "500" > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio500/direction
echo "1" > /sys/class/gpio/gpio500/value



#turn all POE off
echo "0" > /sys/class/gpio/gpio496/value
echo "0" > /sys/class/gpio/gpio497/value
echo "0" > /sys/class/gpio/gpio498/value
echo "0" > /sys/class/gpio/gpio499/value
echo "0" > /sys/class/gpio/gpio500/value

Switch Ports (for VLANs)

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2
LAN 3 EXAMPLE 1
LAN 4 EXAMPLE 0

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The Ubiquiti EdgeRouter X ER-X has the following buttons:

BUTTON Event
EXAMPLE Reset reset
EXAMPLE Secure Easy Setup ses
EXAMPLE No buttons at all. -

Hardware

Info

General
Brand Ubiquiti
Model EdgeRouter X
Versions
Device Type Router
Availability Available
Comments - general
OpenWrt Support
Supported Since Revision https://dev.openwrt.org/changeset/47881
Supported Since Release ¿
Supported Current Release ¿
Unsupported
Hardware
Instruction set MIPS32
Sub Instruction Set MIPS32 1004K series
Bootloader U-Boot
Target ramips
System-On-Chip MediaTek MT7621AT
CPU MHz 2x 880
Flash MB 256
RAM MB 256
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
Switch MediaTek MT7621
Modem No
VLAN ¿
Comments - network ports
Wireless
WLAN 2.4GHz -
WLAN 5.0GHz -
WLAN Hardware
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports -
SATA ports -
Serial Yes
JTAG Yes
Comments - USB & SATA ports
Misc
LED count ¿
Button count ¿
Power supply
Links
Forum Topic URL https://forum.openwrt.org/viewtopic.php?pid=299587
WikiDevi URL https://wikidevi.com/wiki/Ubiquiti_Networks_EdgeRouter_X
OEM device homepage URL https://www.ubnt.com/edgemax/edgerouter-x/
Firmware OEM Stock URL http://dl.ubnt.com/firmwares/edgemax/v1.7.0/ER-e50.v1.7.0.4783374.tar
Firmware OpenWrt Install URL
Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/snapshots/trunk/ramips/mt7621/openwrt-ramips-mt7621-ubnt-erx-squashfs-sysupgrade.tar
Edit the underlying data View/Edit data

Photos

Serial Port location and pin indentification

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

EdgeRouter X SFP

PCB top PCB bottom PCB PoE-section

Opening the case

Note: This will void your warranty!

Two crosshead screws are present on one side of the router, unscrew these and the top of the casing comes right off. No warranty-void stickers present of any kind. The serial port is prepopulated with header pins.

Main PCB:
Insert photo of PCB

Serial

Insert photo of PCB with Serial connection pins

Serial connection parameters 57600, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader Mods

Hardware mods

Currently none.

