User Tools

Site Tools


toh:zyxel:nwa1123-ac

ZyXEL NWA1123-AC

  • WLAN access point with PoE
  • Dual band 2.4 GHz and 5 GHz simultaneously
  • 1 Gigabit LAN port with PoE 802.3af
  • smoke detector design

CURRENTLY NOT SUPPORTED / SUPPORT NOT CLEAR / WIP

Hardware Highlights

SoC Ram Flash Network USB Serial JTag
Atheros AR9342 rev 3 64MiB 16MiB 1 x 1 No Yes No

Flash memory info:

Flash memory data sheet: http://pdf1.alldatasheet.com/datasheet-pdf/view/267918/MCNIX/MX25L12845EMI-10G.html

Manufacturer's site: http://www.zyxel.com/products_services/nwa1120_series.shtml

Manual: ftp://ftp.zyxel.com/NWA1123-AC/user_guide/NWA1123-AC_1.00.pdf

Forum: https://forum.openwrt.org/viewtopic.php?id=56608

Buttons

The NWA1123-AC has only one button.

BUTTON Event
Reset reset

Hardware

Info

Instruction set: MIPS
Vendor: Qualcomm Atheros
Bootloader: U-Boot
System-On-Chip: Atheros AR9342 rev 3
CPU @Frq 560.000MHz
Flash size: 16 MiB
Flash Chip: MX25L12845EMI-10G
RAM size: 64 MiB
RAM Chip: ?
Wireless No1: ???? SoC-integrated: QCA9558-AT4A w/ 3x3 MIMO for 2.4GHz 802.11b/g/n
Wireless No2: ???? distinct Chip: AR9580-AR1A w/ 3x3 MIMO for 5GHz 802.11a/n/ac
Switch: ???? RealTek RTL8366RB (Gigabit, VLAN)
Modem: none
USB: No
Serial: Yes
JTAG: ??

Photos

Model Number

Front:

Back:

Plug connectors on the back (ethernet with PoE, separate power connector):

Opening the case

Note: This will void your warranty!

  • To remove the cover remove the four screws on the backside.

Main PCB: back side

Main PCB: front side

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

There are four pins on the front side of the PCB, see the photo below. GND is marked with a square, VCC +3.3 V is marked with a circle. Starting numbering GND with 1, the pinout is as following:

  • 1 GND
  • 2 RD (receive data - input to AP)
  • 3 TD (transmit data - output from AP)
  • 4 VCC +3.3V

Photo of PCB with markings

The position of the serial connector on the PCB is marked with a red ellipse:

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

I could not find a JTAG port on this device.

Debricking

Bootloader Mods

  1. you could read about bootloader in general

Hardware mods

Currently none.

Flash ROM memory map

OEM memory map

0x000000000000-0x000000040000 : "u-boot" (256 KiB)
0x000000040000-0x000000050000 : "u-boot-env" (64 KiB)
0x000000050000-0x000000850000 : "rootfs" (8192 KiB)
0x000000850000-0x000000940000 : "uImage" (960 KiB)
0x000000940000-0x000000fa0000 : "reserve" (6528 KiB)
0x000000fa0000-0x000000fe0000 : "config" (256 KiB)
0x000000fe0000-0x000000ff0000 : "mib0" (64 KiB)
0x000000ff0000-0x000001000000 : "ART" (64 KiB)

OEM loaded linux kernel modules

~ # lsmod
Module                  Size  Used by    Tainted: P  
xt_tcpudp 2176 4 - Live 0x831e7000
xt_physdev 1760 2 - Live 0x831ed000
iptable_filter 1552 1 - Live 0x8394a000
ip_tables 10656 1 iptable_filter, Live 0x831e4000
x_tables 12672 3 xt_tcpudp,xt_physdev,ip_tables, Live 0x831f4000
ath_pktlog 16192 0 - Live 0x831c0000 (P)
umac 1628576 1 ath_pktlog, Live 0x83200000
ath_dev 237760 2 ath_pktlog,umac, Live 0x83bc0000 (P)
ath_dfs 52064 1 umac, Live 0x83a30000 (P)
ath_rate_atheros 33488 3 ath_pktlog,umac,ath_dev, Live 0x83ac0000 (P)
ath_hal 627664 4 ath_pktlog,umac,ath_dev,ath_rate_atheros, Live 0x83b00000 (P)
asf 7232 5 ath_pktlog,umac,ath_dev,ath_dfs,ath_hal, Live 0x83a26000 (P)
adf 12432 3 umac,ath_dev,ath_hal, Live 0x83a28000 (P)
athrs_gmac 36944 0 - Live 0x83950000

Bootlogs

OEM bootlog

U-Boot 1.1.4-g3ba2fcff-dirty (Aug 27 2013 - 12:33:31) U-boot MI124 DRAM: Tap value selected = 0xf [0x0 - 0x1f] Setting 0xb8116290 to 0x30602d0f 64 MB Top of RAM usable for U-Boot at: 84000000 Reserving 220k for U-Boot at: 83fc8000 Reserving 192k for malloc() at: 83f98000 Reserving 44 Bytes for Board Info at: 83f97fd4 Reserving 48 Bytes for Global Data at: 83f97fa4 Reserving 128k for boot params() at: 83f77fa4 Stack Pointer at: 83f77f88 Now running in RAM - U-Boot at: 83fc8000 Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18 flash size 16MB, sector count = 256 Flash: 16 MB pci_init_board: PCIe PLL not set for 40MHz refclk BOARD IS NOT CALIBRATED!!! In: serial Out: serial Err: serial Net: ag934x_enet_initialize... Fetching MAC Address from 0x83fed7b8 wasp reset mask:c02200 WASP ----> F1 PHY * : cfg1 0x80000000 cfg2 0x7114 eth0: 00:30:ab:11:20:e1 F1Phy reg init ATHR_AUTONEG_ADVERT:1DE1 ATHR_1000BASET_CONTROL:200 ATHR_PHY_CONTROL:3100 ATHRSF1_PHY: Port 0, Neg Success ATHRSF1_PHY: unit 0 phy addr 0 eth0 up ethact=eth0 ************ Post Result ******************* POST memory PASSED POST uart PASSED POST ethernet PASSED Hit any key to stop autoboot: 4  3  2  1  0 ## Booting image at 9f850000 ... Image Name: Linux Kernel Image Created: 2013-10-31 6:06:08 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 951427 Bytes = 929.1 kB Load Address: 80002000 Entry Point: 801f84f0 Verifying Checksum at 0x9f850040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 801f84f0) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... Booting Atheros AR934x Linux version 2.6.31--LSDK-9.2.0_U10.1020-00006-g848b629-dirty (dnisw3@SW3L01) (gcc version 4.3.3 (GCC) ) #1 Thu Oct 31 14:02:45 CST 2013 flash_size passed from bootloader = 16 arg 1: console=ttyS0,115200 arg 2: root=31:02 arg 3: rootfstype=jffs2 arg 4: init=/sbin/init arg 5: mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),8192k(rootfs),960k(uImage),6528k(reserve),256k(config),64k(mib0),64k(ART) arg 6: mem=64M CPU revision is: 0001974c (MIPS 74Kc) ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 400 ahb 200 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) User-defined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),8192k(rootfs),960k(uImage),6528k(reserve),256k(config),64k(mib0),64k(ART) mem=64M PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 47784k/65536k available (2026k kernel code, 17684k reserved, 486k data, 156k init, 0k highmem) NR_IRQS:128 plat_time_init: plat time init done Calibrating delay loop... 279.55 BogoMIPS (lpj=559104) Mount-cache hash table entries: 512 ****************ALLOC*********************** Packet mem: 802ae5c0 (0xe00000 bytes) ******************************************** NET: Registered protocol family 16 PCI init:ath_pcibios_init ath_pcibios_init(294): PCI CMD write: 0x356 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:00.0: PME# disabled Returning IRQ 64 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 ATH GPIOC major 0 JFFS2 version 2.2 (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc. fuse init (API version 7.12) msgmni has been set to 93 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A console [ttyS0] enabled brd: module loaded 8 cmdlinepart partitions found on MTD device ath-nor0 Creating 8 MTD partitions on "ath-nor0": 0x000000000000-0x000000040000 : "u-boot" 0x000000040000-0x000000050000 : "u-boot-env" 0x000000050000-0x000000850000 : "rootfs" 0x000000850000-0x000000940000 : "uImage" 0x000000940000-0x000000fa0000 : "reserve" 0x000000fa0000-0x000000fe0000 : "config" 0x000000fe0000-0x000000ff0000 : "mib0" 