Bootlogs

OEM bootlog

=================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xb, 1/0 = 660/364 2D000000 PLL4 FB_DL: 0xf, 1/0 = 549/475 3D000000 PLL2 FB_DL: 0x16, 1/0 = 586/438 59000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 16 rank 0 fine = 32 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00001C1C ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 8 11 10 11 6 12 6 7 9 10 | 8 13 8 11 9 9 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =28 DQS1 = 28 ================================================================== bit DQS0 bit DQS1 0 (1~53)27 8 (1~53)27 1 (2~53)27 9 (1~54)27 2 (1~54)27 10 (0~53)26 3 (0~54)27 11 (2~52)27 4 (1~56)28 12 (1~53)27 5 (1~54)27 13 (1~55)28 6 (1~55)28 14 (1~55)28 7 (1~55)28 15 (1~54)27 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 12 9 12 11 11 7 12 6 8 10 10 | 10 14 9 11 9 10 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff00aa dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0080 DQ loop=13, cmp_err_1 = ffff0080 DQ loop=12, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=12, finish count=2 byte:0, (DQS,DQ)=(9,8) byte:1, (DQS,DQ)=(8,8) 20,data:89 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Jan 27 2015 - 17:52:09) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffb0000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 8ffe13a0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [01 DA 90 95 46] Device found in MTK table, ID: 1da, EXT_ID: 909546 Support this Device in MTK table! 1da select_chip [NAND]select ecc bit:12, sparesize :112 spare_per_sector=28 Signature matched and data read! load_fact_bbt success 2047 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=112, mtd->erasesize=131072 devinfo.iowidth=8 .. UBNT e50 13-02079-18 44D9E707138C UBNT BD type=e50, mac=44D9E707138C, s/n=44D9E707138C, mrev=18, k_idx=0 ============================================ Ralink UBoot Version: 4.3.S.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Jan 27 2015 Time:17:52:09 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 4  4  3 You choosed 3  0 3: System Boot system code via Flash. ## Booting image at bfd40000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1676117 Bytes = 1.6 MB Load Address: 80001000 Entry Point: 803654a0 .......................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 803654a0) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC Linux version 3.10.14-UBNT (root@edgeos-builder2) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Mon Feb 16 12:59:27 PST 2015 The CPU feqenuce set to 880 MHz GCMP present CPU0 revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 10000000 @ 00000000 (usable) Zone ranges: Normal [mem 0x00000000-0x0fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x0fffffff] Detected 3 available secondary CPU(s) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. PERCPU: Embedded 7 pages/cpu @81203000 s6656 r8192 d13824 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 Kernel command line: console=ttyS1,57600n8 ubi.mtd=7 root=ubi0_0 rootfstype=ubifs rootsqimg=squashfs.img rootsqwdir=w rw PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Writing ErrCtl register=00050184 Readback ErrCtl register=00050184 Memory: 254860k/262144k available (3507k kernel code, 7284k reserved, 1010k data, 212k init, 0k highmem) Hierarchical RCU implementation. NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU1 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 1: done. launch: starting cpu2 launch: cpu2 gone! CPU2 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 2: done. launch: starting cpu3 launch: cpu3 gone! CPU3 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 3: done. Brought up 4 CPUs devtmpfs: initialized NET: Registered protocol family 16 bio: create slab <bio-0> at 0 Switching to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) squashfs: version 4.0 (2009/01/31) Phillip Lougher Registering unionfs 2.5.13 (for 3.10.34) aufs 3.10.x-20140915 msgmni has been set to 497 io scheduler noop registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A Ralink gpio driver initialized i2cdrv_major = 218 loop: module loaded flash manufacture id: 1c, device id 70 15 EN25QH16(1c 70151c70) (2048 Kbytes) mtd .name = raspi, .size = 0x00200000 (2M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 1 MTD partitions on "raspi": 0x000000000000-0x000000080000 : "SPI_FLASH" MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 804b0430 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [01 DA 90 95 46, 00909546] Device found in MTK table, ID: 1da, EXT_ID: 909546 Support this Device in MTK table! 1da NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 112 [NAND]select ecc bit:12, sparesize :112 spare_per_sector=28 Scanning device for bad blocks Signature matched and data read! load_fact_bbt success 2047 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Creating 7 MTD partitions on "MT7621-NAND": 0x000000000000-0x00000ff80000 : "ALL" 0x000000000000-0x000000080000 : "Bootloader" 0x000000080000-0x0000000e0000 : "Config" 0x0000000e0000-0x000000140000 : "eeprom" 0x000000140000-0x000000440000 : "Kernel" 0x000000440000-0x000000740000 : "Kernel2" 0x000000740000-0x00000ff00000 : "RootFS" [mtk_nand] probe successfully! UBNT BD mac 44d9e707138c kidx 0 mrev 18 serial 44D9E707138C type e50 rdm_major = 253 GMAC1_MAC_ADRH -- : 0x000044d9 GMAC1_MAC_ADRL -- : 0xe707138c Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x000044d9 GMAC1_MAC_ADRL -- : 0xe707138c PROC INIT OK! Ralink I2C Init TCP: cubic registered NET: Registered protocol family 