0x000000ff0000-0x000001000000 : "ART" TCP cubic registered NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver sit0: Disabled Privacy Extensions NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 4 athwdt_init: Registering WDT success ath_otp_init: Registering OTP success ath_clksw_init: Registering Clock Switch Interface success VFS: Mounted root (jffs2 filesystem) readonly on device 31:2. Freeing unused kernel memory: 156k freed init started: BusyBox v1.01 (2013.10.31-06:02+0000) multi-call binary ATHR_GMAC: Length per segment 1536 ATHR_GMAC: fifo cfg 3 01f00140 ATHR_GMAC: RX TASKLET - Pkts per Intr:100 ATHR_GMAC: Mac address for unit 0:bfff0000 ATHR_GMAC: 00:30:ab:11:20:e1 ATHR_GMAC: Max segments per packet : 1 ATHR_GMAC: Max tx descriptor count : 128 ATHR_GMAC: Max rx descriptor count : 128 ATHR_GMAC: Mac capability flags : 2380 1+0 records in 1+0 records out athr_gmac_ring_alloc Allocated 2048 at 0x83941800 athr_gmac_ring_alloc Allocated 2048 at 0x83941000 WASP ----> F1e PHY Setting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY... ATHR_AUTONEG_ADVERT:DE1 ATHR_1000BASET_CONTROL:200 ATHR_PHY_CONTROL:1000 ATHRSF1_PHY: Port 0, Neg Success ATHRSF1_PHY: unit 0 phy addr 0 ADDRCONF(NETDEV_UP): eth0: link is not ready SIOCGIFFLAGS: No such device apcfg: Skip default verifying. device eth0 entered promiscuous mode apcfg: Skip default verifying. Password changed. athstats 80211stats wlanconfig pktlogconf pktlogdump radartool **** drop_caches_sysctl_handler: all done timer added ...**** apcfg: Skip default verifying. SEC_MODE=WPA apcfg: Skip default verifying. apcfg: Skip default verifying. Args: 1 adf: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved insmod: cannot open module `/lib/modules/2.6.31/net/ath_spectral.ko': No such file or directory ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved insmod: cannot open module `/lib/modules/2.6.31/net/hst_tx99.ko': No such file or directory ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_ahb: 10.1.389 (Atheros/multi-bss) __ath_attach: Set global_scn[0] ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 Enterprise mode: 0x00000000 Restoring Cal data from Flash Green-AP : Green-AP : Attached ath_get_caps[5942] rx chainmask mismatch actual 3 sc_chainmak 0 ath_get_caps[5917] tx chainmask mismatch actual 3 sc_chainmak 0 ath_attach_dfs[11817] dfsdomain 0 ath_tx_paprd_init sc 83bf0000 PAPRD Enabled SC Callback Registration for wifi0 wifi0: Atheros 9340: mem=0xb8100000, irq=2 ath_pci: 10.1.389 (Atheros/multi-bss) ath_pci_probe PCI device id is 003c :003c ath_pci 0000:00:00.0: ath DEBUG: sc=0x83bffc00 ol_ath_pci_configure : num_desired MSI set to 0 Using PCI Legacy Interrupt __ol_ath_attach: ath_attach TODO ol_ath_attach() BMI inited. ol_ath_attach() BMI Get Target Info. ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_ath_attach() configure Target . ol_transfer_bin_file 1582: Download Board data len 2116 ol_ath_download_firmware: Using 0x1234 for the remainder of init ol_transfer_bin_file 1574: Download OTP data len 5972 ol_transfer_bin_file 1620: Download Firmware data len 187520 ol_ath_attach() Download FW. ol_ath_attach() HT Create . ol_ath_attach() HIF Claim. ol_ath_attach() BMI Done. ol_ath_attach() WMI attached. wmi_handle 83000000 +HWT -HWT HTC Service:0x0300 ep:1 TX flow control disabled TXRX: Created pdev 83bff600 wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event num_rf_chain : 00000002 ht_cap_info: : 0000085b vht_cap_info : 338001b2 vht_supp_mcs : 0000fffa LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256 idx 0 req 1 num_units 0 num_unit_info 2 unit size 404 actual units 145 