17 NET: Registered protocol family 15 UBI: attaching mtd7 to ubi0 UBI: scanning is finished UBI: attached mtd7 (name "RootFS", size 247 MiB) to ubi0 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 1982, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1428435120 UBI: available PEBs: 0, total reserved PEBs: 1982, PEBs reserved for bad PEB handling: 40 UBI: background thread "ubi_bgt0d" started, PID 51 UBIFS: background thread "ubifs_bgt0_0" started, PID 52 UBIFS: mounted UBI device 0, volume 0, name "troot" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 244428800 bytes (233 MiB, 1925 LEBs), journal size 12189696 bytes (11 MiB, 96 LEBs) UBIFS: reserved for root: 4952683 bytes (4836 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID E6F01834-6938-4C48-AB84-503A3CF12D34, small LPT model VFS: Mounted root (aufs filesystem) on device 0:12. devtmpfs: mounted Freeing unused kernel memory: 212K (8046b000 - 804a0000) Algorithmics/MIPS FPU Emulator v1.5 INIT: version 2.88 booting aufs au_lkup_dentry:223:date[68]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[68]: I/O Error, both of real entry and whiteout found, localtime, err -5 mkdir: can't create directory '/dev/shm/network': No such file or directory aufs au_lkup_dentry:223:ntpdate[173]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:init[1]: I/O Error, both of real entry and whiteout found, localtime, err -5 INIT: Entering runlevel: 2 Unable to open file: /dev/tpm0 can't open any entropy source Maybe RNG device modules are not loaded aufs au_lkup_dentry:223:rsyslogd[308]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:cron[321]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:cron[322]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:ubnt-cfgd[332]: I/O Error, both of real entry and whiteout found, localtime, err -5 [....] Starting routing daemon: ribaufs au_lkup_dentry:223:zebra[349]: I/O Error, both of real entry and whiteout found, localtime, err -5 [?25l[?1c7[ ok 8[?25h[?0c. [....] Starting EdgeOS router: migrateaufs au_lkup_dentry:223:sg[388]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[400]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[407]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[422]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:vyatta_config_m[389]: I/O Error, both of real entry and whiteout found, localtime, err -5 rl-system configureaufs au_lkup_dentry:223:sg[462]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[464]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[467]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[469]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[470]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[472]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[475]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:rsyslogd[502]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[509]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:ln[510]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:ln[510]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:ln[510]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:netplugd[306]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[523]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[525]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[537]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[539]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[551]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[553]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[565]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[567]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[583]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[587]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[589]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[603]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[605]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[611]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:ntpd[634]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[637]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:usermod[640]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[646]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[649]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[653]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[659]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[658]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sshd[688]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[690]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[696]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[698]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[700]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:sudo[704]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:lighttpd[707]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:logger[722]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[723]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:php-cgi[708]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[725]: I/O Error, both of real entry and whiteout found, localtime, err -5 aufs au_lkup_dentry:223:date[726]: I/O Error, both of real entry and whiteout found, localtime, err -5 [?25l7[FAIL8[?25h failed! Welcome to EdgeOS ubnt ttyS1 By logging in, accessing, or using the Ubiquiti product, you acknowledge that you have read and understood the Ubiquiti License Agreement (available in the Web UI at, by default, http://192.168.1.1) and agree to be bound by its terms. ubnt login:


OpenWrt bootlog

=================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL2 FB_DL: 0xc, 1/0 = 741/283 31000000 PLL3 FB_DL: 0xd, 1/0 = 517/507 35000000 PLL4 FB_DL: 0x15, 1/0 = 543/481 55000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 16 rank 0 fine = 32 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00001C1D ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 9 13 10 13 8 12 7 7 10 10 | 9 13 7 12 7 10 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =29 DQS1 = 28 ================================================================== bit DQS0 bit DQS1 0 (2~55)28 8 (1~53)27 1 (1~52)26 9 (1~52)26 2 (1~52)26 10 (1~52)26 3 (1~52)26 11 (2~55)28 4 (2~57)29 12 (2~55)28 5 (1~53)27 13 (1~56)28 6 (1~54)27 14 (1~54)27 7 (1~55)28 15 (1~56)28 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 14 12 15 13 13 10 14 8 8 12 10 | 11 13 7 12 8 10 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff2240 DQS loop = 14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=14, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2 DQ loop=15, cmp_err_1 = ffff00a0 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1 DQ loop=14, cmp_err_1 = ffff0080 DQ loop=13, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=13, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Jan 27 2015 - 17:52:09) Board: Ralink APSoC DRAM: 256 MB relocate_code Pointer at: 8ffb0000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 8ffe13a0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [01 DA 90 95 46] Device found in MTK table, ID: 1da, EXT_ID: 909546 Support this Device in MTK table! 1da select_chip [NAND]select ecc bit:12, sparesize :112 spare_per_sector=28 Signature matched and data read! load_fact_bbt success 2047 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=112, mtd->erasesize=131072 devinfo.iowidth=8 .. UBNT e50 13-02079-18 44D9E79393C7 UBNT BD type=e50, mac=44D9E79393C7, s/n=44D9E79393C7, mrev=18, k_idx=1 ============================================ Ralink UBoot Version: 4.3.S.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Jan 27 2015 Time:17:52:09 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 0 3: System Boot system code via Flash. ## Booting image at c0040000 ... Image Name: MIPS OpenWrt Linux-4.4.6 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1513707 Bytes = 1.4 MB Load Address: 80001000 Entry Point: 80001000 ........................ Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 256 Starting kernel ... [ 0.000000] Linux version 4.4.6 (derecho@prorsus) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 r49166) ) #2 SMP Thu Apr 14 18:13:22 UTC 2016 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is UBNT-ERX [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 10000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 10 pages/cpu @8120b000 s8416 r8192 d24352 u40960 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=0003aa00 [ 0.000000] Readback ErrCtl register=0003aa00 [ 0.000000] Memory: 254720K/262144K available (3479K kernel code, 161K rwdata, 812K rodata, 208K init, 248K bss, 7424K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:256 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns [ 0.010000] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.100000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.100000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.100000] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.190000] Synchronize counters for CPU 1: done. [ 0.200000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.200000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.200000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.200000] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.290000] Synchronize counters for CPU 2: done. [ 0.300000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.300000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.300000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.300000] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.390000] Synchronize counters for CPU 3: done. [ 0.400000] Brought up 4 CPUs [ 0.400000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.410000] pinctrl core: initialized pinctrl subsystem [ 0.420000] NET: Registered protocol family 16 [ 0.490000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.500000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.510000] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.520000] clocksource: Switched to clocksource GIC [ 0.540000] NET: Registered protocol family 2 [ 0.550000] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.560000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.570000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.580000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.600000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.610000] NET: Registered protocol family 1 [ 0.620000] futex hash table entries: 1024 (order: 3, 32768 bytes) [ 0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.650000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.670000] io scheduler noop registered [ 0.680000] io scheduler deadline registered (default) [ 0.690000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.700000] console [ttyS0] disabled [ 0.710000] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 33, base_baud = 3125000) is a 16550A [ 0.730000] console [ttyS0] enabled [ 0.730000] console [ttyS0] enabled [ 0.740000] bootconsole [early0] disabled [ 0.740000] bootconsole [early0] disabled [ 0.760000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 0.770000] Allocate 16 byte aligned buffer: 804c3210 [ 0.780000] Enable NFI Clock [ 0.790000] # MTK NAND # : Use HW ECC [ 0.800000] Device found in MTK table, ID: 1da, EXT_ID: 909546 [ 0.810000] Support this Device in MTK table! 