chunk 0 len 58580 requested ,ptr 0x3120000 FIRMWARE:P 145 V 16 T 443 wmi_ready_event_rx: WMI UNIFIED READY event ol_ath_connect_htc() WMI is ready ol_ath_set_host_app_area TODO ol_ath_attach() connect HTC. target uses HTT version 2.1; host uses 2.1 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 Skipping VHT80 channel 5825 ol_ath_phyerr_attach: called OL Resmgr Init-ed Green-AP : Green-AP : Attached Green-AP : Attached ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=83109974, radar_info=839f1c48 ol_ath_rtt_meas_report_attach: called ol_ath_attach() UMAC attach . ol_if_dfs_configure: called ol_if_dfs_configure: UNINIT domain ol_if_dfs_disable: called __ol_ath_attach: init tx/rx TODO __ol_ath_attach: hard_header_len reservation 58 __ol_ath_attach: dev name wifi1 SC Callback Registration for wifi1 insmod: cannot open module `/lib/modules/2.6.31/net/wlan_me.ko': No such file or directory Initializing Pktlogs for 11ac 1+0 records in 1+0 records out 1+0 records in 1+0 records out 756 ath_attach_dfs[11817] dfsdomain 0 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 Skipping VHT80 channel 5660 Skipping VHT80 channel 5680 Skipping VHT80 channel 5700 Creating ap for ZyXEL on wlan_vap_create : enter. devhandle=0x83bcc2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 wlan_vap_create : exit. devhandle=0x83bcc2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1. VAP device ath0 created Added ath0 mode master Invalid command : bgscan Interface doesn't accept private ioctl... HALDbg (8BE0): Operation not permitted Invalid command : noedgech WARNING: Fragmentation with HT mode NOT ALLOWED!! Error for wireless request "Set Fragmentation Threshold" (8B24) : SET failed on device ath0 ; Invalid argum DES SSID SET=ZyXEL ent. ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 /etc/ath/makeVAP: 464: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent Invalid command : setVowExt /etc/ath/makeVAP: 507: APNAME: not found acparams no private ioctls. Invalid command : set_vsp_enable Interface doesn't accept private ioctl... setPhyRestartWar (8BE0): Operation not permitted Invalid command : setVowExtStats Created ath0 mode ap for ZyXEL lo no wireless extensions. sit0 no wireless extensions. eth0 no wireless extensions. br0 no wireless extensions. wifi0 no wSetting Max Stations:64 ireless extensions. wifi1 no wireless extensions. apcfg: Skip default verifying. lo no wireless extensions. sit0 no wireless extensions. eth0 no wireless extensions. br0 no wireless extensions. wifi0 no wireless extensions. wifi1 no wireless extensions. device ath0 entered promiscuous mode br0: port 2(ath0) entering forwarding state ARPING to 192.168.1.2 from 192.168.1.2 via br0 Sent 1 probes (1 broadcast(s)) Received 0 reply apcfg: Skip default verifying. ath_paprd_cal sc 83bf0000 chan_mask 3 PAPRD excessive failure disabling PAPRD now device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state device ath0 left promiscuous mode br0: port 2(ath0) entering disabled state device eth0 entered promiscuous mode device ath0 entered promiscuous mode br0: port 2(ath0) entering forwarding state interface ath8 does not exist! SIOCGIFFLAGS: No such device ip_tables: (C) 2000-2006 Netfilter Core Team iptables v1.4.5: unknown option `--dport' Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.5: unknown option `--dport' Try `iptables -h' or 'iptables --help' for more information. Bad argument `tcp' Try `iptables -h' or 'iptables --help' for more information. Bad argument `udp' Try `iptables -h' or 'iptables --help' for more information. SEC_MODE=WPA apcfg: Skip default verifying. Modules already