1da [ 0.820000] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xda [ 0.830000] nand: AMD/Spansion NAND 256MiB 3,3V 8-bit [ 0.840000] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128 [ 0.860000] [NAND]select ecc bit:12, sparesize :112 spare_per_sector=28 [ 0.870000] Scanning device for bad blocks [ 1.570000] 6 ofpart partitions found on MTD device MT7621-NAND [ 1.580000] Creating 6 MTD partitions on "MT7621-NAND": [ 1.590000] 0x000000000000-0x000000080000 : "u-boot" [ 1.600000] 0x000000080000-0x0000000e0000 : "u-boot-env" [ 1.610000] 0x0000000e0000-0x000000140000 : "factory" [ 1.620000] 0x000000140000-0x000000440000 : "kernel1" [ 1.630000] 0x000000440000-0x000000740000 : "kernel2" [ 1.640000] 0x000000740000-0x00000ff00000 : "ubi" [ 1.660000] [mtk_nand] probe successfully! [ 1.660000] Signature matched and data read! [ 1.670000] load_fact_bbt success 2047 [ 1.680000] netif_napi_add() called with weight 128 on device eth%d [ 1.710000] libphy: mdio: probed [ 1.730000] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver [ 1.740000] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 10 [ 1.760000] mt7621_wdt 1e000100.wdt: Initialized [ 1.770000] NET: Registered protocol family 10 [ 1.780000] NET: Registered protocol family 17 [ 1.790000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.810000] 8021q: 802.1Q VLAN Support v1.8 [ 1.820000] UBI: auto-attach mtd5 [ 1.830000] ubi0: attaching mtd5 [ 4.270000] ubi0: scanning is finished [ 4.300000] ubi0: attached mtd5 (name "ubi", size 247 MiB) [ 4.310000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.320000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.330000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.350000] ubi0: good PEBs: 1982, bad PEBs: 0, corrupted PEBs: 0 [ 4.360000] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.370000] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1689714530 [ 4.390000] ubi0: available PEBs: 0, total reserved PEBs: 1982, PEBs reserved for bad PEB handling: 40 [ 4.410000] ubi0: background thread "ubi_bgt0d" started, PID 289 [ 4.420000] block ubiblock0_0: created from ubi0:0(rootfs) [ 4.430000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.450000] hctosys: unable to open rtc device (rtc0) [ 4.460000] UBIFS error (ubi0:0 pid 1): init_constants_early: too few LEBs (11), min. is 17 [ 4.480000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.490000] Freeing unused kernel memory: 208K (8045c000 - 80490000) [ 5.180000] init: Console is alive [ 5.180000] init: - watchdog - [ 5.370000] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.790000] random: procd urandom read with 28 bits of entropy available [ 8.810000] UBIFS (ubi0:1): default file-system created [ 8.820000] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 351 [ 8.940000] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 8.960000] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 8.980000] UBIFS (ubi0:1): FS size: 243032064 bytes (231 MiB, 1914 LEBs), journal size 12189696 bytes (11 MiB, 96 LEBs) [ 9.000000] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 9.010000] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID AAD1669E-8BEF-4D72-B307-63F0E2358AA3, small LPT model [ 9.040000] mount_root: overlay filesystem has not been fully initialized yet [ 9.050000] mount_root: switching to jffs2 overlay [ 9.080000] procd: - early - [ 9.090000] procd: - watchdog - [ 9.830000] procd: - ubus - [ 9.890000] procd: - init - Please press Enter to activate this console. [ 10.280000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.300000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.310000] nf_conntrack version 0.5.0 (3983 buckets, 15932 max) [ 10.460000] xt_time: kernel timezone is -0000 [ 10.470000] PPP generic driver version 2.4.2 [ 10.480000] NET: Registered protocol family 24 [ 13.750000] device eth0.1 entered promiscuous mode [ 13.760000] device eth0 entered promiscuous mode [ 13.770000] br-lan: port 1(eth0.1) entered forwarding state [ 13.780000] br-lan: port 1(eth0.1) entered forwarding state [ 15.780000] br-lan: port 1(eth0.1) entered forwarding state [ 20.240000] random: nonblocking pool is initialized BusyBox v1.24.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- DESIGNATED DRIVER (Bleeding Edge, r49166) ----------------------------------------------------- * 2 oz. Orange Juice Combine all juices in a * 2 oz. Pineapple Juice tall glass filled with * 2 oz. Grapefruit Juice ice, stir well. * 2 oz. Cranberry Juice ----------------------------------------------------- root@OpenWrt:/#


Notes

Space for additional notes, links to forum threads or other resources, …

Tags

toh/ubiquiti/ubiquiti_edgerouter_x_er-x_ka.txt · Last modified: 2017/03/17 19:43 by valentt