loaded Creating ap for ZyXEL on ath_ioctl: SIOC80211IFCREATE CALLED wmi_unified_vdev_create_send: ID = 0 VAP Addr = 4c:9e:ff:90:bf:62: TXRX: Created vdev 831049c0 (4c:9e:ff:90:bf:62) VAP device ath8 created TXRX: ol_txrx_peer_find_add_id: peer 83a13000 ID 187 TXRX: ol_txrx_peer_find_add_id: peer 83a13000 ID 171 Added ath8 mode master Invalid command : bgscan Invalid command : HALDbg Invalid command : ATHDebug ol_ath_vap_set_param: VAP param unsupported param:127 value:0 Setting vdev param = 1a, value = 1 Invalid command : noedgech Invalid command : set_swapled Invalid command : set_ledcustom Interface doesn't accept private ioctl... AMPDU (8BE0): Operation not permitted Interface doesn't accept private ioctl... AMPDUFrames (8BE0): Operation not permitted Interface doesn't accept private ioctlol_ath_vap_set_param: VAP param unsupported param:43 value:0 ... AMPDULim (8BE0): Operation not permitted ol_ath_vap_set_param: VAP param unsupported param:7 value:1 WARNING: Fragmentation with HT mode NOT ALLOWED!! Error for wireless request "Set Fragmentation Threshold" (8B24) : SET failed on device ath8 ; Invalid argum DES SSID SET=ZyXEL ent. ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 OL vap_stop + wmi_unified_vdev_stop_send OL vap_stop - STOPPED EVENT for vap 0 /etc/ath/makeVAP: 464: cannot create /proc/sys/dev/ath/htdupieenable: Directory nonexistent Setting vdev param = 3, value = 100 Setting vdev param = d, value = 1 Invalid command : setVowExt Invalid command : setKeySrchAlways Setting vdev param = 2a, value = 0 ol_ath_vap_set_param: VAP param is now supported param:62 value:0 /etc/ath/makeVAP: 533: APNAME: not found acparams no private ioctls. Invalid command : set_vsp_enable Invalid command : setPhyRestartWar Invalid command : setVowExtStats Created ath8 mode ap for ZyXEL lo no wireless extensions. sit0 no wireless extensions. eth0 no wireless extensions. br0 no wireless extensions. wifi0 no wSetting Max Stations:64 ireless extensions. wifi1 no wireless extensions. ol_ath_vap_set_param: VAP param unsupported param:35 value:0 Setting vdev param = 1e, value = 1 apcfg: Skip default verifying. lo no wireless extensions. sit0 no wireless extensions. eth0 no wireless extensions. br0 no wireless extensions. wifi0 no wireless extensions. wifi1 no wireless extensions. OL vap_stop + wmi_unified_vdev_stop_send OL vap_stop - STOPPED EVENT for vap 0 OL vap_start + OL vap_start - ol_vdev_start_resp_ev ol_ath_vap_join: join operation is only for STA/IBSS mode ol_ath_wmm_update: Setting vdev param = 3, value = 100 Notification to UMAC VAP layer FWLOG: [42334] WHAL_ERROR_RESET_CHANNF1 ( ) FWLOG: [42334] WAL channel change (force reset) freq=5200, flags=10 mode=0 rx_ok=1 tx_ok=1 device ath8 entered promiscuous mode br0: port 3(ath8) entering forwarding state arping: bind apcfg: Skip default verifying. Setting vdev param = 12, value = 1 wmi_unified_vdev_stop_send STOPPED EVENT for vap 0 OL vap_start + OL vap_start - ol_vdev_start_resp_ev ol_ath_vap_join: join operation is only for STA/IBSS mode Setting vdev param = 3, value = 100 Notification to UMAC VAP layer ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: ol_ath_wmm_update: device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state device ath0 left promiscuous mode br0: port 2(ath0) entering disabled state device ath8 left promiscuous mode br0: port 3(ath8) entering disabled state device eth0 entered promiscuous mode device ath0 entered promiscuous mode br0: port 2(ath0) entering forwarding state device ath8 entered promiscuous mode br0: port 3(ath8) entering forwarding state iptables v1.4.5: unknown option `--dport' Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.5: unknown option `--dport' Try `iptables -h' or 'iptables --help' for more information. Bad argument `tcp' Try `iptables -h' or 'iptables --help' for more information. Bad argument `udp' Try `iptables -h' or 'iptables --help' for more information. route: SIOC[ADD|DEL]RT: No such process ARPING to 192.168.1.2 from 192.168.1.2 via br0 Sent 1 probes (1 broadcast(s)) Received 0 reply Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1 le: /tmp/apath0 br0: port 2(ath0) entering disabled state DEVICE IS DOWN ifname=ath0 Could not connec DEVICE IS DOWN ifname=ath0 t to kernel driver. Using interface ath0 with hwaddr 4c:9e:ff:90:bf:61 and ssid 'ZyXEL' random: Cannot read from /dev/random: Resource temporarily unavailable random: Only 0/20 bytes of strong random data available from /dev/random random: Not enough entropy pool available for secure operations WPA: Not enough entropy in random pool for secure operations - update keys later when the first station connects br0: port 2(ath0) entering forwarding state Configuration fi ieee80211_ioctl_siwmode: imr.ifm_active=643, new mode=3, valid=1 le: /tmp/apath8wmi_unified_vdev_stop_send STOPPED EVENT for vap 0 br0: port 3(ath8) entering disabled state ol_ath_vap_set_param: VAP param unsupported param:32 value:0 ol_ath_vap_set_param: VAP param unsupported param:121 value:1 DEVICE IS DOWN ifname=ath8 Could not connec DEVICE IS DOWN ifname=ath8 t to kernel drivol_ath_vap_set_param: VAP param unsupported param:32 value:0 er. Using interface ath8 with hwaddr 4c:9e:ff:90:bf:62 and ssid 'ZyXEL' random: Cannot rol_ath_vap_set_param: VAP param unsupported param:74 value:1 ead from /dev/ra Group Keyidx set=1 ndom: Resource twmi_unified_vdev_install_key_send Setting Key for Macaddress:0x62bf90ff9e4c emporarily unavaKeyix=1 Keylen=32 Keyflags=1 Cipher=2 Keydata=ilable random: 0x86 Only 0/20 bytes 0xbc of strong random0xf7 data available 0xeb from /dev/random0xd6 random: Not en0xec ough entropy poo0x6 l available for 0x97 secure operation0x68 s WPA: Not enou0xa8 gh entropy in ra0xca ndom pool for se0x8d cure operations 0x5f - update keys la0xc5 ter when the fir0x9b st station conne0xe1 cts 0xd3 0xef 0xb9 0x3 0x4e 0x8b 0xae 0x27 0x6f 0xef 0xb 0xc3 0xe3 0x4 0xd1 0x12 ol_ath_vap_set_param: VAP param unsupported param:74 value:0 TXRX: ol_txrx_peer_find_add_id: peer 83a13000 ID 139 TXRX: sec spec for peer 83a13000 (4c:9e:ff:90:bf:62): mcast key of type 4 Setting vdev param = 1f, value = 1 ol_ath_vap_set_param: VAP param unsupported param:32 value:1 OL vap_stop + wmi_unified_vdev_stop_send OL vap_stop - STOPPED EVENT for vap 0 OL vap_start + OL vap_start - ol_vdev_start_resp_ev ol_ath_vap_join: join operation is only for STA/IBSS mode ol_ath_wmm_update: Setting vdev param = 3, value = 100 Notification to UMAC VAP layer br0: port 3(ath8) entering forwarding state Invalid command : txstbc Invalid command : rxstbc FWLOG: [46778] WAL_DBGID_SECURITY_ENCR_EN ( ) FWLOG: [46778] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) bind: Address already in use mini_httpd: started as root without requesting chroot(), warning only bind: Address already in use mini_httpd: started as root without requesting chroot(), warning only apcfg: Skip default verifying. apcfg: Skip default verifying. apcfg: Skip default verifying. date: invalid date `00000.0' Ebtables v2.0 registered Ebtables v2.0 unregistered NWA1123-AC mips #1 Thu Oct 31 14:02:45 CST 2013 (none) NWA1123-AC login:


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Tags

toh/zyxel/nwa1123-ac.txt · Last modified: 2015/12/12 07:38 by tmomas